The document provides instructions for disassembling and assembling the freewheel stator component of a torque converter. It outlines 35 steps to disassemble the component, removing parts like the impeller, carrier shaft, stator, and turbine. It then lists 12 steps for reassembling the component, including installing the turbine, stator, carrier shaft, impeller, seals, and other parts. Cleanliness is emphasized as important during disassembly and assembly.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950H WHEEL LOADER J5J
Configuration: 950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE
Disassembly and Assembly
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Power Train
Media Number -RENR8867-05 Publication Date -01/06/2014 Date Updated -27/06/2014
i02348371
Torque Converter from Transmission, Output Transfer
Gears - Separate
SMCS - 3003-076
Separation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B
138-7573 Link Bracket 3
1U-9200 Lever Puller Hoist 1
Start By:
A. Remove the torque converter, the transmission, and the output transfer gears. Refer to
Disassembly and Assembly, "Torque Converter, Transmission and Output Transfer Gears -
Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01173182
1. Disconnect harness assemblies (2) and (5) .
2. Remove tube assembly (4) .
3. Remove bolts (3) and transmission oil pump (1) .
Illustration 2 g01173184
4. Remove tube assembly (6) .
2/5
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 7. Reposition torque converter (8), transmission (9), and output transfer gears (10). The
combined weight of torque converter (8), transmission (9), and output transfer gears (10) is
approximately 816 kg (1800 lb).
8. Remove Tooling (A) .
Illustration 6 g01173189
9. Attach Tooling (B) and a suitable lifting device to torque converter (8). The weight of
torque converter (8) is approximately 170 kg (375 lb).
Illustration 7 g01173190
10. Remove bolts (11) .
4/5
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g01173192
11. Remove bolts (12) .
Illustration 9 g01173193
12. Remove Torque converter (8) from transmission (9) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Mar 31 08:59:26 UTC+0800 2020
5/5
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950H WHEEL LOADER J5J
Configuration: 950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE
Disassembly and Assembly
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Power Train
Media Number -RENR8867-05 Publication Date -01/06/2014 Date Updated -27/06/2014
i06170973
Torque Converter (Freewheel Stator) - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-7405 Eyebolt 2
C 2P-8312 Retaining Ring Pliers 1
Start By:
A. Separate the torque converter from the transmission and from the output transfer gears.
Refer to Disassembly and Assembly, "Torque Converter from Transmission, Output
Transfer Gears - Separate".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
1/11
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g01173843
Illustration 2 g01173844
1. Remove bolts (2) and transmission hydraulic control relief valve (3) from torque converter
housing (1) .
2. Remove torque converter inlet relief valve (4) and the O-ring seal.
Illustration 3 g01173845
2/11
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 6 g01173853
7. Remove bolt (11) from drive gear shaft (12) .
Illustration 7 g03835382
8. Install Tooling (B) in pump drive gear (13) .
9. Lift pump drive gear (13) and drive gear shaft (12) out of the housing bore.
10. Remove drive gear shaft (12) and bearing (14) from pump drive gear (13) .
11. Use Tooling (A) and a suitable lifting device to remove the torque converter housing
assembly. The weight of the torque converter housing assembly is approximately 113 kg
(250 lb).
4/11
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 8 g01173861
12. Remove drive gear (15) .
Illustration 9 g01173862
13. Remove retaining ring (16) .
14. Use a soft faced hammer in order to free the bearing from the carrier assembly. Remove
output shaft (17) from the carrier assembly.
5/11
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 10 g03835392
15. Remove seal ring (18) from output shaft (17) .
16. Use a suitable press to remove bearing (19) .
Illustration 11 g01173864
17. Remove bolts (20) and impeller (21) .
Illustration 12 g01173866
18. Reposition impeller (21) .
19. Remove retaining ring (22) and spacer (24) from carrier shaft (23) .
20. Remove stator (25) .
6/11
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 13 g01173867
21. Remove retaining ring (26) and washer (27) from stator (25) . Repeat this Step for the other
side of stator (25) .
Illustration 14 g01173868
22. Remove race (28) , rollers (29) , springs (30) , and cam (31) from stator (25) .
Illustration 15 g01173870
7/11
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 23. Remove spacer (32) from impeller (21) .
Illustration 16 g01173872
24. Use a suitable press to remove carrier shaft (24) from impeller (21) .
Illustration 17 g01173917
25. Remove bolts (33) and drive gear (34) .
8/11
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 18 g01173920
26. Remove bearing (35) from impeller (21) .
Illustration 19 g01173923
27. Remove seal ring (36) from carrier shaft (23) .
28. If necessary, remove locating dowel (37) .
Illustration 20 g01173921
29. Remove ring (40) , retaining ring (38) , and cover (39) from housing (41) .
9/11
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 21 g01173924
30. Use Tooling (C) in order to remove retaining ring (42) .
Illustration 22 g01173925
31. Remove spacer (43) and O-ring seal (44) .
Illustration 23 g01173926
32. Turn the housing onto the opposite side and remove turbine assembly (45) .
10/11
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 24 g01173927
33. Remove bolts (46) in order to separate turbine (47) from hub (48) .
34. If necessary, remove locating dowel (49) .
Illustration 25 g01173928
35. Remove roller bearing (50) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Mar 31 09:00:25 UTC+0800 2020
11/11
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950H WHEEL LOADER J5J
Configuration: 950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE
Disassembly and Assembly
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Power Train
Media Number -RENR8867-05 Publication Date -01/06/2014 Date Updated -27/06/2014
i06171004
Torque Converter (Freewheel Stator) - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-7405 Eyebolt 2
C 2P-8312 Retaining Ring Pliers 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/12
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g01173928
Illustration 2 g01173927
1. If necessary, install locating dowel (49) .
2. Install bearing (50) so that the notch in bearing (50) is in alignment with locating dowel
(49) .
3. Install turbine (47) to hub (48) and install bolts (46) . Tighten bolts (46) to a torque of 60 ±
7 N·m (44 ± 5 lb ft).
Illustration 3 g01173926
4. Install turbine assembly (45) into the impeller housing.
2/12
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 4 g01173925
5. Install spacer (43) and O-ring seal (44) .
Illustration 5 g01173924
6. Use Tooling (C) to install retaining ring (42) .
Illustration 6 g01173921
7. Install cover (39) , retaining ring (38) , and ring (40) on housing (41) .
3/12
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 7 g01173923
8. If necessary, install locating dowel (37) .
9. Install seal ring (36) on carrier shaft (23) .
Illustration 8 g01173920
10. Install bearing (35) in impeller (21) .
4/12
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Illustration 9 g01173917
11. Install drive gear (34) and bolts (33) . Tighten bolts (33) to a torque of 105 ± 15 N·m (77 ±
11 lb ft).
Illustration 10 g01173872
12. Use a suitable press to install carrier shaft (23) in impeller (21) .
Illustration 11 g01173870
13. Install spacer (32) on impeller (21) .
5/12
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 12 g01173868
Note: If necessary, raise the temperature of stator (25) in order to install cam (31) .
14. Install cam (31) , springs (30) , rollers (29) , and race (28) in stator (25) .
Note: Install springs (30) with the maximum number of loops toward the outside diameter
of cam (31) .
Illustration 13 g01173867
15. Install washer (27) and retaining ring (26) in stator (25) . Repeat this step for the other side
of stator (25) .
6/12
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 14 g01173866
16. Install stator (25) on impeller (21) .
17. Install spacer (24) and retaining ring (22) over carrier shaft (23) .
Illustration 15 g01173864
18. Install impeller (21) and bolts (20) . Tighten bolts (20) to a torque of 60 ± 7 N·m (44 ± 5 lb
ft).
7/12
950H WHEEL LOADER J5J00001-UP (MACHINE) POWERED BY C7 ENGINE(X...
2020/3/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...