Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 740 ARTICULATED TRUCK WWD
Configuration: 740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i07435098
Rear Power Take-Off (RPTO) - Install - If Equipped
SMCS - 1165-012-RE
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01134277
1. Install sleeve bearing (12) in the flywheel housing with Tooling (A). The split in the sleeve
bearing should be located at Angle (Y), which is 15 ± 1 degrees from the vertical centerline.
The bearing should be installed to Depth (Z), which is 2.0 ± 0.5 mm (0.08 ± 0.02 inch).
2. Install cover (10) and the bolts on the back side of the flywheel housing.
Illustration 2 g01134279
3. Install sleeve bearing (11) in the flywheel housing with Tooling (A). The split in the sleeve
bearing should be located at Angle (X), which is 15 ± 1 degrees from the horizontal
centerline. The bearing should be installed to Depth (Z), which is 2.0 ± 0.5 mm
(0.08 ± 0.02 inch).
4. Install cover (9) and the bolts on the back side of the flywheel housing.
2/4
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01134263
5. Use Tooling (A) and install sleeve bearing (8) in adapter (2). Install the O-ring seal on the
adapter.
Illustration 4 g01134262
6. Position gear assembly (6) and gear assembly (7) in the flywheel housing.
3/4
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01115921
7. Position idler gears (5) and retainer assemblies (4). Install bolts (3). Tighten bolts (3) to a
torque of 100 ± 20 N·m (74 ± 15 lb ft).
8. Lubricate the O-ring seal on the adapters with clean engine oil. Position adapters (2) on the
flywheel housing and install bolts (1).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 23 23:39:57 UTC+0800 2020
4/4
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 740 ARTICULATED TRUCK WWD
Configuration: 740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i05009357
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure Type 1
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
(5/8 - 18 NF by 7 inch)
1
B 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01044774
1. Remove one bolt (4). Install Tooling (B) and a suitable lifting device to vibration damper
(3) and crankshaft pulley (1). The weight of vibration damper (3) and crankshaft pulley (1)
is approximately 57 kg (125 lb).
2. Remove one bolt (2). Install Tooling (A).
3. Remove remaining bolts (2). Remove vibration damper (3) and crankshaft pulley (1) from
the crankshaft.
4. Remove bolts (4). Remove spacer (5). Remove vibration damper (3) from crankshaft pulley
(1). The weight of vibration damper (3) is approximately 34 kg (75 lb).
Installation Procedure Type 1
Table 2
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
(5/8 - 18 NF by 7 inch)
1
B 138-7575 Link Bracket 1
C 4C-5592 Anti-Seize Compound 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/5
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. NOTICE
Thoroughly inspect the viscous damper for signs of leakage or for signs
of a dented (damaged) case. Either of these conditions can cause the
weight to make contact with the case. This can affect the viscous
damper's operation.
Illustration 2 g01044774
1. Position vibration damper (3) on crankshaft pulley (1). The weight of vibration damper (3)
is approximately 34 kg (75 lb).
2. Install spacer (5) on the vibration damper. Install bolts (4) and tighten the bolts to a torque
of 135 ± 20 N·m (100 ± 15 lb ft).
3. Install Tooling (B) and a suitable lifting device on vibration damper (3) and crankshaft
pulley (1). The weight of vibration damper (3) and crankshaft pulley (1) is approximately
57 kg (125 lb). Install the vibration damper and the crankshaft pulley on Tooling (A).
4. Apply Tooling (C) to bolts (2). Install the bolts. Remove Tooling (A) and install the
remaining bolts. Tighten the bolts to a torque of 215 ± 40 N·m (159 ± 30 lb ft).
Removal Procedure Type 2
Table 3
Required Tools
3/5
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Tool Part Number Part Description Qty
A -
Guide Stud
(5/8 - 18 NF by 7 inch)
1
Illustration 3 g03181887
1. Remove pulley (1) and the belt. Refer to Belt Tensioner - Remove and Install.
Illustration 4 g03181936
2. Remove one bolt (2). Install Tooling (A) and a suitable lifting device to vibration damper
(4). Remove bolts (2), spacer (3), and vibration damper (4). The weight of vibration damper
(4) is approximately 13.7 kg (30.22 lb).
Installation Procedure Type 2
Table 4
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
(5/8 - 18 NF by 7 inch)
1
C 4C-5592 Anti-Seize Compound 1
4/5
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 5 g03181936
1. Install Tooling (A) into the Crankshaft. Position vibration damper (4) onto Tooling (A). The
weight of vibration damper (3) is approximately 14 kg (30 lb).
2. Apply Tooling (C) onto bolts (2). Install spacer (3) and bolts (2).
Illustration 6 g03181887
3. Install pulley (1). Refer to Belt Tensioner - Remove and Install.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 23 23:40:52 UTC+0800 2020
5/5
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 740 ARTICULATED TRUCK WWD
Configuration: 740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i02210415
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the vibration damper and the pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g01044861
1. Use Tooling (A) or a punch and hammer in order to puncture three or more holes in wear
sleeve (2).
2. Use Tooling (A) to remove the wear sleeve.
3. Use Tooling (A) or a punch and hammer in order to puncture three or more holes in
crankshaft front seal (1).
4. Use Tooling (A) to remove the crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 23 23:41:48 UTC+0800 2020
2/2
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 740 ARTICULATED TRUCK WWD
Configuration: 740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i02210423
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B
5P-1733 Seal Locator 1
5P-1737 Bolt 3
9S-8858 Nut (Seal Installer) 1
6V-6142 Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The crankshaft front seal and the wear sleeve must be replaced at the same time.
Once the crankshaft front seal and the wear sleeve are separated, these components cannot
be used again.
Note: Do not use any type of lubricant during the installation of the crankshaft front seal
and the wear sleeve.
1. Clean the outside diameter of the crankshaft.
1/2
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g01116116
2. Use Tooling (B) to install crankshaft front seal (1) and wear sleeve (2).
Note: Install the crankshaft front seal with the arrow that shows the direction of crankshaft
rotation toward the front of the engine.
End By:
a. Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration
Damper and Pulley - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 23 23:42:44 UTC+0800 2020
2/2
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 740 ARTICULATED TRUCK WWD
Configuration: 740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i02210465
Front Cover - Remove
SMCS - 1166-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01007036
1/2
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. 1. Remove button head screws (1).
2. Remove nuts (5) and spacers (4) from studs (3).
3. Remove front cover (2) and the seal from the front housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 23 23:43:39 UTC+0800 2020
2/2
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 740 ARTICULATED TRUCK WWD
Configuration: 740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i02210470
Front Cover - Install
SMCS - 1166-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01007036
1/2
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 1. Position the seal and front cover (2) on studs (3).
2. Install button head screws (1). Tighten the button head screws to a torque of 21 ± 3 N·m
(15 ± 2 lb ft).
3. Install spacers (4) and nuts (5) on studs (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 23 23:44:35 UTC+0800 2020
2/2
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 740 ARTICULATED TRUCK WWD
Configuration: 740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i02210493
Gear Group (Front) - Remove
SMCS - 1206-011
Removal Procedure
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
1/3
740 OEM Articulated Truck WWD00001-UP (MACHINE) POWERED BY C15 Engi...
2020/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...