1. Remove the transmission, torque converter, and transfer gears from the tractor. Lift the assembly weighing approximately 1320 kg onto stands.
2. Attach lifting brackets and remove the bolts and nuts securing the 340 kg transfer gears to the transmission. Separate the transfer gears and remove o-rings.
3. Remove the final o-ring seal from the transmission. Install the transfer gears by reversing the removal steps.
This document provides instructions for assembling and disassembling components of the torque converter and transfer gears for a 621H wheel tractor. It describes 22 steps for assembling the torque converter, including installing various bearings, seals, and fasteners in the proper order. It also describes removing and installing the transfer gears while the tractor is either off or on the chassis. The disassembly procedure describes removing bearing cages, shims, and bearings from the transfer gear case.
The document provides instructions for assembling and disassembling the torque converter of a 621H wheel tractor. It describes 22 steps for assembling the torque converter, requiring tools like a driver group, dial indicator group, and retaining ring pliers. It also describes removing and installing the transfer gears of a 621H wheel tractor, both off chassis and in chassis. The procedures include disconnecting hoses and harness assemblies, removing brackets and seals, and lifting components with lifting devices.
The document provides instructions for assembling and disassembling the torque converter of a 621H wheel tractor. It describes 22 steps for assembling the torque converter, requiring tools like a driver group, dial indicator group, and retaining ring pliers. It also describes removing and installing the transfer gears of a 621H wheel tractor, both off chassis and in chassis. The procedures include disconnecting hoses and harness assemblies, removing brackets and seals, and lifting components with lifting devices.
This document provides instructions for assembling and disassembling components of the torque converter and transfer gears for a 621H wheel tractor. It describes 22 steps for assembling the torque converter, including installing various bearings, seals, and fasteners in the proper order. It also describes removing and installing the transfer gears while the tractor is either off or on the chassis. The disassembly procedure lists 6 steps for disassembling the transfer gear case, including removing bearing cages and shims.
This document provides instructions for assembling and disassembling components of the torque converter and transfer gears for a 621H wheel tractor. It describes 22 steps for assembling the torque converter, including installing various bearings, seals, and fasteners in the proper order. It also describes removing and installing the transfer gears while the tractor is either off or on the chassis. The disassembly procedure lists 6 steps for disassembling the transfer gear case, including removing bearing cages and shims.
The document provides instructions for assembling and disassembling the torque converter of a 621H wheel tractor. It describes 22 steps for assembling the torque converter, requiring tools like a driver group, dial indicator group, and retaining ring pliers. It also describes removing and installing the transfer gears of a 621H wheel tractor, both off chassis and in chassis. The procedures include disconnecting hoses and harness assemblies, removing brackets and seals, and lifting components with lifting devices.
This document provides instructions for assembling and disassembling components of the torque converter and transfer gears for a 621H wheel tractor. It describes 22 steps for assembling the torque converter, including installing various bearings, seals, and fasteners in the proper order. It also describes removing and installing the transfer gears while the tractor is either off or on the chassis. The disassembly procedure describes removing bearing cages, shims, and bearings from the transfer gear case.
This document provides instructions for assembling and disassembling components of the torque converter and transfer gears for a 621H wheel tractor. It describes 22 steps for assembling the torque converter, including installing various bearings, seals, and fasteners in the proper order. It also describes removing and installing the transfer gears while the tractor is either off or on the chassis. The disassembly procedure describes removing bearing cages, shims, and bearings from the transfer gear case.
This document provides instructions for assembling and disassembling components of the torque converter and transfer gears for a 621H wheel tractor. It describes 22 steps for assembling the torque converter, including installing various bearings, seals, and fasteners in the proper order. It also describes removing and installing the transfer gears while the tractor is either off or on the chassis. The disassembly procedure describes removing bearing cages, shims, and bearings from the transfer gear case.
The document provides instructions for assembling and disassembling the torque converter of a 621H wheel tractor. It describes 22 steps for assembling the torque converter, requiring tools like a driver group, dial indicator group, and retaining ring pliers. It also describes removing and installing the transfer gears of a 621H wheel tractor, both off chassis and in chassis. The procedures include disconnecting hoses and harness assemblies, removing brackets and seals, and lifting components with lifting devices.
The document provides instructions for assembling and disassembling the torque converter of a 621H wheel tractor. It describes 22 steps for assembling the torque converter, requiring tools like a driver group, dial indicator group, and retaining ring pliers. It also describes removing and installing the transfer gears of a 621H wheel tractor, both off chassis and in chassis. The procedures include disconnecting hoses and harness assemblies, removing brackets and seals, and lifting components with lifting devices.
This document provides instructions for assembling and disassembling components of the torque converter and transfer gears for a 621H wheel tractor. It describes 22 steps for assembling the torque converter, including installing various bearings, seals, and fasteners in the proper order. It also describes removing and installing the transfer gears while the tractor is either off or on the chassis. The disassembly procedure lists 6 steps for disassembling the transfer gear case, including removing bearing cages and shims.
This document provides instructions for assembling and disassembling components of the torque converter and transfer gears for a 621H wheel tractor. It describes 22 steps for assembling the torque converter, including installing various bearings, seals, and fasteners in the proper order. It also describes removing and installing the transfer gears while the tractor is either off or on the chassis. The disassembly procedure lists 6 steps for disassembling the transfer gear case, including removing bearing cages and shims.
The document provides instructions for assembling and disassembling the torque converter of a 621H wheel tractor. It describes 22 steps for assembling the torque converter, requiring tools like a driver group, dial indicator group, and retaining ring pliers. It also describes removing and installing the transfer gears of a 621H wheel tractor, both off chassis and in chassis. The procedures include disconnecting hoses and harness assemblies, removing brackets and seals, and lifting components with lifting devices.
This document provides instructions for assembling and disassembling components of the torque converter and transfer gears for a 621H wheel tractor. It describes 22 steps for assembling the torque converter, including installing various bearings, seals, and fasteners in the proper order. It also describes removing and installing the transfer gears while the tractor is either off or on the chassis. The disassembly procedure describes removing bearing cages, shims, and bearings from the transfer gear case.
This document provides instructions for assembling and disassembling components of the torque converter and transfer gears for a 621H wheel tractor. It describes 22 steps for assembling the torque converter, including installing various bearings, seals, and fasteners in the proper order. It also describes removing and installing the transfer gears while the tractor is either off or on the chassis. The disassembly procedure describes removing bearing cages, shims, and bearings from the transfer gear case.
Caterpillar Cat 345C and 345C L Hydraulic Excavator (Prefix PJW) Service Repa...fijsekkdmdm2w
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, applying anti-seize compound, installing various seals and gears, and adjusting bearing preload using shims. Precision is required to prevent damage to seals and ensure proper engagement of gears. Lifting devices and care are needed due to components weighing up to 127 kg.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336E and 336E L Excavator (Prefix KED) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for assembling a travel motor on an excavator. It describes 27 steps to assemble internal components like seals, springs, and bearings. These components include pistons, a cam plate, and a rotating assembly. The final steps connect the travel motor to the final drive and install exterior covers. Proper assembly requires using the correct tools and lubricants, and ensuring parts are aligned and torques are set correctly.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to disassemble the pump by removing components like bolts, sensors, valves, springs, pistons, gears, and bearings. The assembly section lists 48 steps to reinstall these components in reverse order, noting the need to heat some bearings before installation and ensure proper placement of pins, seals, and other parts. Precautions are provided for releasing spring forces. Required tools include various pliers, pins, and links to aid in removal and installation of components.
Caterpillar Cat 330F and 330F L Excavator (Prefix GHT) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling a 330F excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, brake piston, rotating assembly, pistons, seals, and other parts. Tools required include retaining ring pliers, a bearing puller, bolts, threaded rods, and other hardware. Safety precautions are provided to release spring forces carefully.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling the travel motor on a 336D2L excavator. It describes 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, springs, seals, relief valves, plugs, and more. Precautions are provided to watch for spring forces and contain fluids. Tools needed include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Reassembly will follow the disassembly steps in reverse order.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and over 15 additional parts. The goal is to allow maintenance and repair of these core powertrain systems.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 336D L Excavator (Prefix JBF) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for installing a unit injector sleeve on a Caterpillar C9 engine. It lists the required tools and gives step-by-step details for cleaning the sleeve and cylinder head bore, applying seals and retaining compound, and installing the sleeve using a hammer and installer tool. Proper installation is important to prevent leaks that could cause low pressure or excess oil consumption.
Caterpillar Cat 926 and 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing the cylinder head assembly on a 3204 vehicular engine. It describes:
1) Removing the cylinder head assembly by loosening hoses, removing bolts, and lifting it off with a hoist.
2) Cleaning and installing a new gasket before lowering the cylinder head back onto the cylinder block and tightening bolts in a specific sequence and torque.
3) Checking the flatness of the cylinder head and block surfaces during installation.
This document provides instructions for disassembling and assembling the torque converter and transmission of a Caterpillar 938F wheel loader. It details removing over 40 individual parts in 21 steps to disassemble the torque converter. A further 44 steps describe disassembling the transmission by removing components like shafts, gears, seals, and clutches. Precise tools and lifting devices are specified to carefully remove heavy parts. Reassembly is outlined in reverse order with notes to check components for wear and replace as needed.
Caterpillar Cat 325C and 325C L Excavator (Prefix BKW) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs to clean all parts thoroughly, apply lubricants, and install the parts in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Tools required include a transmission repair stand, link brackets, retaining ring pliers, and other specialized tools.
This document provides instructions for disassembling and assembling the piston pump of a 623G wheel scraper. Some key steps include:
1. Marking all mating components for alignment during assembly.
2. Removing various seals, springs, spools, and other internal parts from the pump housing and head.
3. Checking the preload on bearings during assembly by measuring clearance between the pump head and housing.
4. Cleaning all parts thoroughly before assembly and applying a light oil film. Precise alignment of marked components is important.
This document provides instructions for disassembling and assembling axle shaft assemblies for a 938F wheel loader. It describes removing components like the axle housing groups, axle shaft assembly, planetary carrier assembly, and installing new components in reverse order. Key steps include using various tools to remove retaining rings, planetary gears, and installing new bearings and seals at specified temperatures while ensuring proper torque specifications are met.
The document provides instructions for removing and installing fuel injection pumps on a Caterpillar 3406C diesel engine. Key steps include using various tools to hold components in place, loosening and removing bushings, seals and pumps. Reinstallation involves aligning pins and slots, installing spacers and seals correctly, and checking rack travel measurements to ensure proper installation. The document also describes disassembling and assembling the fuel injection pumps and fuel injection pump housing.
The document provides step-by-step instructions for disassembling and assembling the final drives of a 350L excavator. Key steps include removing the final drives and travel motors, disassembling the internal components of the final drives which include multiple planetary gear sets, carriers, and a sun gear, and then reassembling the final drives in reverse order. Proper cleaning, application of lubricants, and torque specifications are noted throughout to ensure correct reassembly.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, brake piston, rotating group, and seals. The instructions describe taking identifying marks on parts and cleaning components to prevent contamination. Reassembly is done in reverse order.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Caterpillar Cat 345C and 345C L Hydraulic Excavator (Prefix PJW) Service Repa...fijsekkdmdm2w
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, applying anti-seize compound, installing various seals and gears, and adjusting bearing preload using shims. Precision is required to prevent damage to seals and ensure proper engagement of gears. Lifting devices and care are needed due to components weighing up to 127 kg.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336E and 336E L Excavator (Prefix KED) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for assembling a travel motor on an excavator. It describes 27 steps to assemble internal components like seals, springs, and bearings. These components include pistons, a cam plate, and a rotating assembly. The final steps connect the travel motor to the final drive and install exterior covers. Proper assembly requires using the correct tools and lubricants, and ensuring parts are aligned and torques are set correctly.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to disassemble the pump by removing components like bolts, sensors, valves, springs, pistons, gears, and bearings. The assembly section lists 48 steps to reinstall these components in reverse order, noting the need to heat some bearings before installation and ensure proper placement of pins, seals, and other parts. Precautions are provided for releasing spring forces. Required tools include various pliers, pins, and links to aid in removal and installation of components.
Caterpillar Cat 330F and 330F L Excavator (Prefix GHT) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling a 330F excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, brake piston, rotating assembly, pistons, seals, and other parts. Tools required include retaining ring pliers, a bearing puller, bolts, threaded rods, and other hardware. Safety precautions are provided to release spring forces carefully.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling the travel motor on a 336D2L excavator. It describes 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, springs, seals, relief valves, plugs, and more. Precautions are provided to watch for spring forces and contain fluids. Tools needed include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Reassembly will follow the disassembly steps in reverse order.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and over 15 additional parts. The goal is to allow maintenance and repair of these core powertrain systems.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 336D L Excavator (Prefix JBF) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for installing a unit injector sleeve on a Caterpillar C9 engine. It lists the required tools and gives step-by-step details for cleaning the sleeve and cylinder head bore, applying seals and retaining compound, and installing the sleeve using a hammer and installer tool. Proper installation is important to prevent leaks that could cause low pressure or excess oil consumption.
Caterpillar Cat 926 and 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing the cylinder head assembly on a 3204 vehicular engine. It describes:
1) Removing the cylinder head assembly by loosening hoses, removing bolts, and lifting it off with a hoist.
2) Cleaning and installing a new gasket before lowering the cylinder head back onto the cylinder block and tightening bolts in a specific sequence and torque.
3) Checking the flatness of the cylinder head and block surfaces during installation.
This document provides instructions for disassembling and assembling the torque converter and transmission of a Caterpillar 938F wheel loader. It details removing over 40 individual parts in 21 steps to disassemble the torque converter. A further 44 steps describe disassembling the transmission by removing components like shafts, gears, seals, and clutches. Precise tools and lifting devices are specified to carefully remove heavy parts. Reassembly is outlined in reverse order with notes to check components for wear and replace as needed.
Caterpillar Cat 325C and 325C L Excavator (Prefix BKW) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs to clean all parts thoroughly, apply lubricants, and install the parts in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Tools required include a transmission repair stand, link brackets, retaining ring pliers, and other specialized tools.
This document provides instructions for disassembling and assembling the piston pump of a 623G wheel scraper. Some key steps include:
1. Marking all mating components for alignment during assembly.
2. Removing various seals, springs, spools, and other internal parts from the pump housing and head.
3. Checking the preload on bearings during assembly by measuring clearance between the pump head and housing.
4. Cleaning all parts thoroughly before assembly and applying a light oil film. Precise alignment of marked components is important.
This document provides instructions for disassembling and assembling axle shaft assemblies for a 938F wheel loader. It describes removing components like the axle housing groups, axle shaft assembly, planetary carrier assembly, and installing new components in reverse order. Key steps include using various tools to remove retaining rings, planetary gears, and installing new bearings and seals at specified temperatures while ensuring proper torque specifications are met.
The document provides instructions for removing and installing fuel injection pumps on a Caterpillar 3406C diesel engine. Key steps include using various tools to hold components in place, loosening and removing bushings, seals and pumps. Reinstallation involves aligning pins and slots, installing spacers and seals correctly, and checking rack travel measurements to ensure proper installation. The document also describes disassembling and assembling the fuel injection pumps and fuel injection pump housing.
The document provides step-by-step instructions for disassembling and assembling the final drives of a 350L excavator. Key steps include removing the final drives and travel motors, disassembling the internal components of the final drives which include multiple planetary gear sets, carriers, and a sun gear, and then reassembling the final drives in reverse order. Proper cleaning, application of lubricants, and torque specifications are noted throughout to ensure correct reassembly.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, brake piston, rotating group, and seals. The instructions describe taking identifying marks on parts and cleaning components to prevent contamination. Reassembly is done in reverse order.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
1. Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR
Model: 621H WHEEL TRACTOR HKK
Configuration: 621H OEM Wheel Tractor HKK00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
621H, 623H and 627H Wheel Tractor-Scrapers Power Train
Media Number -KENR8883-02 Publication Date -01/06/2013 Date Updated -01/07/2013
i04496349
Torque Converter - Disassemble - Tractor
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8312 Retaining Ring Pliers 1
B 1P-0510 Driver Group 1
C 6L-7283 Bolts 2
Start By:
a. Remove the torque converter.
Illustration 1 g01052899
1/7(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
2. 1. Use Tooling (A) in order to remove retaining ring (1) from carriage support assembly (2).
Remove carriage support assembly (2) from hub (3). Use Tooling (B) and a suitable press in
order to remove the sleeve bearing from carriage support assembly (2).
Illustration 2 g00525303
2. Remove bolts (4) and the washers from torque converter impeller (5). Remove bolts (6), the
washers, and clamp plate (7) from impeller hub (8).
Illustration 3 g00525304
3. Install Tooling (C) in torque converter impeller (5). Use Tooling in order to remove torque
converter impeller (5) and impeller hub (8) from housing (9).
2/7(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 4 g00525305
4. Remove metal seal ring (10) from torque converter impeller (5). Remove impeller hub (8)
from torque converter impeller (5).
Illustration 5 g00525306
5. Remove thrust bearing (11) from carrier assembly (12).
Illustration 6 g00525308
Illustration 7 g00525309
6. Remove carrier assembly (12) and torque converter stator (13) as a unit from housing (9).
3/7(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 7. Position carrier assembly (12) and torque converter stator (13), as shown. Use Tooling (A)
in order to remove retaining ring (14) from torque converter stator (13). Remove thrust race
(15) from torque converter stator (13).
Illustration 8 g00525863
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove freewheel rollers (16) and freewheel springs (17) from freewheel cam (18).
Remove torque converter stator (13) from carrier assembly (12).
Illustration 9 g01080684
9. Use Tooling (A) in order to remove retaining ring (19) from torque converter stator (13).
Remove side plate (20) from torque converter stator (13).
4/7(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 10. Use Tooling (B) and a suitable press in order to remove freewheel cam (18) (not shown)
from torque converter stator (13).
Illustration 10 g01052916
11. Remove thrust bearing (21) from carrier assembly (12). Remove sleeve bearing (22) from
carrier assembly (12).
Illustration 11 g00525315
12. Remove torque converter turbine (23) and hub (3) as a unit from housing (9).
Illustration 12 g01052922
5/7(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. 13. Remove thrust bearing (24) and thrust race (25) from hub (3).
Illustration 13 g00525320
14. Position torque converter turbine (23), as shown. Remove thrust race (26) from hub (3). Put
an alignment mark on torque converter turbine (23) and hub (3) for installation purposes.
Remove bolts (27) from torque converter turbine (23).
Illustration 14 g00525321
15. Remove clamp ring (28) and torque converter turbine (23) from hub (3).
Illustration 15 g00525322
6/7(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 16. Remove thrust bearing (29) and thrust race (30) from housing (9).
Illustration 16 g00528612
17. Remove bolts (31) and flange (32) from housing (9).
Illustration 17 g00525323
18. Remove sleeve bearing (33) from flange (32).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Mar 27 07:09:34 UTC+0800 2021
7/7(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR
Model: 621H WHEEL TRACTOR HKK
Configuration: 621H OEM Wheel Tractor HKK00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
621H, 623H and 627H Wheel Tractor-Scrapers Power Train
Media Number -KENR8883-02 Publication Date -01/06/2013 Date Updated -01/07/2013
i07459845
Torque Converter - Assemble - Tractor
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8312 Retaining Ring Pliers 1
B 1P-0510 Driver Group 1
D 8T-5096 Dial Indicator Group 1
Illustration 1 g00528674
1. Use Tooling (B) and a suitable press to install sleeve bearing (33). Install sleeve bearing
(33) to flange (32).
1/8(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 2 g00528612
2. Install bolts (31) and flange (32) to housing (9). Tighten bolts (31) to a torque of
120 ± 15 N.m (89 ± 11 lb ft).
Illustration 3 g00525322
3. Install thrust race (30) and thrust bearing (29) to housing (9).
Illustration 4 g00525321
4. Install torque converter turbine (23) and clamp ring (28) to hub (3).
2/8(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 5 g06329533
5. Install bolts (27) to torque converter turbine (23). Tighten bolts (27) to a torque of
50 ± 7 N.m (37 ± 5 lb ft).
Illustration 6 g01052922
6. Install thrust race (25) and thrust bearing (24) to hub (3).
Illustration 7 g06329534
7. Install thrust race (26) to hub (3).
3/8(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 8 g00525315
8. Install torque converter turbine (23) and hub (3) as a unit to housing (9).
Illustration 9 g00528953
9. Use Tooling (B) and a suitable press to install sleeve bearing (22). Install sleeve bearing
(22) to carrier assembly (12).
10. Install thrust bearing (21) to carrier assembly (12).
Illustration 10 g01052912
4/8(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. 11. Install side plate (20) to torque converter stator (13). Use Tooling (A) to install retaining
ring (19). Install retaining ring (19) to torque converter stator (13).
Illustration 11 g00525863
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Use Tooling (B) and a suitable press to install freewheel cam (18). Install freewheel cam
(18) to torque converter stator (13).
13. Install torque converter stator (13) to carrier assembly (12). Install freewheel springs (17)
and freewheel rollers (16) to freewheel cam (18). Always install new freewheel springs (17)
and freewheel rollers (16). Install freewheel springs (17) with the maximum number of
loops in freewheel springs (17) to the outside of freewheel cam (18). Torque converter
stator (13) should turn freely in the counterclockwise direction. Torque converter stator (13)
should not turn freely in the clockwise direction.
5/8(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 12 g00525309
14. Install thrust race (15) to torque converter stator (13). Use Tooling (A) to install retaining
ring (14). Install retaining ring (14) to torque converter stator (13).
Illustration 13 g00525308
15. Install carrier assembly (12) and torque converter stator (13) as a unit to housing (9).
Illustration 14 g00525306
16. Install thrust bearing (11) to carrier assembly (12).
6/8(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 15 g00525305
17. Install impeller hub (8) to torque converter impeller (5). Install metal seal ring (10) to torque
converter impeller (5).
Illustration 16 g00525303
18. Install clamp plate (7), the washers, and bolts (6) to impeller hub (8). Tighten bolts (6) to a
torque of 50 ± 7 N.m (37 ± 5 lb ft).
19. Install bolts (4) and the washers to torque converter impeller (5). Tighten bolts (4) to a
torque of 50 ± 7 N.m (37 ± 5 lb ft).
Illustration 17 g00525299
20. Use Tooling (B) and a suitable press to install the sleeve bearing in carriage support
assembly (2). Install the sleeve bearing until the sleeve bearing is flush with the outside
machined surface of carriage support assembly (2).
21. Install carriage support assembly (2) to hub (3). Use Tooling (A) to install retaining ring (1).
Install retaining ring (1) to carriage support assembly (2).
7/8(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 18 g01053220
22. Install Tooling (D) to the torque converter, as shown. The edge of Tooling (D) must be in
contact with the edge of carrier assembly (12), as shown. Move hub (3) up and down with a
screwdriver. The end play of hub (3) must be 0.13 to 1.96 mm (0.005 to 0.077 inch).
End By:
a. Install the torque converter.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Mar 27 07:10:30 UTC+0800 2021
8/8(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR
Model: 621H WHEEL TRACTOR HKK
Configuration: 621H OEM Wheel Tractor HKK00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
621H, 623H and 627H Wheel Tractor-Scrapers Power Train
Media Number -KENR8883-02 Publication Date -01/06/2013 Date Updated -01/07/2013
i04573776
Transfer Gears - Remove and Install - Tractor, Off Chassis
SMCS - 3159-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B 308-3471 Jack Stand Gp 1
Start By:
a. Remove the transmission, torque converter, and transfer gears.
b. Remove the speed sensor.
1/3(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 1 g02731531
1. Use Tooling (A) and a suitable lifting device to position transmission, torque converter, and
transfer gears (1) onto suitable cribbing and Tooling (B). The weight of transmission, torque
converter, and transfer gears (1) is approximately 1320 kg (2910 lb).
Illustration 2 g02731558
2/3(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 3 g02731561
2. Attach Tooling (A) and a suitable lifting device to transfer gears (2). The weight of transfer
gears (2) is approximately 340 kg (750 lb). Remove nuts (3) and the bolts. Separate transfer
gears (2) from transmission (4). Remove O-ring seals (5).
Illustration 4 g02731564
3. Remove O-ring seal (6).
Installation Procedure
1. Install transfer gears (2) in the reverse order of removal.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Mar 27 07:11:26 UTC+0800 2021
3/3(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR
Model: 621H WHEEL TRACTOR HKK
Configuration: 621H OEM Wheel Tractor HKK00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
621H, 623H and 627H Wheel Tractor-Scrapers Power Train
Media Number -KENR8883-02 Publication Date -01/06/2013 Date Updated -01/07/2013
i04572074
Transfer Gears - Remove and Install - Tractor, In Chassis
SMCS - 3159-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 138-7574 Link Bracket 1
C - 1/2 - 13 NC by 1.5 inch Bolts 2
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact skin.
1. Start the machine. Turn the tractor so that the tractor is at a right angle to the scraper.
2. Remove the power train guard (transmission).
3. Remove the drive shaft.
4. Remove the speed sensor.
5. Remove gear pump (steering).
1/4(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 6. Remove piston pump (implement)
7. Remove the piston pump (elevator), if equipped.
8. Remove the transmission scavenge pump.
Illustration 1 g02731336
9. Disconnect clip (2) . Disconnect hose assemblies (3) and harness assembly (1) from filter
assembly (4).
10. Attach Tooling (A) and a suitable lifting device to filter assembly (4). The weight of filter
assembly (4) is approximately 36 kg (80 lb). Remove filter assembly (4).
Illustration 2 g02731337
11. Disconnect hose assemblies (5).
12. Remove hose assembly (8) and (11).
13. Remove tube assemblies (7) and (9).
14. Disconnect harness assembly (10) from transfer gears (6).
2/4(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 3 g02731365
15. Remove tube assembly (12).
Illustration 4 g02731366
Illustration 5 g02731367
16. Attach Tooling (A) and a suitable lifting device to transfer gears (6). The weight of transfer
gears (6) is approximately 318 kg (700 lb).
17. Remove bracket (14).
3/4(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. 18. Remove nuts (13) and the bolts that secure transfer gears (6) to the transmission case. Use
Tooling (C) to remove transfer gears (6). Remove transfer gears (6).
Illustration 6 g02731368
19. Remove O-ring seals (15).
Illustration 7 g02731369
20. Remove O-ring seal (16).
Installation Procedure
1. Install transfer gears (6) in the reverse order of removal.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Mar 27 07:12:22 UTC+0800 2021
4/4(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR
Model: 621H WHEEL TRACTOR HKK
Configuration: 621H OEM Wheel Tractor HKK00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
621H, 623H and 627H Wheel Tractor-Scrapers Power Train
Media Number -KENR8883-02 Publication Date -01/06/2013 Date Updated -01/07/2013
i07460047
Transfer Gears - Disassemble - Tractor
SMCS - 3159-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Bracket As 1
B
8B-7548 Push-Puller Tool Gp 1
8B-7551 Bearing Puller Gp 1
1P-0498 Drive Plate 1
C
5P-4170 Step Plate 1
1P-2321 Combination Puller 1
D
8B-7554 Bearing Cup Puller Gp 1
5P-4170 Step Plate 1
1P-0518 Drive Plate 1
E
8B-7560 Step Plate 1
5F-7345 Screw 1
8B-7554 Bearing Cup Puller Gp 1
F -
Bolts
3/8" - 16 NC by 3 inch
3
Start By:
1/10(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. a. Remove the transfer gear case.
b. Remove the transmission oil filter base.
c. Remove the transmission scavenge pump.
d. Remove the transmission oil pump.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
1. Put identification marks on components for installation purposes.
Illustration 1 g02603076
2. Remove the bolts that secure bearing cage (1) to the transfer gear case. Use Tooling (F) to
separate bearing cage (1) from the transfer gear case.
3. Remove bearing cage (1) and shims (2) from the transfer gear case.
2/10(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 2 g02602859
4. Remove the bolts that secure bearing cage (3) to the transfer gear case. Use Tooling (F) to
separate bearing cage (3) from the transfer gear case.
5. Remove bearing cage (3) and shims (4) from the transfer gear case.
Illustration 3 g02603657
6. Remove gear assembly (5).
Illustration 4 g02603659
7. Remove tube (6) and gear assembly (7).
3/10(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 5 g02602876
8. Remove bearing cups (8) from the transfer gear case. Attach Tooling (A) and a suitable
lifting device onto the transfer gear case. The weight of the transfer gear case is
approximately 340 kg (750 lb). Turn over the transfer gear case. Remove Tooling (A).
Illustration 6 g01102873
9. Remove the bolts that secure bearing cage (9) to the transfer gear case. Use Tooling (F) to
separate bearing cage (9) from the transfer gear case.
10. Remove bearing cage (9), shims (10), and gear (11) from the transfer gear case.
Illustration 7 g00529214
4/10(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. 11. Remove bearing cup (12) from the transfer gear case. Attach Tooling (A) and a suitable
lifting device onto the transfer gear case. Turn over the transfer gear case.
Illustration 8 g00529215
12. Remove bolts (13) that secure bearing cage (14) to the transfer gear case. If necessary, rotate
the gear until the three threaded holes are visible in bearing cage (14). Install Tooling (F)
through gear (15) and into bearing cage (14). Tighten Tooling (F) evenly until bearing cage
(14) and gear (15) separate from the transfer gear case. Remove bearing cage (14) and gear
(15) as a unit from the transfer gear case.
Illustration 9 g00529216
Illustration 10 g00529257
5/10(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. 13. Remove retaining ring (16) from gear (15). Remove bearing (17) and bearing cage (14)
from gear (15).
Illustration 11 g01048544
14. Remove bearing (17) from bearing cage (14).
Illustration 12 g01048548
15. Remove bolts (19) and separate gear (20) from gear (11). Use Tooling (B) to remove
bearing cone (18). Remove bearing cone (18) from gear (11). Repeat the procedure for the
bearing cone on the opposite side of gear (11).
Illustration 13 g02660644
6/10(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. 16. Use Tooling (C) to remove bearing cone (21). Remove bearing cone (21) from gear (5).
Repeat the procedure for the bearing cone on the opposite side of gear (5).
Illustration 14 g02661176
17. Use Tooling (C) to remove bearing cone (21). Remove bearing cone (21) from gear (7).
Repeat the procedure for the bearing cone on the opposite side of gear (7).
Illustration 15 g02661799
18. Use Tooling (D) to remove bearing cup (23). Remove bearing cup (23) from bearing cage
(1). Remove O-ring seal (24) from bearing cage (1).
Illustration 16 g01048553
7/10(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
30. 19. Remove bearing cup (25) from bearing cage (9).
Illustration 17 g02662017
20. Use Tooling (E) to remove bearing cup (26). Remove bearing cup (26) from bearing cage
(3). Remove O-ring seal (27) from bearing cage (3).
Illustration 18 g02603736
21. Remove the bolt that secure cover (28). Use Tooling (F) to remove cover (28). Remove
cover (28).
Illustration 19 g02603807
8/10(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
31. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
32. 22. Remove the bolt that secure bearing cage (29). Use Tooling (F) to remove bearing cage (29)
and shims (30). Remove bearing cage (29) and shims (30).
Illustration 20 g02603842
23. Remove tube (31) and gear assembly (32).
Illustration 21 g02662457
24. Use Tooling (C) to remove bearing cone (33). Remove bearing cone (33) from gear (32).
Repeat the procedure for the bearing cone on the opposite side of gear (32).
Illustration 22 g02603857
9/10(W)
w
2021/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...