Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR03250-03741).pdf

Service Repair Manual
Model
438C BACKHOE LOADER

Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438C BACKHOE LOADER 2DR
Configuration: 438C Backhoe Loader Side shift, Parallel Lift 2DR03250-03741 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
416C, 426C, 428C, 436C AND 438C BACKHOE LOADERS MACHINE SYST
Media Number -SENR1209-02 Publication Date -01/10/2004 Date Updated -05/06/2012
SENR12090033
Air Conditioner Compressor Group
SMCS - 1802-010; 1802-015; 1802-016
Remove & Install Air Conditioner Compressor Group
Effective July 1, 1992 regulations prohibit the venting of any refrigerant
into the atmosphere. Refer to Caterpillar publication SENR5664 and
NEDG5065 for the proper procedure, equipment and tools to reclaim
refrigerant from any Caterpillar machine.
Always wear goggles when working on air conditioning systems. The
system is under pressure at all times, engine running or not. Escaping
refrigerant R-134A can cause freezing of human flesh.
Do Not smoke while working on air conditioning systems. INHALING
REFRIGERANT R-134A THROUGH ANY SMOKING MATERIAL,
ALTHOUGH NOT TOXIC OR FLAMMABLE, CAN GENERATE
LETHAL PHOSGENE GAS AND CAUSE VIOLENT ILLNESS OR
DEATH. ALSO HEAT MUST NEVER BE APPLIED TO A
CHARGED SYSTEM. See Air Conditioning And Heating Service
Manual, Form No. SENR5664, for more information on removal and
installation of lines and refrigerant from the system.
1/12
438C Backhoe Loader Side shift, Parallel Lift 2DR03250-03741 (MACHINE) POWE...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

NOTE: For purging and charging the air conditioning system, refer to the Air Conditioning And
Heating Service Manual SENR5664.
1. Disconnect wiring harness (1).
2. Loosen nuts (2).
3. Position fan belt for compressor removal.
4. Disconnect the refrigerant lines.
5. Remove two bolts (3).
6. Remove compressor (4).
NOTE: For installation of the air conditioner compressor group, reverse the removal steps.
Remove & Install Air Conditioner Compressor Group (416C)
2/12
2019/10/11

2. Loosen nuts (1).
3. Position fan belt for compressor removal.
4. Disconnect refrigerant lines (2).
5. Remove two bolts (1).
6. Remove compressor (4).
7. Install air conditioner compressor group in the reverse order of removal.
Disassemble Air Conditioner Compressor
3/12
2019/10/11

Start By:
a. remove air conditioner compressor
1. Put the compressor assembly in position on Tool (A). Remove screws (1) to remove cover (2).
2. Use Tool (B), and remove nut and washer.
4/12
2019/10/11

3. Use Tool (C) and remove clutch front plate (3).
4. Remove key (4), shims (6) and cover (5).
5. Use a pair of retaining pliers, and remove felt ring and retainer assembly (7).
6. Remove retainer ring (8).
5/12
2019/10/11

7. Use Tool (D) and remove the shaft seal seat.
8. Remove O-ring seal (9).
9. Use Tool (E) and remove seal assembly from the shaft.
10. Remove retainer rings (10) and (11).
11. Use Tool (F) to remove pulley (12).
6/12
2019/10/11

12. Use a press, and remove bearing (13) from the pulley.
13. Remove felt ring (14). Remove retainer ring (15). Remove wire clip (16) and the field coil.
14. Remove bolts (18). Remove head (19) and valve plate (20). Remove and inspect gaskets (17).
7/12
2019/10/11

Assemble Air Conditioner Compressor
1. Put clean refrigerant oil on gaskets (1). Install a new gasket on head (2) and valve plate (3).
2. Install valve plate and head on the compressor body with the bolts that hold it.
3. Tighten the bolts to a torque of 30 to 34 N·m (22 to 25 lb) in the number sequence shown.
8/12
2019/10/11

4. Put field coil (6) in position on compressor body. Install clip (5) that holds wiring.
5. Install retainer ring (4). Install felt ring (7).
6. Install bearing in the pulley with Tool (A).
7. Use Tool (A) and drive the pulley and bearing assembly on the compressor body.
8. Install retainer rings (8) and (9).
9/12
2019/10/11

9. Put Tool (B) in position on the shaft. Put clean refrigerant oil on seal assembly (20). Use Tool
(C), and install seal assembly.
10. Release the seal assembly from Tool (C) by pushing downward and rotating Tool (C)
counterclockwise.
11. Install O-ring seal (21).
12. Put clean refrigerant oil on shaft seal seat (22). Install shaft seal seat (22) with Tool (D).
13. Install retainer ring (23).
10/12
438C Backhoe Loader Side shift, Parallel Lift 2DR03250-03741 (MACHINE) POW...
2019/10/11

14. Install felt ring and retainer assembly (24).
15. Install the original shims (26). Install cover (25) and key (27).
16. Install clutch front plate (28). Install Tool (F).
17. Carefully tap the clutch plate until it bottoms out against the shims.
18. Use Tool (E) to hold clutch front plate. Install a washer and nut. Tighten the nut to a torque of
34 to 40 N·m (25 to 30 lb ft).
11/12
2019/10/11

19. Check the gap between the clutch front plate. The gap should be 0.41 to 0.79 mm (.016 to .031
in). If the gap is not consistent around the circumference, lightly pry up at the minimum
variations. Lightly tap down at points of maximum variations.
20. If the gap is not correct again, add or subtract shims; then repeat Steps 16 through 19.
21. Install cover (29) with the screws that hold it.
End By:
a. install air conditioner compressor
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 11 08:28:00 UTC+0800 2019
12/12
2019/10/11

Shutdown SIS
Previous Screen
SENR12090034
Air Conditioner Filter
SMCS - 7342-010
Remove & Install Air Conditioner Filter (416C)
1. Loosen screws (2) and let cover (1) swing down.
2. Remove air conditioner filter (3) and replace.
3. Install in the reverse order of removal.
Fri Oct 11 08:28:55 UTC+0800 2019
1/1
2019/10/11

Shutdown SIS
Previous Screen
SENR12090035
Air Conditioner
SMCS - 1802-010
Remove & Install Air Conditioner (416C)
1/3
2019/10/11

1. Remove screws (1) and remove air vents (3).
2. Loosen three screws behind vents (hidden) and remove retaining plate (hidden) and rear duct
(2).
3. Repeat Steps 1 and 2 for left side of cab.
4. Remove side trim held by Velcro fasteners (4) (one side only).
5. Remove two screws and radio mount (5).
6. Remove two screws and disconnect wiring harnesses from control panel (6).
7. Loosen two screws (7) and remove air conditioning filter (hidden).
8. Remove headliner (8).
2/3
2019/10/11

9. Disconnect refrigerant lines (9).
11. Remove bolts (11) and remove air conditioner (12).
12. Install in the reverse order of removal.
Fri Oct 11 08:29:51 UTC+0800 2019
3/3
2019/10/11

Shutdown SIS
Previous Screen
SENR12090036
Cab
SMCS - 7301-010
Remove & Install Cab
Start By:
a. remove rear wheels
Fluid Spillage Containment
Care must be taken to ensure that fluids are contained during performance of inspection,
maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with
suitable containers before opening any compartment or disassembling any component containing
fluids. Refer to "Tools And Shop Products Guide", NENG2500 for tools and supplies suitable to
collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and
mandates.
At operating temperature, the hydraulic oil tank is hot and under
pressure. Hot oil can cause burns. Remove the breather filter cap only
when the engine is stopped and the breather filter cap is cool enough to
touch. Slowly loosen the breather filter cap to release any pressure in
1/5
2019/10/11

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

the hydraulic tank. Be cautious of hot hydraulic oil when any lines are
disconnected in the hydraulic system.
NOTE: Put identification on all lines, hoses, wires and tubes for installation purposes. Cap and plug
all lines, hoses and tubes to prevent foreign material from entering the system.
NOTE: Drain all fluids in a suitable container for storage or disposal.
1. Attach Tool (A) to each end of Tool (C). Attach straps to Tool (B).
2. Adjust Tool (C) so the cab can be picked up level.
3. Remove three wires (2) from starter (1).
4. Remove the seat, and all floor plates.
5. Disconnect linkage (3).
2/5
2019/10/11

6. Disconnect throttle linkage (4).
7. Disconnect all wiring connections (5).
8. Disconnect five hoses (6) from steering valve (7).
9. Disconnect hoses (8) and (9).
10. Disconnect two heater hoses (10).
3/5
2019/10/11

11. Remove retaining clip (11).
12. Remove pin (12) and two bolts (13) and remove brake assembly.
13. Remove mounting nut (14) on each side of the cab.
14. Remove nuts and bolts from under two floor plugs (16) on each side of the cab.
15. Remove bolt under the floor plate, and disconnect shift linkage (15).
16. Remove retaining clip (17), and remove pin (18).
17. Remove nut (19) and remove boom lock assembly.
4/5
2019/10/11

17. Disconnect two windshield washer hoses and two electrical connections (20) and (21), near
brake fluid reservoir (22).
18. Adjust all lifting Tooling and raise slowly making sure all wiring connections have been
disconnected and remove cab.
NOTE: Install in reverse order of removal.
End By:
a. install rear wheels
NOTE: Refer to the Operation & Maintenance Manual for all fluid capacities and the proper filling
procedures.
Fri Oct 11 08:30:47 UTC+0800 2019
5/5
2019/10/11

Shutdown SIS
Previous Screen
SENR12090037
Counterweight
SMCS - 7056-010
Remove & Install Counterweight
1. Position Tool (A) under counterweight (1).
2. Remove four bolts (2) that hold the counterweight to the frame.
3. Remove counterweight (1). The weight of the counterweight is 268 kg (590 lb).
NOTE: Install in the reverse order.
Fri Oct 11 08:31:43 UTC+0800 2019
1/1
2019/10/11

Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR03250-03741).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR03250-03741).pdf

Similar to Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR03250-03741).pdf (11)

More from odkkskkdmdmd

More from odkkskkdmdmd (9)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR03250-03741).pdf