What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438D BACKHOE LOADER BPE
Configuration: 438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Power
Train
Media Number -RENR3578-12 Publication Date -01/04/2010 Date Updated -13/04/2010
i01381641
Transmission (Direct Drive) - Assemble
SMCS - 3030-016-DD; 3066-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 137-8102 Spring Compressor 1
B 1P-1859 Snap Ring Pliers 1
C 4C-3652 Spring Compressor 1
D 6V-2157 Link Bracket 1
E 8T-5096 Indicator 1
F 1U-5750 Engine Stand 1
Note: The transmission will be assembled in major components. The major components will then
be assembled.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Note: Apply a light film of clean transmission oil to all components before assembly.
Transmission case
1/14438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00729262
Note: Install the shims behind each bearing cup that was recorded on the disassembly
procedure.
1. Install bearing cups (60), (61), (62), (63), and (64) .
(Direct Drive) Input Shaft
Illustration 2 g00731364
1. Install the needle thrust bearings on the shafts. The open end of cups (1) must point away
from the bearings or gears that are contacted.
2/14438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00729745
2. Install the seals on piston (56) .
Illustration 4 g00729752
3. Install piston (56). Install the retainer and spring (55). Use tooling (A) and a suitable press
in order to compress spring (55). Use tooling (B) in order to install snap ring (54) .
Illustration 5 g00729210
3/14438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 4. Install clutch pack (53) and retainer (52) .
5. Repeat Steps 2 through 4 for the opposite end of the input shaft.
Illustration 6 g00729208
6. Install gear (51), needle bearing (50), and spacer (49). Use tooling (B) in order to install
snap ring (48) .
Illustration 7 g00729771
7. Heat bearing cone (57) to 135 °C (275 °F). Install bearing cone (57) .
8. Install the input shaft.
(Direct Drive) Reverse Shaft
4/14438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g00729785
1. Heat bearing cones (45) and (46) to 135 °C (275 °F). Install bearing cones (45) and (46) .
2. Install the reverse shaft.
(Direct Drive) Shaft
Illustration 9 g00729792
1. Heat bearing cones (45) and (46) to 135 °C (275 °F). Install bearing cones (45) and (46) .
2. Install the shaft.
(Direct Drive) Output Shaft (Rear)
5/14438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g00729806
1. Install gear (42) .
Illustration 11 g00729200
2. Install housing (41) and gear (40). Use tooling (B) in order to install snap ring (39) .
Illustration 12 g00729810
6/14438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 3. Install synchronizer (38). Install gear (37). Heat bearing cone (36) to 135 °C (275 °F).
Install bearing cone (36) .
Illustration 13 g00729198
4. Install synchronizer (35), spacer (34), and bearings (33) .
Illustration 14 g00729812
5. Install gear (31) and (32). Heat bearing cone (30) to 135 °C (275 °F). Install bearing cone
(30) .
6. Install the output shaft (rear) in the transmission.
7/14438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00729196
Illustration 16 g00729064
7. Install two gearshift rods (23) on shift forks (29). Install the gearshift rods in the
transmission. Install three balls (28), two springs (27), and O-ring (26). Install plug (25) .
Illustration 17 g00729062
8. Install screws (24) on each of the gearshift rods (23) .
8/14438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g00730110
2. Install piston (22), spring (19), and retainer (21) .
3. Use tooling (C) and a suitable press in order to compress spring (19). Use tooling (B) in
order to install snap ring (20) .
Illustration 21 g00728948
4. Install clutch pack (18) and retainer (17) .
Illustration 22 g00728945
5. Install thrust washer (16), needle bearing (15), spacer (14), and two roller bearings (13) .
10/14438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engin...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g00729892
6. Heat bearing cone (11) to 135 °C (275 °F). Install bearing cone (11) .
Illustration 24 g00729903
7. Heat bearing cone (10) to 135 °C (275 °F). Install bearing cone (10) .
Illustration 25 g00728940
8. Install front output shaft (9) .
11/14438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engin...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Final Assembly
Illustration 26 g00730114
Note: Clean the mating surfaces of case (7). Apply a continuous bead of 1U-8846 Sealant to
the mating surface of the case.
1. Attach tooling (D) to case (7). Attach a suitable lifting device to tooling (D). Use fourteen
bolts (8) in order to install case (7). The weight of case (7) is 42 kg (94 lb).
Illustration 27 g00730079
2. Install a bolt in the output shaft. The output shaft must be fully seated. Install tooling (E), as
shown. Zero tooling (E). Pry up on the bolt and record the reading on tooling (E). The
reading must be 0.03 mm (0.0012 inch) to 0.08 mm (0.0031 inch). Add or remove shims in
Step 1 in the Case Assembly Procedure in order to obtain the correct reading.
12/14438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engin...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 28 g00730086
3. Repeat Step 1 for the input shaft and the output shaft (front). Use the same tolerance for all
of the shafts. Remove the expansion plug in order to check the input shaft. Use a
screwdriver to pry up on the input shaft. Install a new 1H-9721 Expansion Plug .
Illustration 29 g00728906
4. Install yoke (4), washer (5), and bolt (6) .
Illustration 30 g00728902
13/14438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engin...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 5. Install plug (3) .
Illustration 31 g00728895
6. Install Implement pump drive shaft (2) in transmission (1) .
Illustration 32 g00730116
7. Remove transmission (1) from tooling (F) .
End By: Install the transmission. Refer to Disassembly and Assembly, "Transmission (Direct
Drive) - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 3 12:30:10 UTC+0800 2019
14/14438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engin...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438D BACKHOE LOADER BPE
Configuration: 438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Power
Train
Media Number -RENR3578-12 Publication Date -01/04/2010 Date Updated -13/04/2010
i01459029
Transmission (Direct Drive) - Install
SMCS - 3030-012-DD
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7640 Stand 2
8S-7611 Tube 2
8S-7615 Pin 2
B 1U-9760 Jack Stand 2
C 1U-7505 Transmisson Jack 1
D 1U-7558 Mounting Brackets 2
E FT-2535 Engine Support Bar Assembly 1
1/5438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g00762601
1. Attach tooling (D) to tooling (C) and transmission (10) in order to maintain a good balance.
Illustration 2 g00762359
2. Use tooling (C) in order to position transmission (10). The weight of transmission (10) is
185 kg (408 lb).
Illustration 3 g00762479
2/5438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 3. Install fourteen bolts (11) .
Illustration 4 g00762562
4. Slide rod assembly (9) on the transmission lever and tighten bolt (8) .
Illustration 5 g00762561
5. Connect three electrical connectors (7) .
3/5438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Illustration 9 g00760890
11. Remove tooling (B) from front axle (2) .
Illustration 10 g00760888
12. Remove tooling (A) from rear frame (1) .
13. Fill the transmission with oil. Refer to Operation and Maintenance, SEBU7398,
"Capacities" for the proper type and capacity of oil.
,
End By:
a. Install the piston pump. Refer to Disassembly and AssemblyRENR3585, "Piston Pump
(Implement and Steering) - Install".
b. Install the rear drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Rear) -
Remove and Install".
c. Install the front drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Front) -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 3 12:31:06 UTC+0800 2019
5/5438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438D BACKHOE LOADER BPE
Configuration: 438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Power
Train
Media Number -RENR3578-12 Publication Date -01/04/2010 Date Updated -13/04/2010
i05395070
Transmission (Power Shift) - Remove
SMCS - 3030-011-PM
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7640 Stand 2
8S-7611 Tube 2
8S-7615 Pin 2
B 1U-9760 Jack Stand 2
C 1U-7505 Transmisson Jack 1
D 1U-7558 Mounting Brackets 2
E FT-2535 Engine Support Bar Assembly 1
Start By:
A. Remove the front drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Front) -
Remove and Install".
B. Remove the rear drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Rear) -
Remove and Install".
C. Remove the piston pump. Refer to Disassembly and Assembly, RENR3585, "Piston Pump
(Implement and Steering) - Remove".
1. Use a suitable lifting device in order to raise the machine to a height of 91.4 mm (36 inch)
between the ground and the side step.
1/6438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g00760888
2. Place tooling (A) under rear frame (1) .
Illustration 2 g00760890
3. Place tooling (B) under front axle (2) .
2/6438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 3 g03410213
4. Remove the inspection cover. Install Tooling (E) in order to support the engine when the
transmission is removed.
Illustration 4 g00760891
5. Disconnect seven electrical connectors (3) . Cut three straps (4) .
Illustration 5 g00760892
6. Cut the strap and disconnect three electrical connectors (5) .
3/6438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine(...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...