This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 432F backhoe loader engine. The procedure involves using special tools to compress the valve springs, remove the keepers, and access the valves. Springs must be replaced in pairs and steps taken to ensure the piston is at top-center before removing springs. Cleaning and inspecting components is also described prior to reinstallation. The document contains illustrations and notices about safety and preventing contamination.
Caterpillar cat 432 f backhoe loader (prefix sej) service repair manual (sej0...ujfdjjskkemme
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 432F backhoe loader engine. The procedure involves using special tools to compress the valve springs, remove the keepers, and safely manipulate the valves and pistons. Proper cleaning and inspection of parts is emphasized. The installation process is essentially the reverse of removal, taking care to properly seat the valve keepers and avoid injury from the compressed springs.
Caterpillar cat 420 f backhoe loader (prefix lkh) service repair manual (lkh0...ufujjdjkskemme
This document provides instructions for removing and installing an exhaust elbow and inlet/exhaust valves on a Caterpillar 420F backhoe loader with a C4.4 engine. It outlines the required tools and safety notices, removal procedure with illustrations, and installation procedure. The procedures describe using turning tools to position pistons, a valve spring compressor to remove/install springs, and ensuring correct orientation and torque specifications for reinstallation.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using specialized tools to compress the valve springs, remove the valve keepers and other components, and extract the valves from the cylinder head. The installation procedure specifies cleaning and inspecting components, lubricating the valve stems, and using tools to compress springs and insert new components in the reverse order of removal. Safety precautions are provided regarding the force of compressed springs. A separate section then details removing and installing the engine oil filter base.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...fkjsekksmem
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
Caterpillar cat 314 e cr excavator (prefix ycw) service repair manual (ycw000...jfdskekdmme
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning parts and installing the oil cooler assembly with new gaskets and bolts. Tools, safety precautions, and maintenance tips are also provided.
Caterpillar cat 434 f backhoe loader (prefix mtr) service repair manual (mtr0...uuudfjjfjkkskm
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. It outlines the required tools and parts, safety considerations, and step-by-step procedures. The removal process involves using a valve spring compressor tool to decompress the springs and remove the keepers and springs. The installation process reverses this, compressing the springs to insert the keepers. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed, springs and retainers are compressed with the tool and keepers are fitted. The engine oil filter base and engine oil cooler are also removed and installed, following steps to drain fluids, remove bolts and gaskets, and clean components.
Caterpillar cat 249 d compact track loader (prefix ah9) service repair manual...fusjezsfkskefmsme
This document provides instructions for removing and installing exhaust manifolds, inlet and exhaust valves, and inlet and exhaust valve springs on Caterpillar C1.1, C1.5, and C2.2 engines. The procedures describe using various tools to compress springs, remove and install components like manifolds, valves, seals, and keepers, while taking precautions to prevent damage and entry of loose parts into the engine. Detailed illustrations supplement the text instructions.
Caterpillar cat 432 f backhoe loader (prefix sej) service repair manual (sej0...ujfdjjskkemme
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 432F backhoe loader engine. The procedure involves using special tools to compress the valve springs, remove the keepers, and safely manipulate the valves and pistons. Proper cleaning and inspection of parts is emphasized. The installation process is essentially the reverse of removal, taking care to properly seat the valve keepers and avoid injury from the compressed springs.
Caterpillar cat 420 f backhoe loader (prefix lkh) service repair manual (lkh0...ufujjdjkskemme
This document provides instructions for removing and installing an exhaust elbow and inlet/exhaust valves on a Caterpillar 420F backhoe loader with a C4.4 engine. It outlines the required tools and safety notices, removal procedure with illustrations, and installation procedure. The procedures describe using turning tools to position pistons, a valve spring compressor to remove/install springs, and ensuring correct orientation and torque specifications for reinstallation.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using specialized tools to compress the valve springs, remove the valve keepers and other components, and extract the valves from the cylinder head. The installation procedure specifies cleaning and inspecting components, lubricating the valve stems, and using tools to compress springs and insert new components in the reverse order of removal. Safety precautions are provided regarding the force of compressed springs. A separate section then details removing and installing the engine oil filter base.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...fkjsekksmem
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
Caterpillar cat 314 e cr excavator (prefix ycw) service repair manual (ycw000...jfdskekdmme
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning parts and installing the oil cooler assembly with new gaskets and bolts. Tools, safety precautions, and maintenance tips are also provided.
Caterpillar cat 434 f backhoe loader (prefix mtr) service repair manual (mtr0...uuudfjjfjkkskm
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. It outlines the required tools and parts, safety considerations, and step-by-step procedures. The removal process involves using a valve spring compressor tool to decompress the springs and remove the keepers and springs. The installation process reverses this, compressing the springs to insert the keepers. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed, springs and retainers are compressed with the tool and keepers are fitted. The engine oil filter base and engine oil cooler are also removed and installed, following steps to drain fluids, remove bolts and gaskets, and clean components.
Caterpillar cat 249 d compact track loader (prefix ah9) service repair manual...fusjezsfkskefmsme
This document provides instructions for removing and installing exhaust manifolds, inlet and exhaust valves, and inlet and exhaust valve springs on Caterpillar C1.1, C1.5, and C2.2 engines. The procedures describe using various tools to compress springs, remove and install components like manifolds, valves, seals, and keepers, while taking precautions to prevent damage and entry of loose parts into the engine. Detailed illustrations supplement the text instructions.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using specialized tools to compress the valve springs, remove the valve keepers and other components, and extract the valves from the cylinder head. The installation procedure specifies cleaning and inspecting components, lubricating the valve stems, and using tools to compress springs and insert new components in the reverse order of removal. Safety precautions are provided regarding working with compressed springs. A separate section then details removing and installing the engine oil filter base.
This document provides instructions for removing and installing the engine oil cooler on a Caterpillar 416F2 backhoe loader with a C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning components, installing a new gasket, positioning the oil cooler assembly onto the engine block, and hand tightening mounting bolts while supporting the oil cooler.
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar 416F2 backhoe loader with a C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning components, installing a new gasket, positioning the oil cooler assembly onto the engine block, and hand tightening mounting bolts while supporting the oil cooler.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove the keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed on the guides, and the springs and keepers are compressed into place using the tool. The engine oil filter base and engine oil cooler are also removed and installed, following steps to drain fluids, remove bolts and gaskets, and clean components.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The procedure involves using specialized tools to compress the valve springs to remove and install valve keepers. Safety precautions are outlined to prevent injury from the force of compressed springs. Instructions are also given for removing and installing the engine oil filter base, which involves draining oil and replacing gaskets.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed on the guides, springs and retainers are compressed using the tool and keepers are installed. The engine oil filter base and engine oil cooler are also removed and installed, following cleaning and installation of new gaskets.
This document provides removal and installation instructions for the exhaust elbow and inlet/exhaust valves on a 420F Backhoe Loader with a C4.4 engine. The procedures describe using various tools to remove bolts, brackets, and springs before cleaning and inspecting parts and reinstalling them in the reverse order. Safety notices are included regarding wearing protective equipment when compressing springs and ensuring correct orientation of parts.
This document provides removal and installation instructions for the exhaust elbow and inlet/exhaust valves on a Caterpillar 420F backhoe loader with a C4.4 engine. The procedures describe removing bolts to remove the exhaust elbow and support bracket, cleaning and positioning the parts for installation, and tightening bolts to specifications. Valve spring removal and installation involves using tools to compress the springs, remove/install keepers, and rotate the crankshaft to position pistons while removing/installing parts in the correct order. Safety notices are included throughout regarding cleaning parts, wearing protective equipment when working with springs, and ensuring proper assembly.
This document provides instructions for removing and installing an exhaust elbow and inlet/exhaust valves on a Caterpillar 420F backhoe loader. It describes the required tools and gives step-by-step procedures for removing the exhaust elbow and removing/installing inlet and exhaust valve springs. Safety notices are included throughout regarding preventing contamination and injury from compressed springs.
This document provides removal and installation instructions for the exhaust elbow and inlet/exhaust valves on a Caterpillar 420F backhoe loader with a C4.4 engine. The procedures describe removing bolts to remove the exhaust elbow and support bracket, cleaning and positioning the parts for installation, and tightening bolts to specifications. Valve spring removal and installation involves using tools to compress the springs, remove/install keepers, and rotate the crankshaft to position pistons while removing/installing parts in the correct order. Safety notices are included throughout regarding cleaning parts, wearing protective equipment when working with springs, and ensuring proper assembly.
Caterpillar cat 420 f backhoe loader (prefix lkh) service repair manual (lkh0...fjsjekkdmme
This document provides instructions for removing and installing an exhaust elbow on a 420F Backhoe Loader with a C4.4 engine. It describes removing 4 bolts and the elbow, then 5 bolts and a support bracket. For installation, it instructs to clean and position the support bracket and elbow, then install the bolts and tighten to 44 N·m. It also provides procedures for removing and installing inlet and exhaust valve springs, including using special tools to compress the springs at specific piston positions.
Caterpillar cat 420 f backhoe loader (prefix lkh) service repair manual (lkh0...fujskeksmemqa
This document provides instructions for removing and installing an exhaust elbow and inlet/exhaust valves on a Caterpillar 420F backhoe loader with a C4.4 engine. It outlines the required tools and safety notices, removal procedure with illustrations, and installation procedure. The procedures describe using turning tools to position pistons, a valve spring compressor to remove/install springs, and ensuring correct installation of keepers and seals.
This document provides instructions for removing and installing an exhaust elbow on a 420F Backhoe Loader with a C4.4 engine. The removal procedure involves removing 4 bolts and the exhaust elbow, then removing 5 bolts and a support bracket. For installation, the support bracket is reinstalled with 5 bolts tightened to 44 N·m, then the exhaust elbow is positioned and secured with 4 bolts also tightened to 44 N·m. Precautions are provided to ensure correct orientation and cleaning of parts.
This document provides instructions for removing and installing an exhaust elbow on a Caterpillar 420F backhoe loader. The removal procedure involves removing four bolts to detach the elbow and five bolts to remove the support bracket. For installation, the support bracket is reattached with five bolts and the elbow is positioned correctly and secured with four bolts. Torque specifications for all bolts are provided.
This document provides instructions for removing and installing an exhaust elbow on a Caterpillar 420F backhoe loader. The removal procedure involves removing four bolts to detach the elbow and five bolts to remove the support bracket. For installation, the support bracket is reattached with five bolts and the elbow is positioned correctly and secured with four bolts. Torque specifications for all bolts are provided.
Caterpillar Cat 320D2 L Excavator (Prefix RAR) Service Repair Manual Instant ...jkdkkdsmmd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C7.1 engine. It describes the required tools and outlines a multi-step process that involves positioning the piston at top dead center, compressing the valve spring with a tool to remove keepers and the spring, and reversing the process to install new springs. Safety notices are provided to wear protective equipment when working with compressed springs.
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C7.1 engine. It outlines the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring while the piston is at top dead center, allowing removal of the valve keepers and spring. Installation follows the reverse process. Inspection and cleaning of valve components is also specified.
Caterpillar cat 390 f l excavator (prefix hng) service repair manual (hng0000...fjskefksemer
This document provides instructions for removing and installing the front gear group on a C18 engine. The removal procedure involves taking off 14 parts including plates, gears, and seals. The installation procedure describes cleaning components and applying thread lock before reinstalling the 20 parts in reverse order while adjusting backlash as specified. Proper timing of the gears is critical to avoid engine damage.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjskefksemer
The document provides instructions for disassembling and assembling the travel motor on a 390F excavator. It describes 40 steps to disassemble the travel motor by removing components like the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 17 steps for reassembling the travel motor by reversing the disassembly process and ensuring proper installation of alignment marks and seals. Precision cleaning and installation of parts is emphasized.
Caterpillar cat 374 f l excavator (prefix mfl) service repair manual (mfl0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. It lists the required tools and presents a step-by-step process to remove and install components such as the ring gear, carrier assemblies, gears, shafts, seals, bearings and housings. The procedure involves using lifting devices, pins, bolts and other fasteners to separate parts and reassemble the final drive. Weights of removed parts are provided to aid in lifting.
Caterpillar cat 374 f l excavator (prefix dnm) service repair manual (dnm0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. It lists the required tools and presents a step-by-step process to remove and install various components of the final drive such as the ring gear, carrier assemblies, sun gears, and housing components. Precautions are given to clean parts thoroughly, apply thread locking compounds, and verify that puller studs meet the capacity of any hydraulic cylinders used during the process.
More Related Content
Similar to Caterpillar cat 432 f backhoe loader (prefix sej) service repair manual (sej00001 and up)
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using specialized tools to compress the valve springs, remove the valve keepers and other components, and extract the valves from the cylinder head. The installation procedure specifies cleaning and inspecting components, lubricating the valve stems, and using tools to compress springs and insert new components in the reverse order of removal. Safety precautions are provided regarding working with compressed springs. A separate section then details removing and installing the engine oil filter base.
This document provides instructions for removing and installing the engine oil cooler on a Caterpillar 416F2 backhoe loader with a C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning components, installing a new gasket, positioning the oil cooler assembly onto the engine block, and hand tightening mounting bolts while supporting the oil cooler.
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar 416F2 backhoe loader with a C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning components, installing a new gasket, positioning the oil cooler assembly onto the engine block, and hand tightening mounting bolts while supporting the oil cooler.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove the keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed on the guides, and the springs and keepers are compressed into place using the tool. The engine oil filter base and engine oil cooler are also removed and installed, following steps to drain fluids, remove bolts and gaskets, and clean components.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The procedure involves using specialized tools to compress the valve springs to remove and install valve keepers. Safety precautions are outlined to prevent injury from the force of compressed springs. Instructions are also given for removing and installing the engine oil filter base, which involves draining oil and replacing gaskets.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed on the guides, springs and retainers are compressed using the tool and keepers are installed. The engine oil filter base and engine oil cooler are also removed and installed, following cleaning and installation of new gaskets.
This document provides removal and installation instructions for the exhaust elbow and inlet/exhaust valves on a 420F Backhoe Loader with a C4.4 engine. The procedures describe using various tools to remove bolts, brackets, and springs before cleaning and inspecting parts and reinstalling them in the reverse order. Safety notices are included regarding wearing protective equipment when compressing springs and ensuring correct orientation of parts.
This document provides removal and installation instructions for the exhaust elbow and inlet/exhaust valves on a Caterpillar 420F backhoe loader with a C4.4 engine. The procedures describe removing bolts to remove the exhaust elbow and support bracket, cleaning and positioning the parts for installation, and tightening bolts to specifications. Valve spring removal and installation involves using tools to compress the springs, remove/install keepers, and rotate the crankshaft to position pistons while removing/installing parts in the correct order. Safety notices are included throughout regarding cleaning parts, wearing protective equipment when working with springs, and ensuring proper assembly.
This document provides instructions for removing and installing an exhaust elbow and inlet/exhaust valves on a Caterpillar 420F backhoe loader. It describes the required tools and gives step-by-step procedures for removing the exhaust elbow and removing/installing inlet and exhaust valve springs. Safety notices are included throughout regarding preventing contamination and injury from compressed springs.
This document provides removal and installation instructions for the exhaust elbow and inlet/exhaust valves on a Caterpillar 420F backhoe loader with a C4.4 engine. The procedures describe removing bolts to remove the exhaust elbow and support bracket, cleaning and positioning the parts for installation, and tightening bolts to specifications. Valve spring removal and installation involves using tools to compress the springs, remove/install keepers, and rotate the crankshaft to position pistons while removing/installing parts in the correct order. Safety notices are included throughout regarding cleaning parts, wearing protective equipment when working with springs, and ensuring proper assembly.
Caterpillar cat 420 f backhoe loader (prefix lkh) service repair manual (lkh0...fjsjekkdmme
This document provides instructions for removing and installing an exhaust elbow on a 420F Backhoe Loader with a C4.4 engine. It describes removing 4 bolts and the elbow, then 5 bolts and a support bracket. For installation, it instructs to clean and position the support bracket and elbow, then install the bolts and tighten to 44 N·m. It also provides procedures for removing and installing inlet and exhaust valve springs, including using special tools to compress the springs at specific piston positions.
Caterpillar cat 420 f backhoe loader (prefix lkh) service repair manual (lkh0...fujskeksmemqa
This document provides instructions for removing and installing an exhaust elbow and inlet/exhaust valves on a Caterpillar 420F backhoe loader with a C4.4 engine. It outlines the required tools and safety notices, removal procedure with illustrations, and installation procedure. The procedures describe using turning tools to position pistons, a valve spring compressor to remove/install springs, and ensuring correct installation of keepers and seals.
This document provides instructions for removing and installing an exhaust elbow on a 420F Backhoe Loader with a C4.4 engine. The removal procedure involves removing 4 bolts and the exhaust elbow, then removing 5 bolts and a support bracket. For installation, the support bracket is reinstalled with 5 bolts tightened to 44 N·m, then the exhaust elbow is positioned and secured with 4 bolts also tightened to 44 N·m. Precautions are provided to ensure correct orientation and cleaning of parts.
This document provides instructions for removing and installing an exhaust elbow on a Caterpillar 420F backhoe loader. The removal procedure involves removing four bolts to detach the elbow and five bolts to remove the support bracket. For installation, the support bracket is reattached with five bolts and the elbow is positioned correctly and secured with four bolts. Torque specifications for all bolts are provided.
This document provides instructions for removing and installing an exhaust elbow on a Caterpillar 420F backhoe loader. The removal procedure involves removing four bolts to detach the elbow and five bolts to remove the support bracket. For installation, the support bracket is reattached with five bolts and the elbow is positioned correctly and secured with four bolts. Torque specifications for all bolts are provided.
Caterpillar Cat 320D2 L Excavator (Prefix RAR) Service Repair Manual Instant ...jkdkkdsmmd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C7.1 engine. It describes the required tools and outlines a multi-step process that involves positioning the piston at top dead center, compressing the valve spring with a tool to remove keepers and the spring, and reversing the process to install new springs. Safety notices are provided to wear protective equipment when working with compressed springs.
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C7.1 engine. It outlines the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring while the piston is at top dead center, allowing removal of the valve keepers and spring. Installation follows the reverse process. Inspection and cleaning of valve components is also specified.
Similar to Caterpillar cat 432 f backhoe loader (prefix sej) service repair manual (sej00001 and up) (17)
Caterpillar cat 390 f l excavator (prefix hng) service repair manual (hng0000...fjskefksemer
This document provides instructions for removing and installing the front gear group on a C18 engine. The removal procedure involves taking off 14 parts including plates, gears, and seals. The installation procedure describes cleaning components and applying thread lock before reinstalling the 20 parts in reverse order while adjusting backlash as specified. Proper timing of the gears is critical to avoid engine damage.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjskefksemer
The document provides instructions for disassembling and assembling the travel motor on a 390F excavator. It describes 40 steps to disassemble the travel motor by removing components like the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 17 steps for reassembling the travel motor by reversing the disassembly process and ensuring proper installation of alignment marks and seals. Precision cleaning and installation of parts is emphasized.
Caterpillar cat 374 f l excavator (prefix mfl) service repair manual (mfl0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. It lists the required tools and presents a step-by-step process to remove and install components such as the ring gear, carrier assemblies, gears, shafts, seals, bearings and housings. The procedure involves using lifting devices, pins, bolts and other fasteners to separate parts and reassemble the final drive. Weights of removed parts are provided to aid in lifting.
Caterpillar cat 374 f l excavator (prefix dnm) service repair manual (dnm0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. It lists the required tools and presents a step-by-step process to remove and install various components of the final drive such as the ring gear, carrier assemblies, sun gears, and housing components. Precautions are given to clean parts thoroughly, apply thread locking compounds, and verify that puller studs meet the capacity of any hydraulic cylinders used during the process.
Caterpillar cat 374 f l excavator (prefix at2) service repair manual (at20000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists 37 steps for disassembly, which include removing the final drive cover, carrier assemblies, gears, shafts, seals and housings. It then lists 17 steps for assembly, which include cleaning parts, applying anti-seize compound, installing bearings, seals and housings, and attaching the main housing to the motor housing. Tools required include lifting devices, puller studs, torque wrenches and seal installers. Safety precautions are provided for using hydraulic cylinders and puller studs during assembly.
Caterpillar cat 374 f l excavator (prefix ap4) service repair manual (ap40000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. The disassembly process involves removing over 30 individual parts from the final drive housing. The assembly process specifies cleaning and lubricating parts, setting the bearing preload using shims, and installing components in reverse order of disassembly. Precautions are provided regarding tool selection and lubrication of seals during assembly.
Caterpillar cat 374 d l excavator (prefix pja) service repair manual (pja0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 374D L Excavator. It describes 34 steps to disassemble the final drive by removing components like the ring gear, carrier assemblies, gears, shafts and seals. It then describes 8 steps for assembling the final drive, which involves cleaning parts, applying threadlocker, installing bearings and housings, and determining the correct shim number based on measuring gear dimensions. The document contains diagrams to illustrate each step in the procedures.
Caterpillar cat 374 d l excavator (prefix pax) service repair manual (pax0000...fjskefksemer
This document provides instructions for disassembling and assembling components of a 374D L excavator travel motor and final drive system. The multi-step process includes removing 17 bolts and other hardware to disassemble the final drive cover and housing, exposing internal parts like pistons, seals, and gears. Proper tooling and safety precautions are emphasized to correctly handle springs, weights up to 817kg, and contained hydraulic fluids during disassembly and reassembly.
Caterpillar cat 365 c l hydraulic excavator (prefix par) service repair manua...fjskefksemer
This document provides instructions for disassembling and assembling the travel motor of a 365C excavator. The disassembly process involves 29 steps to remove components like springs, plates, pistons, seals, and bearings. The assembly process describes 31 steps and requires tools to reinstall these components in the reverse order and adjust shims to ensure proper clearance is achieved. Precautions are provided to wear protective equipment when working with spring loaded components.
Caterpillar cat 365 c l excavator (prefix mcy) service repair manual (mcy0000...fjskefksemer
1) The document provides assembly instructions for a 365C L excavator final drive. It describes 36 steps to assemble components like bearings, gears, seals, housings and covers.
2) Precise measurements and torque specifications are listed to ensure proper bearing preload and component attachment.
3) Special tools are required to lift heavy parts, apply sealant and torque fasteners correctly during reassembly.
Caterpillar cat 349 e l vg excavator (prefix kcn) service repair manual (kcn0...fjskefksemer
This document provides assembly instructions for the final drive of a 349E L-VG excavator. It includes specifications for parts, required tools, and a step-by-step procedure. The procedure involves installing bearings, seals, gears, shafts, washers, and bolts in the proper order and orientation. Precise measurements and torque specifications are provided to ensure correct assembly.
Caterpillar cat 385 c l excavator (prefix t2e) service repair manual (t2e0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists 33 steps for disassembly, removing components like the housing cover, carrier assemblies, planetary gears, and seals. It notes that cleanliness is important to prevent damage. The assembly section lists one step to reassemble the final drive on the repair stand and cribbing, referring to other sections for installing components like seals. Proper cleaning and inspection of parts is emphasized along with using new replacement parts if any are worn or damaged.
Caterpillar cat 374 f l excavator (prefix nfj) service repair manual (nfj0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and presents 37 steps to disassemble the various components of the final drive, including removing the ring gear, carrier assemblies, sun gears, and housing components. The assembly section lists 2 steps, including cleaning all parts and reassembling the final drive while applying anti-seize compound to bearing surfaces. Safety notes warn about ensuring puller studs meet hydraulic cylinder capacity when used.
Caterpillar cat 349 e l vg excavator (prefix dge) service repair manual (dge0...fjskefksemer
This document provides instructions for disassembling and assembling the final drive on a 349E L-VG excavator. It describes 33 steps to disassemble the final drive components including removing bolts, gears, shafts, and housings. It also lists 13 specifications for reassembly and describes 17 steps to reassemble the final drive, applying sealant and torqueing bolts to specification. The document includes illustrations to clarify each step of the process.
Caterpillar cat 385 c l excavator (prefix eda) service repair manual (eda0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and parts. The disassembly process involves removing over 30 components of the final drive including housing covers, gears, shafts, and seals. Photos illustrate each step. Cleanliness is emphasized to prevent damage to precision parts. The assembly section states to reassemble in reverse order and check seals for wear before installation.
Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and gives step-by-step details for removing components such as housing covers, gears, shafts, and seals. Cleanliness is emphasized throughout. The 34 steps describe taking the final drive apart piece by piece and include notes about weights of components and using lifting devices for heavy parts. Reassembly instructions are provided in the last step.
Caterpillar cat 390 f l excavator (prefix feh) service repair manual (feh0000...fjskefksemer
This document provides instructions for disassembling and assembling the travel motor on a 390F excavator model. It involves 40 steps to disassemble the various components of the travel motor including removing seals, springs, plates, pistons, and bearings. The assembly section outlines 31 steps to reinstall these components in reverse order while ensuring proper cleaning and alignment of parts. Precision tools are required and safety precautions mentioned to avoid injury from spring forces.
Caterpillar cat 345 c l hydraulic excavator (prefix tdg) service repair manua...fjskefksemer
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and housing pieces. It notes to mark parts locations and orientations. Reassembly follows the reverse order, and notes to clean parts and avoid damaging mating surfaces.
Caterpillar cat 345 c l hydraulic excavator (prefix lys) service repair manua...fjskefksemer
This document provides disassembly and assembly instructions for the final drive of a 345C L excavator. The final drive disassembly procedure involves 30 steps to remove components like the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure is not included in full but references using the required tools listed and applying thread lock, gasket sealant, and anti-seize compounds to correctly reassemble components.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 432F BACKHOE LOADER SEJ
Configuration: 432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763412
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B
9U-6195 Valve Spring Compressor 1
268-1969 Adapter 1
276-1221 Head 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Start By:
a. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove".
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
NOTICE
Keep all parts clean from contaminants.
1/6432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Contaminants may cause rapid wear and shortened component life.
Note: The following procedure should be adopted in order to remove the valve springs when the
cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install" for the procedure to remove the valve springs from a cylinder head
that has been removed from the engine.
Note: Ensure that the appropriate piston is at the top center position before the valve spring is
removed. Failure to ensure that the piston is at the top center position may allow the valve to drop
into the cylinder bore.
NOTICE
Plug the apertures for the push rods in the cylinder head in order to
prevent the entry of loose parts into the engine.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
1. Follow Steps 1.a through 1.d in order to position the appropriate piston at top center.
a. Install Tooling (B) in position on the cylinder head in order to compress a valve
spring for the appropriate piston.
b. Use Tooling (B) in order to compress valve spring (3) and open the valve slightly.
Note: Do not compress the spring so that valve spring retainer (2) touches the valve
stem seal.
2/6432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. c. Use Tooling (A) in order to rotate the crankshaft carefully, until the piston touches the
valve.
Note: Do not use excessive force to turn the crankshaft. The use of force can result in
bent valve stems.
d. Continue to rotate the crankshaft and gradually release the pressure on Tooling (B)
until the piston is at the top center position. The valve is now held in a position that
allows the valve spring to be safely removed.
NOTICE
Do not turn the crankshaft while the valve springs are removed.
Note: Valve springs must be replaced in pairs for the inlet valve or the exhaust valve of
each cylinder. If all valve springs require replacement the procedure can be carried out on
two cylinders at the same time. The procedure can be carried out on the following pairs of
cylinders. 1 with 4 and 2 with 3. Ensure that all of the valve springs are installed before
changing from one pair of cylinders to another pair of cylinders.
Illustration 1 g01343550
Typical example
3/6432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 2. Apply sufficient pressure to Tooling (B) in order to allow removal of valve keepers (1).
Remove valve keepers (1).
Note: Do not compress the spring so that valve spring retainer (2) touches the valve stem
seal.
3. Slowly release the pressure on Tooling (B).
4. Remove valve spring retainer (2) and remove valve spring (3).
5. If necessary, remove the valve stem seals.
6. Repeat Steps 2 through 5 in order to remove the remaining valve spring from the
appropriate cylinder.
7. Remove Tooling (B).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B
9U-6195 Valve Spring Compressor 1
268-1969 Adapter 1
276-1221 Head 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
4/6432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Do not turn the crankshaft while the valve springs are removed.
1. Inspect the valve springs for the correct length. Refer to Specifications, "Cylinder Head
Valves " for more information.
2. If necessary, install a new valve stem seal onto the valve guide.
Note: The outer face of the valve guide must be clean and dry before installing the valve
stem seal.
Illustration 2 g01343550
Typical example
3. Install valve spring (3) onto the cylinder head. Position valve spring retainer (2) onto valve
spring (3).
Improper assembly of parts that are spring loaded can cause bodily
injury.
5/6432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
4. Install Tooling (B) in the appropriate position on the cylinder head in order to compress the
valve spring.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
5. Apply sufficient pressure to Tooling (B) in order to install valve keepers (1). Install valve
spring keepers (1).
Note: Do not compress the spring so that valve spring retainer (2) touches the valve stem
seal .
6. Carefully release the pressure on Tooling (B).
Note: Ensure that the valve keepers are correctly seated.
7. Repeat Steps 2 to 6 for the remaining valves.
The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
8. Remove Tooling (B).
End By:
a. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Sep 29 18:57:48 UTC+0800 2019
6/6432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 432F BACKHOE LOADER SEJ
Configuration: 432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763413
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6195 Valve Spring Compressor 1
268-1969 Adapter 1
276-1221 Head 1
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the bottom face of the cylinder head. Check the depth of the valves below the face of
the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder
Head Valves" for the correct dimensions.
1/7432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position. Inlet valves have a recess in the center of the head.
Note: Do not stamp the heads of the valve. Stamping or punching the heads of the valves
could cause the valves to fracture.
3. Use a suitable lifting device to position the cylinder head with the valve springs upward.
The weight of the cylinder head is approximately 56 kg (125 lb).
Note: Ensure that the cylinder head is kept on a clean, soft surface in order to prevent
damage to the machined face.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 1 g01343550
2/7432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Typical example
4. Install Tooling (A) in position on the cylinder head in order to compress the appropriate
valve spring.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
Illustration 2 g01352229
Typical example
5. Apply sufficient pressure to Tooling (A) in order to remove valve keepers (1).
Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal
(4).
6. Slowly release the pressure on Tooling (A).
7. Remove valve spring retainer (2). Remove valve spring (3).
8. Repeat Steps 4 to 7 for the remaining valves.
3/7432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 9. Remove Tooling (A).
10. Remove valve stem seals (4).
11. Use a suitable lifting device to carefully turn over the cylinder head.
12. Remove valves (5).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
9U-6195 Valve Spring Compressor 1
268-1969 Adapter 1
276-1221 Head 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages and all lubrication passages in the cylinder head are free from debris. Follow Steps
1.a through 1.e in order to inspect the components of the cylinder head assembly. Replace
any components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to Systems Operation,
Testing and Adjusting, "Cylinder Head Inspect".
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" and Systems Operation, Testing and Adjusting, "Valve Guide -
Inspect" for further information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves".
e. Inspect the valve springs for the correct length. Refer to Specifications, "Cylinder
Head Valves".
4/7432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g01352229
2. Lubricate the stems of valves (5) with clean engine oil. Install valves (5) in the appropriate
positions in the cylinder head. Check the depth of the valves below the face of the cylinder
head. Refer to Systems Operation, Testing and Adjusting, "Valve Depth - Inspect" for more
information.
3. Use a suitable lifting device to carefully turn over the cylinder head. The weight of the
cylinder head is approximately 56 kg (125 lb).
Note: Ensure that all of the valves remain in place.
4. Install new valve stem seals (4) onto each of the valve guides.
Note: The outer face of the valve guides must be clean and dry before installing the valve
stem seals.
5. Install valve spring (3) onto the cylinder head. Position valve spring retainer (2) onto valve
spring (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
5/7432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 4 g01343550
Typical example
6. Install Tooling (A) in the appropriate position on the cylinder head in order to compress
valve spring (3).
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
7. Apply sufficient pressure to Tooling (A) in order to install valve keepers (1).
Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal
(4).
6/7432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
8. Carefully release the pressure on Tooling (A).
9. Repeat Steps 5 to 8 for the remaining valves.
10. Remove Tooling (A) from the cylinder head.
11. Use a suitable lifting device to position the cylinder head on a support. Ensure that the heads
of the valves are not obstructed. Lightly strike the top of the valves with a soft hammer in
order to ensure that valve keepers (1) are properly installed.
End By:
a. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Sep 29 18:58:44 UTC+0800 2019
7/7432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 432F BACKHOE LOADER SEJ
Configuration: 432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i04717030
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 157-3722 Valve Guide Driver 1
Start By:
A. Remove the inlet valves and the exhaust valves. Refer to Disassembly and Assembly, "Inlet
and Exhaust Valves - Remove and Install".
NOTICE
Removal and installation of the valve guide and valve seat must be
carried out by personnel with the correct training. Also special
machinery is required. For more information, refer to your authorized
Caterpillar dealer.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g01383763
1. Use Tooling (A) in order to remove valve guides (2) from cylinder head (1) .
2. Repeat the Step 1 for the remaining valve guides.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
157-3722 Valve Guide Driver 1
393-0369 Stop Collar 1
B 157-3720 Valve Seat Cutter 1
NOTICE
2/5432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Removal and installation of the valve guide and valve seat must be
carried out by personnel with the correct training. Also special
machinery is required. For more information, refer to your authorized
Caterpillar dealer.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the parent bores in the cylinder head for the valve guides.
Illustration 2 g01383767
2. Lubricate a new valve guide (2) and place the valve guide in position. Carefully tap the
valve guide in order to start the installation. Use Tooling (A) to install the valve guide into
the cylinder head.
3/5432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 3. Repeat Step 2 for the remaining valve guides.
Illustration 3 g01383769
4. Check protrusion (X) of valve guides (2). The valve guides should protrude 12.5 � .15 mm
(0.4921 � 0.0060 inch) above the valve spring recess. Refer to Specifications, "Cylinder
Head Valves" for more information.
5. After installation of valve guides (2), the valve guides must be reamed and the valve seat
inserts must be cut to the finished diameter. Follow Steps 5.a through 5.d in order to ream
the valve guides and cut the valve seat inserts.
a. Lubricate the bores of valve guides (2) with clean engine oil.
b. Use Tooling (B) in order to ream the valve guides. Ensure that even pressure is
applied to Tooling (B) .
c. Use Tooling (B) in order to cut the valve seats. Ensure that even pressure is applied to
Tooling (B) .
d. Ensure that the cylinder head is clean and free from machining debris.
6. Check the finished diameter of valve guides (2). Refer to Specifications, "Cylinder Head -
Valves" for more information.
7. Check the depths of the valves below the face of the cylinder head. Refer to System
Operation, Testing and Adjusting, "Valve Depth - Inspect" for more information.
End By: Install the inlet valves and the exhaust valves. Refer to Disassembly and Assembly,
"Inlet and Exhaust Valves - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Sun Sep 29 18:59:39 UTC+0800 2019
4/5432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 432F BACKHOE LOADER SEJ
Configuration: 432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763416
Engine Oil Filter Base - Remove and Install
SMCS - 1306-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Note: The oil filter may be installed vertically or the oil filter may be installed horizontally.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/4432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g01343554
Typical example
1. Use Tooling (A) to remove engine oil filter (3). Refer to Operation and Maintenance
Manual, "Engine Oil and Filter - Change".
2. If the engine oil pressure sensor is located in the engine oil filter base, remove the engine oil
pressure sensor. Refer to Disassembly and Assembly, "Engine Oil Pressure Sensor -
Remove and Install".
3. Remove bolts (4) and remove engine oil filter base (2).
4. Remove joint (1).
5. If the engine oil filter base has a spacer plate, remove the spacer plate and remove the joint.
6. If necessary, remove plug (6) from engine oil filter base (2). Remove O-ring seal (5) from
the plug.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 6V-6640 Sealant 1
NOTICE
2/4432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01343554
Typical example
1. Ensure that the engine oil filter base is clean. Clean the mating surfaces of the cylinder
block.
2. If necessary, install a new O-ring seal (5) to plug (6). Install plug (6) to engine oil filter base
(2). Tighten the plug to a torque of 12 N�m (106 lb in).
3. Install bolts (4) to engine oil filter base (2).
4. Install a new joint (1) onto bolts (4). If the engine oil filter base has a spacer plate, install the
spacer plate and a new joint onto the bolts.
5. Apply Tooling (B) to the threads of the bolts. Install the assembly of the engine oil filter
base to the cylinder block.
6. Tighten bolts (4) to a torque of 22 N�m (16 lb ft).
7. If the engine oil pressure sensor is located in the engine oil filter base, Install the engine oil
pressure sensor. Refer to Disassembly and Assembly, "Engine Oil Pressure Sensor -
Remove and Install".
8. Install a new engine oil filter (3). If necessary, fill the engine oil pan to the correct level that
is indicated on the oil level gauge. Refer to Operation and Maintenance Manual, "Engine
Oil Level - Check".
3/4432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 432F BACKHOE LOADER SEJ
Configuration: 432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i06801068
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container. Refer to Operation and
Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
2. Drain the engine lubricating oil into a suitable container. Refer to Operation and
Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.
1/3432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 3. If necessary, remove the electric starting motor. Refer to Disassembly and Assembly,
"Electric Starting Motor - Remove and Install".
Illustration 1 g01343557
Typical example
Illustration 2 g06118967
2/3432F Backhoe Loader SEJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/29https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...