This document provides instructions for removing and installing an engine water pump on a 428E backhoe loader. The removal procedure involves draining coolant, removing hoses and bolts, and removing the water pump. The installation procedure specifies cleaning parts, installing a new joint, aligning the water pump using guide bolts, and reinstalling bolts. Proper cleanup and alignment of parts is emphasized to prevent contamination and ensure correct assembly.
Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph0...ujfjjkskkemmd
This document provides instructions for removing and installing an engine water pump on a 428E backhoe loader. The removal procedure involves draining coolant, removing hoses and bolts, and removing the water pump. The installation procedure specifies cleaning parts, installing a new joint, aligning the water pump using guide bolts, and reinstalling bolts. Proper cleanup and alignment of parts is emphasized to prevent contamination and ensure correct assembly.
Caterpillar cat 428 d backhoe loader (prefix dsx) service repair manual (dsx0...ujfjjkskkemmd
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new gaskets and seals. Safety notices are included to warn technicians to contain fluids and wear protective equipment when working on the engine.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...ufjjdkfkksmme
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new seals and gaskets. Safety notices are included to handle fluids properly and avoid injury from spring-loaded components.
Caterpillar cat 312 e l excavator (prefix mjd) service repair manual (mjd0000...fjjsieskekfmmse
This document provides instructions for removing and installing an engine oil pan on a Caterpillar 312E L excavator. The key steps are:
1. Drain the oil and remove bolts and nuts to lift off the oil pan.
2. Clean surfaces and install a new gasket before positioning the oil pan back in place.
3. Apply threadlock and torque bolts to specifications to secure the oil pan.
Caterpillar cat 434 f backhoe loader (prefix ldh) service repair manual (ldh0...ufjsjekfksemm
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine.
The procedure for removing the engine oil pump involves removing the oil pan, suction pipe, and setscrews to detach the pump assembly. When installing, the procedure describes cleaning components, lubricating with oil, and tightening setscrews.
Removing the water pump requires draining coolant, loosening hoses, and removing setscrews. Installation involves installing a new gasket, tightening setscrews, and refilling the cooling system.
Removal of the water temperature regulator involves draining coolant below the component
This document provides instructions for removing and installing a cylinder head and camshaft on a 3054C engine. It outlines the necessary preparation steps, removal process which involves draining fluids and disconnecting components, and installation process which specifies cleaning, lubricating, and torquing components to the proper specifications. Tools required are also listed. The overall document provides a detailed technical procedure for servicing these engine components.
Caterpillar cat 438 d backhoe loader (prefix bpn) service repair manual (bpn0...ujdjfjjskekmm
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3054 engine.
The summary is:
1) The engine oil pump removal instructions include removing the oil pan, front housing, idler gear, retaining ring, and bolts to access and remove the pump.
2) The engine oil pump installation involves cleaning parts, applying threadlocker, installing the idler gear and retaining ring, and torquing bolts to spec.
3) Water pump removal requires draining coolant and removing bolts and nuts to access the pump.
4) Water pump disassembly for Type 1 engines involves removing bolts, seals, gears,
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...uuudfjjfjkkskm
This document provides instructions for removing and installing fuel injection nozzles and inlet/exhaust valves on a Caterpillar 3054 engine. It describes removing the fuel lines, loosening the nozzle nut, and removing the nozzle and seat washer. For installation, it details cleaning parts, installing a new seat washer, applying anti-seize compound, and tightening the nut. It also explains removing valve springs using a compressor, and installing new springs in the correct orientation.
Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph0...ujfjjkskkemmd
This document provides instructions for removing and installing an engine water pump on a 428E backhoe loader. The removal procedure involves draining coolant, removing hoses and bolts, and removing the water pump. The installation procedure specifies cleaning parts, installing a new joint, aligning the water pump using guide bolts, and reinstalling bolts. Proper cleanup and alignment of parts is emphasized to prevent contamination and ensure correct assembly.
Caterpillar cat 428 d backhoe loader (prefix dsx) service repair manual (dsx0...ujfjjkskkemmd
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new gaskets and seals. Safety notices are included to warn technicians to contain fluids and wear protective equipment when working on the engine.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...ufjjdkfkksmme
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new seals and gaskets. Safety notices are included to handle fluids properly and avoid injury from spring-loaded components.
Caterpillar cat 312 e l excavator (prefix mjd) service repair manual (mjd0000...fjjsieskekfmmse
This document provides instructions for removing and installing an engine oil pan on a Caterpillar 312E L excavator. The key steps are:
1. Drain the oil and remove bolts and nuts to lift off the oil pan.
2. Clean surfaces and install a new gasket before positioning the oil pan back in place.
3. Apply threadlock and torque bolts to specifications to secure the oil pan.
Caterpillar cat 434 f backhoe loader (prefix ldh) service repair manual (ldh0...ufjsjekfksemm
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine.
The procedure for removing the engine oil pump involves removing the oil pan, suction pipe, and setscrews to detach the pump assembly. When installing, the procedure describes cleaning components, lubricating with oil, and tightening setscrews.
Removing the water pump requires draining coolant, loosening hoses, and removing setscrews. Installation involves installing a new gasket, tightening setscrews, and refilling the cooling system.
Removal of the water temperature regulator involves draining coolant below the component
This document provides instructions for removing and installing a cylinder head and camshaft on a 3054C engine. It outlines the necessary preparation steps, removal process which involves draining fluids and disconnecting components, and installation process which specifies cleaning, lubricating, and torquing components to the proper specifications. Tools required are also listed. The overall document provides a detailed technical procedure for servicing these engine components.
Caterpillar cat 438 d backhoe loader (prefix bpn) service repair manual (bpn0...ujdjfjjskekmm
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3054 engine.
The summary is:
1) The engine oil pump removal instructions include removing the oil pan, front housing, idler gear, retaining ring, and bolts to access and remove the pump.
2) The engine oil pump installation involves cleaning parts, applying threadlocker, installing the idler gear and retaining ring, and torquing bolts to spec.
3) Water pump removal requires draining coolant and removing bolts and nuts to access the pump.
4) Water pump disassembly for Type 1 engines involves removing bolts, seals, gears,
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...uuudfjjfjkkskm
This document provides instructions for removing and installing fuel injection nozzles and inlet/exhaust valves on a Caterpillar 3054 engine. It describes removing the fuel lines, loosening the nozzle nut, and removing the nozzle and seat washer. For installation, it details cleaning parts, installing a new seat washer, applying anti-seize compound, and tightening the nut. It also explains removing valve springs using a compressor, and installing new springs in the correct orientation.
Caterpillar cat el240 b excavator (prefix 5wg) service repair manual (5wg0000...ufjjsjekksemmd
The document provides instructions for removing and installing an engine oil cooler on an excavator model EL240B. It describes removing the oil filter base, then removing the oil cooler and its gasket and O-ring seals. For installation, it describes installing new O-ring seals and gasket on the oil cooler before installing it along with the gasket and tightening bolts, then reinstalling the oil filter base.
This document provides instructions for removing and installing the engine oil filter base and oil cooler on a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions, and gives step-by-step instructions including illustrations of the process. The instructions note to drain coolant, remove bolts and parts, clean and apply new seals, and reinstall following the reverse order of removal. A second section provides similar instructions for disassembling and assembling the engine oil pump.
Caterpillar cat d400 e ii ejector truck (prefix apf) service repair manual (a...fjsqazkekdmme
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a D400E II Ejector Truck. It describes the required tools and safety precautions for each step. The procedure involves compressing springs, removing retainers, lubricating parts, and ensuring proper heights and locations are achieved during installation. A second section provides instructions for disassembling the engine oil filter base to access internal valves and springs.
This document provides instructions for removing and installing the engine oil filter base and oil cooler on a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions, and gives step-by-step instructions including illustrations of the process. The instructions cover draining coolant, removing bolts and parts, applying a new oil seal, reinstalling components and refilling the cooling system. A second section provides similar instructions for disassembling, cleaning and assembling the engine oil pump.
Caterpillar cat 312 c excavator (prefix fds) service repair manual (fds00301 ...fjsjjekdkme
1. The document provides instructions for removing and installing the front housing of a 312C excavator engine.
2. To remove the front housing, several other components must first be removed, including the alternator, water pump, and crankshaft pulley. Bolts securing the front housing to other parts are then loosened and removed.
3. Installation involves cleaning surfaces, installing new seals if needed, and securing the front housing with bolts to the cylinder block, oil pan, and other parts. Timing gear alignment must also be checked during installation.
Caterpillar cat 323 d l excavator (prefix bym) service repair manual (bym0000...fjskksmem
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from the cylinder head of a C6.4 engine. It describes using various tools to notch, extract, and install the valve seat inserts.
2. Additional instructions cover removing, disassembling, and assembling the engine oil cooler. Steps include disconnecting hoses and fasteners, and removing individual components like the cooler core and covers.
3. Precautions are given to keep all parts clean and free of contaminants, which can cause damage and premature wear.
Jcb 536 t70 lp telescopic handler service repair manual sn 2336575 and upfiskefjskemem
This service manual provides instructions for servicing Loadall rough terrain variable reach trucks. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics, and electrical systems. Specific models covered include 526-56, 531-70, 533-105, 535-95, 536-60, and others. Safety warnings are provided throughout and procedures for removal and installation are described in detail with torque specifications.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fjjksekksemm
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine.
The procedure for removing the engine oil pump involves draining oil, removing mounting screws and pipes, and removing the pump assembly. Installation requires cleaning, inspecting parts, lubricating with oil, and securing everything with screws.
Removing the water pump requires draining coolant, loosening hoses and clamps, and removing mounting screws. Installation involves installing a new gasket, securing with screws treated with sealant or locktite, filling the system, and reattaching hoses.
Removal of the water temperature regulator involves draining cool
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fujsjefksekmfm
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3054C engine. It describes the removal and installation procedures in step-by-step detail, highlighting important safety notices and precautions. The removal procedure for the engine oil pump involves removing mounting screws and other components. The installation procedure describes cleaning, inspecting, and lubricating parts before securing the pump with mounting screws. The water pump removal requires draining coolant and removing mounting screws and hoses. Installation involves installing a new gasket and securing the pump with threadlocked mounting screws.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...ujdjfjjkskkmme
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new seals and gaskets. Safety notices are included to handle fluids properly and avoid injury from spring-loaded components.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fusjejfjksaekmm
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3054C engine. It describes:
1. Removing the oil pan and suction pipe before removing the engine oil pump assembly from the cylinder block using setscrews.
2. Cleaning and inspecting oil pump components before installation and lubricating parts with oil.
3. Installing the oil pump assembly using setscrews and checking backlash after installation.
4. Draining coolant before removing the water pump and fan. Removing the water pump involves setscrews and installing involves a new gasket and setscrews with sealant.
This document provides instructions for removing and installing the engine oil pump on Caterpillar 3054C engines without a balancer. It describes:
1. Removing the oil pan, suction pipe, and setscrews to detach the oil pump assembly from the cylinder block.
2. Inspecting internal oil pump components and replacing the entire pump if worn or damaged.
3. Cleaning and lubricating oil pump parts before installing, checking clearances, and refilling with oil.
4. Reattaching the oil pump to the cylinder block and reinstalling other parts in reverse order of removal.
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 442E backhoe loader. The procedures describe draining fluids, removing fasteners and hoses, cleaning components, installing new seals and fasteners, and refilling fluids. Safety notices are provided regarding containing fluids, wearing protective equipment, and inspecting parts for wear.
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 442E backhoe loader engine. The procedures describe draining fluids, removing fasteners and hoses, cleaning components, installing new seals and fasteners, and refilling fluids. Safety notices are provided regarding containing fluids, wearing protective equipment, and inspecting parts for wear.
This document provides instructions for removing and installing the engine oil pump on Caterpillar 3054C engines without a balancer. It describes:
1. Removing the oil pan, suction pipe, and setscrews to detach the oil pump assembly from the cylinder block.
2. Inspecting internal oil pump components and replacing the entire pump if worn or damaged.
3. Cleaning and lubricating oil pump parts before installing, checking clearances, and refilling with oil.
4. Reattaching the oil pump to the cylinder block and reinstalling other parts in reverse order of removal.
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 442E backhoe loader engine. The procedures describe draining fluids, removing fasteners and hoses, cleaning components, installing new seals and fasteners, and refilling fluids. Safety notices are provided regarding containing fluids, wearing protective equipment, and inspecting parts for wear.
Caterpillar cat 428 d backhoe loader (prefix dsx) service repair manual (dsx0...fujsekfkksemm
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3054C engine. The oil pump removal procedure involves removing mounting screws and detaching the pump assembly from the engine block. The water pump removal requires draining coolant, loosening hoses, and removing mounting screws. Installation is the reverse of removal, ensuring new gaskets are used and components are clean. Sealant is used on oil pump and water pump mounting screws for proper sealing.
Caterpillar cat 432 f backhoe loader (prefix pxr) service repair manual (pxr0...fujsefkxswksemm
This document provides assembly instructions for the axle housing of a 432F backhoe loader. It outlines 34 steps to assemble components like bearings, brake discs, seals and pins. Special tools are required and cleanliness is important. Measurements are taken and shims selected to achieve proper torque specifications. Springs and cylinders are installed last.
Caterpillar cat 432 f backhoe loader (prefix lnr) service repair manual (lnr0...fujsefkxswksemm
This document provides assembly instructions for a 432F backhoe loader transmission. It describes assembling the transmission case and installing various components like shafts, gears, seals and bearings. Special tools are required and safety precautions mentioned. Assembly is done in main components that are then assembled together. Clearances are checked using gauges and shims added or removed to get the specified tolerances.
Caterpillar cat 432 e backhoe loader (prefix rxs) service repair manual (rxs0...fujsefkxswksemm
This document provides instructions for removing and installing an engine on a 432E backhoe loader. The removal process involves 50 steps that disconnect wiring harnesses, hoses, tubes, and remove mounting hardware. The installation is the reverse of removal, requiring reconnecting all components and tightening mounting bolts to the specified torques. Special tools are required to lift and support the heavy engine assembly during removal and installation.
Caterpillar cat 432 e backhoe loader (prefix jba) service repair manual (jba0...fujsefkxswksemm
The document provides step-by-step instructions for disassembling the transmission of a 432E Backhoe Loader. It lists required tools and outlines the procedure for removing various transmission components including gears, shafts, bearings, seals and other parts. Detailed illustrations accompany each step to show how to use specialized tools to compress springs, remove retaining rings, and disassemble clutches, synchronizers and other mechanisms. Safety notices are included to warn of potential injury from compressed springs or other hazards.
New holland c232 tier 4 compact track loader service repair manual [ndm451672...fujsefkxswksemm
This service manual provides instructions for servicing engines and components for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders including removing the engine by draining fluids, disconnecting electrical components and hoses, removing covers and fans, and then fully removing the engine. Specific models and applicable component removal steps are provided for C232, C238, L223, L225 and L230 Tier 4 engines.
Caterpillar cat el240 b excavator (prefix 5wg) service repair manual (5wg0000...ufjjsjekksemmd
The document provides instructions for removing and installing an engine oil cooler on an excavator model EL240B. It describes removing the oil filter base, then removing the oil cooler and its gasket and O-ring seals. For installation, it describes installing new O-ring seals and gasket on the oil cooler before installing it along with the gasket and tightening bolts, then reinstalling the oil filter base.
This document provides instructions for removing and installing the engine oil filter base and oil cooler on a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions, and gives step-by-step instructions including illustrations of the process. The instructions note to drain coolant, remove bolts and parts, clean and apply new seals, and reinstall following the reverse order of removal. A second section provides similar instructions for disassembling and assembling the engine oil pump.
Caterpillar cat d400 e ii ejector truck (prefix apf) service repair manual (a...fjsqazkekdmme
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a D400E II Ejector Truck. It describes the required tools and safety precautions for each step. The procedure involves compressing springs, removing retainers, lubricating parts, and ensuring proper heights and locations are achieved during installation. A second section provides instructions for disassembling the engine oil filter base to access internal valves and springs.
This document provides instructions for removing and installing the engine oil filter base and oil cooler on a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions, and gives step-by-step instructions including illustrations of the process. The instructions cover draining coolant, removing bolts and parts, applying a new oil seal, reinstalling components and refilling the cooling system. A second section provides similar instructions for disassembling, cleaning and assembling the engine oil pump.
Caterpillar cat 312 c excavator (prefix fds) service repair manual (fds00301 ...fjsjjekdkme
1. The document provides instructions for removing and installing the front housing of a 312C excavator engine.
2. To remove the front housing, several other components must first be removed, including the alternator, water pump, and crankshaft pulley. Bolts securing the front housing to other parts are then loosened and removed.
3. Installation involves cleaning surfaces, installing new seals if needed, and securing the front housing with bolts to the cylinder block, oil pan, and other parts. Timing gear alignment must also be checked during installation.
Caterpillar cat 323 d l excavator (prefix bym) service repair manual (bym0000...fjskksmem
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from the cylinder head of a C6.4 engine. It describes using various tools to notch, extract, and install the valve seat inserts.
2. Additional instructions cover removing, disassembling, and assembling the engine oil cooler. Steps include disconnecting hoses and fasteners, and removing individual components like the cooler core and covers.
3. Precautions are given to keep all parts clean and free of contaminants, which can cause damage and premature wear.
Jcb 536 t70 lp telescopic handler service repair manual sn 2336575 and upfiskefjskemem
This service manual provides instructions for servicing Loadall rough terrain variable reach trucks. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics, and electrical systems. Specific models covered include 526-56, 531-70, 533-105, 535-95, 536-60, and others. Safety warnings are provided throughout and procedures for removal and installation are described in detail with torque specifications.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fjjksekksemm
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine.
The procedure for removing the engine oil pump involves draining oil, removing mounting screws and pipes, and removing the pump assembly. Installation requires cleaning, inspecting parts, lubricating with oil, and securing everything with screws.
Removing the water pump requires draining coolant, loosening hoses and clamps, and removing mounting screws. Installation involves installing a new gasket, securing with screws treated with sealant or locktite, filling the system, and reattaching hoses.
Removal of the water temperature regulator involves draining cool
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fujsjefksekmfm
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3054C engine. It describes the removal and installation procedures in step-by-step detail, highlighting important safety notices and precautions. The removal procedure for the engine oil pump involves removing mounting screws and other components. The installation procedure describes cleaning, inspecting, and lubricating parts before securing the pump with mounting screws. The water pump removal requires draining coolant and removing mounting screws and hoses. Installation involves installing a new gasket and securing the pump with threadlocked mounting screws.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...ujdjfjjkskkmme
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new seals and gaskets. Safety notices are included to handle fluids properly and avoid injury from spring-loaded components.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fusjejfjksaekmm
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3054C engine. It describes:
1. Removing the oil pan and suction pipe before removing the engine oil pump assembly from the cylinder block using setscrews.
2. Cleaning and inspecting oil pump components before installation and lubricating parts with oil.
3. Installing the oil pump assembly using setscrews and checking backlash after installation.
4. Draining coolant before removing the water pump and fan. Removing the water pump involves setscrews and installing involves a new gasket and setscrews with sealant.
This document provides instructions for removing and installing the engine oil pump on Caterpillar 3054C engines without a balancer. It describes:
1. Removing the oil pan, suction pipe, and setscrews to detach the oil pump assembly from the cylinder block.
2. Inspecting internal oil pump components and replacing the entire pump if worn or damaged.
3. Cleaning and lubricating oil pump parts before installing, checking clearances, and refilling with oil.
4. Reattaching the oil pump to the cylinder block and reinstalling other parts in reverse order of removal.
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 442E backhoe loader. The procedures describe draining fluids, removing fasteners and hoses, cleaning components, installing new seals and fasteners, and refilling fluids. Safety notices are provided regarding containing fluids, wearing protective equipment, and inspecting parts for wear.
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 442E backhoe loader engine. The procedures describe draining fluids, removing fasteners and hoses, cleaning components, installing new seals and fasteners, and refilling fluids. Safety notices are provided regarding containing fluids, wearing protective equipment, and inspecting parts for wear.
This document provides instructions for removing and installing the engine oil pump on Caterpillar 3054C engines without a balancer. It describes:
1. Removing the oil pan, suction pipe, and setscrews to detach the oil pump assembly from the cylinder block.
2. Inspecting internal oil pump components and replacing the entire pump if worn or damaged.
3. Cleaning and lubricating oil pump parts before installing, checking clearances, and refilling with oil.
4. Reattaching the oil pump to the cylinder block and reinstalling other parts in reverse order of removal.
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 442E backhoe loader engine. The procedures describe draining fluids, removing fasteners and hoses, cleaning components, installing new seals and fasteners, and refilling fluids. Safety notices are provided regarding containing fluids, wearing protective equipment, and inspecting parts for wear.
Caterpillar cat 428 d backhoe loader (prefix dsx) service repair manual (dsx0...fujsekfkksemm
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3054C engine. The oil pump removal procedure involves removing mounting screws and detaching the pump assembly from the engine block. The water pump removal requires draining coolant, loosening hoses, and removing mounting screws. Installation is the reverse of removal, ensuring new gaskets are used and components are clean. Sealant is used on oil pump and water pump mounting screws for proper sealing.
Similar to Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph00001 and up) (10)
Caterpillar cat 432 f backhoe loader (prefix pxr) service repair manual (pxr0...fujsefkxswksemm
This document provides assembly instructions for the axle housing of a 432F backhoe loader. It outlines 34 steps to assemble components like bearings, brake discs, seals and pins. Special tools are required and cleanliness is important. Measurements are taken and shims selected to achieve proper torque specifications. Springs and cylinders are installed last.
Caterpillar cat 432 f backhoe loader (prefix lnr) service repair manual (lnr0...fujsefkxswksemm
This document provides assembly instructions for a 432F backhoe loader transmission. It describes assembling the transmission case and installing various components like shafts, gears, seals and bearings. Special tools are required and safety precautions mentioned. Assembly is done in main components that are then assembled together. Clearances are checked using gauges and shims added or removed to get the specified tolerances.
Caterpillar cat 432 e backhoe loader (prefix rxs) service repair manual (rxs0...fujsefkxswksemm
This document provides instructions for removing and installing an engine on a 432E backhoe loader. The removal process involves 50 steps that disconnect wiring harnesses, hoses, tubes, and remove mounting hardware. The installation is the reverse of removal, requiring reconnecting all components and tightening mounting bolts to the specified torques. Special tools are required to lift and support the heavy engine assembly during removal and installation.
Caterpillar cat 432 e backhoe loader (prefix jba) service repair manual (jba0...fujsefkxswksemm
The document provides step-by-step instructions for disassembling the transmission of a 432E Backhoe Loader. It lists required tools and outlines the procedure for removing various transmission components including gears, shafts, bearings, seals and other parts. Detailed illustrations accompany each step to show how to use specialized tools to compress springs, remove retaining rings, and disassemble clutches, synchronizers and other mechanisms. Safety notices are included to warn of potential injury from compressed springs or other hazards.
New holland c232 tier 4 compact track loader service repair manual [ndm451672...fujsefkxswksemm
This service manual provides instructions for servicing engines and components for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders including removing the engine by draining fluids, disconnecting electrical components and hoses, removing covers and fans, and then fully removing the engine. Specific models and applicable component removal steps are provided for C232, C238, L223, L225 and L230 Tier 4 engines.
Caterpillar cat 432 e backhoe loader (prefix bxe) service repair manual (bxe0...fujsefkxswksemm
This document provides instructions for removing and installing various engine components on a Caterpillar 432E backhoe loader, including:
- Removing and installing V-belts
- Removing and installing the fan, fan drive, and alternator
- Procedures include removing set screws, disconnecting wiring harnesses, adjusting belt tension, and reconnecting components.
The summary provides an overview of the types of components covered in the repair manual and the basic removal and installation steps involved without including excessive technical details.
Caterpillar cat 432 d backhoe loader (prefix wep) service repair manual (wep0...fujsefkxswksemm
This document provides instructions for removing and installing an engine oil cooler and engine oil relief valve on a Caterpillar 3054C engine. The summary is:
1. Drain coolant and oil from the engine oil cooler before removing housing bolts and seals.
2. Clean mating surfaces and install new seals and gasket before bolting the housing back onto the engine with new bolts.
3. Remove the plug and spring to access the engine oil relief valve plunger. Inspect parts and lubricate before reinstalling.
4. Drain the oil pan before removing bolts to access the engine oil pump. Remove bolts and suction pipe to remove the pump assembly.
Caterpillar cat 432 d backhoe loader (prefix tdr) service repair manual (tdr0...fujsefkxswksemm
This document provides instructions for removing and assembling components of a Caterpillar 3054C engine, including the cylinder head. The removal procedure for the cylinder head involves first draining fluids, removing related components like the exhaust manifold and fuel injectors, and then loosening and removing mounting screws to lift the cylinder head off the engine block. Proper care is emphasized to prevent damage to parts and contain fluids during disassembly.
Caterpillar cat 322 c excavator (prefix daa) service repair manual (daa00001 ...fujsefkxswksemm
The document provides instructions for disassembling and assembling the pilot valve (joystick) of a 322C excavator. It consists of 20 steps for disassembly and 23 steps for assembly. Key parts of the pilot valve that are disassembled include the spool assembly, springs, seals, rods and plugs. Cleanliness is emphasized during both disassembly and assembly. O-rings and seals are replaced during assembly.
New holland br6080 round balers service repair manualfujsefkxswksemm
This service manual provides instructions for servicing and repairing various systems of a baler, including hydraulic, electrical, electronic, lubrication, engine, transmission, axles, brakes, wheels, and crop processing systems. It outlines safety procedures and contains diagrams, part numbers, specifications and troubleshooting information. Torque specifications are provided for hardware.
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It describes:
1. Removing fuel and oil lines, clips, bolts and pins to detach the governor from the engine.
2. Installing new O-rings, attaching the governor to the engine with bolts and pins, and reconnecting fuel and oil lines.
3. Checking the fuel setting adjustment after installation.
It also references other documents for additional governor information and maintenance guidelines.
Caterpillar cat 320 c l excavator (prefix anb) service repair manual (anb0000...fujsefkxswksemm
The document provides instructions for removing and installing various components on a 320C excavator, including:
1) Removing and installing actuator motors that control air dampers and distributors by disconnecting wiring harnesses, removing screws and linkage attachments, and reversing the process for installation.
2) Removing and installing a fan speed control unit by disconnecting its wiring harness, removing mounting screws, and reversing the process for installation.
3) Removing and installing an ambient air temperature sensor by removing mounting plates and bolts, disconnecting its wiring harness, and reversing the process for installation.
4) Removing and installing a coolant temperature sensor by disconnecting its wiring harness and reversing the process for installation.
Caterpillar cat 320 c excavator (prefix sbn) service repair manual (sbn00001 ...fujsefkxswksemm
This document provides instructions for removing and installing a flywheel housing on a 320C excavator engine. It describes:
1. Removing the electric starting motor and flywheel/ring gear as preliminary steps.
2. Using various tools like a link bracket and driver group to remove the 12 bolts securing the adapter to the flywheel housing and then remove the housing.
3. Reversing the process to install a new or repaired flywheel housing, ensuring all bolts are properly tightened.
Caterpillar cat 320 c excavator (prefix bcn) service repair manual (bcn00001 ...fujsefkxswksemm
This document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Fuel filter base
- Fuel injection lines
- Fuel injection nozzles
- Fuel shutoff solenoid
- Fuel injection pump
The procedures describe disconnecting fuel lines, removing mounting bolts and other hardware, taking care to plug openings to prevent contamination. Proper tools are listed and installation is the reverse of removal. Safety notices warn to contain fluids and keep parts clean.
Case ih stx325 steiger tractor service repair manual pin jee0102001 and afterfujsefkxswksemm
The document provides instructions for removing and installing the engine on STX Steiger tractors. It is a 12-step process for removal that includes draining fluids, disconnecting wiring and hoses, and using an overhead hoist to lift the engine out of the tractor. The 13-step installation process reverses these steps, lowering the engine back into place and reconnecting all components. Safety warnings are provided throughout regarding working around heavy components, hot or pressurized fluids, and ensuring the engine is properly supported during removal and installation.
Caterpillar cat 951 c track loader (prefix 69h) service repair manual (69h018...fujsefkxswksemm
This document provides instructions for servicing a 951B track loader. It includes general instructions for disassembly and assembly, safety procedures, cleaning and handling of parts, removal and installation of components, use of service tools, and information on specific components like bearings, bolts, gaskets and more. The instructions aim to ensure repairs are done correctly and safely.
Caterpillar cat 931 b track loader (prefix 30y) service repair manual (30y000...fujsefkxswksemm
This service repair manual provides instructions for removing and installing various components of a Caterpillar 931B track loader, including:
1) Track roller frames, which are removed by taking off guards, yokes, and bolts, and lifted with straps and a hoist.
2) Pivot shafts, by removing seals, bearings, and support assemblies after draining oil and using straps and hoists.
3) Equalizer bars, which are removed by taking off guards and pins after jacking up the machine.
Caterpillar cat 931 b track loader (prefix 26y) service repair manual (26y000...fujsefkxswksemm
This document provides instructions for removing and installing steering clutches on a 931B track loader. It begins by listing the necessary preparatory steps of removing the hydraulic tank, fuel tank, battery, brake linkage, and disconnecting hoses and wiring. It then details removing each individual component of the steering clutch assembly, including the cylinder, plates, springs, housing, and linkages. The instructions conclude by describing how to reinstall each part in reverse order and providing final checks and replacements of ancillary components.
This document provides safety warnings and instructions for removing and installing an engine. It contains 51 steps to remove the engine, which include disconnecting batteries, draining coolant, removing hoses, wires, and other components. It then lists 40 steps to reinstall the engine, reversing the removal process and reconnecting all components. The purpose is to provide a detailed procedure for safely removing and reinstalling an engine.
Caterpillar cat 931 b track loader (prefix 4sc) service repair manual (4sc000...fujsefkxswksemm
This document provides instructions for removing and installing track carrier rollers, track roller guards, and track rollers on a Caterpillar 931B track loader. It describes loosening the track, removing covers and guards, and then removing rollers by taking off bolts and lockwashers. Reinstallation involves cleaning surfaces, applying lubricant, pressing in bearings, and installing seals before reattaching rollers and guards with bolts. Detailed steps are provided for disassembling and assembling the individual components of the track roller assemblies.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428E BACKHOE LOADER DPH
Configuration: 428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763421
Engine Oil Relief Valve - Remove and Install - Engines
Without a Balancer Unit
SMCS - 1315-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Personal injury can result from being struck by parts propelled by a
released spring force.
1/4428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 1 g01343561
Typical example
1. Remove bolts (6) and suction pipe (7).
2. Remove the joint from suction pipe (5) (not shown).
3. Loosen cap (2). Carefully remove cap (2) from the housing of engine oil pump (1).
Note: The spring force will be released when the cap is removed.
4. Remove spring (4) from the bore for the relief valve in the housing of engine oil pump (1).
5. Use Tooling (A) to remove plunger (3) from the bore for the relief valve in the housing of
engine oil pump (1).
Installation Procedure
Table 2
2/4428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Required Tools
Tool Part Number Part Description Qty
B 4C-9506 Retaining Compound 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01343561
Typical example
1. Ensure that all components are clean and free from wear or damage. If necessary, replace
any components that are worn or damaged. If the bore for the relief valve in the housing of
engine oil pump (1) is worn or damaged, the complete assembly of the engine oil pump
must be replaced.
3/4428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Lubricate plunger (3) with clean engine oil. Use long nose pliers to install plunger (3) and
spring (4) into the bore for the relief valve in the housing of engine oil pump (1).
Note: The plunger must slide freely in the bore for the relief valve.
3. Apply Tooling (A) to the threads of cap (2). Install cap (2) to engine oil pump (1). Tighten
the cap to a torque of 35 N·m (26 lb ft).
Note: Ensure that the spring is properly located inside the plunger and the cap. Ensure that
Tooling (A) does not contaminate the bore for the relief valve in the housing of engine oil
pump.
4. Install suction pipe (7) and a new joint (5) to the assembly of the engine oil pump.
5. Install bolts (6). Tighten the bolts to a torque to 22 N·m (16 lb ft).
End By:
a. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 28 20:31:21 UTC+0800 2019
4/4428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428E BACKHOE LOADER DPH
Configuration: 428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763420
Engine Oil Pump - Remove and Install - Engines Without a
Balancer Unit
SMCS - 1304-010
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Note: This procedure is for the removal of the engine oil pump on engines that are not equipped
with a balancer. Refer to Disassembly and Assembly, "Balancer Group - Remove" for information
on the removal of the engine oil pump for engines that are equipped with a balancer.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/7428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01343631
Typical example
1. Remove bolts (1) and suction pipe (2).
2. Remove the joint from suction pipe (2).
3. Remove bolts (5). Remove the assembly of engine oil pump (3) from the cylinder block.
4. If necessary, remove pressure relief valve (4) from the housing of engine oil pump (3).
Refer to Disassembly and Assembly, "Engine Oil Relief Vave - Remove and Install".
2/7428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 2 g01343633
Typical example
5. If necessary, remove bolts (9) and front cover assembly (6). Remove outer rotor (7) from
the housing of engine oil pump (3).
Note: Do not remove dowels (8) and (10) from the housing of the engine oil pump unless
the dowels are damaged.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7324 Indicator Bracket 1
3/7428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
Note: This procedure is for the installation of the engine oil pump on engines that are not
equipped with a balancer. Refer to Disassembly and Assembly, "Balancer Group - Install" for
information on the installation of the engine oil pump for engines that are equipped with a
balancer.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
If any of the parts on the engine oil pump are worn or damaged, the
entire pump must be replaced.
1. Ensure that all components of the engine oil pump are clean and free from wear or damage.
Check the clearance between the outer rotor of the oil pump and the oil pump body. Check
the clearance between the outer rotor and the inner rotor. Check the end play of the rotor.
Refer to the Systems Operation,Testing and Adjusting, "Engine Oil Pump - Inspect".
Replace the complete assembly of the engine oil pump if any of the components are worn or
damaged.
4/7428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 3 g01343633
2. If necessary, lubricate the internal components of the assembly of the engine oil pump with
clean engine oil. Install outer rotor (7) and front cover (6) to the housing of engine oil pump
(3). Install bolts (9). Tighten the bolts to a torque of 9.5 N·m (84 lb in).
5/7428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 4 g01343631
3. If necessary, install pressure relief valve (4). Refer to Disassembly and Assembly, "Engine
Oil Relief Valve - Remove and Install" for further information.
4. Ensure that dowels (8) and (10) are correctly located in the housing of engine oil pump (3).
Position the assembly of the engine oil pump onto the cylinder block.
Note: Ensure that the dowels in the housing of the engine oil pump are aligned with the
holes in the cylinder block.
5. Install bolts (5). Tighten the bolts to a torque of 44 N·m (32 lb ft).
6. Install suction pipe (2) and a new joint to the assembly of the engine oil pump.
7. Install bolts (1). Tighten the bolts to a torque to 22 N·m (16 lb ft).
8. Use Tooling (A) in order to check the backlash between the idler gear of the oil pump and
the crankshaft gear. Refer to Specifications, "Gear Group - Front" for further information.
End By:
a. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Sat Sep 28 20:32:09 UTC+0800 2019
6/7428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428E BACKHOE LOADER DPH
Configuration: 428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763422
Water Pump - Remove
SMCS - 1361-011
Removal Procedure
Start By:
a. Remove the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/3428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the
correct procedure.
2. Loosen the hose clamps and remove the hose from the water pump inlet.
Illustration 1 g01263054
Typical example
3. Remove bolts (4). The bolts are different lengths. Note the positions of the different bolts.
Note: Do not remove bolts (7) at this time.
4. Remove water pump (3) from front cover (1).
Note: If necessary, tap the water pump with a soft hammer in order to loosen the water
pump.
2/3428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 5. Remove joint (2).
6. If necessary, remove cover (6) from the water pump. Follow Steps 6.a through 6.c in order
to remove the cover.
a. Remove bolts (7).
b. Remove cover (6).
c. Remove joint (5).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 28 20:32:56 UTC+0800 2019
3/3428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428E BACKHOE LOADER DPH
Configuration: 428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763423
Water Pump - Install
SMCS - 1361-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Bolt
(M8 by 80 mm)
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the water pump is clean and free from wear or damage. If necessary, replace the
water pump.
1/4428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g01269391
Typical example
2. If necessary, install cover (6) to water pump (3). Follow Steps 2.a through 2.d in order to
install the cover.
a. Clean the mating surface of cover (6).
b. Position a new joint (5) onto water pump (3).
c. Install cover (6) to water pump (3).
d. Install bolts (7) to cover (6). Tighten the bolts finger tight.
3. Clean the mating surface of front cover (1).
2/4428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g01269392
4. Install Tooling (A) in position (X).
5. Use Tooling (A) in order to align a new joint (2) to front cover (1). Install the joint to the
front cover.
6. Align water pump (3) with Tooling (A). Install the water pump to front cover (1).
Note: Ensure that the gear of the water pump and the gear of the fuel injection pump mesh.
7. Install bolts (4). Refer to Illustration 1. Tighten the bolts finger tight.
Note: Ensure that bolts of different lengths are installed in the correct positions.
8. Remove Tooling (A) and install remaining bolts (4) finger tight.
3/4428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 3 g01269393
Tightening sequence for the water pump
9. Tighten bolts (4) and bolts (7) to a torque of 22 N·m (16 lb ft). Refer to Illustration 1.
Tighten the bolts in the sequence that is shown in Illustration 3.
10. Install the hose to the water pump inlet. Tighten the hose clamps.
11. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling
System Coolant - Change" for the correct procedure.
End By:
a. Install the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove and
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 28 20:33:44 UTC+0800 2019
4/4428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428E BACKHOE LOADER DPH
Configuration: 428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763424
Water Temperature Regulator - Remove and Install
SMCS - 1355-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system to a level below the water temperature regulator,
into a suitable container for storage or for disposal. Refer to Operation and Maintenance
Manual, "Cooling System Coolant - Change" for the correct draining procedure.
2. Loosen the hose clamps from the upper radiator hose and disconnect the upper radiator hose
from water temperature regulator housing (2).
1/5428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Illustration 1 g01343959
Typical example
3. Remove bolts (1) from water temperature regulator housing (2).
4. Remove water temperature regulator housing (2) from the cylinder head.
Note: Note the orientation of the water temperature regulator housing.
2/5428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 2 g01343959
Typical example
5. Remove O-ring seal (3) from water temperature regulator housing (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6396 O-Ring Assembly Compound 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that all components of water temperature regulator are clean and free of wear or
damage. Check the water temperature regulator for correct operation. Refer to Systems
3/5428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Operation, Testing and Adjusting, "Water Temperature Regulator - Test" for the procedure
to test the water temperature regulator. If any components of the water temperature
regulator are worn or damaged, the complete assembly must be replaced.
Illustration 3 g01343960
Typical example
2. If the original water temperature regulator housing is installed, position a new O-ring seal
(3) into the groove in water temperature regulator housing (2).
A new water temperature regulator housing is supplied with a new O-ring seal.
3. Use Tooling (A) to lubricate the new O-ring seal.
4. Install water temperature regulator housing (2) to the cylinder head.
Note: Ensure the correct orientation of the water temperature regulator housing.
4/5428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 4 g01343959
Typical example
5. Install bolts (1). Tighten the bolts to a torque of 22 N·m (16 lb ft).
6. Connect the upper radiator hose and tighten the hose clamps.
7. Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual,
"Cooling System Coolant - Change" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 28 20:34:32 UTC+0800 2019
5/5428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428E BACKHOE LOADER DPH
Configuration: 428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763425
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Bolt
(1/2 inch - UNF by 4 inch)
2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g01245126
Typical example
1. Remove two bolts from positions (X) on flywheel (1).
2. Install Tooling (A) to positions (X) on flywheel (1).
3. Attach a suitable lifting device to flywheel (1). Support the weight of the flywheel. The
weight of the flywheel is approximately 71 kg (155 lb).
4. Remove remaining bolts (2).
5. Use the lifting device in order to remove the flywheel from the engine.
2/3428E Backhoe Loader DPH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...