The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also describes removing the existing rear seal housing assembly by removing setscrews, protecting the crankshaft during new seal installation, aligning and tightening the new housing assembly setscrews, and installing the flywheel.
Caterpillar cat 416 d backhoe loader (prefix b2d) service repair manual (b2d0...fujsjefjsekkem
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054C engine. It outlines the required tools and steps to:
1. Remove the bolts securing the flywheel housing and lifting it off the engine.
2. Clean the engine mating surface before installation.
3. Position the flywheel housing on the engine and secure it with bolts, using link brackets to aid in alignment.
Caterpillar cat 416 d backhoe loader (prefix b2d) service repair manual (b2d0...fjjsekfkksefm
This document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes:
1. Cleaning the flywheel housing and inspecting the crankshaft rear seal for leaks.
2. Heating the ring gear and quickly installing it onto the flywheel.
3. Using guide bolts and a lifting device to position the flywheel, then installing and tightening the bolts.
Caterpillar cat 416 d backhoe loader (prefix b2d) service repair manual (b2d0...fujsjefkskekmm
This document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes:
1. Cleaning the flywheel housing and inspecting the crankshaft rear seal for leaks.
2. Heating the ring gear and quickly installing it on the flywheel.
3. Installing the flywheel using guide bolts and lifting equipment, and tightening the bolts to the specified torque.
4. Removing the crankshaft rear seal housing assembly, which must be replaced if removed.
5. Installing the new crankshaft rear seal housing assembly using a plastic sleeve to protect the seal, and tightening the
Caterpillar cat 416 d backhoe loader (prefix b2d) service repair manual (b2d0...fjjsekkksemm
This document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes:
1. Cleaning and preparing the flywheel housing and crankshaft.
2. Heating the ring gear and quickly installing it on the flywheel.
3. Using guide bolts and lifting brackets to position the flywheel, then tightening the bolts to the specified torque.
4. Checking that the housing assembly is clean before installing the new crankshaft rear seal assembly using setscrews.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
The document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054C engine. It describes using guide bolts and a link bracket to support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing assembly. The new seal assembly is installed with a plastic sleeve to protect the seal lip and set screws are used to secure it to the cylinder block.
The document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054C engine. It describes using guide bolts and a link bracket to support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing assembly. The new seal assembly is installed with a plastic sleeve to protect the seal lip and set screws are used to secure it to the cylinder block.
Caterpillar cat 416 d backhoe loader (prefix b2d) service repair manual (b2d0...fujsjefjsekkem
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054C engine. It outlines the required tools and steps to:
1. Remove the bolts securing the flywheel housing and lifting it off the engine.
2. Clean the engine mating surface before installation.
3. Position the flywheel housing on the engine and secure it with bolts, using link brackets to aid in alignment.
Caterpillar cat 416 d backhoe loader (prefix b2d) service repair manual (b2d0...fjjsekfkksefm
This document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes:
1. Cleaning the flywheel housing and inspecting the crankshaft rear seal for leaks.
2. Heating the ring gear and quickly installing it onto the flywheel.
3. Using guide bolts and a lifting device to position the flywheel, then installing and tightening the bolts.
Caterpillar cat 416 d backhoe loader (prefix b2d) service repair manual (b2d0...fujsjefkskekmm
This document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes:
1. Cleaning the flywheel housing and inspecting the crankshaft rear seal for leaks.
2. Heating the ring gear and quickly installing it on the flywheel.
3. Installing the flywheel using guide bolts and lifting equipment, and tightening the bolts to the specified torque.
4. Removing the crankshaft rear seal housing assembly, which must be replaced if removed.
5. Installing the new crankshaft rear seal housing assembly using a plastic sleeve to protect the seal, and tightening the
Caterpillar cat 416 d backhoe loader (prefix b2d) service repair manual (b2d0...fjjsekkksemm
This document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes:
1. Cleaning and preparing the flywheel housing and crankshaft.
2. Heating the ring gear and quickly installing it on the flywheel.
3. Using guide bolts and lifting brackets to position the flywheel, then tightening the bolts to the specified torque.
4. Checking that the housing assembly is clean before installing the new crankshaft rear seal assembly using setscrews.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
The document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054C engine. It describes using guide bolts and a link bracket to support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing assembly. The new seal assembly is installed with a plastic sleeve to protect the seal lip and set screws are used to secure it to the cylinder block.
The document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054C engine. It describes using guide bolts and a link bracket to support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing assembly. The new seal assembly is installed with a plastic sleeve to protect the seal lip and set screws are used to secure it to the cylinder block.
The document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054C engine. It describes using guide bolts and a link bracket to support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing assembly. The new seal assembly is installed using a plastic sleeve to protect the seal lip and setscrews to secure it to the cylinder block.
The document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054C engine. It describes using guide bolts and a link bracket to support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing assembly. The new seal assembly is installed with a plastic sleeve to protect the seal lip and set screws are used to secure it to the cylinder block.
The document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054C engine. It describes using guide bolts and a link bracket to support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing assembly. The new seal assembly is installed with a plastic sleeve to protect the seal lip and set screws are used to secure it to the cylinder block.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure for the flywheel involves using guide bolts and a link bracket to support the flywheel weight before removing all setscrews. The crankshaft rear seal housing assembly must be replaced as a unit if removed. A plastic sleeve is used to protect the crankshaft rear seal during installation. A puller and spacer are used to remove the crankshaft wear sleeve, which is used to reclaim a worn crankshaft seal surface.
The document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054C engine. It describes using guide bolts and a link bracket to support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the entire housing assembly. The installation procedure involves using a plastic sleeve to protect the seal during installation and aligning the seal housing with the cylinder block before tightening setscrews.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and securing it with mounting bolts. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new one. The procedures are separated into sections for engines with a 14-bolt housing assembly versus a 10-bolt housing assembly. Precise instructions are given for lubricating parts, inserting the seal, aligning components, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f7usuejkdkddm3
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and pressing the pulley onto the crankshaft during installation. Tightening specifications are included for attaching the pulley.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts, lifting the flywheel off, and potentially removing a ring gear. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and explains cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The steps are:
1. Use a drill bit to drill out the lock tabs of the seal.
2. Pry the seal out of the housing with a seal removal tool.
3. Inspect the seal bore and remove any debris before installing the new seal.
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, installing components like seals, spacers, washers, and plugs in reverse order of disassembly. Tools required are listed in tables. Cautions are provided about cleanliness, contamination, misassembly, and applying lubricant to parts.
More Related Content
Similar to Caterpillar Cat 416D Backhoe Loader (Prefix B2D) Service Repair Manual (B2D00001 and up).pdf
The document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054C engine. It describes using guide bolts and a link bracket to support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing assembly. The new seal assembly is installed using a plastic sleeve to protect the seal lip and setscrews to secure it to the cylinder block.
The document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054C engine. It describes using guide bolts and a link bracket to support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing assembly. The new seal assembly is installed with a plastic sleeve to protect the seal lip and set screws are used to secure it to the cylinder block.
The document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054C engine. It describes using guide bolts and a link bracket to support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing assembly. The new seal assembly is installed with a plastic sleeve to protect the seal lip and set screws are used to secure it to the cylinder block.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure for the flywheel involves using guide bolts and a link bracket to support the flywheel weight before removing all setscrews. The crankshaft rear seal housing assembly must be replaced as a unit if removed. A plastic sleeve is used to protect the crankshaft rear seal during installation. A puller and spacer are used to remove the crankshaft wear sleeve, which is used to reclaim a worn crankshaft seal surface.
The document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054C engine. It describes using guide bolts and a link bracket to support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the entire housing assembly. The installation procedure involves using a plastic sleeve to protect the seal during installation and aligning the seal housing with the cylinder block before tightening setscrews.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
Similar to Caterpillar Cat 416D Backhoe Loader (Prefix B2D) Service Repair Manual (B2D00001 and up).pdf (9)
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and securing it with mounting bolts. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new one. The procedures are separated into sections for engines with a 14-bolt housing assembly versus a 10-bolt housing assembly. Precise instructions are given for lubricating parts, inserting the seal, aligning components, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f7usuejkdkddm3
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and pressing the pulley onto the crankshaft during installation. Tightening specifications are included for attaching the pulley.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts, lifting the flywheel off, and potentially removing a ring gear. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and explains cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The steps are:
1. Use a drill bit to drill out the lock tabs of the seal.
2. Pry the seal out of the housing with a seal removal tool.
3. Inspect the seal bore and remove any debris before installing the new seal.
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, installing components like seals, spacers, washers, and plugs in reverse order of disassembly. Tools required are listed in tables. Cautions are provided about cleanliness, contamination, misassembly, and applying lubricant to parts.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f7usuejkdkddm3
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
The document provides assembly instructions for a 345C excavator final drive system. It involves assembling three carrier assemblies that contain planetary gears, installing them into a ring gear housing along with other components like bearing cones and seals. The procedure has 26 steps and requires various tools. It ensures proper bearing preload is achieved and components are cleaned, lubricated and torqued correctly during reassembly.
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416D BACKHOE LOADER B2D
Configuration: 416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i07030444
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Bolt
(1/2 inch - 20 NF by 4 inch)
2
B 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If there
are any oil leaks, refer to this Disassembly and Assembly Manual, "Crankshaft Rear Seal -
Remove" for the correct procedure.
1/3
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00909349
Always wear protective gloves when handling parts that have been
heated.
Note: If ring gear (3) has been removed from flywheel (2). Identify the orientation of ring
gear (3) on the flywheel for the correct positioning when the new ring gear is installed.
2. Heat the ring gear to 250 °C (480 °F) in an oven to install the ring gear onto the flywheel.
Ensure that the orientation of the ring gear is correct and quickly install the ring gear onto
the flywheel.
Note: Do not use a torch to heat the ring gear.
3. Clean flywheel (2) and ring gear (3) when the ring gear has cooled.
2/3
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01148312
4. Install the Tooling (A) on the crankshaft. Install the Tooling (B) and a suitable lifting device
on flywheel (2) and position the flywheel in the flywheel housing. The weight of the
flywheel is approximately 54 kg (119 lb).
5. Install bolts (1) to flywheel (2).
6. Remove Tooling (A). Install the remaining bolts (1) that secure flywheel (2) to the
crankshaft. Tighten the bolts (1) to a torque of 140 N·m (103 lb ft).
7. Check the alignment of flywheel (2) with the crankshaft. Refer to Testing and Adjusting,
"Flywheel - Inspect" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 21 23:20:45 UTC+0800 2019
3/3
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416D BACKHOE LOADER B2D
Configuration: 416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02293665
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00991388
Note: The crankshaft rear seal is nonserviceable. If the crankshaft rear seal is removed, the
complete housing assembly must be replaced.
1. Remove the setscrews (1) from the housing assembly (2).
2. Remove the housing assembly (2) from the cylinder block. Discard the housing assembly
(2).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 21 23:21:42 UTC+0800 2019
2/2
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416D BACKHOE LOADER B2D
Configuration: 416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02293676
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2806 Alignment Tool 1
Note: The crankshaft rear seal and the housing for the crankshaft rear seal are manufactured as a
one-piece assembly. The assembly of the crankshaft rear seal uses ten setscrews in order to fasten
the assembly to the cylinder block.
Note: The following procedure assumes that the crankshaft rear seal is a replacement assembly.
Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the crankshaft
flange before installation.
Note: An installation sleeve (2) is supplied with the new housing assembly. The installation sleeve
must be in place when housing assembly is installed on the crankshaft flange in order to prevent
damage to the crankshaft rear seal during assembly.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 1. Ensure that the crankshaft flange (1) is clean, dry and free from rough metal edges. Ensure
that the face of the cylinder block and the bridge in the crankcase are clean and dry.
Illustration 1 g01148393
2. Remove the packaging from the new assembly of the crankshaft rear seal (3). Ensure that
the plastic sleeve (2) is squarely installed within the seal of the assembly of the crankshaft
rear seal (3). The plastic sleeve (2) is included in order to protect the lip of the seal as the lip
is pushed over the crankshaft flange (1).
Illustration 2 g01004958
Typical example
3. Place the assembly of the crankshaft rear seal (3) over the crankshaft flange (1) and engage
the plastic sleeve (2) onto the crankshaft flange.
2/4
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 4. Ensure that the plastic sleeve (2) is engaged onto the crankshaft flange (1). Push the
assembly of the crankshaft rear seal (3) evenly and push the assembly smoothly onto the
crankshaft flange (1) until the assembly is against the cylinder block. During this process,
the plastic sleeve (2) will be forced out of the assembly of the crankshaft rear seal (3).
Discard the plastic sleeve (2).
5. Rotate the assembly of the crankshaft rear seal (3) in order to align the setscrew holes in the
assembly with the setscrew holes in the rear face of the cylinder block.
6. Install the setscrews (5) in order to position housing assembly (3) to the cylinder block. Do
Not tighten the bolts.
7. Place the Tooling (A) over housing assembly (2). This will center the housing assembly
onto the crankshaft flange (3).
Illustration 3 g01148495
8. Tighten the setscrews (1) in numerical order to a torque of 22 N·m (16 lb ft). Do not tighten
the setscrews (X) at this time.
9. Remove the Tooling (A). Tighten the setscrews (X) to a torque of 22 N·m (16 lb ft).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
3/4
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416D BACKHOE LOADER B2D
Configuration: 416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i05322247
Crankshaft Wear Sleeve (Rear) - Remove
SMCS - 1161-011-ZV
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
242-9955 Puller 1
- Spacer 1
Start By:
A. Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear
Seal - Remove and Install" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Wear sleeves are used to reclaim worn seal surfaces or damaged seal surfaces. Wear sleeves
are not original equipment. The wear sleeve is supplied with a crankshaft rear seal that has a larger
internal diameter than a standard crankshaft rear seal. A standard crankshaft rear seal cannot be
used if a wear sleeve is installed.
1/2
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g02815577
Typical example
1. Use Tooling (A) in order to remove crankshaft wear sleeve (1) from crankshaft (2) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 21 23:23:36 UTC+0800 2019
2/2
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416D BACKHOE LOADER B2D
Configuration: 416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i05764187
Crankshaft Wear Sleeve (Rear) - Install
SMCS - 1161-012-ZV
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
438-3244 Oil Seal Installer 1
8T-0375 Bolt 1
5P-8247 Hard Washer 1
B
438-3245 Oil Seal Locator 1
9U-6172 Bolt 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Wear sleeves are used to reclaim worn seal surfaces or damaged seal surfaces. Wear sleeves
are not original equipment. The wear sleeve is supplied with a crankshaft rear seal that has a larger
internal diameter than a standard crankshaft rear seal. A standard crankshaft rear seal cannot be
used if a wear sleeve is installed.
1. Ensure that the crankshaft is thoroughly clean and dry. Remove any areas of raised damage.
1/2
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 2. Lubricate the inner surface of the crankshaft wear sleeve with clean engine oil.
Illustration 1 g03657723
Sectional view of the crankshaft, the wear sleeve, and the installation tool
3. Use Tooling (A) and Tooling (B) to install the crankshaft wear sleeve, as follows:
a. Align Tooling (B) with the dowels in crankshaft (2) and install Tooling (B) to the
crankshaft. Ensure the correct orientation.
Note: Verify that Tooling (A) will slide freely over Tooling (B).
b. Carefully slide crankshaft wear sleeve (1) over Tooling (B) until the crankshaft wear
sleeve contacts the rear of crankshaft (2).
c. Assemble Tooling (A) to Tooling (B) and install the bolt and the washer. Ensure that
the face of Tooling (A) with the deep counterbore is toward crankshaft wear sleeve
(1).
d. Tighten the bolt until Tooling (A) bottoms out on Tooling (B) in order to pull
crankshaft wear sleeve (1) onto crankshaft (2).
e. Remove Tooling (A) and Tooling (B).
End By:
a. Install the new crankshaft rear seal that was supplied with the crankshaft wear sleeve.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 21 23:24:33 UTC+0800 2019
2/2
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416D BACKHOE LOADER B2D
Configuration: 416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02294250
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. The weight of the flywheel housing (3) is approximately 39 kg (85 lb). Use suitable lifting
equipment to support the flywheel housing (3) while the setscrews (1) are being removed
and while the flywheel housing is being removed.
Illustration 1 g00977367
2. Remove the setscrews (1) from the top of the flywheel housing (3).
3. Attach the Tooling (A) and a suitable lifting device to the flywheel housing (3).
4. Remove the setscrews (2) that attach the flywheel housing (3) to the cylinder block.
5. Remove the flywheel housing (3). If necessary, tap the flywheel housing with a soft faced
hammer in order to separate the flywheel housing from the cylinder block.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
2/4
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the rear face of the cylinder block and the mating surface of the flywheel housing (3).
Illustration 2 g00977388
2. If a felt seal (5) is installed, replace the felt seal. Inspect the dowels (4) in the cylinder block
that align the flywheel housing (3). Replace the dowels, if necessary.
3. The weight of the flywheel housing (3) is approximately 39 kg (85 lb). Use the Tooling (A)
and a suitable lifting device to position the flywheel housing (3) on the dowels (4) that are
on the cylinder block.
4. Install the setscrews (1) that attach the flywheel housing (3) to the cylinder block.
5. Install the setscrews (2) that attach the flywheel housing (3) to the cylinder block.
Tighten the setscrews (1) and the setscrews (2) to the following torque:
M10 "8.8" ... 44 N·m (33 lb ft)
M10 "10.9" ... 63 N·m (46 lb ft)
M12 "8.8" ... 75 N·m (55 lb ft)
M12 "10.9" ... 115 N·m (85 lb ft)
6. Remove Tooling (A) and the lifting device from the flywheel housing.
3/4
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 7. Check the alignment of the flywheel housing with the cylinder block. Refer to Testing and
Adjusting, "Flywheel Housing - Inspect".
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 21 23:25:29 UTC+0800 2019
4/4
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416D BACKHOE LOADER B2D
Configuration: 416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02294252
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
a. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00952102
1. Remove the setscrews (1). Remove the thrust block (2).
2. Remove the pulley (3) from the crankshaft (4).
Installation Procedure
Illustration 2 g00952102
1. Clean the pulley (3) and clean the thrust block (2). Inspect the pulley (3) and the thrust
block (2) for wear and for damage. If necessary, replace any damaged component. Inspect
the area on the pulley (3) that is normally in contact with the crankshaft front seal. If there is
excessive wear then a wear sleeve can be installed. Refer to this Disassembly and Assembly
2/3
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...