The document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals, and housing components.
2. Cleaning all parts thoroughly before assembly.
3. Assembling components in reverse order, applying anti-seize compound and determining correct shim thickness to set bearing preload.
4. Installing new seals using special tools and ensuring seals remain undamaged during assembly.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...uddksemd8ud
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...f7djidksmd3e
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...paws21610697
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. It describes:
1) Disassembling the various components of the final drive by removing bolts, pins, gears, and other parts.
2) Proper cleaning and preparation of parts before assembly.
3) The assembly procedure, including installing seals, bearings, gears and other components in the correct order and orientation. Precise measurements are taken to determine the proper shim thickness.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. It describes:
1) Disassembling the various components of the final drive by removing bolts, pins, gears, and other parts.
2) Properly supporting components with tooling as they are removed to avoid injury.
3) Cleaning all parts thoroughly before assembly.
4) Assembling the components in reverse order, applying anti-seize compound, torqueing bolts, and ensuring proper bearing preload using shims.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...jdjkskmikdkmd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and verifying seal installation. Proper cleaning and torqueing of fasteners is emphasized.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual Instant ...jiuliu14811471
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and verifying seal installation. Proper cleaning and torqueing of fasteners is emphasized.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual Instant ...qianxu35543635
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. It describes:
1) Disassembling the various components of the final drive by removing bolts, pins, gears, and other parts.
2) Properly supporting components with tooling as they are removed to safely handle heavy pieces.
3) Cleaning all parts thoroughly before assembly.
4) Assembling the components in reverse order, applying anti-seize compound and determining the correct number of shims to achieve proper bearing preload.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...uddksemd8ud
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...f7djidksmd3e
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...paws21610697
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. It describes:
1) Disassembling the various components of the final drive by removing bolts, pins, gears, and other parts.
2) Proper cleaning and preparation of parts before assembly.
3) The assembly procedure, including installing seals, bearings, gears and other components in the correct order and orientation. Precise measurements are taken to determine the proper shim thickness.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. It describes:
1) Disassembling the various components of the final drive by removing bolts, pins, gears, and other parts.
2) Properly supporting components with tooling as they are removed to avoid injury.
3) Cleaning all parts thoroughly before assembly.
4) Assembling the components in reverse order, applying anti-seize compound, torqueing bolts, and ensuring proper bearing preload using shims.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...jdjkskmikdkmd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and verifying seal installation. Proper cleaning and torqueing of fasteners is emphasized.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual Instant ...jiuliu14811471
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and verifying seal installation. Proper cleaning and torqueing of fasteners is emphasized.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual Instant ...qianxu35543635
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. It describes:
1) Disassembling the various components of the final drive by removing bolts, pins, gears, and other parts.
2) Properly supporting components with tooling as they are removed to safely handle heavy pieces.
3) Cleaning all parts thoroughly before assembly.
4) Assembling the components in reverse order, applying anti-seize compound and determining the correct number of shims to achieve proper bearing preload.
Caterpillar Cat 365B L Excavator (Prefix 9TZ) Service Repair Manual Instant D...jiuliu14811471
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly process involves removing over 30 individual parts in a specific sequence. Assembly is the reverse of disassembly and requires determining the correct shim thickness between bearings using precise measurements. Special tools are needed and surfaces must be cleaned thoroughly during both processes.
Caterpillar Cat 365B L Excavator (Prefix 9TZ) Service Repair Manual (9TZ00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 365B L Excavator. It describes in detail the 31 steps to disassemble the components of the final drive and the 34 steps to reassemble it. Key parts that are disassembled include the ring gear, carrier assemblies, gears, bearings and seals. The assembly process involves applying anti-seize compound, installing new seals and bearings, and using shims to achieve the correct bearing preload. Precise measurements are taken to determine the number of shims needed.
Caterpillar Cat 365B L Excavator (Prefix 9TZ) Service Repair Manual (9TZ00001...paws21610697
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar Cat 365B L Excavator (Prefix 9TZ) Service Repair Manual Instant D...qianxu35543635
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar Cat 365B L Excavator (Prefix 9TZ) Service Repair Manual (9TZ00001...f7djidksmd3e
This document provides instructions for disassembling and assembling the final drive of a 365B L excavator. It describes in detail the 31 steps to disassemble the components of the final drive, including removing gears, shafts, carriers, and housing pieces. It then lists the 34 steps to reassemble the final drive, applying lubricants and following a process to determine the correct bearing preload using measurements and applied loads. The goal is to fully disassemble and then reassemble the final drive while ensuring all parts are clean and seals are in good condition.
Caterpillar Cat 365B L Excavator (Prefix 9TZ) Service Repair Manual (9TZ00001...uddksemd8ud
This document provides instructions for disassembling and assembling the final drive of a 365B L Excavator. It describes in detail the 31 steps to disassemble the components of the final drive, including removing gears, shafts, bearings, seals and housing pieces. It then lists the 34 steps to reassemble the final drive, applying lubricants and following a process to determine the correct bearing preload and number of shims needed. The goal is to fully disassemble and then reassemble the final drive, ensuring all components are clean and seals are replaced as needed.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
This document provides instructions for disassembling and assembling the final drive of a 365B L Excavator. It describes in detail the 31 steps to disassemble the various components of the final drive, including removing gears, shafts, bearings, seals, and housing pieces. It then describes the 34 steps to reassemble the final drive, including applying lubricants, installing new seals and bearings, attaching housing pieces, and adjusting bearing preload using shims. The goal is to disassemble and reassemble the final drive while keeping parts in their original locations and orienting alignment marks.
Caterpillar Cat 365B L Excavator (Prefix 9TZ) Service Repair Manual (9TZ00001...jdjkskmikdkmd
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar cat 365 b excavator (prefix 9tz) service repair manual (9tz00001 ...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B L excavator. It describes in detail the 31 steps to disassemble the components of the final drive, including removing gears, shafts, carriers, and housing pieces. It then lists the 34 assembly steps, specifying the required tools and explaining how to install components like bearings, seals, gears, and housings back into the final drive. Precautions like cleaning parts and applying lubricants are noted.
Caterpillar cat 365 b l excavator (prefix 9tz) service repair manual (9tz0000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly process involves removing over 30 individual parts in a specific sequence. Assembly is the reverse of disassembly and requires determining the correct shim thickness between bearings using precise measurements. Special tools are needed and surfaces must be cleaned thoroughly during both processes.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly process involves removing over 30 individual parts in a specific sequence. Assembly is the reverse of disassembly and requires determining the correct shim thickness between bearings using precise measurements. Special tools are needed and surfaces must be cleaned thoroughly during both processes.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly process involves removing over 30 individual parts in a specific sequence. Assembly is the reverse of disassembly and requires determining the correct shim thickness between bearings using precise measurements. Special tools are needed and surfaces must be cleaned thoroughly during both processes.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly process involves removing over 30 individual parts in a specific sequence. Assembly is the reverse of disassembly and requires determining the correct shim thickness between bearings using precise measurements. Special tools are needed and surfaces must be cleaned thoroughly during both processes.
Caterpillar Cat 365B and 365B L Excavator (Prefix 9PZ) Service Repair Manual ...shibi1322
The document provides instructions for disassembling and assembling a final drive for an excavator model. It describes 31 steps to disassemble the final drive by removing components like gears, bearings, seals, and housing pieces. It then describes 14 steps to reassemble the final drive, including applying lubricants, setting bearing preloads, and installing seals and gears back into their proper locations and orientations. The overall process involves separating the main housing from the motor housing and precisely reinstalling all parts.
Caterpillar Cat 365B and 365B L Excavator (Prefix 9PZ) Service Repair Manual ...8foskkdjdkdm3e
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly process involves removing over 30 parts including gears, bearings, seals, and housing components. Detailed steps and illustrations are provided for each part. The assembly section outlines cleaning and inspection procedures, and reversing the disassembly steps to reinstall each part in the proper location using anti-seize compound and thread lock as needed. Bearing preload is set using shims determined by measuring gear dimensions under a calibrated press load.
Caterpillar Cat 365B and 365B L Excavator (Prefix 9PZ) Service Repair Manual ...yin9niaojiao
The document provides instructions for disassembling and assembling the final drive of an excavator. It describes 31 steps to disassemble the components of the final drive by removing bolts, gears, bearings, seals, and housing pieces. It then describes 34 steps to reassemble the final drive, including applying lubricants, setting bearing preloads, and installing seals, gears, bearings, and housing components in the reverse order of disassembly. Tools and torque specifications are provided for completing the disassembly and assembly work.
Caterpillar Cat 365B L Excavator (Prefix 9TZ) Service Repair Manual Instant D...jiuliu14811471
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly process involves removing over 30 individual parts in a specific sequence. Assembly is the reverse of disassembly and requires determining the correct shim thickness between bearings using precise measurements. Special tools are needed and surfaces must be cleaned thoroughly during both processes.
Caterpillar Cat 365B L Excavator (Prefix 9TZ) Service Repair Manual (9TZ00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 365B L Excavator. It describes in detail the 31 steps to disassemble the components of the final drive and the 34 steps to reassemble it. Key parts that are disassembled include the ring gear, carrier assemblies, gears, bearings and seals. The assembly process involves applying anti-seize compound, installing new seals and bearings, and using shims to achieve the correct bearing preload. Precise measurements are taken to determine the number of shims needed.
Caterpillar Cat 365B L Excavator (Prefix 9TZ) Service Repair Manual (9TZ00001...paws21610697
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar Cat 365B L Excavator (Prefix 9TZ) Service Repair Manual Instant D...qianxu35543635
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar Cat 365B L Excavator (Prefix 9TZ) Service Repair Manual (9TZ00001...f7djidksmd3e
This document provides instructions for disassembling and assembling the final drive of a 365B L excavator. It describes in detail the 31 steps to disassemble the components of the final drive, including removing gears, shafts, carriers, and housing pieces. It then lists the 34 steps to reassemble the final drive, applying lubricants and following a process to determine the correct bearing preload using measurements and applied loads. The goal is to fully disassemble and then reassemble the final drive while ensuring all parts are clean and seals are in good condition.
Caterpillar Cat 365B L Excavator (Prefix 9TZ) Service Repair Manual (9TZ00001...uddksemd8ud
This document provides instructions for disassembling and assembling the final drive of a 365B L Excavator. It describes in detail the 31 steps to disassemble the components of the final drive, including removing gears, shafts, bearings, seals and housing pieces. It then lists the 34 steps to reassemble the final drive, applying lubricants and following a process to determine the correct bearing preload and number of shims needed. The goal is to fully disassemble and then reassemble the final drive, ensuring all components are clean and seals are replaced as needed.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
This document provides instructions for disassembling and assembling the final drive of a 365B L Excavator. It describes in detail the 31 steps to disassemble the various components of the final drive, including removing gears, shafts, bearings, seals, and housing pieces. It then describes the 34 steps to reassemble the final drive, including applying lubricants, installing new seals and bearings, attaching housing pieces, and adjusting bearing preload using shims. The goal is to disassemble and reassemble the final drive while keeping parts in their original locations and orienting alignment marks.
Caterpillar Cat 365B L Excavator (Prefix 9TZ) Service Repair Manual (9TZ00001...jdjkskmikdkmd
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar cat 365 b excavator (prefix 9tz) service repair manual (9tz00001 ...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B L excavator. It describes in detail the 31 steps to disassemble the components of the final drive, including removing gears, shafts, carriers, and housing pieces. It then lists the 34 assembly steps, specifying the required tools and explaining how to install components like bearings, seals, gears, and housings back into the final drive. Precautions like cleaning parts and applying lubricants are noted.
Caterpillar cat 365 b l excavator (prefix 9tz) service repair manual (9tz0000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly process involves removing over 30 individual parts in a specific sequence. Assembly is the reverse of disassembly and requires determining the correct shim thickness between bearings using precise measurements. Special tools are needed and surfaces must be cleaned thoroughly during both processes.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly process involves removing over 30 individual parts in a specific sequence. Assembly is the reverse of disassembly and requires determining the correct shim thickness between bearings using precise measurements. Special tools are needed and surfaces must be cleaned thoroughly during both processes.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly process involves removing over 30 individual parts in a specific sequence. Assembly is the reverse of disassembly and requires determining the correct shim thickness between bearings using precise measurements. Special tools are needed and surfaces must be cleaned thoroughly during both processes.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly process involves removing over 30 individual parts in a specific sequence. Assembly is the reverse of disassembly and requires determining the correct shim thickness between bearings using precise measurements. Special tools are needed and surfaces must be cleaned thoroughly during both processes.
Caterpillar Cat 365B and 365B L Excavator (Prefix 9PZ) Service Repair Manual ...shibi1322
The document provides instructions for disassembling and assembling a final drive for an excavator model. It describes 31 steps to disassemble the final drive by removing components like gears, bearings, seals, and housing pieces. It then describes 14 steps to reassemble the final drive, including applying lubricants, setting bearing preloads, and installing seals and gears back into their proper locations and orientations. The overall process involves separating the main housing from the motor housing and precisely reinstalling all parts.
Caterpillar Cat 365B and 365B L Excavator (Prefix 9PZ) Service Repair Manual ...8foskkdjdkdm3e
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly process involves removing over 30 parts including gears, bearings, seals, and housing components. Detailed steps and illustrations are provided for each part. The assembly section outlines cleaning and inspection procedures, and reversing the disassembly steps to reinstall each part in the proper location using anti-seize compound and thread lock as needed. Bearing preload is set using shims determined by measuring gear dimensions under a calibrated press load.
Caterpillar Cat 365B and 365B L Excavator (Prefix 9PZ) Service Repair Manual ...yin9niaojiao
The document provides instructions for disassembling and assembling the final drive of an excavator. It describes 31 steps to disassemble the components of the final drive by removing bolts, gears, bearings, seals, and housing pieces. It then describes 34 steps to reassemble the final drive, including applying lubricants, setting bearing preloads, and installing seals, gears, bearings, and housing components in the reverse order of disassembly. Tools and torque specifications are provided for completing the disassembly and assembly work.
Similar to Caterpillar Cat 365B II EXCAVATOR (Prefix JMB) Service Repair Manual (JMB00001 and up).pdf (20)
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 365B II EXCAVATOR JMB
Configuration: 365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine
Disassembly and Assembly
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems
Media Number -RENR1970-10 Publication Date -01/02/2015 Date Updated -16/02/2015
i02001476
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Stand Group 1
B 138-7575 Link Bracket 5
C 1P-1859 Retaining Ring Pliers 1
F 154-6183 Forcing Bolt 3
G 138-7576 Link Bracket 3
Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove" in this
manual.
1. Thoroughly clean the outside of the final drive prior to disassembly.
1/13
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00595985
2. Fasten the final drive to Tooling (A), as shown. Put an alignment mark across the sections
of the final drive for assembly purposes. All parts must be reinstalled in the original
locations. The weight of the final drive is 721 kg (1590 lb).
Illustration 2 g00596007
3. Remove socket head bolts (1) from the final drive cover.
Illustration 3 g00596010
2/13
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 4. Fasten Tooling (B) and a suitable lifting device to cover (2), as shown.
5. Remove bolts (3) and the washers that hold the cover in place.
6. Use a soft faced hammer in order to break the seal between the cover and the ring gear.
Remove the cover. The weight of the cover is approximately 65 kg (145 lb).
Illustration 4 g00596018
7. Remove spacer (4) and the shims from the cover.
8. Remove socket head bolts (5) and ring gear (6) from the cover.
Illustration 5 g00596082
9. Remove sun gear (7). Use two people to remove carrier assembly (8) by lifting upward. The
weight of carrier assembly (8) is approximately 24 kg (55 lb).
3/13
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g00596242
10. Use Tooling (C) in order to remove retaining rings (9) and washers (10) .
Illustration 7 g00596269
11. Remove gears (11) .
Illustration 8 g00596273
12. Remove bearings (12) and spacer (13) .
4/13
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g00596337
13. Remove washers (16). Use suitable Tooling to remove ring (14). Remove gear (15) .
Illustration 10 g00596342
14. Remove spacer (17) .
5/13
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g01035731
15. Fasten Tooling (B) and a suitable lifting device to carrier assembly (18). Remove the carrier
assembly. The weight of the carrier assembly is 68 kg (150 lb).
Illustration 12 g00596442
Illustration 13 g00596446
16. Drive pin (19) inward to shaft (20). Use a soft faced hammer and tap the shaft downward in
order to remove the shaft. Remove gear assembly (21) .
6/13
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00596485
17. Disassemble the gear assembly, as follows: washer (22), bearing (23), gear (24) and washer
(25) .
18. Repeat Steps 16 through 17 for the remaining gear assemblies.
Illustration 15 g00596764
19. Use suitable Tooling to remove ring (26). Remove gear (27) .
7/13
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 16 g00596790
20. Remove spacer (28) .
Illustration 17 g01035733
21. Fasten Tooling (B) and a suitable lifting device to carrier assembly (29). Remove the carrier
assembly (29). The weight of carrier assembly (29) is approximately 106 kg (235 lb).
Illustration 18 g00596816
22. Drive pin (31) inward to shaft (30). Use a soft faced hammer and tap the shaft downward in
order to remove the shaft. Remove gear assembly (32) .
8/13
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 19 g00596823
23. Disassemble the gear assembly, as follows: washer (33), bearing (34), gear (35), bearing
(36) and washer (37) .
24. Repeat Steps 22 through 23 for the remaining gear assemblies.
Illustration 20 g01035734
25. Fasten Tooling (B) and a suitable lifting device to gear (38), as shown. Remove the ring
gear from main housing (39). The weight of the ring gear is approximately 124 kg (275 lb).
9/13
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00596864
26. Remove O-ring (40) from the main housing.
Note: Place wood blocks under the final drive in order to support the motor housing.
Illustration 22 g00596901
27. Remove bolts (41) from gear (42) .
Illustration 23 g00596918
28. Install Tooling (F) in the gear, as shown. Tighten Tooling (F) evenly in order to loosen the
gear. Remove the gear from the motor housing.
10/13
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engin...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 24 g00596927
29. Remove shims (43) from the motor housing.
Note: The inner bearing cones and the outer bearing cones are a slip fit on the motor
housing. The inner bearing cone may stay with either housing during separation.
Illustration 25 g01035735
30. Fasten Tooling (G) and a suitable lifting device to main housing (39), as shown. Separate
the main housing from motor housing (44). The motor housing will rest on the wood blocks.
The weight of main housing (39) is approximately 188 kg (415 lb).
11/13
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engin...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g00596986
31. Remove bearing (45) and the bearing cone from the main housing.
Illustration 27 g00596994
32. Remove Duo-Cone seal (46) from the main housing.
33. Remove bearing cups (47) and (48) from the main housing.
Illustration 28 g00597020
12/13
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engin...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 34. Remove pins (49) .
35. Remove bearing (50) and the bearing cone.
36. Remove Duo-Cone seal (51) from the motor housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 21 01:04:16 UTC+0800 2020
13/13
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engin...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 365B II EXCAVATOR JMB
Configuration: 365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine
Disassembly and Assembly
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems
Media Number -RENR1970-10 Publication Date -01/02/2015 Date Updated -16/02/2015
i02789460
Final Drive - Assemble
SMCS - 4050-016
Assembly procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7575 Link Bracket 5
C 140-7642 Duo-Cone Seal Installer As 1
F 1P-1859 Retaining Ring Pliers 1
G 138-7576 Link Bracket 2
H 5P-3931 Anti-Seize Compound 1
J 9S-3263 Thread Lock Compound 1
K 1U-8846 Gasket Sealant 1
1. Make sure that all parts of the final drive are thoroughly clean and free of dirt and debris
prior to assembly.
Note: Check the condition of all the O-ring seals that are used in the final drive. If any of
the seals are worn or damaged, use new parts for replacement.
2. Reassemble the final drive on Tooling (A) .
1/16
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00599211
3. Apply Tooling (H) to the surfaces that contact the bearing cones. Install the bearing cone
with a press. Raise the temperature of bearing (50) and install bearing (50) .
4. Apply Tooling (H) to the surfaces that contact pins (49) . Install pins (49) .
Illustration 2 g00599224
5. Apply Tooling (H) to the surfaces that contact bearing cups (48) and (47) . Install bearing
cups (48) and (47) .
2/16
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00596986
6. Install bearing (45) and the bearing cone.
Illustration 4 g01035739
7. Attach Tooling (B) and a suitable lifting device to main housing (39) . Install the main
housing on motor housing (44) , as shown.
8. Use the following procedure to determine the bearing preload and the correct number of
shims.
Illustration 5 g00603328
a. Use a depth micrometer in order to measure the step length of the coupling gear (42) .
Take measurements at several different locations around the gear. Compute the
average of the measured dimensions and record the number. Call this dimension (X) .
b. Use a suitable press and a spacer in order to apply a load of 10000 kg (22046 lb) on
the bearings.
c. Rotate the main housing in order to seat the bearing.
d. Reduce the load on the bearings to 3700 ± 370 kg (8157 ± 815 lb).
3/16
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 6 g00603604
e. Maintain the load on the bearings. Use a depth micrometer and measure the distance
between the top face of motor housing and the bearing cone, as shown. Take this
measurement in several locations around the bearing. Compute the average of the
measured dimensions and record the number. Call this dimension (Y) .
f. Determine the correct thickness of the shim pack that will be installed between the
bearing cone and the coupling gear. The shim pack thickness is equal to dimension
(Y) minus dimension (X) . Tolerance for the shim pack is 0.1 mm (0.003 inch).
Note: If two shims are required, install the thinner shim next to the coupling gear
when the coupling gear is installed.
9. Attach Tooling (B) and a suitable lifting device in order to remove the main housing from
the motor housing.
Note: Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contact the seals must be clean and dry. After
installation of the seals, apply clean SAE 30 oil on the contact surfaces of the metal seals.
Illustration 7 g00600071
4/16
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 10. Use Tooling (C) to install Duo-Cone seal (46) in the main housing.
Illustration 8 g00600087
11. Use Tooling (C) to install Duo-Cone seal (51) in the motor housing.
Note: Make sure that the Duo-Cone seals are not scratched or damaged during the assembly
of the main housing or during the assembly of the motor housing. After installation of the
main housing on the motor housing, there will be a small gap between the components. The
gap is caused by the Duo-Cone seals. The gap will be eliminated during installation of the
gear.
Illustration 9 g00596986
12. Install bearing (45) and the bearing cone.
5/16
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 10 g01035739
13. Attach Tooling (B) and a suitable lifting device to main housing (39) . Position main
housing (39) on motor housing (44) . Make sure that the Duo-Cone seals are not scratched
or damaged during installation.
Illustration 11 g00596927
14. Place shims (43) in the correct position on the motor housing. If two shims were required,
put the thinner shim in contact with coupling gear (42) . Make sure that all of the holes in
the components are in alignment with each other.
6/16
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 12 g00596901
15. Put coupling gear (42) in the original position on the motor housing.
16. Apply Tooling (J) on the threads of bolts (41) . Install the bolts to secure coupling gear (42)
in place. Tighten bolts (41) evenly and tighten the bolts in diagonally opposite pairs.
Tighten bolts to a torque of 1600 ± 200 N·m (1180 ± 148 lb ft).
Illustration 13 g00596864
17. Install O-ring seal (40) in the main housing.
Illustration 14 g01035734
18. Thoroughly clean the mating surface of main housing (39) that contacts ring gear (38) .
Apply a bead of Tooling (K) on the mating surface of ring gear (38) . Use Tooling (B) and a
suitable lifting device. Place the ring gear in position on the main housing. Make sure that
the alignment mark on the main housing and the ring gear line up with each other. It may be
necessary to use a soft faced hammer to seat the ring gear on the main housing.
19. Assemble carrier assembly (29) , as follows:
7/16
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 15 g00596823
Illustration 16 g00603856
a. Apply clean SAE 30 oil on bearings (34) and (36) . Install bearings (34) and (36) in
planetary gear (35) .
b. Install thrust washers (33) and (37) on each side of the planetary gear.
c. Install the planetary gear and thrust washers in carrier assembly (29) .
d. Install planetary shaft (30) in carrier (29) and through planetary gear assembly (32) .
Make sure that the spring pin hole in the planetary shaft is in alignment with the
spring pin hole in the carrier.
8/16
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 17 g00513451
e. Install spring pin (31) in the carrier and into the planetary shaft. Make sure that the
spring pin hole in the planetary shaft is in alignment with the spring pin hole in the
carrier.
f. Orient the split in the spring pin (31) horizontally to the carrier. Align the split in the
spring pin to the left or to the right. Make a stake mark on each side of the spring pin
hole in the carrier. This will prevent the spring pin from falling out of the spring pin
hole. Each stake mark should be approximately 1.5 mm (0.06 inch) to 3.00 mm
(0.118 inch) from the outside diameter of the spring pin hole.
g. Repeat Steps 19.a through 19.f in order to install the remaining planetary gears in
carrier (29) .
Illustration 18 g01035740
20. Attach Tooling (B) and a suitable lifting device to carrier assembly (29) . Put the carrier
assembly in position in the ring gear. It may be necessary to move the carrier assembly back
and forth during installation in order to ensure that all gears engage properly.
9/16
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine(S...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 19 g00603929
21. Install spacer (28) on carrier assembly (29) .
22. Assemble carrier assembly (21) , as follows:
Illustration 20 g00596485
a. Apply clean SAE 30 oil on bearing (23) . Install bearing (23) in planetary gear (24) .
b. Install thrust washers (22) and (25) on each side of the planetary gear.
c. Install the thrust washers and the planetary gear in the carrier assembly (21) .
10/16
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engin...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 21 g00596446
d. Install planetary shaft (20) in carrier (21) and through planetary gear assembly (24) .
Make sure that the spring pin hole in the carrier is in alignment with the spring pin
hole in the planetary shaft.
Illustration 22 g00596442
e. Make sure that the spring pin (19) in the planetary shaft is in alignment with the
spring pin hole in the carrier.
11/16
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engin...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 23 g00513451
f. Orient the split in the spring pin (19) horizontally to the carrier. Align the split in the
spring pin to the left or to the right. Make a stake mark on each side of the spring pin
hole in the carrier. This will prevent the spring pin from falling out of the spring pin
hole. Each stake mark should be approximately 1.5 mm (0.06 inch) to 3.00 mm
(0.118 inch) from the outside diameter of the spring pin hole.
g. Repeat Steps 22.a through 22.f in order to install the remaining two planetary gears in
carrier (18) .
Illustration 24 g01035731
23. Attach Tooling (B) and a suitable lifting device to carrier assembly (18) . Position carrier
assembly (18) in ring gear (38) . Move carrier assembly (18) back and forth during the
installation in order to ensure that all gears engage properly.
12/16
365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engin...
2020/11/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...