This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar Cat 365B and 365B L Excavator (Prefix 9PZ) Service Repair Manual ...shibi1322
The document provides instructions for disassembling and assembling a final drive for an excavator model. It describes 31 steps to disassemble the final drive by removing components like gears, bearings, seals, and housing pieces. It then describes 14 steps to reassemble the final drive, including applying lubricants, setting bearing preloads, and installing seals and gears back into their proper locations and orientations. The overall process involves separating the main housing from the motor housing and precisely reinstalling all parts.
Caterpillar Cat 365B and 365B L Excavator (Prefix 9PZ) Service Repair Manual ...8foskkdjdkdm3e
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly process involves removing over 30 parts including gears, bearings, seals, and housing components. Detailed steps and illustrations are provided for each part. The assembly section outlines cleaning and inspection procedures, and reversing the disassembly steps to reinstall each part in the proper location using anti-seize compound and thread lock as needed. Bearing preload is set using shims determined by measuring gear dimensions under a calibrated press load.
Caterpillar Cat 365B and 365B L Excavator (Prefix 9PZ) Service Repair Manual ...yin9niaojiao
The document provides instructions for disassembling and assembling the final drive of an excavator. It describes 31 steps to disassemble the components of the final drive by removing bolts, gears, bearings, seals, and housing pieces. It then describes 34 steps to reassemble the final drive, including applying lubricants, setting bearing preloads, and installing seals, gears, bearings, and housing components in the reverse order of disassembly. Tools and torque specifications are provided for completing the disassembly and assembly work.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. It describes:
1. Removing over 30 components of the final drive including gears, shafts, bearings, seals and housings. Special tools are required to remove many parts.
2. Checking all parts are clean before assembly and replacing any worn seals.
3. Reassembling the final drive by pressing in bearings and seals, installing shims to set proper bearing preload, and attaching housing components using lifting devices due to their heavy weights.
4. Precautions like applying anti-seize compound to mating surfaces and using thread lock on fasteners.
This document provides instructions for disassembling and assembling the final drive of a 365B and 365B L excavator. It outlines 36 steps to disassemble the various components of the final drive using specialized tools. These include removing gears, shafts, bearings, seals and housing pieces. It then describes the 8 assembly steps, which involve pressing components in place with tools, installing new seals, and determining the correct shim thickness using micrometer measurements to set the proper bearing preload. Precautions like cleaning parts and applying anti-seize compound are noted.
This document provides instructions for disassembling and assembling a final drive for an excavator model. It describes in detail how to disassemble the various components of the final drive by removing bolts, gears, shafts, and other parts. The assembly process is described in reverse order and includes applying lubricants and installing seals, bearings, and other components back into their original positions. Precise measurements and shim thicknesses are required to set proper bearing preload.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...uddksemd8ud
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...f7djidksmd3e
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B and 365B L Excavator (Prefix 9PZ) Service Repair Manual ...shibi1322
The document provides instructions for disassembling and assembling a final drive for an excavator model. It describes 31 steps to disassemble the final drive by removing components like gears, bearings, seals, and housing pieces. It then describes 14 steps to reassemble the final drive, including applying lubricants, setting bearing preloads, and installing seals and gears back into their proper locations and orientations. The overall process involves separating the main housing from the motor housing and precisely reinstalling all parts.
Caterpillar Cat 365B and 365B L Excavator (Prefix 9PZ) Service Repair Manual ...8foskkdjdkdm3e
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly process involves removing over 30 parts including gears, bearings, seals, and housing components. Detailed steps and illustrations are provided for each part. The assembly section outlines cleaning and inspection procedures, and reversing the disassembly steps to reinstall each part in the proper location using anti-seize compound and thread lock as needed. Bearing preload is set using shims determined by measuring gear dimensions under a calibrated press load.
Caterpillar Cat 365B and 365B L Excavator (Prefix 9PZ) Service Repair Manual ...yin9niaojiao
The document provides instructions for disassembling and assembling the final drive of an excavator. It describes 31 steps to disassemble the components of the final drive by removing bolts, gears, bearings, seals, and housing pieces. It then describes 34 steps to reassemble the final drive, including applying lubricants, setting bearing preloads, and installing seals, gears, bearings, and housing components in the reverse order of disassembly. Tools and torque specifications are provided for completing the disassembly and assembly work.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. It describes:
1. Removing over 30 components of the final drive including gears, shafts, bearings, seals and housings. Special tools are required to remove many parts.
2. Checking all parts are clean before assembly and replacing any worn seals.
3. Reassembling the final drive by pressing in bearings and seals, installing shims to set proper bearing preload, and attaching housing components using lifting devices due to their heavy weights.
4. Precautions like applying anti-seize compound to mating surfaces and using thread lock on fasteners.
This document provides instructions for disassembling and assembling the final drive of a 365B and 365B L excavator. It outlines 36 steps to disassemble the various components of the final drive using specialized tools. These include removing gears, shafts, bearings, seals and housing pieces. It then describes the 8 assembly steps, which involve pressing components in place with tools, installing new seals, and determining the correct shim thickness using micrometer measurements to set the proper bearing preload. Precautions like cleaning parts and applying anti-seize compound are noted.
This document provides instructions for disassembling and assembling a final drive for an excavator model. It describes in detail how to disassemble the various components of the final drive by removing bolts, gears, shafts, and other parts. The assembly process is described in reverse order and includes applying lubricants and installing seals, bearings, and other components back into their original positions. Precise measurements and shim thicknesses are required to set proper bearing preload.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...uddksemd8ud
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...f7djidksmd3e
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent leaks.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and more. Technicians are advised to clean all parts thoroughly, replace all O-rings and seals, and ensure components are reinstalled in their original locations and orientations. Proper assembly helps prevent contamination and failures.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...f7djidksmd3e
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. It outlines:
1) The required tools and removal procedure for the rear gear group which involves removing bolts, seals, gears, bushings and bearings.
2) The installation procedure for the rear gear group which specifies cleaning, applying lubricant and torque specifications for installing the components in reverse order of removal.
3) The removal procedure for the flywheel which requires attaching lifting equipment and removing bolts and ring gear.
4) The installation procedure for the flywheel which involves heating components, applying threadlocker and torque specifications.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and pins. Special tools are required for tasks like installing seals. Technicians are advised to clean all parts, replace all seals and O-rings, and correct any conditions that caused prior failures.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...f7djidksmd3e
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and sensors. The cylinder head is then removed using lifting equipment due to its weight of 135 kg. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper specification. Special tools and repair kits are listed for tasks such as tapping threads and installing Helicoil inserts if head bolt threads are damaged.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f7djidksmd3e
The document provides instructions to disassemble a swing drive for a 345B II MH excavator. Key steps include:
1. Draining the oil and removing covers and gears to access the internal components.
2. Using punches and hammers to remove pins holding planetary gears to disassemble the carrier assembly.
3. Removing the ring gear, carrier assembly, and other internal parts which require multiple people due to weights over 35 kg.
The purpose is to fully disassemble the swing drive to facilitate repair or replacement of internal components.
Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual (FEE0000...f7djidksmd3e
This document provides instructions for assembling the swing drive of a 345B II excavator. Key steps include:
1. Cleaning and inspecting all parts before assembly.
2. Applying anti-seize compound and grease to bearings and installing them into the swing drive housing along with the pinion shaft and bearing cage.
3. Heating and pressing bearings onto the pinion shaft and installing the assembly into the swing drive housing using a press.
4. Temporarily installing bolts to hold the bearing cage aligned with the housing. The instructions provide details on lubricants to use and proper positioning of parts.
The document provides instructions for disassembling a piston motor (hydraulic fan) with the following key steps:
1. Remove the head and internal components like seals, plates, and bearings.
2. Extract the pistons, retainer, and bearings from the housing.
3. Use specialty tools to remove the retaining ring and springs, allowing removal of the swashplate and shaft.
Proper safety precautions and cleaning of parts is emphasized before disassembly.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...f7djidksmd3e
The document provides instructions to remove the rear power take-off (RPTO) from a Caterpillar C9.3 engine. The steps are:
1. Remove the flywheel housing.
2. Remove the rear cover and gasket.
3. Remove the rear power take-off (RPTO) and O-ring seal.
This document provides instructions for disassembling and assembling the travel motor on Caterpillar 345B and 345B L Excavator models. It lists required tools and parts and provides 32 numbered steps to fully disassemble the travel motor by removing components like brackets, covers, pistons, plates, seals, and housing pieces. Illustrations accompany each step to show how to position the motor and parts for disassembly and reassembly. Safety notices are also included to handle parts and fluids properly.
Caterpillar Cat 340D2 L Excavator (Prefix HHK) Service Repair Manual (HHK0000...f7djidksmd3e
The document provides instructions for disassembling the final drive of an excavator model 340D2 L. It describes 25 steps to remove components such as gears, shafts, seals, bearings and housings. Various tools are required including link brackets and forcing bolts to compress springs. Personal protective equipment is recommended as parts can be propelled by released spring forces. The total weight of the final drive assembly is approximately 550 kg.
Caterpillar Cat 340F L LRE Excavator (Prefix YBF) Service Repair Manual (YBF0...f7djidksmd3e
This document provides the disassembly and assembly procedures for the travel motor on a 340F L LRE excavator. It includes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. The 27 steps to assemble list installing these same components in reverse order and include notes about lubrication, alignment and torque specifications. Required tools are listed for both procedures.
The document provides instructions for removing and installing an engine oil filter base on a 336D LN excavator. It describes:
1) Removing various connectors, seals, valves, and plugs from the engine oil filter base during disassembly.
2) Assembling the engine oil filter base by installing the parts in reverse order of removal.
3) Installing the engine oil filter base on the engine, including attaching hoses and bolts.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and provides details on lubricating parts and ensuring proper alignment of components like the cam plate and brake piston. Special tools are required for tasks like removing the rotating assembly and installing seals and bearings.
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f7djidksmd3e
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It lists required tools and outlines a 15 step procedure for removing the swivel that includes disconnecting hoses, removing bolts and other fasteners, and using lifting devices. A 7 step disassembly procedure is also provided which involves cleaning, positioning, and separating the swivel's outer housing and rotor components using bolts, washers, and specialized tooling. Personal protective equipment is recommended when handling fluids.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent leaks.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and more. Technicians are advised to clean all parts thoroughly, replace all O-rings and seals, and ensure components are reinstalled in their original locations and orientations. Proper assembly helps prevent contamination and failures.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...f7djidksmd3e
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. It outlines:
1) The required tools and removal procedure for the rear gear group which involves removing bolts, seals, gears, bushings and bearings.
2) The installation procedure for the rear gear group which specifies cleaning, applying lubricant and torque specifications for installing the components in reverse order of removal.
3) The removal procedure for the flywheel which requires attaching lifting equipment and removing bolts and ring gear.
4) The installation procedure for the flywheel which involves heating components, applying threadlocker and torque specifications.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and pins. Special tools are required for tasks like installing seals. Technicians are advised to clean all parts, replace all seals and O-rings, and correct any conditions that caused prior failures.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...f7djidksmd3e
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and sensors. The cylinder head is then removed using lifting equipment due to its weight of 135 kg. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper specification. Special tools and repair kits are listed for tasks such as tapping threads and installing Helicoil inserts if head bolt threads are damaged.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f7djidksmd3e
The document provides instructions to disassemble a swing drive for a 345B II MH excavator. Key steps include:
1. Draining the oil and removing covers and gears to access the internal components.
2. Using punches and hammers to remove pins holding planetary gears to disassemble the carrier assembly.
3. Removing the ring gear, carrier assembly, and other internal parts which require multiple people due to weights over 35 kg.
The purpose is to fully disassemble the swing drive to facilitate repair or replacement of internal components.
Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual (FEE0000...f7djidksmd3e
This document provides instructions for assembling the swing drive of a 345B II excavator. Key steps include:
1. Cleaning and inspecting all parts before assembly.
2. Applying anti-seize compound and grease to bearings and installing them into the swing drive housing along with the pinion shaft and bearing cage.
3. Heating and pressing bearings onto the pinion shaft and installing the assembly into the swing drive housing using a press.
4. Temporarily installing bolts to hold the bearing cage aligned with the housing. The instructions provide details on lubricants to use and proper positioning of parts.
The document provides instructions for disassembling a piston motor (hydraulic fan) with the following key steps:
1. Remove the head and internal components like seals, plates, and bearings.
2. Extract the pistons, retainer, and bearings from the housing.
3. Use specialty tools to remove the retaining ring and springs, allowing removal of the swashplate and shaft.
Proper safety precautions and cleaning of parts is emphasized before disassembly.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...f7djidksmd3e
The document provides instructions to remove the rear power take-off (RPTO) from a Caterpillar C9.3 engine. The steps are:
1. Remove the flywheel housing.
2. Remove the rear cover and gasket.
3. Remove the rear power take-off (RPTO) and O-ring seal.
This document provides instructions for disassembling and assembling the travel motor on Caterpillar 345B and 345B L Excavator models. It lists required tools and parts and provides 32 numbered steps to fully disassemble the travel motor by removing components like brackets, covers, pistons, plates, seals, and housing pieces. Illustrations accompany each step to show how to position the motor and parts for disassembly and reassembly. Safety notices are also included to handle parts and fluids properly.
Caterpillar Cat 340D2 L Excavator (Prefix HHK) Service Repair Manual (HHK0000...f7djidksmd3e
The document provides instructions for disassembling the final drive of an excavator model 340D2 L. It describes 25 steps to remove components such as gears, shafts, seals, bearings and housings. Various tools are required including link brackets and forcing bolts to compress springs. Personal protective equipment is recommended as parts can be propelled by released spring forces. The total weight of the final drive assembly is approximately 550 kg.
Caterpillar Cat 340F L LRE Excavator (Prefix YBF) Service Repair Manual (YBF0...f7djidksmd3e
This document provides the disassembly and assembly procedures for the travel motor on a 340F L LRE excavator. It includes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. The 27 steps to assemble list installing these same components in reverse order and include notes about lubrication, alignment and torque specifications. Required tools are listed for both procedures.
The document provides instructions for removing and installing an engine oil filter base on a 336D LN excavator. It describes:
1) Removing various connectors, seals, valves, and plugs from the engine oil filter base during disassembly.
2) Assembling the engine oil filter base by installing the parts in reverse order of removal.
3) Installing the engine oil filter base on the engine, including attaching hoses and bolts.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and provides details on lubricating parts and ensuring proper alignment of components like the cam plate and brake piston. Special tools are required for tasks like removing the rotating assembly and installing seals and bearings.
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f7djidksmd3e
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It lists required tools and outlines a 15 step procedure for removing the swivel that includes disconnecting hoses, removing bolts and other fasteners, and using lifting devices. A 7 step disassembly procedure is also provided which involves cleaning, positioning, and separating the swivel's outer housing and rotor components using bolts, washers, and specialized tooling. Personal protective equipment is recommended when handling fluids.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 365B EXCAVATOR 9TZ
Configuration: 365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine
Disassembly and Assembly
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems
Media Number -RENR1970-10 Publication Date -01/02/2015 Date Updated -16/02/2015
i02001476
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Stand Group 1
B 138-7575 Link Bracket 5
C 1P-1859 Retaining Ring Pliers 1
F 154-6183 Forcing Bolt 3
G 138-7576 Link Bracket 3
Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove" in this
manual.
1. Thoroughly clean the outside of the final drive prior to disassembly.
1/13
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00595985
2. Fasten the final drive to Tooling (A), as shown. Put an alignment mark across the sections
of the final drive for assembly purposes. All parts must be reinstalled in the original
locations. The weight of the final drive is 721 kg (1590 lb).
Illustration 2 g00596007
3. Remove socket head bolts (1) from the final drive cover.
Illustration 3 g00596010
2/13
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 4. Fasten Tooling (B) and a suitable lifting device to cover (2), as shown.
5. Remove bolts (3) and the washers that hold the cover in place.
6. Use a soft faced hammer in order to break the seal between the cover and the ring gear.
Remove the cover. The weight of the cover is approximately 65 kg (145 lb).
Illustration 4 g00596018
7. Remove spacer (4) and the shims from the cover.
8. Remove socket head bolts (5) and ring gear (6) from the cover.
Illustration 5 g00596082
9. Remove sun gear (7). Use two people to remove carrier assembly (8) by lifting upward. The
weight of carrier assembly (8) is approximately 24 kg (55 lb).
3/13
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g00596242
10. Use Tooling (C) in order to remove retaining rings (9) and washers (10) .
Illustration 7 g00596269
11. Remove gears (11) .
Illustration 8 g00596273
12. Remove bearings (12) and spacer (13) .
4/13
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g00596337
13. Remove washers (16). Use suitable Tooling to remove ring (14). Remove gear (15) .
Illustration 10 g00596342
14. Remove spacer (17) .
5/13
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g01035731
15. Fasten Tooling (B) and a suitable lifting device to carrier assembly (18). Remove the carrier
assembly. The weight of the carrier assembly is 68 kg (150 lb).
Illustration 12 g00596442
Illustration 13 g00596446
16. Drive pin (19) inward to shaft (20). Use a soft faced hammer and tap the shaft downward in
order to remove the shaft. Remove gear assembly (21) .
6/13
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00596485
17. Disassemble the gear assembly, as follows: washer (22), bearing (23), gear (24) and washer
(25) .
18. Repeat Steps 16 through 17 for the remaining gear assemblies.
Illustration 15 g00596764
19. Use suitable Tooling to remove ring (26). Remove gear (27) .
7/13
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 16 g00596790
20. Remove spacer (28) .
Illustration 17 g01035733
21. Fasten Tooling (B) and a suitable lifting device to carrier assembly (29). Remove the carrier
assembly (29). The weight of carrier assembly (29) is approximately 106 kg (235 lb).
Illustration 18 g00596816
22. Drive pin (31) inward to shaft (30). Use a soft faced hammer and tap the shaft downward in
order to remove the shaft. Remove gear assembly (32) .
8/13
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 19 g00596823
23. Disassemble the gear assembly, as follows: washer (33), bearing (34), gear (35), bearing
(36) and washer (37) .
24. Repeat Steps 22 through 23 for the remaining gear assemblies.
Illustration 20 g01035734
25. Fasten Tooling (B) and a suitable lifting device to gear (38), as shown. Remove the ring
gear from main housing (39). The weight of the ring gear is approximately 124 kg (275 lb).
9/13
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00596864
26. Remove O-ring (40) from the main housing.
Note: Place wood blocks under the final drive in order to support the motor housing.
Illustration 22 g00596901
27. Remove bolts (41) from gear (42) .
Illustration 23 g00596918
28. Install Tooling (F) in the gear, as shown. Tighten Tooling (F) evenly in order to loosen the
gear. Remove the gear from the motor housing.
10/13
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEB...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 24 g00596927
29. Remove shims (43) from the motor housing.
Note: The inner bearing cones and the outer bearing cones are a slip fit on the motor
housing. The inner bearing cone may stay with either housing during separation.
Illustration 25 g01035735
30. Fasten Tooling (G) and a suitable lifting device to main housing (39), as shown. Separate
the main housing from motor housing (44). The motor housing will rest on the wood blocks.
The weight of main housing (39) is approximately 188 kg (415 lb).
11/13
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEB...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g00596986
31. Remove bearing (45) and the bearing cone from the main housing.
Illustration 27 g00596994
32. Remove Duo-Cone seal (46) from the main housing.
33. Remove bearing cups (47) and (48) from the main housing.
Illustration 28 g00597020
12/13
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEB...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 34. Remove pins (49) .
35. Remove bearing (50) and the bearing cone.
36. Remove Duo-Cone seal (51) from the motor housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 10 15:59:32 UTC+0800 2020
13/13
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEB...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 365B EXCAVATOR 9TZ
Configuration: 365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine
Disassembly and Assembly
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems
Media Number -RENR1970-10 Publication Date -01/02/2015 Date Updated -16/02/2015
i02789460
Final Drive - Assemble
SMCS - 4050-016
Assembly procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7575 Link Bracket 5
C 140-7642 Duo-Cone Seal Installer As 1
F 1P-1859 Retaining Ring Pliers 1
G 138-7576 Link Bracket 2
H 5P-3931 Anti-Seize Compound 1
J 9S-3263 Thread Lock Compound 1
K 1U-8846 Gasket Sealant 1
1. Make sure that all parts of the final drive are thoroughly clean and free of dirt and debris
prior to assembly.
Note: Check the condition of all the O-ring seals that are used in the final drive. If any of
the seals are worn or damaged, use new parts for replacement.
2. Reassemble the final drive on Tooling (A) .
1/16
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00599211
3. Apply Tooling (H) to the surfaces that contact the bearing cones. Install the bearing cone
with a press. Raise the temperature of bearing (50) and install bearing (50) .
4. Apply Tooling (H) to the surfaces that contact pins (49) . Install pins (49) .
Illustration 2 g00599224
5. Apply Tooling (H) to the surfaces that contact bearing cups (48) and (47) . Install bearing
cups (48) and (47) .
2/16
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00596986
6. Install bearing (45) and the bearing cone.
Illustration 4 g01035739
7. Attach Tooling (B) and a suitable lifting device to main housing (39) . Install the main
housing on motor housing (44) , as shown.
8. Use the following procedure to determine the bearing preload and the correct number of
shims.
Illustration 5 g00603328
a. Use a depth micrometer in order to measure the step length of the coupling gear (42) .
Take measurements at several different locations around the gear. Compute the
average of the measured dimensions and record the number. Call this dimension (X) .
b. Use a suitable press and a spacer in order to apply a load of 10000 kg (22046 lb) on
the bearings.
c. Rotate the main housing in order to seat the bearing.
d. Reduce the load on the bearings to 3700 ± 370 kg (8157 ± 815 lb).
3/16
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 6 g00603604
e. Maintain the load on the bearings. Use a depth micrometer and measure the distance
between the top face of motor housing and the bearing cone, as shown. Take this
measurement in several locations around the bearing. Compute the average of the
measured dimensions and record the number. Call this dimension (Y) .
f. Determine the correct thickness of the shim pack that will be installed between the
bearing cone and the coupling gear. The shim pack thickness is equal to dimension
(Y) minus dimension (X) . Tolerance for the shim pack is 0.1 mm (0.003 inch).
Note: If two shims are required, install the thinner shim next to the coupling gear
when the coupling gear is installed.
9. Attach Tooling (B) and a suitable lifting device in order to remove the main housing from
the motor housing.
Note: Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contact the seals must be clean and dry. After
installation of the seals, apply clean SAE 30 oil on the contact surfaces of the metal seals.
Illustration 7 g00600071
4/16
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 10. Use Tooling (C) to install Duo-Cone seal (46) in the main housing.
Illustration 8 g00600087
11. Use Tooling (C) to install Duo-Cone seal (51) in the motor housing.
Note: Make sure that the Duo-Cone seals are not scratched or damaged during the assembly
of the main housing or during the assembly of the motor housing. After installation of the
main housing on the motor housing, there will be a small gap between the components. The
gap is caused by the Duo-Cone seals. The gap will be eliminated during installation of the
gear.
Illustration 9 g00596986
12. Install bearing (45) and the bearing cone.
5/16
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 10 g01035739
13. Attach Tooling (B) and a suitable lifting device to main housing (39) . Position main
housing (39) on motor housing (44) . Make sure that the Duo-Cone seals are not scratched
or damaged during installation.
Illustration 11 g00596927
14. Place shims (43) in the correct position on the motor housing. If two shims were required,
put the thinner shim in contact with coupling gear (42) . Make sure that all of the holes in
the components are in alignment with each other.
6/16
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 12 g00596901
15. Put coupling gear (42) in the original position on the motor housing.
16. Apply Tooling (J) on the threads of bolts (41) . Install the bolts to secure coupling gear (42)
in place. Tighten bolts (41) evenly and tighten the bolts in diagonally opposite pairs.
Tighten bolts to a torque of 1600 ± 200 N·m (1180 ± 148 lb ft).
Illustration 13 g00596864
17. Install O-ring seal (40) in the main housing.
Illustration 14 g01035734
18. Thoroughly clean the mating surface of main housing (39) that contacts ring gear (38) .
Apply a bead of Tooling (K) on the mating surface of ring gear (38) . Use Tooling (B) and a
suitable lifting device. Place the ring gear in position on the main housing. Make sure that
the alignment mark on the main housing and the ring gear line up with each other. It may be
necessary to use a soft faced hammer to seat the ring gear on the main housing.
19. Assemble carrier assembly (29) , as follows:
7/16
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 15 g00596823
Illustration 16 g00603856
a. Apply clean SAE 30 oil on bearings (34) and (36) . Install bearings (34) and (36) in
planetary gear (35) .
b. Install thrust washers (33) and (37) on each side of the planetary gear.
c. Install the planetary gear and thrust washers in carrier assembly (29) .
d. Install planetary shaft (30) in carrier (29) and through planetary gear assembly (32) .
Make sure that the spring pin hole in the planetary shaft is in alignment with the
spring pin hole in the carrier.
8/16
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 17 g00513451
e. Install spring pin (31) in the carrier and into the planetary shaft. Make sure that the
spring pin hole in the planetary shaft is in alignment with the spring pin hole in the
carrier.
f. Orient the split in the spring pin (31) horizontally to the carrier. Align the split in the
spring pin to the left or to the right. Make a stake mark on each side of the spring pin
hole in the carrier. This will prevent the spring pin from falling out of the spring pin
hole. Each stake mark should be approximately 1.5 mm (0.06 inch) to 3.00 mm
(0.118 inch) from the outside diameter of the spring pin hole.
g. Repeat Steps 19.a through 19.f in order to install the remaining planetary gears in
carrier (29) .
Illustration 18 g01035740
20. Attach Tooling (B) and a suitable lifting device to carrier assembly (29) . Put the carrier
assembly in position in the ring gear. It may be necessary to move the carrier assembly back
and forth during installation in order to ensure that all gears engage properly.
9/16
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEBP2...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 19 g00603929
21. Install spacer (28) on carrier assembly (29) .
22. Assemble carrier assembly (21) , as follows:
Illustration 20 g00596485
a. Apply clean SAE 30 oil on bearing (23) . Install bearing (23) in planetary gear (24) .
b. Install thrust washers (22) and (25) on each side of the planetary gear.
c. Install the thrust washers and the planetary gear in the carrier assembly (21) .
10/16
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEB...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 21 g00596446
d. Install planetary shaft (20) in carrier (21) and through planetary gear assembly (24) .
Make sure that the spring pin hole in the carrier is in alignment with the spring pin
hole in the planetary shaft.
Illustration 22 g00596442
e. Make sure that the spring pin (19) in the planetary shaft is in alignment with the
spring pin hole in the carrier.
11/16
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEB...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 23 g00513451
f. Orient the split in the spring pin (19) horizontally to the carrier. Align the split in the
spring pin to the left or to the right. Make a stake mark on each side of the spring pin
hole in the carrier. This will prevent the spring pin from falling out of the spring pin
hole. Each stake mark should be approximately 1.5 mm (0.06 inch) to 3.00 mm
(0.118 inch) from the outside diameter of the spring pin hole.
g. Repeat Steps 22.a through 22.f in order to install the remaining two planetary gears in
carrier (18) .
Illustration 24 g01035731
23. Attach Tooling (B) and a suitable lifting device to carrier assembly (18) . Position carrier
assembly (18) in ring gear (38) . Move carrier assembly (18) back and forth during the
installation in order to ensure that all gears engage properly.
12/16
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEB...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 25 g00596342
24. Install spacer (17) .
25. Assemble carrier assembly (8) , as follows:
Illustration 26 g00596337
a. Install washers (16) and gear (15) . Use suitable Tooling to install ring (14) .
Illustration 27 g00596273
13/16
365B L Excavators 9TZ00001-UP (MACHINE) POWERED BY 3196 Engine(SEB...
2020/12/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...