1) The document provides instructions for removing and installing various components of a C13 engine, including the electronic unit injector, electronic unit injector sleeve, turbocharger, exhaust balance solenoid valve, and air control valve.
2) The procedures include disconnecting fuel lines and electrical connections, draining coolant, and removing mounting bolts or nuts using various specialized tools before removing the components.
3) Reinstallation involves cleaning components, applying sealant or lubricant, and reconnecting lines and electrical connections before tightening fasteners to the specified torques.
Caterpillar cat 352 f excavator (prefix rbf) service repair manual (rbf00001 ...fjsjjekdkme
1) The document provides instructions for removing and installing various components of a C13 engine, including the electronic unit injector, electronic unit injector sleeve, turbocharger, exhaust balance solenoid valve, and air control valve.
2) The procedures include disconnecting fuel lines and electrical connections, draining coolant, and removing mounting bolts or nuts to separate components from the engine.
3) Reinstallation involves cleaning components, applying lubricant or sealant, and reconnecting lines and electrical connectors before tightening fasteners to the specified torques.
Caterpillar cat 272 d xhp skid steer loader (prefix etl) service repair manua...ufjjsjekdkemme
The document provides instructions for removing and installing various engine components on a 272D XHP Skid Steer Loader including the fuel injection pump, electronic unit injectors, turbocharger, and mass air flow pressure sensor. The procedures note required tools and safety precautions, and describe disconnecting fuel lines and electrical connections, loosening mounting hardware, and installing new seals before reinstalling components in the reverse order of removal. Torque specifications are provided for tightening fasteners.
Caterpillar cat d11 n track type tractor (prefix 4hk) service repair manual (...fjkskmmdmme
The document provides instructions for disassembling the cylinder head of a D11N track-type tractor. The procedures include removing the inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
Caterpillar cat 321 d lcr excavator (prefix mpg) service repair manual (mpg00...ufdjjsekkmdme
1. The document provides instructions for removing and installing an electronic unit injector, turbocharger, and exhaust manifold on a Caterpillar 321D LCR excavator.
2. The electronic unit injector removal procedure involves disconnecting harness assemblies and fuel lines before using a pry bar to remove the injector. Proper identification of parts is important.
3. Turbocharger removal requires disconnecting tubes, hoses and nuts before the turbocharger can be lifted off. Individual turbocharger components like the turbine housing and compressor housing are also removable.
4. Exhaust manifold removal is dependent on first removing the turbocharger. Cleanliness is emphasized throughout the procedures.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 8001 and up)fjskekdmjekm
This document provides specifications and layout diagrams for a wheel loader. It includes:
1. Specifications such as operating weight, tipping load, engine details, and dimensions.
2. Layout diagrams showing the location of major components such as the bucket, lights, engine, radiator, exhaust filter, and hydraulic components.
3. Details of electrical component locations in and around the cab, including switches, controllers, and sensors.
The document provides technical information on the configuration and specifications of a wheel loader to support maintenance and repair work. Diagrams identify key parts and their locations on the machine.
Caterpillar cat 320 track type excavator (prefix 1 kl) service repair manual ...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and valve seals on Caterpillar 3064 and 3066 engines. The procedures include using various specialty tools to compress springs, extract components, and properly seat new parts. Technicians are advised to keep components clean and lubricate parts during installation.
Caterpillar cat 235 c excavator (prefix 5af) service repair manual (5af00001 ...uudfjjjskkemmd
1) The document provides instructions for removing and installing a fuel filter base and removing a fuel transfer pump from a Caterpillar 235C excavator.
2) The fuel filter base removal instructions include disconnecting fuel lines and removing bolts and the base. Installation is the reverse.
3) Removing the fuel transfer pump involves turning off fuel supply, disconnecting lines, and removing bolts to access the pump.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes:
1) Removing the flywheel using a lifting device and removing bolts, then removing the flywheel ring gear if necessary.
2) Installing the flywheel ring gear if it was removed by heating it and positioning it on the flywheel, then installing the flywheel using bolts and a lifting device.
3) Removing the crankshaft rear seal by removing housing bolts and pulling out the seal, gasket and housing.
4) Installing the new crankshaft rear seal using a installer tool and pressing the seal
Caterpillar cat 352 f excavator (prefix rbf) service repair manual (rbf00001 ...fjsjjekdkme
1) The document provides instructions for removing and installing various components of a C13 engine, including the electronic unit injector, electronic unit injector sleeve, turbocharger, exhaust balance solenoid valve, and air control valve.
2) The procedures include disconnecting fuel lines and electrical connections, draining coolant, and removing mounting bolts or nuts to separate components from the engine.
3) Reinstallation involves cleaning components, applying lubricant or sealant, and reconnecting lines and electrical connectors before tightening fasteners to the specified torques.
Caterpillar cat 272 d xhp skid steer loader (prefix etl) service repair manua...ufjjsjekdkemme
The document provides instructions for removing and installing various engine components on a 272D XHP Skid Steer Loader including the fuel injection pump, electronic unit injectors, turbocharger, and mass air flow pressure sensor. The procedures note required tools and safety precautions, and describe disconnecting fuel lines and electrical connections, loosening mounting hardware, and installing new seals before reinstalling components in the reverse order of removal. Torque specifications are provided for tightening fasteners.
Caterpillar cat d11 n track type tractor (prefix 4hk) service repair manual (...fjkskmmdmme
The document provides instructions for disassembling the cylinder head of a D11N track-type tractor. The procedures include removing the inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
Caterpillar cat 321 d lcr excavator (prefix mpg) service repair manual (mpg00...ufdjjsekkmdme
1. The document provides instructions for removing and installing an electronic unit injector, turbocharger, and exhaust manifold on a Caterpillar 321D LCR excavator.
2. The electronic unit injector removal procedure involves disconnecting harness assemblies and fuel lines before using a pry bar to remove the injector. Proper identification of parts is important.
3. Turbocharger removal requires disconnecting tubes, hoses and nuts before the turbocharger can be lifted off. Individual turbocharger components like the turbine housing and compressor housing are also removable.
4. Exhaust manifold removal is dependent on first removing the turbocharger. Cleanliness is emphasized throughout the procedures.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 8001 and up)fjskekdmjekm
This document provides specifications and layout diagrams for a wheel loader. It includes:
1. Specifications such as operating weight, tipping load, engine details, and dimensions.
2. Layout diagrams showing the location of major components such as the bucket, lights, engine, radiator, exhaust filter, and hydraulic components.
3. Details of electrical component locations in and around the cab, including switches, controllers, and sensors.
The document provides technical information on the configuration and specifications of a wheel loader to support maintenance and repair work. Diagrams identify key parts and their locations on the machine.
Caterpillar cat 320 track type excavator (prefix 1 kl) service repair manual ...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and valve seals on Caterpillar 3064 and 3066 engines. The procedures include using various specialty tools to compress springs, extract components, and properly seat new parts. Technicians are advised to keep components clean and lubricate parts during installation.
Caterpillar cat 235 c excavator (prefix 5af) service repair manual (5af00001 ...uudfjjjskkemmd
1) The document provides instructions for removing and installing a fuel filter base and removing a fuel transfer pump from a Caterpillar 235C excavator.
2) The fuel filter base removal instructions include disconnecting fuel lines and removing bolts and the base. Installation is the reverse.
3) Removing the fuel transfer pump involves turning off fuel supply, disconnecting lines, and removing bolts to access the pump.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes:
1) Removing the flywheel using a lifting device and removing bolts, then removing the flywheel ring gear if necessary.
2) Installing the flywheel ring gear if it was removed by heating it and positioning it on the flywheel, then installing the flywheel using bolts and a lifting device.
3) Removing the crankshaft rear seal by removing housing bolts and pulling out the seal, gasket and housing.
4) Installing the new crankshaft rear seal using a installer tool and pressing the seal
The document provides instructions for removing and installing various components of a C13 engine, including:
- Electronic unit injectors and injector sleeves
- Turbocharger
- Solenoid valve (for exhaust balance)
- Air control valve
The instructions include lists of required tools and multi-step procedures for each component, with illustrations to identify parts. Safety notices are provided and proper torque specifications for fasteners.
The document provides instructions for removing and installing various components of a C13 engine, including:
- Electronic unit injectors and injector sleeves
- Turbocharger
- Solenoid valve (for exhaust balance)
- Air control valve
The instructions include lists of required tools and multi-step procedures describing how to disconnect hoses and other components, clean parts, apply lubricants, and torque fasteners when reinstalling components. Photographs and illustrations supplement the text instructions.
The document provides instructions for removing and installing various components of a C13 engine, including:
- Electronic unit injectors and injector sleeves
- Turbocharger
- Solenoid valve (for exhaust balance)
- Air control valve
The instructions include lists of required tools and multi-step procedures describing how to disconnect hoses and other components, clean parts, apply lubricants, and torque fasteners when reinstalling components. Photographs and illustrations supplement the text instructions.
Caterpillar cat d11 n track type tractor (prefix 4hk) service repair manual (...fjjskkefksme
The document provides instructions for disassembling the cylinder head of a D11N track-type tractor. The procedures include removing the inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
The document provides instructions for disassembling a cylinder head from a D11N track-type tractor. The procedures include removing inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
Caterpillar cat d11 n track type tractor (prefix 4hk) service repair manual (...fiskkdmdmdm
The document provides instructions for disassembling a cylinder head from a D11N track-type tractor. The procedures include removing inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
The document provides instructions for disassembling a cylinder head from a D11N track-type tractor. The procedures include removing inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
The document provides instructions for disassembling a cylinder head from a D11N track-type tractor. The procedures include removing inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
Caterpillar cat 321 d lcr excavator (prefix mpg) service repair manual (mpg00...fujsjfkkskefsme
1) The document provides instructions for removing and installing electronic unit injectors and turbochargers on a Caterpillar 321D LCR excavator.
2) Removing the electronic unit injector involves disconnecting harness assemblies, removing mounting bolts and nuts, and using tools to pull the injectors from the engine.
3) Turbocharger removal requires disconnecting tubes, hoses and nuts to detach the turbocharger from the engine.
Caterpillar cat 321 d lcr excavator (prefix mpg) service repair manual (mpg00...udfdesd
1. The document provides instructions for removing and installing electronic unit injectors, turbochargers, and exhaust manifolds on a Caterpillar 321D LCR excavator.
2. The electronic unit injector removal procedure involves disconnecting harness assemblies, removing mounting bolts and washers, and using a pry bar to remove the injectors.
3. Turbocharger removal requires disconnecting tubes, hoses and removing mounting nuts, while installation applies anti-seize compound to nuts and tightens clamps.
Caterpillar cat 321 d lcr excavator (prefix mpg) service repair manual (mpg00...fujsjfkskemm
1) The document provides instructions for removing and installing electronic unit injectors and turbochargers on a Caterpillar 321D LCR excavator.
2) Removing the electronic unit injector requires disconnecting harness assemblies and fuel lines, and using tools to remove mounting bolts and the injector.
3) Turbocharger removal requires disconnecting tubes, hoses and nuts to detach the turbocharger from the engine.
Caterpillar cat 321 d lcr excavator (prefix mpg) service repair manual (mpg00...jjskefkskemik
1. The document provides instructions for removing and installing an electronic unit injector, turbocharger, and exhaust manifold on a Caterpillar 321D LCR excavator.
2. The electronic unit injector removal procedure involves disconnecting harness assemblies and fuel lines before using a pry bar to remove the injector. Proper identification of parts is important.
3. Turbocharger removal requires disconnecting tubes, hoses and nuts before the turbocharger can be lifted off. Individual turbocharger components like the turbine housing and compressor housing can then be separated after further disassembly.
4. Exhaust manifold removal is dependent on first removing the turbocharger. Cleanliness is emphasized throughout the
1. The document provides instructions for removing and installing an electronic unit injector, turbocharger, and exhaust manifold on a Caterpillar 321D LCR excavator. It includes diagrams and lists required tools.
2. The procedure for removing an electronic unit injector involves disconnecting harness assemblies and fuel lines, removing mounting bolts and nuts, and using pry bars. Proper cleaning and identification of parts is emphasized.
3. Removing the turbocharger requires loosening clamps and removing mounting nuts and tubes connecting the turbocharger to other components.
4. Removal and installation of the exhaust manifold is briefly outlined, with safety notices about cleaning and containing fluids.
1) The document provides instructions for removing and installing an electronic unit injector from a C6.4 engine. Key steps include removing nuts and disconnecting harness assemblies, using tools to remove the injector, and installing new seals before reinstalling.
2) Instructions are also given for disassembling and assembling a turbocharger. Components like gaskets and clamps must be removed and indexed for reinstallation. Retaining rings are removed and installed using special pliers.
3) Safety notices emphasize the importance of cleanliness, containing fluids, and allowing fuel system pressure to purge before opening lines.
1) The document provides instructions for removing and installing an electronic unit injector from a C6.4 engine. Key steps include removing nuts and disconnecting harness assemblies, using tools to remove the injector, and installing new seals before reinstalling.
2) Instructions are also given for disassembling and assembling a turbocharger. Components like gaskets and clamps must be removed and indexed for reinstallation. Retaining rings are removed and installed using special pliers.
3) Safety notices emphasize the importance of cleanliness, containing fluids, and allowing fuel system pressure to purge before opening lines.
1. The document provides instructions for removing and installing various engine components, including electronic unit injectors, turbochargers, and exhaust manifolds, from a Caterpillar C6.4 engine.
2. The procedures describe removing components like nuts, bolts, clamps and hoses, and installing new gaskets and O-rings before reinstalling components with identification marks aligned.
3. Safety precautions are provided, such as waiting for fuel system pressure to be purged before opening lines and ensuring cleanliness to prevent contamination.
This document provides an outline and general precautions for a shop manual. It discusses the copyright of the manual, preparation for disassembling equipment, safety procedures, hydraulic and electrical equipment handling, welding repairs, and international unit systems. The outline covers topics to be included in the manual such as specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachment installation procedures.
Kobelco sk380 xdlc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides guidelines and safety precautions for maintenance and repairs of hydraulic excavators. It contains sections on specifications, maintenance procedures, systems overview, disassembly/assembly instructions, troubleshooting, engines, and optional attachment installation. The manual is intended to instruct repair and service technicians on proper procedures. Copyright of the manual belongs to Kobelco Construction Machinery and permission is required for copying or distributing its contents.
Kobelco sk300 lc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and engine information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installation of options. Safety information is provided throughout, including general safety, safety precautions, and warnings.
Kobelco sk270 srlc 5 (na 2018 yu08) hydraulic excavator service repair manualfjsjjekdkme
This document is the shop manual for a hydraulic excavator. It contains outlines, precautions, and general information for repairing and maintaining the excavator. The manual is divided into chapters covering specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachments. Precautions are provided for safety, preparing for disassembly, hydraulic and electrical equipment, and welding repairs. Copyright information is also included.
Kobelco sk260 lc 10 hydraulic excavator service repair manualfjsjjekdkme
This document outlines general precautions and guidelines for repairing excavator equipment according to the shop manual. It discusses preparing for disassembly, safety practices, hydraulic system repair, electrical work, and welding. Permission is required to copy or distribute content from the copyrighted manual. Measurements use the international unit system. Technicians should thoroughly read and understand the manual before performing any repair work.
Kobelco sk250 10 hydraulic excavator service repair manualfjsjjekdkme
This document outlines general precautions and guidelines for repairing excavator equipment according to the shop manual. It discusses preparing for disassembly, safety during disassembly and assembly, handling hydraulic and electrical equipment, welding repairs, and environmental issues. The outline notes that the copyright belongs to Kobelco and outlines rules for copying or distributing the manual's contents. It also introduces the international unit system used in specifications.
More Related Content
Similar to Caterpillar cat 352 f excavator (prefix rbf) service repair manual (rbf00001 and up)
The document provides instructions for removing and installing various components of a C13 engine, including:
- Electronic unit injectors and injector sleeves
- Turbocharger
- Solenoid valve (for exhaust balance)
- Air control valve
The instructions include lists of required tools and multi-step procedures for each component, with illustrations to identify parts. Safety notices are provided and proper torque specifications for fasteners.
The document provides instructions for removing and installing various components of a C13 engine, including:
- Electronic unit injectors and injector sleeves
- Turbocharger
- Solenoid valve (for exhaust balance)
- Air control valve
The instructions include lists of required tools and multi-step procedures describing how to disconnect hoses and other components, clean parts, apply lubricants, and torque fasteners when reinstalling components. Photographs and illustrations supplement the text instructions.
The document provides instructions for removing and installing various components of a C13 engine, including:
- Electronic unit injectors and injector sleeves
- Turbocharger
- Solenoid valve (for exhaust balance)
- Air control valve
The instructions include lists of required tools and multi-step procedures describing how to disconnect hoses and other components, clean parts, apply lubricants, and torque fasteners when reinstalling components. Photographs and illustrations supplement the text instructions.
Caterpillar cat d11 n track type tractor (prefix 4hk) service repair manual (...fjjskkefksme
The document provides instructions for disassembling the cylinder head of a D11N track-type tractor. The procedures include removing the inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
The document provides instructions for disassembling a cylinder head from a D11N track-type tractor. The procedures include removing inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
Caterpillar cat d11 n track type tractor (prefix 4hk) service repair manual (...fiskkdmdmdm
The document provides instructions for disassembling a cylinder head from a D11N track-type tractor. The procedures include removing inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
The document provides instructions for disassembling a cylinder head from a D11N track-type tractor. The procedures include removing inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
The document provides instructions for disassembling a cylinder head from a D11N track-type tractor. The procedures include removing inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
Caterpillar cat 321 d lcr excavator (prefix mpg) service repair manual (mpg00...fujsjfkkskefsme
1) The document provides instructions for removing and installing electronic unit injectors and turbochargers on a Caterpillar 321D LCR excavator.
2) Removing the electronic unit injector involves disconnecting harness assemblies, removing mounting bolts and nuts, and using tools to pull the injectors from the engine.
3) Turbocharger removal requires disconnecting tubes, hoses and nuts to detach the turbocharger from the engine.
Caterpillar cat 321 d lcr excavator (prefix mpg) service repair manual (mpg00...udfdesd
1. The document provides instructions for removing and installing electronic unit injectors, turbochargers, and exhaust manifolds on a Caterpillar 321D LCR excavator.
2. The electronic unit injector removal procedure involves disconnecting harness assemblies, removing mounting bolts and washers, and using a pry bar to remove the injectors.
3. Turbocharger removal requires disconnecting tubes, hoses and removing mounting nuts, while installation applies anti-seize compound to nuts and tightens clamps.
Caterpillar cat 321 d lcr excavator (prefix mpg) service repair manual (mpg00...fujsjfkskemm
1) The document provides instructions for removing and installing electronic unit injectors and turbochargers on a Caterpillar 321D LCR excavator.
2) Removing the electronic unit injector requires disconnecting harness assemblies and fuel lines, and using tools to remove mounting bolts and the injector.
3) Turbocharger removal requires disconnecting tubes, hoses and nuts to detach the turbocharger from the engine.
Caterpillar cat 321 d lcr excavator (prefix mpg) service repair manual (mpg00...jjskefkskemik
1. The document provides instructions for removing and installing an electronic unit injector, turbocharger, and exhaust manifold on a Caterpillar 321D LCR excavator.
2. The electronic unit injector removal procedure involves disconnecting harness assemblies and fuel lines before using a pry bar to remove the injector. Proper identification of parts is important.
3. Turbocharger removal requires disconnecting tubes, hoses and nuts before the turbocharger can be lifted off. Individual turbocharger components like the turbine housing and compressor housing can then be separated after further disassembly.
4. Exhaust manifold removal is dependent on first removing the turbocharger. Cleanliness is emphasized throughout the
1. The document provides instructions for removing and installing an electronic unit injector, turbocharger, and exhaust manifold on a Caterpillar 321D LCR excavator. It includes diagrams and lists required tools.
2. The procedure for removing an electronic unit injector involves disconnecting harness assemblies and fuel lines, removing mounting bolts and nuts, and using pry bars. Proper cleaning and identification of parts is emphasized.
3. Removing the turbocharger requires loosening clamps and removing mounting nuts and tubes connecting the turbocharger to other components.
4. Removal and installation of the exhaust manifold is briefly outlined, with safety notices about cleaning and containing fluids.
1) The document provides instructions for removing and installing an electronic unit injector from a C6.4 engine. Key steps include removing nuts and disconnecting harness assemblies, using tools to remove the injector, and installing new seals before reinstalling.
2) Instructions are also given for disassembling and assembling a turbocharger. Components like gaskets and clamps must be removed and indexed for reinstallation. Retaining rings are removed and installed using special pliers.
3) Safety notices emphasize the importance of cleanliness, containing fluids, and allowing fuel system pressure to purge before opening lines.
1) The document provides instructions for removing and installing an electronic unit injector from a C6.4 engine. Key steps include removing nuts and disconnecting harness assemblies, using tools to remove the injector, and installing new seals before reinstalling.
2) Instructions are also given for disassembling and assembling a turbocharger. Components like gaskets and clamps must be removed and indexed for reinstallation. Retaining rings are removed and installed using special pliers.
3) Safety notices emphasize the importance of cleanliness, containing fluids, and allowing fuel system pressure to purge before opening lines.
1. The document provides instructions for removing and installing various engine components, including electronic unit injectors, turbochargers, and exhaust manifolds, from a Caterpillar C6.4 engine.
2. The procedures describe removing components like nuts, bolts, clamps and hoses, and installing new gaskets and O-rings before reinstalling components with identification marks aligned.
3. Safety precautions are provided, such as waiting for fuel system pressure to be purged before opening lines and ensuring cleanliness to prevent contamination.
Similar to Caterpillar cat 352 f excavator (prefix rbf) service repair manual (rbf00001 and up) (16)
This document provides an outline and general precautions for a shop manual. It discusses the copyright of the manual, preparation for disassembling equipment, safety procedures, hydraulic and electrical equipment handling, welding repairs, and international unit systems. The outline covers topics to be included in the manual such as specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachment installation procedures.
Kobelco sk380 xdlc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides guidelines and safety precautions for maintenance and repairs of hydraulic excavators. It contains sections on specifications, maintenance procedures, systems overview, disassembly/assembly instructions, troubleshooting, engines, and optional attachment installation. The manual is intended to instruct repair and service technicians on proper procedures. Copyright of the manual belongs to Kobelco Construction Machinery and permission is required for copying or distributing its contents.
Kobelco sk300 lc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and engine information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installation of options. Safety information is provided throughout, including general safety, safety precautions, and warnings.
Kobelco sk270 srlc 5 (na 2018 yu08) hydraulic excavator service repair manualfjsjjekdkme
This document is the shop manual for a hydraulic excavator. It contains outlines, precautions, and general information for repairing and maintaining the excavator. The manual is divided into chapters covering specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachments. Precautions are provided for safety, preparing for disassembly, hydraulic and electrical equipment, and welding repairs. Copyright information is also included.
Kobelco sk260 lc 10 hydraulic excavator service repair manualfjsjjekdkme
This document outlines general precautions and guidelines for repairing excavator equipment according to the shop manual. It discusses preparing for disassembly, safety practices, hydraulic system repair, electrical work, and welding. Permission is required to copy or distribute content from the copyrighted manual. Measurements use the international unit system. Technicians should thoroughly read and understand the manual before performing any repair work.
Kobelco sk250 10 hydraulic excavator service repair manualfjsjjekdkme
This document outlines general precautions and guidelines for repairing excavator equipment according to the shop manual. It discusses preparing for disassembly, safety during disassembly and assembly, handling hydraulic and electrical equipment, welding repairs, and environmental issues. The outline notes that the copyright belongs to Kobelco and outlines rules for copying or distributing the manual's contents. It also introduces the international unit system used in specifications.
Kobelco sk60 8 hydraulic excavator service repair manualfjsjjekdkme
This document appears to be a shop manual that contains information for maintenance and repair of hydraulic excavators. It includes sections on specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachment installation procedures. The document provides safety precautions for repairs and disassembly/assembly. It also includes a table for international unit conversion. The manual is intended as a technical reference for maintenance technicians to perform repairs and find fault equipment.
This shop manual provides information needed for the disassembly, reassembly, and repair of a Kawasaki 135ZV-2 wheel loader. It includes specifications, tightening torques, and service standards for the chassis, power, hydraulic, brake, and operator station systems. Safety precautions and symbols are defined. The manual instructs technicians on removing and installing major components like the engine, transmission, axles, cylinders, and more. Cautions are provided regarding parts handling and use of sealants or lock agents.
This shop manual provides information for performing maintenance and repairs on Kawasaki wheel loaders. It contains safety warnings and symbols, an outline of the loader components and maintenance schedule, recommended lubricants, and sections about inspecting and adjusting the chassis and power groups. Technical details are given for linkage pins, center pins, engine and transmission mounts, and the radiator mount. The purpose is to ensure good machine performance through following the correct maintenance and repair procedures.
Kawasaki 92 z7 wheel loader service repair manualfjsjjekdkme
This document provides specifications for the 90Z7 and 92Z7 wheel loaders. The 90Z7 is powered by a Hino E13C-VV diesel engine and has operating weights ranging from 24550-24870 kg. The 92Z7 also uses a Hino E13C-VV diesel engine and has operating weights from 26840-27090 kg. Both models have 4 speeds in forward and reverse and an articulation angle of 37 degrees left and right. Dimensional specifications like overall length, width, height and other measurements are provided for each model/bucket type.
Kawasaki 92 z7 wheel loader operation and maintenance manualfjsjjekdkme
The document provides safety instructions and component information for operating heavy machinery. It outlines proper procedures for starting and using the machine, transporting loads, and performing maintenance safely. Operators must follow guidelines to prevent injuries or accidents from improper or unsafe operation. The manual describes the various controls, switches, and components in the operator cab.
Kawasaki 90 z7 wheel loader service repair manualfjsjjekdkme
This document provides specifications for the 90Z7 and 92Z7 wheel loaders. The 90Z7 is powered by a Hino E13C-VV diesel engine and has operating weights ranging from 24550-24870 kg. The 92Z7 also uses a Hino E13C-VV diesel engine and has operating weights from 26840-27090 kg. Both models have 4 speeds in forward and reverse and an articulation angle of 37 degrees left and right. Dimensional specifications like overall length, width, height and other measurements are provided for each model/bucket type.
Kawasaki 90 z7 wheel loader operation and maintenance manualfjsjjekdkme
The document provides safety instructions and component descriptions for a machine. It outlines various hazards to avoid when operating or servicing the machine, such as ensuring safety before leaving the operator's seat, wearing protective clothing, and avoiding contact with moving parts. It also describes the machine's components, including the operator's station, consoles, switches, and monitoring systems. Maintenance procedures should follow safety practices like supporting the machine properly and avoiding high-pressure fluids.
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 9001 and up)fjsjjekdkme
This document provides guidelines and precautions for disassembling and reassembling a wheel loader. It discusses preparing the work area, inspecting components, draining fluids, cleaning parts, applying lubricants, and ensuring proper tightening of fasteners. Special attention should be given to sliding surfaces, seals, and markings for reassembly. Tools and loose parts should be accounted for after completion. Floating seals and nylon slings require special handling to prevent damage or improper installation.
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 0101 and up)fjsjjekdkme
This document provides specifications and component layout information for a 90Z6 wheel loader.
The specifications section lists operating weights, engine details, dimensions, speeds and other technical specifications for the GSC and LSC models.
The component layout sections include diagrams and lists showing the layout and weights of major components such as the chassis, powertrain, hydraulic, electrical and other systems. Component names, locations and approximate weights are provided.
Kawasaki 90 z6 wheel loader parts catalogue manual (serial no. 90c7 9001 and up)fjsjjekdkme
This document is a parts catalog for a wheel loader model 90Z6 powered by a Cummins QSM11 engine. It lists parts grouped by system including the front axle, rear axle, power train, engine systems, cab, chassis, electrical systems, hydraulic system, brake system and loader attachments. The document provides part numbers, part names, quantities and the applicable serial number range for each part listed.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 5001 and up)fjsjjekdkme
This document provides specifications and layout diagrams for the components of a wheel loader. It includes:
- Specifications for dimensions, weights, engine details, speeds, and more.
- Overview diagrams showing the layout of main components such as the bucket, cylinders, lights, engine, and more.
- Detailed diagrams labeling locations of the engine, radiator, filters, tanks, valves, pumps, axles, and other parts.
- An overview of the electric system components around the cab, hydraulic oil tank, fuel tank, and engine.
- Sections providing specifications for the engine, hydraulic and electrical components.
The document contains detailed information on the specifications, component layout and electrical
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)fjsjjekdkme
The document contains sections from a shop manual for a wheel loader. It includes sections on general information, component layout, specifications, and maintenance procedures. The component layout sections describe and illustrate the main components of the wheel loader including the engine, hydraulic system, electrical system, cab, drive unit, and other key components. The specifications section lists technical specifications for the engine, operating weights, dimensions, travel speeds and other performance specifications.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR RBF
Configuration: 352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i06938734
Electronic Unit Injector - Remove and Install
SMCS - 1290-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5F-4764 Pry Bar 1
B
9U-6862 Tapered Brush 1
9U-7237 Brush Extension 1
C
9U-6863 Small Bore Brush 1
9U-7237 Brush Extension 1
D 8T-2998 Lubricant 1
E
1U-5718 Vacuum Pump 1
169-7372 Fluid Sampling Bottle -
4C-4057
Tube
7.9 mm (0.31 inch) OD
-
Start By:
a. Remove the rocker arms and shafts.
1. Turn the fuel supply to the “OFF” position.
1/5
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01855294
2. Disconnect hose assemblies (1).
3. Drain the fuel from the cylinder head.
Illustration 2 g01261606
4. Disconnect harness assembly (2) from electronic unit injector (3).
5. Remove bolt (4).
2/5
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01261609
6. Position Tooling (A) under clamp (5) to remove electronic unit injector (3).
Installation Procedure
NOTICE
When a fuel injector group is serviced, the new fuel injector group's
electronic injector code must be programmed into the engine's
personality module software by using the calibration menu on the
Electronic Service Tool. If the new fuel injector group's electronic code
is not entered, the previous fuel injector group's characteristics are
assumed.
If it is not possible to immediately reprogram the electronic injector
code of the injector into the personality module software, the engine
will not be severely harmed. The new electronic injector code should be
reprogrammed as quickly as possible in order to optimize engine
performance.
1. Install electronic unit injector (3) in the reverse order of removal.
a. Use Tooling (E) to remove the fuel and oil from the cylinder. Evacuate as much fuel
and oil as possible from the cylinder before installing the electronic unit injector.
Several evacuations may be necessary.
3/5
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g01009642
(7) Injector seating
(8) Tip bore
b. Use Tooling (B) to clean injector seating (7).
c. Use Tooling (C) to clean tip bore (8).
d. Lubricate the seals lightly with a 50/50 mix of clean engine oil and Tooling (D).
e. Tighten bolt (4) to a torque of 70 ± 15 N·m (52 ± 11 lb ft).
4/5
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 5 g03380304
Electronic unit injector serial number (Y)
f. Record all the injector serial numbers located on top of electronic unit injector (3).
The injector serial numbers will be used for downloading trim files for new or
exchanged electronic unit injectors (3). Refer to Troubleshooting, "Injector Trim
Calibration" for the correct procedure for injector trim calibration.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 09:03:07 UTC+0800 2020
5/5
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR RBF
Configuration: 352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i03531892
Electronic Unit Injector Sleeve - Remove and Install
SMCS - 1713-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6891 Injector Tool Group 1
B
9U-6862 Tapered Brush 1
9U-6863 Small Bore Brush 1
9U-7244 End Brush 1
9U-7237 Brush Extension 1
4C-5552 Large Bore Brush 1
C 4C-9507 Retaining Compound -
Start By:
a. Remove the electronic unit injectors.
1. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change"
for the correct draining and filling procedures.
1/4
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g01261663
2. Install Tooling (A) into electronic unit injector sleeve (1).
3. Tighten the nut until electronic unit injector sleeve (1) is pulled free of the cylinder head
assembly.
Illustration 2 g01860393
4. Remove electronic unit injector sleeve (1).
Installation Procedure
1. Use Tooling (B) to clean the bore in the cylinder head for the electronic unit injector sleeve.
NOTICE
Ensure that the electronic unit injector sleeve and the cylinder head
bore are completely free of oil, dirt, and sealant debris.
2/4
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g01261773
2. Install new O-ring seals (2) and (3) on electronic unit injector sleeve (1).
Note: Do not apply Tooling (C) to the cylinder head surfaces. Apply Tooling (C) on the
electronic unit injector sleeve only.
3. Apply a thin coat of Tooling (C) to O-ring seal (3) and the contact surface of electronic unit
injector sleeve (1) on the surface that is Marked "X".
Illustration 4 g01261802
4. Install Tooling (A) into the threads of electronic unit injector sleeve (1).
5. Position Tooling (A) and the electronic unit injector sleeve in the cylinder head. Use care
not to damage the O-ring seal on the electronic unit injector sleeve.
NOTICE
3/4
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Ensure that the electronic unit injector sleeve is properly seated in the
cylinder head. The Tooling will "RING" when the electronic unit
injector sleeve is fully seated in the bore of the cylinder head.
6. Use Tooling (A) and a hammer to install electronic unit injector sleeve (1) in the cylinder
head.
7. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change"
for the correct draining and filling procedures.
End By:
a. Install the electronic unit injectors.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 09:04:02 UTC+0800 2020
4/4
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR RBF
Configuration: 352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i05351523
Turbocharger - Remove and Install
SMCS - 1052-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description QTY
A 4C-5599 Anti-Seize Compound 1
Start By:
A. Remove the exhaust elbow.
1. Refer to Operation and Maintenance Manual, "Coolant - Change" for the proper draining
and filling procedures.
Illustration 1 g02170055
1/3
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 2. Disconnect clamp assembly (2) and remove diffuser (1) from the turbocharger.
3. Disconnect tube assemblies (3) and (4) .
Illustration 2 g01864534
4. Disconnect hose assemblies (5) and (7) .
5. Disconnect tube assembly (6) .
6. Attach a suitable lifting device to turbocharger (8). The weight of turbocharger (8) is
approximately 26 kg (57 lb).
7. Remove nuts (9) and turbocharger (8). Discard the gasket and nuts (9) .
Illustration 3 g02225358
8. If needed, carefully remove clamp assemblies (2) and (10). Discard the clamp assemblies.
Installation Procedure
1. Install turbocharger (8) in the reverse order of removal.
2/3
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. a. Put clean engine oil in the oil inlet of the turbocharger after assembly or before
installation. This action will provide lubrication during start-up and during storage.
b. Tighten new clamp assemblies (10) to a torque of 13.6 ± 1.2 N·m (120 ± 11 lb in).
c. Tighten new clamp assemblies (2) to a torque of 12 ± 4 N·m (106 ± 35 lb in).
d. Apply Tooling (A) to the threads of new nuts (9) prior to installation. Tighten nuts (9)
to a torque of 70 ± 5 N·m (52 ± 4 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 09:04:58 UTC+0800 2020
3/3
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR RBF
Configuration: 352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i04141424
Solenoid Valve (Exhaust Balance) - Remove and Install
SMCS - 1052-010-VL
Removal Procedure
Illustration 1 g02339283
Overhead view showing the location of the solenoid valve.
1. Disconnect hose assembly (1) and disconnect tube assembly (5) .
2. Disconnect harness assembly (3) .
3. Remove bolt (2) and remove solenoid valve (4) .
Installation Procedure
1. Install the solenoid valve (4) in the reverse order.
1/2
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 09:05:54 UTC+0800 2020
2/2
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR RBF
Configuration: 352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i05337709
Air Control Valve - Remove and Install
SMCS - 108A-010
Removal Procedure
Illustration 1 g02824399
1. Disconnect harness assemblies (1).
2. Disconnect the harness assembly from pressure sensor (3). Remove pressure sensor (3).
3. Remove hoses (2) and (4).
1/2
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g02824456
4. Remove bolts (5) and remove air control valve assembly (6).
Illustration 3 g02824481
5. Remove bolts (8). Remove outlet elbow (9) and inlet elbow (10) from air control valve (7).
Remove and discard the seals.
6. Remove and discard the seals from air control valve (7).
Installation Procedure
1. Install air control valve (7) in the reverse order of removal.
a. Tighten pressure sensor (3) to a torque of 10 ± 2 N·m (89 ± 18 lb in).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 09:06:50 UTC+0800 2020
2/2
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR RBF
Configuration: 352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i05351525
Exhaust Gas Valve (NRS) - Remove and Install
SMCS - 108N-010; 5510
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 207-1600 (1)
Rubber Lubricant 1
( 1 )
For Use In EAME
Illustration 1 g02848005
1. Disconnect harness assemblies (1) and disconnect tube assemblies (2) .
2. Loosen clamp (4) and remove tube assembly (3). Discard clamp (4) and the O-ring seals.
1/2
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g02848045
3. Loosen clamps (6) and remove hose (7) .
4. Remove bolts (9), clip (8), and exhaust control valve (5) .
Installation Procedure
1. Install exhaust control valve (5) in the reverse order of removal.
a. Apply Tooling (A) to the O-ring seals and the venturi-side bore of tube assembly (3) .
b. Tighten clamps (4) to a torque of 8.5 ± 2 N·m (75 ± 18 lb in).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 09:07:45 UTC+0800 2020
2/2
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR RBF
Configuration: 352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i03546401
Exhaust Gas Valve (NRS) - Disassemble
SMCS - 108N-015; 5510
Disassembly Procedure
Start By:
a. Remove the exhaust gas valve.
Illustration 1 g02173623
1. Remove temperature sensor (1).
2. Remove bolts (2). Separate actuator assembly (3) from valve housing (4).
1/2
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 2 g01845473
3. Remove nut (8), washer (7), and solenoid (6).
4. Remove spool (5).
Illustration 3 g02173629
5. Remove O-rings (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 09:08:41 UTC+0800 2020
2/2
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR RBF
Configuration: 352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i03546406
Exhaust Gas Valve (NRS) - Assemble
SMCS - 108N-016; 5510
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-3931 Anti-Seize Compound −
B 1P-0808 Multipurpose Grease −
Illustration 1 g02173629
Note: Lubricate all of the O-ring seals with the lubricant that is being sealed.
1. Install O-ring seals (9).
1/3
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 2 g01845473
2. Install spool (5). Tighten spool (5) to a torque of 50 ± 5 N·m (37 ± 4 lb ft).
3. Install solenoid (6), washer (7), and nut (8). Tighten nut (8) to a torque of 20 ± 2.5 N·m
(177 ± 22 lb in) .
Illustration 3 g01871983
4. Fill Cavity (B) with Tooling (B). Cavity (B) is found on the valve housing.
Illustration 4 g02173623
5. Install actuator assembly (3) on valve housing (4).
2/3
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 6. Apply Tooling (A) to the threads on temperature sensor (1). Tighten temperature sensor (1)
to a torque of 45 ± 5 N·m (33 ± 4 lb ft).
End By:
a. Install the exhaust control valve.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 09:09:37 UTC+0800 2020
3/3
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine(M0081344 ...
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...