This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...zatao0179249295
This document provides instructions for removing and installing various engine components on a 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing gears, seals, bolts and bearings.
2. Removing the flywheel by detaching lifting brackets, installing guide studs, and removing bolts and the flywheel.
3. Installing the flywheel by heating the ring gear, attaching lifting brackets, applying threadlocker to bolts, and tightening bolts to specification.
4. Removing the crankshaft rear seal by removing bolts and the seal, and inspecting the crankshaft surface.
5. Installing
The document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1) Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2) Removing the flywheel by attaching lifting tools and removing bolts.
3) Removing the crankshaft rear seal by removing bolts.
Installation procedures are also provided with details on cleaning, heating, cooling, and applying threadlocker to parts before tightening to specified torques. Tools required are listed for each procedure.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...yinranhe0814
The document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1) Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2) Removing the flywheel by attaching lifting tools and removing bolts.
3) Removing the crankshaft rear seal by removing bolts.
Installation procedures are also provided with details on cleaning, heating, cooling, and applying threadlocker to parts before tightening bolts to the specified torque. Tools required are listed for each procedure.
This document provides instructions for removing and installing various components of a C13 engine, including:
1. Removing and installing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Installing the flywheel by heating the ring gear, attaching lifting tools, applying loctite, and tightening bolts.
4. Removing the crankshaft rear seal by removing bolts.
5. Installing the crankshaft rear seal by cleaning, applying primer and retaining compound, and installing the seal.
This document provides instructions for removing and installing various engine components on a 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing gears, seals, bolts and bearings.
2. Removing the flywheel by detaching lifting brackets, installing guide studs, and removing bolts and the flywheel.
3. Installing the flywheel by heating the ring gear, attaching lifting brackets, applying threadlocker to bolts, and tightening bolts to specification.
4. Removing the crankshaft rear seal by removing bolts and the seal, and inspecting the crankshaft surface.
5. Installing
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...wfu089267
This document provides instructions for removing and installing various components of a C13 engine, including:
1. Removing and installing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Installing the flywheel by heating the ring gear, attaching lifting tools, applying loctite to bolts, and tightening bolts.
4. Removing the crankshaft rear seal by removing bolts and the seal.
5. Installing the crankshaft rear seal by cleaning parts, applying primer and retaining compound, and installing the seal with bol
Caterpillar cat 349 d l excavator (prefix fla) service repair manual (fla0000...fjskekxcddmmme
1. The document provides installation and removal instructions for various components of a C13 engine, including the flywheel, rear gear group, crankshaft rear seal, and more.
2. Detailed steps and illustrations are given for each procedure, including the necessary tools. Precautions are outlined, such as containing fluids and keeping parts clean.
3. Specifications and additional reference documents are cited to ensure proper installation and inspection of components like the crankshaft seal surface and wear sleeves.
Caterpillar cat 349 d l excavator (prefix fla) service repair manual (fla0000...hhfjksekmm
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1) Removing the rear gear group by removing several bolts, gears, seals, and bearings.
2) Removing the flywheel using lifting equipment and special tools after removing mounting bolts.
3) Installing the flywheel by heating components, applying threadlocker to bolts, and torquing bolts to specification.
4) Removing the crankshaft rear seal by removing mounting bolts.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...zatao0179249295
This document provides instructions for removing and installing various engine components on a 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing gears, seals, bolts and bearings.
2. Removing the flywheel by detaching lifting brackets, installing guide studs, and removing bolts and the flywheel.
3. Installing the flywheel by heating the ring gear, attaching lifting brackets, applying threadlocker to bolts, and tightening bolts to specification.
4. Removing the crankshaft rear seal by removing bolts and the seal, and inspecting the crankshaft surface.
5. Installing
The document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1) Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2) Removing the flywheel by attaching lifting tools and removing bolts.
3) Removing the crankshaft rear seal by removing bolts.
Installation procedures are also provided with details on cleaning, heating, cooling, and applying threadlocker to parts before tightening to specified torques. Tools required are listed for each procedure.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...yinranhe0814
The document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1) Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2) Removing the flywheel by attaching lifting tools and removing bolts.
3) Removing the crankshaft rear seal by removing bolts.
Installation procedures are also provided with details on cleaning, heating, cooling, and applying threadlocker to parts before tightening bolts to the specified torque. Tools required are listed for each procedure.
This document provides instructions for removing and installing various components of a C13 engine, including:
1. Removing and installing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Installing the flywheel by heating the ring gear, attaching lifting tools, applying loctite, and tightening bolts.
4. Removing the crankshaft rear seal by removing bolts.
5. Installing the crankshaft rear seal by cleaning, applying primer and retaining compound, and installing the seal.
This document provides instructions for removing and installing various engine components on a 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing gears, seals, bolts and bearings.
2. Removing the flywheel by detaching lifting brackets, installing guide studs, and removing bolts and the flywheel.
3. Installing the flywheel by heating the ring gear, attaching lifting brackets, applying threadlocker to bolts, and tightening bolts to specification.
4. Removing the crankshaft rear seal by removing bolts and the seal, and inspecting the crankshaft surface.
5. Installing
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...wfu089267
This document provides instructions for removing and installing various components of a C13 engine, including:
1. Removing and installing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Installing the flywheel by heating the ring gear, attaching lifting tools, applying loctite to bolts, and tightening bolts.
4. Removing the crankshaft rear seal by removing bolts and the seal.
5. Installing the crankshaft rear seal by cleaning parts, applying primer and retaining compound, and installing the seal with bol
Caterpillar cat 349 d l excavator (prefix fla) service repair manual (fla0000...fjskekxcddmmme
1. The document provides installation and removal instructions for various components of a C13 engine, including the flywheel, rear gear group, crankshaft rear seal, and more.
2. Detailed steps and illustrations are given for each procedure, including the necessary tools. Precautions are outlined, such as containing fluids and keeping parts clean.
3. Specifications and additional reference documents are cited to ensure proper installation and inspection of components like the crankshaft seal surface and wear sleeves.
Caterpillar cat 349 d l excavator (prefix fla) service repair manual (fla0000...hhfjksekmm
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1) Removing the rear gear group by removing several bolts, gears, seals, and bearings.
2) Removing the flywheel using lifting equipment and special tools after removing mounting bolts.
3) Installing the flywheel by heating components, applying threadlocker to bolts, and torquing bolts to specification.
4) Removing the crankshaft rear seal by removing mounting bolts.
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include draining oil, removing covers and shafts, using lifting tools to remove heavy components, and reinstalling parts in reverse order while applying new seals and grease. Detailed diagrams show tooling and component locations to aid the process.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar 3046 engine. The removal procedure involves removing the front housing, idler gear bolt, thrust plate, idler gear, idler shaft, and front plate. The installation procedure instructs to install the front plate and idler shaft, align the timing marks, and install the idler gear, thrust plate, and idler gear bolt. References are provided for removing and installing the other gears in the front gear group.
The document provides removal and installation instructions for a variable valve actuator oil pressure sensor, variable valve actuator oil pressure solenoid, water pump, water pump disassembly and assembly, water temperature regulator housing, and precooler from a C18 industrial engine. The instructions include lists of required tools and step-by-step procedures with illustrations to guide removal and installation of the components. Safety notices are provided to contain fluids, keep parts clean, and dispose of fluids properly.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting parts before installation and applying thread locking compound to bolts.
2. Installing the front plate, gears, and shafts in the correct order and orientation while adjusting backlash.
3. Torque specifications for installing bolts and nuts.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page document that includes:
1) A list of required tools and safety notices for the removal procedure. The procedure involves removing bolts, lifting devices, and a gasket from the flywheel housing.
2) A list of required tools and safety notices for the installation procedure. The procedure involves cleaning, applying sealant, positioning a gasket and flywheel housing, and tightening bolts in a specific sequence and torque.
3) The document concludes by stating additional installation steps to complete the job.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Removing and installing the fuel priming pump.
- Removing the fuel filter base and disassembling/assembling its components.
- Removing and installing the fuel transfer pump.
- Removing the electronic unit injectors.
The summaries provide concise overviews of the removal and installation procedures for each component in 3 sentences or less.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C18 Industrial Engine, including:
1) Removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) Disassembling and assembling the fuel filter base to replace seals and fittings.
3) Procedures include disconnecting fuel lines and electrical connections, marking parts for reinstallation, and applying thread lock compounds. Safety notices advise containing fluids and preventing contamination.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base on the engine and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
The document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger on a C9.3 Industrial Engine. Key steps include draining fluids, removing connecting components, cleaning parts, applying sealants, and torquing fasteners to the specified values. Required tools include pry bars, brushes, vacuum equipment, and wrenches. Cautions are provided regarding containing fluids and preventing contamination.
1. The document provides instructions for removing and installing the crankshaft front seal on a C18 industrial engine.
2. The removal procedure involves using various tools like a slide hammer puller and pry bar to remove the existing seal and wear sleeve.
3. The installation procedure lists the required tools and instructs to use a seal locator, installer, and bolts to properly position and set the new seal and wear sleeve.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C11 engine, including:
1. Removing the rear gear group which involves removing multiple gears, seals, bolts and covers.
2. Removing the flywheel which requires attaching lifting equipment and removing bolts.
3. Installing the rear gear group and flywheel which provides detailed steps and specifications for installing components like bearings and seals.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine, including:
1. Valves, springs, retainers, and rotators. Tools are needed to compress springs during removal and installation.
2. Valve guides. Guides are removed and installed using driver tools to the proper height above the cylinder head.
3. Valve seat inserts. Seat inserts are removed and installed using specialized driver tools for the inlet and exhaust valves.
4. The engine oil filter base and filter. Hoses are disconnected and bolts removed to take off the base and gasket. A strap wrench is recommended to remove the oil filter.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document contains illustrations and lists required tools for each procedure.
This document provides instructions for disassembling and assembling the freewheel stator component of a torque converter. The disassembly process involves using various tools to remove over 30 individual parts in a specific sequence. Cleanliness is emphasized. The assembly process reverses the disassembly steps and provides additional details like proper orientation and torque specifications for reinstalling components.
This document provides instructions for disassembling and assembling the torque converter of a 966H wheel loader. It begins with required tools and safety notices. The disassembly instructions describe removing over 30 individual parts in multiple steps, including the torque converter housing, impeller, stator, carrier shaft, and turbine. The assembly section then lists the components and provides the reverse order for reassembling the torque converter. Cleanliness is emphasized as important during disassembly and assembly.
This document provides instructions for removing and installing various components of the rear differential and carrier assembly of a Caterpillar 966C wheel loader, including removing the rear axles, disconnecting air lines, removing mounting bolts and lifting the rear of the machine to access the differential and carrier. The rear differential and carrier unit weighs 350 pounds and houses the internal gearing that allows the rear wheels to turn at different speeds while receiving equal torque.
This document provides instructions for disassembling and assembling the piston pump of a 962K wheel loader steering system. The disassembly procedure has 28 steps that remove components like valves, spools, springs, and bearings. The assembly procedure reverses this with 31 steps, ensuring O-rings and springs are correctly installed to prevent injury. Precautions are provided to safely release spring forces during disassembly and assembly.
The document provides instructions for removing and installing a secondary steering pump and electric motor on a Caterpillar 962K wheel loader. It outlines 28 steps for disassembly of the pump which include removing valves, spools, plugs, springs and other components. The assembly section lists 34 steps for reinstalling the parts in reverse order and adjusting axial shaft end play clearance.
This document provides instructions for removing and installing various engine components on a Caterpillar 950B wheel loader, including the spacer plate, water directors, lifter group, camshaft, and camshaft bearings. The procedures describe removing each part, checking part dimensions, cleaning surfaces, lubricating, and correctly installing each part while maintaining proper engine timing. Tools required are also listed.
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include draining oil, removing covers and shafts, using lifting tools to remove heavy components, and reinstalling parts in reverse order while applying new seals and grease. Detailed diagrams show tooling and component locations to aid the process.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar 3046 engine. The removal procedure involves removing the front housing, idler gear bolt, thrust plate, idler gear, idler shaft, and front plate. The installation procedure instructs to install the front plate and idler shaft, align the timing marks, and install the idler gear, thrust plate, and idler gear bolt. References are provided for removing and installing the other gears in the front gear group.
The document provides removal and installation instructions for a variable valve actuator oil pressure sensor, variable valve actuator oil pressure solenoid, water pump, water pump disassembly and assembly, water temperature regulator housing, and precooler from a C18 industrial engine. The instructions include lists of required tools and step-by-step procedures with illustrations to guide removal and installation of the components. Safety notices are provided to contain fluids, keep parts clean, and dispose of fluids properly.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting parts before installation and applying thread locking compound to bolts.
2. Installing the front plate, gears, and shafts in the correct order and orientation while adjusting backlash.
3. Torque specifications for installing bolts and nuts.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page document that includes:
1) A list of required tools and safety notices for the removal procedure. The procedure involves removing bolts, lifting devices, and a gasket from the flywheel housing.
2) A list of required tools and safety notices for the installation procedure. The procedure involves cleaning, applying sealant, positioning a gasket and flywheel housing, and tightening bolts in a specific sequence and torque.
3) The document concludes by stating additional installation steps to complete the job.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Removing and installing the fuel priming pump.
- Removing the fuel filter base and disassembling/assembling its components.
- Removing and installing the fuel transfer pump.
- Removing the electronic unit injectors.
The summaries provide concise overviews of the removal and installation procedures for each component in 3 sentences or less.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C18 Industrial Engine, including:
1) Removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) Disassembling and assembling the fuel filter base to replace seals and fittings.
3) Procedures include disconnecting fuel lines and electrical connections, marking parts for reinstallation, and applying thread lock compounds. Safety notices advise containing fluids and preventing contamination.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base on the engine and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
The document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger on a C9.3 Industrial Engine. Key steps include draining fluids, removing connecting components, cleaning parts, applying sealants, and torquing fasteners to the specified values. Required tools include pry bars, brushes, vacuum equipment, and wrenches. Cautions are provided regarding containing fluids and preventing contamination.
1. The document provides instructions for removing and installing the crankshaft front seal on a C18 industrial engine.
2. The removal procedure involves using various tools like a slide hammer puller and pry bar to remove the existing seal and wear sleeve.
3. The installation procedure lists the required tools and instructs to use a seal locator, installer, and bolts to properly position and set the new seal and wear sleeve.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C11 engine, including:
1. Removing the rear gear group which involves removing multiple gears, seals, bolts and covers.
2. Removing the flywheel which requires attaching lifting equipment and removing bolts.
3. Installing the rear gear group and flywheel which provides detailed steps and specifications for installing components like bearings and seals.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine, including:
1. Valves, springs, retainers, and rotators. Tools are needed to compress springs during removal and installation.
2. Valve guides. Guides are removed and installed using driver tools to the proper height above the cylinder head.
3. Valve seat inserts. Seat inserts are removed and installed using specialized driver tools for the inlet and exhaust valves.
4. The engine oil filter base and filter. Hoses are disconnected and bolts removed to take off the base and gasket. A strap wrench is recommended to remove the oil filter.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document contains illustrations and lists required tools for each procedure.
This document provides instructions for disassembling and assembling the freewheel stator component of a torque converter. The disassembly process involves using various tools to remove over 30 individual parts in a specific sequence. Cleanliness is emphasized. The assembly process reverses the disassembly steps and provides additional details like proper orientation and torque specifications for reinstalling components.
This document provides instructions for disassembling and assembling the torque converter of a 966H wheel loader. It begins with required tools and safety notices. The disassembly instructions describe removing over 30 individual parts in multiple steps, including the torque converter housing, impeller, stator, carrier shaft, and turbine. The assembly section then lists the components and provides the reverse order for reassembling the torque converter. Cleanliness is emphasized as important during disassembly and assembly.
This document provides instructions for removing and installing various components of the rear differential and carrier assembly of a Caterpillar 966C wheel loader, including removing the rear axles, disconnecting air lines, removing mounting bolts and lifting the rear of the machine to access the differential and carrier. The rear differential and carrier unit weighs 350 pounds and houses the internal gearing that allows the rear wheels to turn at different speeds while receiving equal torque.
This document provides instructions for disassembling and assembling the piston pump of a 962K wheel loader steering system. The disassembly procedure has 28 steps that remove components like valves, spools, springs, and bearings. The assembly procedure reverses this with 31 steps, ensuring O-rings and springs are correctly installed to prevent injury. Precautions are provided to safely release spring forces during disassembly and assembly.
The document provides instructions for removing and installing a secondary steering pump and electric motor on a Caterpillar 962K wheel loader. It outlines 28 steps for disassembly of the pump which include removing valves, spools, plugs, springs and other components. The assembly section lists 34 steps for reinstalling the parts in reverse order and adjusting axial shaft end play clearance.
This document provides instructions for removing and installing various engine components on a Caterpillar 950B wheel loader, including the spacer plate, water directors, lifter group, camshaft, and camshaft bearings. The procedures describe removing each part, checking part dimensions, cleaning surfaces, lubricating, and correctly installing each part while maintaining proper engine timing. Tools required are also listed.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 EXCAVATOR WEC
Configuration: 349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06931709
Gear Group (Rear) - Remove and Install
SMCS - 1206-010; 1212-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp. 1
B 1P-0510 Driver Gp 1
Start By:
a. Remove the electric starting motor.
b. Remove the flywheel.
1. Support the engine.
1/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g06002548
2. Remove bolts (2) and rear crankshaft seal (1).
Illustration 2 g06002556
3. Remove bolts (4) and the washers. Remove cover (3) and the seal.
Illustration 3 g06002558
4. Remove gear (7), bolts (6), and gear (5).
Illustration 4 g06002564
2/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. 5. Remove O-ring seal (8) from gear (7).
Illustration 5 g06172622
6. Use Tooling (A) to remove bushing (7A) from gear assembly (7).
Illustration 6 g06172537
7. Remove bolts (9), adapter assembly (10), and the O-ring seal.
Illustration 7 g06172541
8. Use Tooling (B) to remove bearing (11) from adapter assembly (10).
3/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 8 g06172549
9. Remove gear assembly (12).
Illustration 9 g06172554
10. Remove cover (13) and the O-ring seal.
Illustration 10 g06172557
11. Use Tooling (B) to remove bearing (14).
Installation Procedure
4/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Table 2
Required Tools
Tool Part Number Part Description Qty
A 095-0706 Bolt 2
Illustration 11 g06172557
Illustration 12 g06172580
5/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 13 g06172587
1. Lower the temperature of bearing (14). Be sure to match Dimension (B) and Dimension (C)
when installing bearing (14.). Dimension (B) indicates the angle of the joint on bearing (14).
Dimension (B) is 15° ± 1°. Dimension (C) shows the distance from bearing (14) to the end
of the bore. Dimension (C) is 4.000 ± 0.500 mm (0.1575 ± 0.0197 inch).
Illustration 14 g06172554
2. Install the O-ring seal and cover (9).
6/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 15 g06172597
3. Install gear assembly (12) with oil passage plug (12A) facing out.
Illustration 16 g06172601
Illustration 17 g06172609
4. Lower the temperature of bearing (11). Be sure to match Dimension (F) and Dimension (G)
when installing bearing (11) into adapter assembly (10). Dimension (F) indicates the angle
of the joint on bearing (11). Dimension (F) is 15° ± 1°. Dimension (G) shows the distance
from bearing (11) to the end of the bore. Dimension (G) is 3.500 ± 0.500 mm
(0.1378 ± 0.0197 inch).
7/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 18 g06172537
5. Install the O-ring seal, adapter assembly (10), and bolts (9).
Illustration 19 g06172619
6. Lower the temperature of bearing (7A). Install bearing (7A) into gear assembly (7). Be sure
that each relief (H) is within 2° of each relief in gear assembly (7).
Illustration 20 g06002564
7. Install O-ring seal (8) onto gear (7).
8/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 21 g06002578
8. Install gear (5) and bolts (6).
Note: Tooling (A) is for supporting gear (7) during the installation of the cover and the rear
crankshaft seal.
Note: The bolt holes in gear (7) are not symmetrical. When installing Tooling (C), check
the rest of the bolts holes in gear (7) are aligned with the holes in the crankshaft.
9. Install gear (7) and Tooling (C).
Illustration 22 g06002581
10. Install cover (3), the seal, bolts (4), and the washers.
9/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 23 g06002592
11. Install rear crankshaft seal (1) and bolts (2).
12. Remove Tooling (C).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 7 12:26:41 UTC+0800 2020
10/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M0...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 EXCAVATOR WEC
Configuration: 349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249234
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B FT2712 Guide Stud 1
1/2
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 1 g01132214
1. Attach Tooling (A) and a suitable lifting device to flywheel (2). The weight of flywheel (2)
is approximately 79 kg (175 lb).
2. Remove top bolt (1). Install Tooling (B).
3. Remove remaining bolts (1).
4. Remove flywheel (2).
5. Use a hammer and a punch in order to remove the ring gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 7 12:27:37 UTC+0800 2020
2/2
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 EXCAVATOR WEC
Configuration: 349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06123534
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B FT2712 Guide Stud 1
C - Loctite 242 1
Always wear protective gloves when handling parts that have been
heated.
1. Raise the temperature of the ring gear. Position the ring gear with the part number toward
the crankshaft. Install the ring gear on the flywheel. Allow the ring gear to cool. Use a soft
hammer in order to seat the ring gear against the shoulder of the flywheel.
1/2
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 1 g01132214
2. Attach Tooling (A) and a suitable lifting device to flywheel (2) . The weight of flywheel (2)
is approximately 79 kg (175 lb).
3. Position flywheel (2) on Tooling (B) .
4. Apply Tooling (C) to bolts (1) .
5. Install bolts (1) . Remove Tooling (B) . Install remaining bolt (1) . Tighten the bolts evenly
to a torque of 300 ± 40 N·m (221 ± 30 lb ft).
6. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect" for the
correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 7 12:28:33 UTC+0800 2020
2/2
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 EXCAVATOR WEC
Configuration: 349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06010889
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 1 g01132235
1. Remove bolts (1).
2. Remove crankshaft rear seal (2).
Note: Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual Inspection and
Magnetic Particle Inspection" for the correct inspection procedure of the crankshaft seal surface.
Note: Refer to Reuse and Salvage Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9,
C-9, C10, C11, C12, C-12, C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the
correct specifications of the crankshaft.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 7 12:29:29 UTC+0800 2020
2/2
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 EXCAVATOR WEC
Configuration: 349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06010890
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 Primer N -
B - Loctite 620 Retaining Compound -
C 147-2675 Wear Sleeve Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 1 g01140085
Illustration 2 g03698745
Numerical tightening sequence for bolts (2).
Note: If required, install a crankshaft wear sleeve at engine overhaul. For more information
please refer to the following Reuse and Salvage Guidelines. Refer to Reuse and Salvage
Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9, C-9, C10, C11, C12, C-12,
2/3
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the correct specifications
of the crankshaft. Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual
Inspection and Magnetic Particle Inspection" for the correct inspection procedure of the
crankshaft seal surface.
1. If a crankshaft wear sleeve is necessary, refer to Step 1.a through Step 1.d to install the
crankshaft wear sleeve. If a crankshaft wear sleeve is not necessary, refer to Step 2.
a. Clean and polish the crankshaft of imperfections.
b. Use Tooling (A) to clean the outside diameter of the crankshaft and the inside
diameter of the crankshaft wear sleeve.
c. Apply Tooling (B) to the outside diameter of the crankshaft and the inside diameter of
the crankshaft wear sleeve.
d. Use Tooling (C) to install the crankshaft wear sleeve.
Note: Leave the shipping sleeve in place to install the crankshaft rear seal. The crankshaft
rear seal must be installed dry.
Note: If the seal group, O-ring seal, and the shipping sleeve are separated, these
components should not be used.
2. Lubricate the O-ring seal with clean engine oil that is on the back of the crankshaft rear seal
(1).
3. Position crankshaft rear seal (1) and the shipping sleeve over the crankshaft. Push
crankshaft rear seal (1) in place to dislodge the shipping sleeve.
Note: Do not remove the shipping sleeve until bolts (2) are installed.
4. Install new bolts (2) hand tight. Then, tighten bolts (2) in numerical sequence, shown in
Illustration 2. Tighten bolts (2) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 7 12:30:24 UTC+0800 2020
3/3
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 EXCAVATOR WEC
Configuration: 349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249340
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
1. Support the engine.
Illustration 1 g01132273
1/3
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. 2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2)
is approximately 62 kg (137 lb).
3. Remove bolts (1) and flywheel housing (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8846 Gasket Sealant 1
1. Apply Tooling (A) to the face of the cylinder block.
Illustration 2 g01132273
2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2)
is approximately 62 kg (137 lb). Position flywheel housing (2) on the rear of the cylinder
block.
3. Install bolts (1).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Mon Sep 7 12:31:20 UTC+0800 2020
2/3
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 EXCAVATOR WEC
Configuration: 349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249982
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
1/3
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 1 g01132580
1. Remove belt (1).
2. Attach a suitable lifting device to crankshaft vibration damper and pulley (3). The weight of
crankshaft vibration damper and pulley (3) is approximately 27 kg (60 lb). Remove bolts
(2).
3. Remove crankshaft vibration damper and pulley (3).
Installation Procedure
2/3
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...