This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. The removal procedure involves removing bolts and seals to access the rear gear components. Tools are required to remove bearings from assemblies. The installation procedure specifies cleaning parts and applying threadlock. Dimensions must be matched and temperatures lowered when pressing components in place. Torques and tightening sequences are provided.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...zatao0179249295
This document provides instructions for removing and installing rear gear group components on a Caterpillar 345C excavator engine. It includes:
1. Detailed steps for removing the rear crankshaft seal, gears, covers, and bearings.
2. Requirements for specific tools to aid in removal and installation.
3. Procedures for installing replacement components, including ensuring proper bearing fits and alignments.
4. Cautions for handling heated parts and containing fluids.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...yinranhe0814
This document provides instructions for removing and installing rear gear group components on a Caterpillar 345C excavator engine. It includes:
1. Detailed steps for removing the rear crankshaft seal, gears, covers, and bearings.
2. Requirements for specific tools to aid in removal and installation.
3. Procedures for installing replacement components, including ensuring proper bearing fits and alignments.
4. Cautions for handling heated parts and containing fluids.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...wfu089267
This document provides instructions for removing and installing the rear gear group on a Caterpillar 345C excavator engine. It outlines the required tools and parts, provides illustrations of each step, and describes the procedures for disassembly and assembly. The disassembly process involves removing 14 separate components including gears, covers, seals, and bearings. The installation process describes properly positioning 11 components and applying sealant or lubricant as needed. Special attention is placed on properly seating bearings at the correct angles and distances from ends of bores.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...fjisejkdmd8id
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f8sejdkdmdijd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific instructions for installing seals and bearings. Tools and torque specifications are provided.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...yqen95561858
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...zatao0179249295
This document provides instructions for removing and installing rear gear group components on a Caterpillar 345C excavator engine. It includes:
1. Detailed steps for removing the rear crankshaft seal, gears, covers, and bearings.
2. Requirements for specific tools to aid in removal and installation.
3. Procedures for installing replacement components, including ensuring proper bearing fits and alignments.
4. Cautions for handling heated parts and containing fluids.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...yinranhe0814
This document provides instructions for removing and installing rear gear group components on a Caterpillar 345C excavator engine. It includes:
1. Detailed steps for removing the rear crankshaft seal, gears, covers, and bearings.
2. Requirements for specific tools to aid in removal and installation.
3. Procedures for installing replacement components, including ensuring proper bearing fits and alignments.
4. Cautions for handling heated parts and containing fluids.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...wfu089267
This document provides instructions for removing and installing the rear gear group on a Caterpillar 345C excavator engine. It outlines the required tools and parts, provides illustrations of each step, and describes the procedures for disassembly and assembly. The disassembly process involves removing 14 separate components including gears, covers, seals, and bearings. The installation process describes properly positioning 11 components and applying sealant or lubricant as needed. Special attention is placed on properly seating bearings at the correct angles and distances from ends of bores.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...fjisejkdmd8id
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f8sejdkdmdijd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific instructions for installing seals and bearings. Tools and torque specifications are provided.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...yqen95561858
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...ze3xiandiao
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f7usuejkdkddm3
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...ufs89eodkdmdm
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkskmmdmd1
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkksmemmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other gears and covers. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...ifkkdkmdmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...jjfksekdmejik
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves removing multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel, which involves cleaning, applying sealant, heating components, and torquing bolts to the specified values. Precise alignment and positioning of gears and bearings is critical.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...fjjskqazxedmmem
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures to remove the rear crankshaft seal, gear group components like gears and covers, and installing new seals and bearings in their proper positions.
2. Detailed steps and illustrations are provided to remove and install the flywheel.
3. Removal of the crankshaft rear seal is outlined, noting inspection of the crankshaft seal surface afterwards. Precautions are included to contain fluids during disassembly.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...jjfksekdmejik
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating the ring gear, applying threadlock, and tightening bolts.
4. Removing the crankshaft rear seal by removing bolts.
The document contains detailed step-by-step instructions, illustrations, and notes about required tools and inspection procedures.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and removing mounting bolts.
3. Removing the crankshaft rear seal by removing mounting bolts.
Detailed step-by-step instructions are provided along with illustrations to guide the process. Required tools are listed for each procedure. Precautions for handling components and proper installation techniques are also described.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...ifkkdkmdmd
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating components, applying threadlocker to bolts, and torquing bolts to specification.
4. Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...fjisejkdmd8id
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating components, applying threadlocker to bolts, and torquing bolts to specification.
4. Removing the crankshaft rear seal by removing bolts.
The document contains detailed step-by-step instructions, illustrations, and notes about required tools and inspection procedures.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f8sejdkdmdijd
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. The rear gear group, which involves removing several gears, seals, and bearings.
2. The flywheel, which requires lifting equipment and guide studs due to its weight.
3. The crankshaft rear seal, which is removed after removing the flywheel. Precise instructions are provided along with safety notices.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tools. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...yqen95561858
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...ze3xiandiao
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating components, applying threadlocker to bolts, and torquing bolts to specification.
4. Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f7usuejkdkddm3
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...ufs89eodkdmdm
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. The rear gear group, which involves removing several gears, seals, and bearings.
2. The flywheel, which requires lifting equipment and guide studs due to its weight.
3. The crankshaft rear seal, which is removed after removing the flywheel. Precise instructions are provided along with safety notices.
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
More Related Content
Similar to Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repair Manual (MTE00001 and up).pdf
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...ze3xiandiao
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f7usuejkdkddm3
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...ufs89eodkdmdm
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkskmmdmd1
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkksmemmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other gears and covers. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...ifkkdkmdmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...jjfksekdmejik
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves removing multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel, which involves cleaning, applying sealant, heating components, and torquing bolts to the specified values. Precise alignment and positioning of gears and bearings is critical.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...fjjskqazxedmmem
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures to remove the rear crankshaft seal, gear group components like gears and covers, and installing new seals and bearings in their proper positions.
2. Detailed steps and illustrations are provided to remove and install the flywheel.
3. Removal of the crankshaft rear seal is outlined, noting inspection of the crankshaft seal surface afterwards. Precautions are included to contain fluids during disassembly.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...jjfksekdmejik
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating the ring gear, applying threadlock, and tightening bolts.
4. Removing the crankshaft rear seal by removing bolts.
The document contains detailed step-by-step instructions, illustrations, and notes about required tools and inspection procedures.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and removing mounting bolts.
3. Removing the crankshaft rear seal by removing mounting bolts.
Detailed step-by-step instructions are provided along with illustrations to guide the process. Required tools are listed for each procedure. Precautions for handling components and proper installation techniques are also described.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...ifkkdkmdmd
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating components, applying threadlocker to bolts, and torquing bolts to specification.
4. Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...fjisejkdmd8id
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating components, applying threadlocker to bolts, and torquing bolts to specification.
4. Removing the crankshaft rear seal by removing bolts.
The document contains detailed step-by-step instructions, illustrations, and notes about required tools and inspection procedures.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f8sejdkdmdijd
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. The rear gear group, which involves removing several gears, seals, and bearings.
2. The flywheel, which requires lifting equipment and guide studs due to its weight.
3. The crankshaft rear seal, which is removed after removing the flywheel. Precise instructions are provided along with safety notices.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tools. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...yqen95561858
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...ze3xiandiao
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating components, applying threadlocker to bolts, and torquing bolts to specification.
4. Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f7usuejkdkddm3
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...ufs89eodkdmdm
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. The rear gear group, which involves removing several gears, seals, and bearings.
2. The flywheel, which requires lifting equipment and guide studs due to its weight.
3. The crankshaft rear seal, which is removed after removing the flywheel. Precise instructions are provided along with safety notices.
Similar to Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repair Manual (MTE00001 and up).pdf (20)
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, and hub. The assembly procedure provides steps to install 23 components in reverse order and includes checking brake clearance and installing seals and bearings. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
Caterpillar Cat M312 Excavator (Prefix 6TL) Service Repair Manual (6TL00001-0...paws21610697
This document provides the disassembly and assembly procedures for the swing drive of an M312 excavator. The disassembly procedure involves 28 steps to remove components such as the swing brake assembly, discs, plates, piston, seals, shaft, gears, bearings, and housing. The assembly procedure involves 17 steps and requires various tools to install components in the reverse order of disassembly while applying lubricant and ensuring proper torque specifications are achieved.
This document provides instructions for removing and installing engine oil filter bases and related components on Caterpillar 3304B and 3306B engines. The procedures describe removing the oil filter, oil filter base, gaskets and O-rings. Instructions are provided for disassembling the oil filter base by removing covers, bolts, springs and plungers. Reassembly and installation steps are also outlined. Tools required are listed for each procedure. Precautions are noted to keep parts clean and contain fluids.
Caterpillar Cat D250E II Articulated Truck (Prefix 4PS) Service Repair Manual...paws21610697
The document provides instructions for disassembling and assembling the piston pump used for steering on a D250E II Articulated Truck. The disassembly procedure involves removing 21 individual parts from the pump housing. The assembly procedure instructs assembling the 21 parts in the reverse order, applying lubrication and torque specifications as needed. Tools required include various drivers, pliers, and lubricants.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling a Type I governor used in Caterpillar 3114, 3116, and 3126 engines. It describes 35 steps to disassemble the governor front housing and 19 additional steps to disassemble the rear housing. Various parts are inspected for wear or damage during disassembly. Cleaning and replacement parts are also discussed. Tools required are listed.
The document provides instructions for removing and installing various engine components on a Caterpillar 3408 industrial engine, including the oil cooler, oil filter base, oil bypass valves, engine oil cooler/lines, aftercooler, and turbocharger. The procedures describe removing bolts, hoses, seals, and other parts, cleaning components, applying sealant, and reinstalling parts in reverse order.
The document provides instructions for removing and installing wheel spindles on Caterpillar articulated dump trucks. It describes removing the wheels, bearings, and seals before removing the brake shoes. It then details removing pins and springs to separate the brake shoes from the spider. Reinstallation follows the reverse order. Instructions are also given for disassembling and assembling suspension cylinders.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MTE
Configuration: 345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06931709
Gear Group (Rear) - Remove and Install
SMCS - 1206-010; 1212-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp. 1
B 1P-0510 Driver Gp 1
Start By:
a. Remove the electric starting motor.
b. Remove the flywheel.
1. Support the engine.
1/10
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g06002548
2. Remove bolts (2) and rear crankshaft seal (1).
Illustration 2 g06002556
3. Remove bolts (4) and the washers. Remove cover (3) and the seal.
Illustration 3 g06002558
4. Remove gear (7), bolts (6), and gear (5).
Illustration 4 g06002564
2/10
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 5. Remove O-ring seal (8) from gear (7).
Illustration 5 g06172622
6. Use Tooling (A) to remove bushing (7A) from gear assembly (7).
Illustration 6 g06172537
7. Remove bolts (9), adapter assembly (10), and the O-ring seal.
Illustration 7 g06172541
8. Use Tooling (B) to remove bearing (11) from adapter assembly (10).
3/10
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 8 g06172549
9. Remove gear assembly (12).
Illustration 9 g06172554
10. Remove cover (13) and the O-ring seal.
Illustration 10 g06172557
11. Use Tooling (B) to remove bearing (14).
Installation Procedure
4/10
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Table 2
Required Tools
Tool Part Number Part Description Qty
A 095-0706 Bolt 2
Illustration 11 g06172557
Illustration 12 g06172580
5/10
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 13 g06172587
1. Lower the temperature of bearing (14). Be sure to match Dimension (B) and Dimension (C)
when installing bearing (14.). Dimension (B) indicates the angle of the joint on bearing (14).
Dimension (B) is 15° ± 1°. Dimension (C) shows the distance from bearing (14) to the end
of the bore. Dimension (C) is 4.000 ± 0.500 mm (0.1575 ± 0.0197 inch).
Illustration 14 g06172554
2. Install the O-ring seal and cover (9).
6/10
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g06172597
3. Install gear assembly (12) with oil passage plug (12A) facing out.
Illustration 16 g06172601
Illustration 17 g06172609
4. Lower the temperature of bearing (11). Be sure to match Dimension (F) and Dimension (G)
when installing bearing (11) into adapter assembly (10). Dimension (F) indicates the angle
of the joint on bearing (11). Dimension (F) is 15° ± 1°. Dimension (G) shows the distance
from bearing (11) to the end of the bore. Dimension (G) is 3.500 ± 0.500 mm
(0.1378 ± 0.0197 inch).
7/10
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 18 g06172537
5. Install the O-ring seal, adapter assembly (10), and bolts (9).
Illustration 19 g06172619
6. Lower the temperature of bearing (7A). Install bearing (7A) into gear assembly (7). Be sure
that each relief (H) is within 2° of each relief in gear assembly (7).
Illustration 20 g06002564
7. Install O-ring seal (8) onto gear (7).
8/10
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 21 g06002578
8. Install gear (5) and bolts (6).
Note: Tooling (A) is for supporting gear (7) during the installation of the cover and the rear
crankshaft seal.
Note: The bolt holes in gear (7) are not symmetrical. When installing Tooling (C), check
the rest of the bolts holes in gear (7) are aligned with the holes in the crankshaft.
9. Install gear (7) and Tooling (C).
Illustration 22 g06002581
10. Install cover (3), the seal, bolts (4), and the washers.
9/10
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g06002592
11. Install rear crankshaft seal (1) and bolts (2).
12. Remove Tooling (C).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 22 13:56:43 UTC+0800 2020
10/10
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 En...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MTE
Configuration: 345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249234
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B FT2712 Guide Stud 1
1/2
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g01132214
1. Attach Tooling (A) and a suitable lifting device to flywheel (2). The weight of flywheel (2)
is approximately 79 kg (175 lb).
2. Remove top bolt (1). Install Tooling (B).
3. Remove remaining bolts (1).
4. Remove flywheel (2).
5. Use a hammer and a punch in order to remove the ring gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 22 13:57:40 UTC+0800 2020
2/2
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MTE
Configuration: 345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06123534
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B FT2712 Guide Stud 1
C - Loctite 242 1
Always wear protective gloves when handling parts that have been
heated.
1. Raise the temperature of the ring gear. Position the ring gear with the part number toward
the crankshaft. Install the ring gear on the flywheel. Allow the ring gear to cool. Use a soft
hammer in order to seat the ring gear against the shoulder of the flywheel.
1/2
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g01132214
2. Attach Tooling (A) and a suitable lifting device to flywheel (2) . The weight of flywheel (2)
is approximately 79 kg (175 lb).
3. Position flywheel (2) on Tooling (B) .
4. Apply Tooling (C) to bolts (1) .
5. Install bolts (1) . Remove Tooling (B) . Install remaining bolt (1) . Tighten the bolts evenly
to a torque of 300 ± 40 N·m (221 ± 30 lb ft).
6. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect" for the
correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 22 13:58:37 UTC+0800 2020
2/2
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MTE
Configuration: 345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06010889
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01132235
1. Remove bolts (1).
2. Remove crankshaft rear seal (2).
Note: Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual Inspection and
Magnetic Particle Inspection" for the correct inspection procedure of the crankshaft seal surface.
Note: Refer to Reuse and Salvage Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9,
C-9, C10, C11, C12, C-12, C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the
correct specifications of the crankshaft.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 22 13:59:34 UTC+0800 2020
2/2
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MTE
Configuration: 345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06010890
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 Primer N -
B - Loctite 620 Retaining Compound -
C 147-2675 Wear Sleeve Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g01140085
Illustration 2 g03698745
Numerical tightening sequence for bolts (2).
Note: If required, install a crankshaft wear sleeve at engine overhaul. For more information
please refer to the following Reuse and Salvage Guidelines. Refer to Reuse and Salvage
Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9, C-9, C10, C11, C12, C-12,
2/3
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the correct specifications
of the crankshaft. Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual
Inspection and Magnetic Particle Inspection" for the correct inspection procedure of the
crankshaft seal surface.
1. If a crankshaft wear sleeve is necessary, refer to Step 1.a through Step 1.d to install the
crankshaft wear sleeve. If a crankshaft wear sleeve is not necessary, refer to Step 2.
a. Clean and polish the crankshaft of imperfections.
b. Use Tooling (A) to clean the outside diameter of the crankshaft and the inside
diameter of the crankshaft wear sleeve.
c. Apply Tooling (B) to the outside diameter of the crankshaft and the inside diameter of
the crankshaft wear sleeve.
d. Use Tooling (C) to install the crankshaft wear sleeve.
Note: Leave the shipping sleeve in place to install the crankshaft rear seal. The crankshaft
rear seal must be installed dry.
Note: If the seal group, O-ring seal, and the shipping sleeve are separated, these
components should not be used.
2. Lubricate the O-ring seal with clean engine oil that is on the back of the crankshaft rear seal
(1).
3. Position crankshaft rear seal (1) and the shipping sleeve over the crankshaft. Push
crankshaft rear seal (1) in place to dislodge the shipping sleeve.
Note: Do not remove the shipping sleeve until bolts (2) are installed.
4. Install new bolts (2) hand tight. Then, tighten bolts (2) in numerical sequence, shown in
Illustration 2. Tighten bolts (2) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 22 14:00:31 UTC+0800 2020
3/3
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MTE
Configuration: 345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249340
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
1. Support the engine.
Illustration 1 g01132273
1/3
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2)
is approximately 62 kg (137 lb).
3. Remove bolts (1) and flywheel housing (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8846 Gasket Sealant 1
1. Apply Tooling (A) to the face of the cylinder block.
Illustration 2 g01132273
2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2)
is approximately 62 kg (137 lb). Position flywheel housing (2) on the rear of the cylinder
block.
3. Install bolts (1).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Wed Jul 22 14:01:27 UTC+0800 2020
2/3
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MTE
Configuration: 345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249982
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
1/3
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g01132580
1. Remove belt (1).
2. Attach a suitable lifting device to crankshaft vibration damper and pulley (3). The weight of
crankshaft vibration damper and pulley (3) is approximately 27 kg (60 lb). Remove bolts
(2).
3. Remove crankshaft vibration damper and pulley (3).
Installation Procedure
2/3
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 2 g01132580
1. Attach a suitable lifting device to crankshaft vibration damper and pulley (3). The weight of
crankshaft vibration damper and pulley (3) is approximately 27 kg (60 lb). Position
crankshaft vibration damper and pulley (3) on the engine.
2. Install bolts (2).
3. Install belt (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 22 14:02:24 UTC+0800 2020
3/3
345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...