This document provides instructions for disassembling and assembling the travel motor of a 345B II Excavator. Key steps include:
1. Cleaning all parts to prevent contamination of the hydraulic system.
2. Removing components like the head, plates, seals and pistons from the travel motor housing.
3. Separating additional components in the rotating group and barrel.
4. Inspecting all parts and replacing any that are worn or damaged.
5. Reassembling the components in reverse order, making sure to clean parts and apply new seals and O-rings throughout. Proper orientation and torque specifications are critical.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...zatao0179249295
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the rotating group including installing piston assemblies, bearings and other parts back onto the shaft assembly.
3. Measuring clearances and installing spacers to the proper specifications.
The instructions emphasize cleaning parts and applying lubricants before assembly to prevent contaminating the hydraulic system.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...zatao0179249295
This document provides instructions for disassembling and assembling the travel motor on Models 345B and 345B L Series II Excavators. It outlines 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and rotating group. It also lists the required tools and safety notices for the job. The summary is meant to give a high-level overview of the key details while being brief.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...luanxianshi27
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the barrel assembly including installing washers, spacers, piston assemblies and retainer.
3. Installing the cam plate and bearing onto the shaft and assembling the rotating group.
The instructions provide detailed illustrations and specify the proper orientation and torque specifications for each component. Cleanliness of parts and applying lubricant is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...luanxianshi27
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the rotating group including installing piston assemblies, bearings and other parts.
3. Measuring clearances during assembly to ensure correct orientation and fit of parts.
The instructions emphasize cleaning parts and applying lubricant before assembly to prevent contamination of hydraulic systems. Notes provide additional guidance on inspecting parts and using new components when required.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...wfu089267
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the barrel assembly including installing washers, spacers, piston assemblies and retainer.
3. Installing the cam plate and bearing onto the shaft and assembling the rotating group.
The instructions provide detailed illustrations and specify the proper orientation and torque specifications for each component. Cleanliness of parts and applying lubricant is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...wfu089267
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the barrel assembly including installing washers, spacers, piston assemblies and retainer.
3. Installing the cam plate and bearing onto the shaft and assembling the rotating group.
The instructions provide detailed illustrations and specify torque settings for assembling the various components in the correct orientation and order. Cleaning and inspection of parts is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 345B Series II Excavator (Prefix AKX) Service Repair Manual (...zatao0179249295
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345B L Series II Excavator (Prefix AKX) Service Repair Manual...zatao0179249295
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...zatao0179249295
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the rotating group including installing piston assemblies, bearings and other parts back onto the shaft assembly.
3. Measuring clearances and installing spacers to the proper specifications.
The instructions emphasize cleaning parts and applying lubricants before assembly to prevent contaminating the hydraulic system.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...zatao0179249295
This document provides instructions for disassembling and assembling the travel motor on Models 345B and 345B L Series II Excavators. It outlines 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and rotating group. It also lists the required tools and safety notices for the job. The summary is meant to give a high-level overview of the key details while being brief.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...luanxianshi27
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the barrel assembly including installing washers, spacers, piston assemblies and retainer.
3. Installing the cam plate and bearing onto the shaft and assembling the rotating group.
The instructions provide detailed illustrations and specify the proper orientation and torque specifications for each component. Cleanliness of parts and applying lubricant is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...luanxianshi27
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the rotating group including installing piston assemblies, bearings and other parts.
3. Measuring clearances during assembly to ensure correct orientation and fit of parts.
The instructions emphasize cleaning parts and applying lubricant before assembly to prevent contamination of hydraulic systems. Notes provide additional guidance on inspecting parts and using new components when required.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...wfu089267
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the barrel assembly including installing washers, spacers, piston assemblies and retainer.
3. Installing the cam plate and bearing onto the shaft and assembling the rotating group.
The instructions provide detailed illustrations and specify the proper orientation and torque specifications for each component. Cleanliness of parts and applying lubricant is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...wfu089267
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the barrel assembly including installing washers, spacers, piston assemblies and retainer.
3. Installing the cam plate and bearing onto the shaft and assembling the rotating group.
The instructions provide detailed illustrations and specify torque settings for assembling the various components in the correct orientation and order. Cleaning and inspection of parts is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 345B Series II Excavator (Prefix AKX) Service Repair Manual (...zatao0179249295
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345B L Series II Excavator (Prefix AKX) Service Repair Manual...zatao0179249295
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345B L Series II Excavator (Prefix AKX) Service Repair Manual...luanxianshi27
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345B Series II Excavator (Prefix AKX) Service Repair Manual (...luanxianshi27
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It begins by listing the required tools. The disassembly process involves removing 31 individual parts from the travel motor in a specific sequence. The assembly section then provides instructions for reinstalling the parts in the reverse order, noting proper installation of seals, washers, and other components. Safety notices are included regarding cleanliness, contamination prevention, and inspection of parts.
Caterpillar Cat 345B Series II Excavator (Prefix AKX) Service Repair Manual (...wfu089267
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps to disassemble the travel motor by removing components like the head, rotating group, brake piston, plates and seals. It then lists 29 steps to reassemble the travel motor by installing components in the reverse order, and provides notes about cleaning, lubricating and replacing parts as needed. Tools required are also listed.
Caterpillar Cat 345B L Series II Excavator (Prefix AKX) Service Repair Manual...wfu089267
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs to reverse the disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f8uesjdkdmdm
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs to reverse the disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
Caterpillar cat 345 c excavator (prefix tba) service repair manual (tba00001 ...fjkkekmdm
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs to reverse the disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. It notes to mark parts locations and clean components. Reassembly follows the reverse order, noting to reinstall parts in their original locations and orientations. Proper cleaning is important to prevent contaminating the hydraulic system.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...yqen95561858
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...ze3xiandiao
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar cat 345 c l excavator (prefix tba) service repair manual (tba0000...ifkkdkmdmd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs reversing the 31 disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and other attachments, and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and other parts are then removed to separate the outside housing from the rotor.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
This document provides instructions for removing and installing the final drive and travel motor on 330D L and 330D N Hydraulic Excavators. The removal procedure involves separating the track, disconnecting hydraulic lines, and removing mounting bolts to lift the final drive and travel motor assembly out. The installation procedure specifies cleaning and inspecting parts, attaching components in the reverse order of removal, and refilling the hydraulic system. Tools and safety precautions are also listed.
Caterpillar Cat 330-A L EXCAVATOR (Prefix 9ML) Service Repair Manual (9ML0000...f8usiedkdmm
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...f8usiedkdmm
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
More Related Content
Similar to Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual (ALB00001 and up).pdf
Caterpillar Cat 345B L Series II Excavator (Prefix AKX) Service Repair Manual...luanxianshi27
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345B Series II Excavator (Prefix AKX) Service Repair Manual (...luanxianshi27
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It begins by listing the required tools. The disassembly process involves removing 31 individual parts from the travel motor in a specific sequence. The assembly section then provides instructions for reinstalling the parts in the reverse order, noting proper installation of seals, washers, and other components. Safety notices are included regarding cleanliness, contamination prevention, and inspection of parts.
Caterpillar Cat 345B Series II Excavator (Prefix AKX) Service Repair Manual (...wfu089267
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps to disassemble the travel motor by removing components like the head, rotating group, brake piston, plates and seals. It then lists 29 steps to reassemble the travel motor by installing components in the reverse order, and provides notes about cleaning, lubricating and replacing parts as needed. Tools required are also listed.
Caterpillar Cat 345B L Series II Excavator (Prefix AKX) Service Repair Manual...wfu089267
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs to reverse the disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f8uesjdkdmdm
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs to reverse the disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
Caterpillar cat 345 c excavator (prefix tba) service repair manual (tba00001 ...fjkkekmdm
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs to reverse the disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. It notes to mark parts locations and clean components. Reassembly follows the reverse order, noting to reinstall parts in their original locations and orientations. Proper cleaning is important to prevent contaminating the hydraulic system.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...yqen95561858
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...ze3xiandiao
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar cat 345 c l excavator (prefix tba) service repair manual (tba0000...ifkkdkmdmd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs reversing the 31 disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
Similar to Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual (ALB00001 and up).pdf (17)
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and other attachments, and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and other parts are then removed to separate the outside housing from the rotor.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
This document provides instructions for removing and installing the final drive and travel motor on 330D L and 330D N Hydraulic Excavators. The removal procedure involves separating the track, disconnecting hydraulic lines, and removing mounting bolts to lift the final drive and travel motor assembly out. The installation procedure specifies cleaning and inspecting parts, attaching components in the reverse order of removal, and refilling the hydraulic system. Tools and safety precautions are also listed.
Caterpillar Cat 330-A L EXCAVATOR (Prefix 9ML) Service Repair Manual (9ML0000...f8usiedkdmm
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...f8usiedkdmm
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 3YR) Service Repair Manual (3YR00001...f8usiedkdmm
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 385C L Excavator (Prefix JCM) Service Repair Manual (JCM00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. It cautions to check all O-rings and seals for wear and replace if needed.
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
The document provides instructions for removing and installing valve components on a Caterpillar C-18 engine, including:
1) Removal and installation procedures for the variable valve actuator, requiring removal of the valve mechanism cover and disconnection of electrical harnesses.
2) Removal of the rocker arm assembly by removing mounting bolts and studs and lifting it out as a unit.
3) Disassembly of individual rocker arms by removing adjustment screws, buttons, and O-rings.
4) Reassembly of rocker arms and installation of the rocker arm assembly by positioning it, installing mounting hardware, and adjusting valves and injectors.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Removing the valve cover, rocker arm and shaft, cylinder head, and other components. Cleaning and inspecting parts during removal.
- Installing components by reversing the removal procedures, applying anti-seize compound, adjusting clearances, and reconnecting wiring harnesses and fluid lines.
- Detailed steps include using lifting tools to handle heavy parts like the cylinder head, removing and tightening bolts in a specific sequence, and ensuring proper reinstallation of identification marks and plugs on disconnected lines.
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. It begins with removing the final drive and describes dismantling it into individual parts like the ring gear, carrier assemblies, planetary gears and shafts. Alignment marks are noted to aid reassembly. The instructions then describe assembling the final drive components back into the final drive housing.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f8usiedkdmm
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear, sun gear, and other large internal components from the swing drive housing.
Caterpillar Cat 345C Mobile Hydraulic Excavator (Prefix M3E) Service Repair M...f8usiedkdmm
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, seals and other components. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the reverse order of disassembly. Contamination of hydraulic systems must be avoided during the process.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and tightening sequences are provided. The installation ends by installing a crankshaft rear seal.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM0000...f8usiedkdmm
The document provides instructions for removing and installing various engine components, including:
1) Removing the cylinder head which involves first removing the fuel injection lines and exhaust manifold.
2) Instructions for disassembling the rocker shaft which includes removing rocker arms, springs, and supports.
3) Procedures for assembling the rocker shaft by installing the rocker arms, supports, springs and securing with a pin and plugs.
Caterpillar Cat 329F L Excavator (Prefix ERL) Service Repair Manual (ERL00001...f8usiedkdmm
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
The document provides instructions for removing and installing various components of a Caterpillar C7.1 engine, including the vibration damper and pulley, crankshaft front seal, and front cover. The removal procedures involve using various tools to remove screws, bolts, seals and other parts. The installation procedures specify cleaning components, installing new seals and gaskets, and tightening bolts to the specified torques.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
Caterpillar Cat 385C L MH EXCAVATOR (Prefix WAW) Service Repair Manual (WAW00...f8usiedkdmm
This document provides instructions for removing and installing fuel system components on a Caterpillar 385C L MH EXCAVATOR. The components include the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors. The procedures describe disconnecting hoses, removing mounting bolts, and using various tools to properly remove and install each component while keeping parts clean and free of contaminants.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline for Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
1. Thoroughly clean the outside of the travel motor prior to disassembly. Fasten the travel
motor to a suitable holding fixture in a vertical position. The weight of the travel motor is
141 kg (310 lb).
Illustration 1 g00627438
2. Remove displacement change valve (1) from the head of the travel motor.
3/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g00624938
3. Remove three O-ring seals (2) and two rings (3) from the displacement change valve.
Illustration 3 g00628657
4. Remove three plugs (5) from the head. Remove an O-ring seal from each plug.
5. Remove six outer bolts (4) from the head of the travel motor.
Illustration 4 g00624949
4/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 6. Use Tooling (A) and a suitable lifting device to remove the head of the travel motor from
the travel motor housing. The head weighs 43 kg (95 lb).
Note: There are three pins (7) that may fall out of the inside of the head when the head is
removed.
Note: Be careful during the removal of head (6) from the travel motor housing. Be careful
not to scratch mating surfaces or damage the mating surfaces of the components.
Illustration 5 g00624953
7. Turn over the head. If three pins (7) are in the bottom side of the head, remove the pins.
Illustration 6 g00627405
8. Remove port plate (8) and O-ring seal (9) from the head.
5/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g00625967
9. Use Tooling (B) in order to remove bearing (10) from the head of the travel motor.
Illustration 8 g00627391
10. Remove plate (11) and remove springs (12) from the travel motor housing.
11. Remove O-ring seals (13) from the upper surface of the travel motor housing.
Illustration 9 g00627377
6/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 12. Install Tooling (C) on the brake piston (14). Remove the brake piston.
Illustration 10 g00625888
13. Remove O-ring seals (15) and the backup rings from the brake piston.
Note: Make sure that you take note of the location of the O-rings versus the backup rings.
Illustration 11 g00625891
14. Remove six separator plates (16) from the travel motor housing.
7/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 12 g00666743
15. Remove five friction disks (17) from the travel motor housing.
Illustration 13 g00626837
16. Install Tooling (D) to the shaft and use a suitable lifting device in order to remove the
rotating group from the travel motor housing. The weight of the rotating group is 29 kg (65
lb).
Note: Do not allow the components of the rotating group to come apart during the removal
from the travel motor. All of the components in the rotating group must be reinstalled in the
component's original location.
8/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00626633
17. Turn over the rotating group. Remove shaft assembly (18) from the rotating group.
Illustration 15 g00666621
Illustration 16 g00625900
18. Use a suitable press to remove bearing (19) from shaft (18) .
9/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g00666622
19. Use Tool (E) and a suitable press in order to remove inner race (20) from shaft (18) .
Illustration 18 g00625908
20. Remove cam plate (21) from the rotating group.
Illustration 19 g00625911
10/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 21. Retainer (22) and piston assemblies (23) are not serviced separately. Prior to the removal of
the retainer and the piston assemblies from barrel (24), put identification marks on the
piston assemblies, the retainer and the barrel for assembly purposes.
22. The piston assemblies must be reinstalled in the original bores in the retainer and the barrel.
23. Remove retainer (22) and piston assemblies (23) from barrel (24) .
24. Separate the piston assemblies from the retainer.
Illustration 20 g00625917
Note: The orientation of the four washers (25) is important. The four washers must be
reinstalled on barrel (24) in the same orientation.
25. Remove guide (26) and outer spacer (27) from barrel (24) .
26. Remove four washers (25) and inner spacer (28) from the barrel.
Illustration 21 g00625937
27. Remove two keys (29) from the travel motor housing.
11/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 22 g00625920
28. Use Tooling (F) to remove retaining ring (30) from the shaft end of the travel motor
housing.
Illustration 23 g00625936
Illustration 24 g00636454
29. Use Tooling (G) to remove lip type seal (31) from the travel motor housing if the shaft has
been removed from the travel motor.
12/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 30. Use Tooling (H) to remove lip type seal (31) if the shaft has not been removed from the
travel motor. Place the travel motor in a vertical position when you use Tooling (H) to
remove the lip type seal.
Illustration 25 g00625976
31. Remove plug (33) and piston (32) from the travel motor housing. Remove O-ring seal (34)
from the plug.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 17:46:18 UTC+0800 2020
13/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B II EXCAVATOR ALB
Configuration: 345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
345B, 345B Series II and W345B Series II Excavators Machine Systems
Media Number -SENR1934-11 Publication Date -01/01/2012 Date Updated -12/01/2012
i01324820
Travel Motor - Assemble - Series II
SMCS - 4351-016
S/N - AGS1-UP
S/N - AKJ1-UP
S/N - AKX1-UP
S/N - ALB1-UP
S/N - ALD1-UP
S/N - AMD1-UP
S/N - AMJ1-UP
S/N - AMN1-UP
S/N - APB1-UP
S/N - AYR1-UP
S/N - CCC1-UP
S/N - DCW1-UP
S/N - DET1-UP
S/N - FEE1-UP
Assembly Procedure
Table 1
1/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Required Tools
Tool Part Number Part Description Qty
(A) 180-6533 Seal Driver 1
(B) 6V-7030 Micrometer Depth Gauge 1
(C) 8T-0447 Calipers 1
(D) 4C-8359 Eyebolt 1
(E) 1P-0510 Driver Group 1
(F) 3E-3879 Eyebolt 1
(G) 1P-1862 Pliers 1
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline For Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound during the
assembly procedure.
Note: Apply a light film of "10W" oil to all components before assembly.
2/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00631019
1. Install O-ring seal (36) on plug (35) .
2. Install piston (34) and the plug in the travel motor body. Tighten the plug to a torque of 430
± 40 N·m (317 ± 30 lb ft).
Illustration 2 g00630992
Illustration 3 g00636553
3/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 3. Apply a thin coat of 4C-4030 Thread Lock Compound on the outer surfaces of lip type seal
(33) .
4. Use Tooling (A) and a suitable hammer to drive the lip type seal into the travel motor body.
Drive the seal downward until Tooling (A) makes contact with the travel motor housing.
5. Use Tooling (G) to install retaining ring (32) to the shaft end of the travel motor body.
Illustration 4 g00630986
6. Install two keys (31) inside the travel motor body.
Illustration 5 g00629434
7. Assemble washers (29), inner spacer (30) and outer spacer (28) in the proper orientation, as
shown.
4/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 6 g00628110
8. Use Tooling (B) to measure the distance from the outer spacer to the surface of the table.
The distance should be 22.1 ± 0.6 mm (0.87 ± 0.02 inch). If this measurement is off, check
orientation of the washers. If orientation is correct, replace washers and spacers with new
parts.
Illustration 7 g00625917
9. Install inner spacer (28), four washers (25), and outer spacer (27) to barrel (24) .
10. Install guide (26) to the barrel.
5/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 8 g00625911
11. Install piston assemblies (23) with retainer (22) in the piston assembly's original bore in
barrel (24) .
Illustration 9 g00625908
12. Install cam plate (21) on the barrel assembly.
Illustration 10 g00666621
6/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 11 g00628062
13. Use a suitable press to install bearing (19) onto shaft (18) .
Illustration 12 g00668076
14. Use a suitable press in order to install inner race (20) onto shaft (18) .
Note: Place the two support plates under the lip of shaft (18) .
7/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 13 g00626633
15. Insert shaft (18) in the barrel assembly.
Illustration 14 g00625891
Illustration 15 g00666743
16. Alternate five friction disks (17) and six separator plates (16) into the travel motor housing.
Start with a separator plate and end with a separator plate.
8/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 16 g00626837
17. Attach Tooling (D) to the shaft. Use a suitable lifting device in order to place barrel
assembly into the travel motor body.
Note: Align the notches of the cam plate with the keys in the travel motor body before you
lower the barrel assembly into the travel motor body.
Illustration 17 g00628965
18. Use Tooling (C) to measure the depth from the top surface of the travel motor body to the
bronze face of the barrel assembly. The distance should be 38 ± 2 mm (1.5 ± 0.08 inch). If
this measurement is off, check orientation of the barrel assembly. Also check if the cam
plate is properly seated on the keys.
9/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 18 g00625888
Illustration 19 g00667938
(15) O-Ring seals
10/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 19. Install O-ring seals (15) and the backup rings on the brake piston.
Note: Make sure that you install the backup ring and the O-ring seal in the original position.
Refer to Illustration 19.
Illustration 20 g00629015
20. Install brake piston (14) in the body of the travel motor by hand. It may be necessary to use
a soft faced hammer to seat the brake piston correctly.
Illustration 21 g00629060
21. Use Tooling (C) to measure the distance from the top of the brake piston (14) to the top
surface of the travel motor body. The distance should be 20.8 ± 1 mm (0.82 ± 0.04 inch). If
this measurement is off, drive the brake piston further into the travel motor body.
11/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 22 g00627391
22. Install springs (12) and plate (11) .
23. Install O-ring seals (13) .
Illustration 23 g00629646
24. Use Tooling (E) to drive the bearing into the head.
Illustration 24 g00627405
12/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 25. Install O-ring seal (9) onto the head.
26. Install port plate (8) on the head. It may be necessary to apply a small amount of grease to
the port plate in order to hold the port plate in place during the installation of the head.
Illustration 25 g00629613
27. Turn over head (6). Install Tooling (F) onto the head. Use a suitable lifting device to install
the head onto the travel motor.
Illustration 26 g00631594
28. Install three dowels (7) into the head.
13/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...