The document provides instructions for disassembling and assembling the travel motor on a 345B Excavator model. It lists required tools and parts and gives step-by-step instructions to remove components like the brake cover, brake assembly, springs, seals, gears, and housing parts. Special safety precautions are outlined and components must be cleaned, marked, and reinstalled in their original locations. Detailed illustrations accompany each step.
Caterpillar cat 345 b track type excavator (prefix 5ws) service repair manual...jfdskekdmme
The document provides instructions for removing and installing cylinder head components on a Caterpillar 3176C engine, including:
1) Removal steps such as removing sensors, tubes, bolts and the cylinder head using a lifting device.
2) Installation steps such as cleaning surfaces, installing new gaskets and O-rings, installing the cylinder head using a lifting device, and torquing bolts to the specified value.
3) The document provides illustrations of the components and tools needed to correctly perform the removal and installation.
Caterpillar cat 345 b excavator (prefix 9gs) service repair manual (9gs00001 ...f8isoeidkdk
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator engines. The removal procedure involves removing various components like sensors, tubes, and manifolds. The cylinder head is then removed using lifting equipment. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening the cylinder head bolts in a specific sequence to the correct torques.
Caterpillar cat 345 b l series ii excavator (prefix alb) service repair manua...jfdskekdmme
This document provides instructions for disassembling and assembling the travel motor of a 345B II Excavator. Key steps include:
1. Cleaning all parts to prevent contamination of the hydraulic system.
2. Removing components like the head, plates, seals and pistons from the travel motor housing.
3. Separating additional components in the rotating group and barrel.
4. Reassembling components like pistons, seals and plates back into the travel motor housing in reverse order. Cleanliness is important to prevent hydraulic system contamination.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. The removal procedure involves disconnecting various sensors and tubes, and removing bolts and gaskets. The installation procedure describes cleaning surfaces, installing new gaskets and bolts, and tightening the bolts in a specific sequence to the correct torques. Replacing damaged threads with Heli-Coils is also described.
Caterpillar cat 345 b ii excavator (prefix fee) service repair manual (fee000...f8isoeidkdk
This document provides instructions for assembling the swing drive of a 345B II excavator. Key steps include:
1. Cleaning and inspecting all parts before assembly.
2. Applying anti-seize compound and installing bearings and seals in the swing drive housing.
3. Heating and installing bearings on the pinion shaft and spacer.
4. Using a press to install the pinion shaft, bearings, and bearing cage into the swing drive housing.
Caterpillar cat 349 d l mobile hydraulic excavator (prefix dkn) service repai...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like the displacement change valve and head. Internal components like the brake piston, disks, and rotating group are then removed. Individual parts in the rotating group like the piston assemblies and barrel are also taken apart. The assembly instructions reverse the disassembly process and provide details on cleaning, lubricating, and installing parts in their proper positions and with the correct torque specifications.
Caterpillar cat 345 b lc excavator (prefix 7ks) service repair manual (7ks000...jfdskekdmme
The document provides instructions for disassembling and assembling the travel motor on 345B excavator models. It is a 15-step process that includes removing components like the brake cover, brake assembly, springs, seals, gears, and housing parts. Special tools are required and technicians must follow the steps carefully to avoid damaging parts and ensure proper reassembly.
Caterpillar cat 349 f excavator (prefix hpd) service repair manual (hpd00001 ...fjsjjekdkme
The document provides instructions to disassemble a travel motor over 27 steps. It begins by draining the motor and removing external components like plugs, seals, and the motor head assembly. Internally, it describes removing the barrel assembly, piston assemblies, separator and friction plates, springs, and swashplate. Safety notices are provided throughout to warn of potential spring hazards and to mark components for proper reassembly.
Caterpillar cat 345 b track type excavator (prefix 5ws) service repair manual...jfdskekdmme
The document provides instructions for removing and installing cylinder head components on a Caterpillar 3176C engine, including:
1) Removal steps such as removing sensors, tubes, bolts and the cylinder head using a lifting device.
2) Installation steps such as cleaning surfaces, installing new gaskets and O-rings, installing the cylinder head using a lifting device, and torquing bolts to the specified value.
3) The document provides illustrations of the components and tools needed to correctly perform the removal and installation.
Caterpillar cat 345 b excavator (prefix 9gs) service repair manual (9gs00001 ...f8isoeidkdk
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator engines. The removal procedure involves removing various components like sensors, tubes, and manifolds. The cylinder head is then removed using lifting equipment. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening the cylinder head bolts in a specific sequence to the correct torques.
Caterpillar cat 345 b l series ii excavator (prefix alb) service repair manua...jfdskekdmme
This document provides instructions for disassembling and assembling the travel motor of a 345B II Excavator. Key steps include:
1. Cleaning all parts to prevent contamination of the hydraulic system.
2. Removing components like the head, plates, seals and pistons from the travel motor housing.
3. Separating additional components in the rotating group and barrel.
4. Reassembling components like pistons, seals and plates back into the travel motor housing in reverse order. Cleanliness is important to prevent hydraulic system contamination.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. The removal procedure involves disconnecting various sensors and tubes, and removing bolts and gaskets. The installation procedure describes cleaning surfaces, installing new gaskets and bolts, and tightening the bolts in a specific sequence to the correct torques. Replacing damaged threads with Heli-Coils is also described.
Caterpillar cat 345 b ii excavator (prefix fee) service repair manual (fee000...f8isoeidkdk
This document provides instructions for assembling the swing drive of a 345B II excavator. Key steps include:
1. Cleaning and inspecting all parts before assembly.
2. Applying anti-seize compound and installing bearings and seals in the swing drive housing.
3. Heating and installing bearings on the pinion shaft and spacer.
4. Using a press to install the pinion shaft, bearings, and bearing cage into the swing drive housing.
Caterpillar cat 349 d l mobile hydraulic excavator (prefix dkn) service repai...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like the displacement change valve and head. Internal components like the brake piston, disks, and rotating group are then removed. Individual parts in the rotating group like the piston assemblies and barrel are also taken apart. The assembly instructions reverse the disassembly process and provide details on cleaning, lubricating, and installing parts in their proper positions and with the correct torque specifications.
Caterpillar cat 345 b lc excavator (prefix 7ks) service repair manual (7ks000...jfdskekdmme
The document provides instructions for disassembling and assembling the travel motor on 345B excavator models. It is a 15-step process that includes removing components like the brake cover, brake assembly, springs, seals, gears, and housing parts. Special tools are required and technicians must follow the steps carefully to avoid damaging parts and ensure proper reassembly.
Caterpillar cat 349 f excavator (prefix hpd) service repair manual (hpd00001 ...fjsjjekdkme
The document provides instructions to disassemble a travel motor over 27 steps. It begins by draining the motor and removing external components like plugs, seals, and the motor head assembly. Internally, it describes removing the barrel assembly, piston assemblies, separator and friction plates, springs, and swashplate. Safety notices are provided throughout to warn of potential spring hazards and to mark components for proper reassembly.
Caterpillar cat 335 f lcr excavator (prefix kne) service repair manual (kne00...f8isoeidkdk
This document provides instructions for removing the cylinder head from a Caterpillar C7.1 engine. It involves the following steps:
1. Draining coolant and disconnecting hoses and wiring harnesses from sensors
2. Removing brackets and tubes attached to the cylinder head
3. Gradually loosening the bolts holding the cylinder head in reverse numerical order
4. Removing the bolts and lifting the cylinder head off using a lifting device
The purpose is to remove the cylinder head from the engine for maintenance or repair while taking precautions to contain fluids and correctly support the heavy cylinder head.
Caterpillar cat 345 b excavator (prefix 4ss) service repair manual (4ss00001 ...f8isoeidkdk
This document provides instructions for disassembling and assembling the travel motor on 345B and 345B L Excavator models. It lists required tools and safety notices, then provides 32 detailed steps for disassembly, including removing components like the brake assembly, barrel assembly, and swashplate assembly. It concludes with 14 steps for reassembling components like the shaft assembly, swashplate assembly, and installing bearings and bushings back into the motor housing. Care is advised to keep parts clean and in their original locations during disassembly and reassembly.
Caterpillar cat 345 c l excavator (prefix s5m) service repair manual (s5m0000...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly procedure involves removing over 20 components of the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs to clean all parts, apply anti-seize compound, install bearing cups and cones, and adjust the bearing preload using shims to achieve the proper load. Precise positioning of identification marks is required to reinstall parts in their original locations.
Caterpillar cat 345 c hcr material handler excavator (prefix mte) service rep...jfdskekdmme
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. The removal procedure involves removing bolts and seals to access the rear gear components. Tools are required to remove bearings from assemblies. The installation procedure specifies cleaning parts and applying threadlock before installing components in the reverse order of removal, ensuring proper bearing alignment and torque specifications are followed.
Caterpillar cat 345 b l series ii excavator (prefix akx) service repair manua...jfdskekdmme
This document provides disassembly and assembly instructions for the travel motor on Caterpillar 345B and 345B L Series II Excavators. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pistons, and housing. It also provides lubrication and installation instructions for assembling the travel motor. Proper assembly requires using the correct tools and ensuring parts are clean before reinstalling them in their original locations and orientations.
Caterpillar cat 349 f excavator (prefix tew) service repair manual (tew00001 ...fjsjjekdkme
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavators.
2. It describes removing over 30 components of the travel motor in sequential order, including plugs, springs, pistons, plates, seals, and more.
3. Precautions are provided to protect against spring forces and ensure components are reinstalled in their original positions and order.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 336 e hvg excavator (prefix rbs) service repair manual (rbs00...f8isoeidkdk
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
Caterpillar cat 345 b l excavator (prefix bfg) service repair manual (bfg0000...jfdskekdmme
This document provides instructions for disassembling and assembling the travel motor on 345B excavator models. It lists required tools and parts. The procedure involves 32 steps for disassembly, including removing the brake assembly, barrel assembly, and swashplate assembly. Assembly is the reverse of disassembly with notes to clean parts and apply lubricant before reinstalling. Safety notices are provided to contain fluids and prevent contamination.
Caterpillar cat 345 b l series ii excavator (prefix ags) service repair manua...jfdskekdmme
The document provides step-by-step instructions for disassembling and assembling the final drive components of an excavator. It describes removing components like the travel motor, final drive, carrier assemblies, ring gear, and more. It then describes assembling the components in reverse order, including pressing in bearing cups, installing bearing cones with the proper preload using shims, and reinstalling components like the sprocket housing and coupling gear. Precise tools and lifting devices are required to handle the heavy components.
Caterpillar cat 345 b excavator (prefix amj) service repair manual (amj00001 ...fjsekdmmeed
This document provides assembly instructions for installing a travel motor on a 345B Excavator. It outlines 33 steps to assemble parts like seals, pistons, plates, and shafts inside the travel motor housing. It then describes 4 steps to install the assembled travel motor onto the final drive, including cleaning surfaces, replacing an O-ring seal, and using lifting tools to maneuver the motor into position. Proper torque specifications are given for tightening fasteners.
Caterpillar cat 345 c l excavator (prefix scn) service repair manual (scn0000...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly process involves removing over 20 individual parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly section outlines installing new seals, pressing in bearing cups, adjusting shims to set proper bearing preload, and reinstalling all parts in reverse order. Precise positioning of stamped identification marks on gears is required for correct reassembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...cdsaas
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly process reverses the disassembly steps and includes applying sealant and pressing components together using various tools.
Caterpillar cat 345 c hydraulic excavator (prefix tdg) service repair manual ...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 13 steps for assembly, replacing components in reverse order and noting to clean all parts, apply lubricant, and measure clearances during assembly to ensure proper operation. Tools required are listed for both disassembly and assembly.
Caterpillar cat 340 f excavator (prefix rbd) service repair manual (rbd00001 ...fjsekdmmeed
This document provides instructions for removing and installing the fuel manifold (rail) on a C9.3 engine. The removal procedure involves disconnecting harness assemblies, tube assemblies, and removing bolts to access the fuel manifold. Sensors, solenoid valves, and other components are then removed from the manifold. Installation is the reverse of removal, with all components torqued to the specified values. Safety notices warn of hazards from high pressure fuel and ensure cleanliness to prevent contamination of fuel system components.
Caterpillar cat 345 c excavator (prefix spc) service repair manual (spc00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It begins with disassembly steps including removing the head, pins, plates, seals, brake piston, separator plates, disks, and rotating group components. Assembly steps are then listed in reverse order and include installing seals, spacers, piston assemblies, springs and other components back into the travel motor housing. Precautions are given such as cleaning parts and applying lubricant before assembly.
Caterpillar cat 345 c hcr material handler excavator (prefix mte) service rep...f8isoeidkdk
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. It outlines:
1) The required tools and removal procedure for the rear gear group which involves removing bolts, seals, gears, bushings and bearings.
2) The installation procedure for the rear gear group which specifies cleaning, applying lubricant and torque specifications for installing the components in reverse order of removal.
3) The removal procedure for the flywheel which requires attaching lifting equipment and removing bolts and ring gear.
4) The installation procedure for the flywheel which involves heating components, applying threadlocker and torque specifications.
Caterpillar cat 345 b track type excavator (prefix 5ws) service repair manual...f8isoeidkdk
The document provides instructions for removing and installing cylinder head components on a Caterpillar 3176C engine, including:
1) Removal steps such as removing sensors, tubes, bolts and the cylinder head using a lifting device.
2) Installation steps such as cleaning surfaces, installing new gaskets and O-rings, lifting the cylinder head into place using a device, and torquing bolts to the specified value.
3) References other documents for removing related parts like the valve mechanism cover beforehand.
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent contamination.
Caterpillar cat 345 b track type excavator (prefix 3mw) service repair manual...f8isoeidkdk
This document provides instructions for disassembling and assembling the travel motor on 345B and 345B L excavator models. It lists the required tools and gives 32 detailed steps for disassembly, including removing covers, springs, pistons, discs, plates, seals, and housing components. The assembly instructions are provided in reverse order and emphasize keeping parts clean to prevent contaminating the hydraulic system.
Caterpillar cat 345 b track type excavator (prefix 2zw) service repair manual...f8isoeidkdk
The document provides instructions for assembling a travel motor. It lists the required tools and gives 30 steps to disassemble parts such as the brake assembly, barrel assembly, swashplate assembly, and shaft assembly. It provides illustrations and notes to inspect parts, replace seals and O-rings, apply lubricant, and ensure cleanliness to prevent contamination. Proper assembly is emphasized to avoid damage and allow for accurate diagnosis if future failures occur.
Caterpillar cat 345 b series ii excavator (prefix alb) service repair manual ...f8isoeidkdk
This document provides instructions for disassembling and assembling the travel motor of a 345B II Excavator. It outlines 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pistons, and housing. It then outlines 29 steps to reassemble the travel motor in reverse order, making sure to clean parts and apply new seals and lubricants. Proper tooling and torque specifications are listed to correctly disassemble and reassemble the travel motor.
Caterpillar cat 335 f lcr excavator (prefix kne) service repair manual (kne00...f8isoeidkdk
This document provides instructions for removing the cylinder head from a Caterpillar C7.1 engine. It involves the following steps:
1. Draining coolant and disconnecting hoses and wiring harnesses from sensors
2. Removing brackets and tubes attached to the cylinder head
3. Gradually loosening the bolts holding the cylinder head in reverse numerical order
4. Removing the bolts and lifting the cylinder head off using a lifting device
The purpose is to remove the cylinder head from the engine for maintenance or repair while taking precautions to contain fluids and correctly support the heavy cylinder head.
Caterpillar cat 345 b excavator (prefix 4ss) service repair manual (4ss00001 ...f8isoeidkdk
This document provides instructions for disassembling and assembling the travel motor on 345B and 345B L Excavator models. It lists required tools and safety notices, then provides 32 detailed steps for disassembly, including removing components like the brake assembly, barrel assembly, and swashplate assembly. It concludes with 14 steps for reassembling components like the shaft assembly, swashplate assembly, and installing bearings and bushings back into the motor housing. Care is advised to keep parts clean and in their original locations during disassembly and reassembly.
Caterpillar cat 345 c l excavator (prefix s5m) service repair manual (s5m0000...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly procedure involves removing over 20 components of the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs to clean all parts, apply anti-seize compound, install bearing cups and cones, and adjust the bearing preload using shims to achieve the proper load. Precise positioning of identification marks is required to reinstall parts in their original locations.
Caterpillar cat 345 c hcr material handler excavator (prefix mte) service rep...jfdskekdmme
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. The removal procedure involves removing bolts and seals to access the rear gear components. Tools are required to remove bearings from assemblies. The installation procedure specifies cleaning parts and applying threadlock before installing components in the reverse order of removal, ensuring proper bearing alignment and torque specifications are followed.
Caterpillar cat 345 b l series ii excavator (prefix akx) service repair manua...jfdskekdmme
This document provides disassembly and assembly instructions for the travel motor on Caterpillar 345B and 345B L Series II Excavators. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pistons, and housing. It also provides lubrication and installation instructions for assembling the travel motor. Proper assembly requires using the correct tools and ensuring parts are clean before reinstalling them in their original locations and orientations.
Caterpillar cat 349 f excavator (prefix tew) service repair manual (tew00001 ...fjsjjekdkme
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavators.
2. It describes removing over 30 components of the travel motor in sequential order, including plugs, springs, pistons, plates, seals, and more.
3. Precautions are provided to protect against spring forces and ensure components are reinstalled in their original positions and order.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 336 e hvg excavator (prefix rbs) service repair manual (rbs00...f8isoeidkdk
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
Caterpillar cat 345 b l excavator (prefix bfg) service repair manual (bfg0000...jfdskekdmme
This document provides instructions for disassembling and assembling the travel motor on 345B excavator models. It lists required tools and parts. The procedure involves 32 steps for disassembly, including removing the brake assembly, barrel assembly, and swashplate assembly. Assembly is the reverse of disassembly with notes to clean parts and apply lubricant before reinstalling. Safety notices are provided to contain fluids and prevent contamination.
Caterpillar cat 345 b l series ii excavator (prefix ags) service repair manua...jfdskekdmme
The document provides step-by-step instructions for disassembling and assembling the final drive components of an excavator. It describes removing components like the travel motor, final drive, carrier assemblies, ring gear, and more. It then describes assembling the components in reverse order, including pressing in bearing cups, installing bearing cones with the proper preload using shims, and reinstalling components like the sprocket housing and coupling gear. Precise tools and lifting devices are required to handle the heavy components.
Caterpillar cat 345 b excavator (prefix amj) service repair manual (amj00001 ...fjsekdmmeed
This document provides assembly instructions for installing a travel motor on a 345B Excavator. It outlines 33 steps to assemble parts like seals, pistons, plates, and shafts inside the travel motor housing. It then describes 4 steps to install the assembled travel motor onto the final drive, including cleaning surfaces, replacing an O-ring seal, and using lifting tools to maneuver the motor into position. Proper torque specifications are given for tightening fasteners.
Caterpillar cat 345 c l excavator (prefix scn) service repair manual (scn0000...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly process involves removing over 20 individual parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly section outlines installing new seals, pressing in bearing cups, adjusting shims to set proper bearing preload, and reinstalling all parts in reverse order. Precise positioning of stamped identification marks on gears is required for correct reassembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...cdsaas
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly process reverses the disassembly steps and includes applying sealant and pressing components together using various tools.
Caterpillar cat 345 c hydraulic excavator (prefix tdg) service repair manual ...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 13 steps for assembly, replacing components in reverse order and noting to clean all parts, apply lubricant, and measure clearances during assembly to ensure proper operation. Tools required are listed for both disassembly and assembly.
Caterpillar cat 340 f excavator (prefix rbd) service repair manual (rbd00001 ...fjsekdmmeed
This document provides instructions for removing and installing the fuel manifold (rail) on a C9.3 engine. The removal procedure involves disconnecting harness assemblies, tube assemblies, and removing bolts to access the fuel manifold. Sensors, solenoid valves, and other components are then removed from the manifold. Installation is the reverse of removal, with all components torqued to the specified values. Safety notices warn of hazards from high pressure fuel and ensure cleanliness to prevent contamination of fuel system components.
Caterpillar cat 345 c excavator (prefix spc) service repair manual (spc00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It begins with disassembly steps including removing the head, pins, plates, seals, brake piston, separator plates, disks, and rotating group components. Assembly steps are then listed in reverse order and include installing seals, spacers, piston assemblies, springs and other components back into the travel motor housing. Precautions are given such as cleaning parts and applying lubricant before assembly.
Caterpillar cat 345 c hcr material handler excavator (prefix mte) service rep...f8isoeidkdk
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. It outlines:
1) The required tools and removal procedure for the rear gear group which involves removing bolts, seals, gears, bushings and bearings.
2) The installation procedure for the rear gear group which specifies cleaning, applying lubricant and torque specifications for installing the components in reverse order of removal.
3) The removal procedure for the flywheel which requires attaching lifting equipment and removing bolts and ring gear.
4) The installation procedure for the flywheel which involves heating components, applying threadlocker and torque specifications.
Caterpillar cat 345 b track type excavator (prefix 5ws) service repair manual...f8isoeidkdk
The document provides instructions for removing and installing cylinder head components on a Caterpillar 3176C engine, including:
1) Removal steps such as removing sensors, tubes, bolts and the cylinder head using a lifting device.
2) Installation steps such as cleaning surfaces, installing new gaskets and O-rings, lifting the cylinder head into place using a device, and torquing bolts to the specified value.
3) References other documents for removing related parts like the valve mechanism cover beforehand.
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent contamination.
Caterpillar cat 345 b track type excavator (prefix 3mw) service repair manual...f8isoeidkdk
This document provides instructions for disassembling and assembling the travel motor on 345B and 345B L excavator models. It lists the required tools and gives 32 detailed steps for disassembly, including removing covers, springs, pistons, discs, plates, seals, and housing components. The assembly instructions are provided in reverse order and emphasize keeping parts clean to prevent contaminating the hydraulic system.
Caterpillar cat 345 b track type excavator (prefix 2zw) service repair manual...f8isoeidkdk
The document provides instructions for assembling a travel motor. It lists the required tools and gives 30 steps to disassemble parts such as the brake assembly, barrel assembly, swashplate assembly, and shaft assembly. It provides illustrations and notes to inspect parts, replace seals and O-rings, apply lubricant, and ensure cleanliness to prevent contamination. Proper assembly is emphasized to avoid damage and allow for accurate diagnosis if future failures occur.
Caterpillar cat 345 b series ii excavator (prefix alb) service repair manual ...f8isoeidkdk
This document provides instructions for disassembling and assembling the travel motor of a 345B II Excavator. It outlines 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pistons, and housing. It then outlines 29 steps to reassemble the travel motor in reverse order, making sure to clean parts and apply new seals and lubricants. Proper tooling and torque specifications are listed to correctly disassemble and reassemble the travel motor.
Caterpillar cat 345 b series ii excavator (prefix akx) service repair manual ...f8isoeidkdk
The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 345B and 345B L Series II. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 27 steps for assembly, replacing components in the reverse order and ensuring proper installation of seals, washers, and other parts. Tools required are listed, as well as lubrication and cleaning notes to prevent contamination.
Caterpillar cat 345 b series ii excavator (prefix akj) service repair manual ...f8isoeidkdk
The document provides instructions for removing and installing connecting rod bearings and crankshaft main bearings on a 345B II excavator. The removal process includes using a bearing tool to remove upper halves of bearings. Installation requires applying clean oil, ensuring tabs engage properly, and torquing bolts to specified values. Crankshaft removal involves taking off bearing caps, thrust bearings and lower bearing halves before lifting the crankshaft out.
Caterpillar cat 345 b series ii excavator (prefix ags) service repair manual ...f8isoeidkdk
This document provides instructions for disassembling and assembling the final drive components of an excavator. It describes removing over 30 individual parts in 21 steps, including the travel motor, final drive, various gears, carriers, shafts, seals and housings. Special tools are required and parts must be reinstalled in their original locations and orientations. The document aims to completely disassemble then reassemble the final drive system.
Caterpillar cat 345 b lc excavator (prefix bfg) service repair manual (bfg000...f8isoeidkdk
The document provides instructions for disassembling and assembling the travel motor on a 345B Excavator model. It lists required tools and parts and gives step-by-step instructions to remove components like the brake cover, brake assembly, springs, seals, gears, and housing parts. Special safety precautions are outlined and components must be cleaned, marked, and reinstalled in their original locations. Detailed illustrations accompany each step.
Caterpillar cat 345 b lc excavator (prefix 7ks) service repair manual (7ks000...f8isoeidkdk
The document provides instructions for disassembling and assembling the travel motor of a 345B L excavator. It lists 32 steps for disassembly, including removing covers, springs, seals, gears, and housing components. Reassembly requires installing these parts in reverse order, taking care to align markings and ensure cleanliness to prevent contaminating the hydraulic system. Proper tools are required and safety precautions must be followed when handling springs and heavy components.
Caterpillar cat 345 b l track type excavator (prefix 3mw) service repair manu...f8isoeidkdk
1. The document provides step-by-step instructions for disassembling and assembling components of a travel motor, including the brake assembly, head assembly, barrel assembly, swashplate assembly, and shaft assembly.
2. Safety precautions are outlined, such as marking parts for reinstallation, cleaning components, and using new seals and O-rings.
3. Tools required are listed, and notes provide information on failure analysis, inspection of parts, and lubrication of components during assembly.
Caterpillar cat 345 b l track type excavator (prefix 2zw) service repair manu...f8isoeidkdk
The document provides instructions for assembling a travel motor. It lists the required tools and gives 30 steps to disassemble parts such as the brake assembly, barrel assembly, swashplate assembly, and shaft assembly. It provides illustrations and notes to inspect parts, replace seals and O-rings, apply lubricant, and ensure cleanliness to prevent contamination. Proper assembly is emphasized to avoid damage and allow for accurate diagnosis if future failures occur.
Caterpillar cat 345 b l series ii excavator (prefix alb) service repair manua...f8isoeidkdk
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and pins. Technicians are advised to clean all parts thoroughly, replace all O-rings and seals, and ensure components are reinstalled in their original locations and orientations. Proper assembly helps prevent contamination and failures.
Caterpillar cat 345 b l series ii excavator (prefix akx) service repair manua...f8isoeidkdk
The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 345B and 345B L Series II. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 27 steps for assembly, replacing components in the reverse order and ensuring proper installation of seals, washers, and other parts. Tools required are listed, as well as lubrication and cleaning notes to prevent contamination.
Caterpillar cat 345 b l series ii excavator (prefix akj) service repair manua...f8isoeidkdk
The document provides instructions for removing and installing connecting rod bearings and crankshaft main bearings on a 345B II excavator. The removal process includes using a bearing tool to remove upper halves of bearings. Installation requires applying clean oil, ensuring tabs engage properly, and torquing bolts to specified values. Crankshaft removal involves taking off bearing caps, thrust bearings and lower bearing halves before lifting the crankshaft out.
Caterpillar cat 345 b l series ii excavator (prefix ags) service repair manua...f8isoeidkdk
This document provides instructions for disassembling and assembling the final drive components of an excavator. It describes removing over 30 individual parts in 21 steps, including the travel motor, final drive, various gears, carriers, shafts, seals and housings. Special tools are required and parts must be reinstalled in their original locations and orientations. The document aims to completely disassemble then reassemble the final drive system.
Caterpillar cat 345 b l excavator (prefix 9gs) service repair manual (9gs0000...f8isoeidkdk
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar cat 345 b l excavator (prefix 7ks) service repair manual (7ks0000...f8isoeidkdk
The document provides instructions for disassembling and assembling the travel motor of a 345B L excavator. It lists 32 steps for disassembly, including removing covers, springs, seals, gears, and housing components. For assembly, it specifies cleaning parts and ensuring components are reinstalled in their original locations with proper lubrication to avoid damage. Proper containment of fluids is emphasized during maintenance.
Caterpillar cat 345 b l excavator (prefix 4ss) service repair manual (4ss0000...f8isoeidkdk
This document provides instructions for disassembling and assembling the travel motor on Caterpillar 345B and 345B L Excavator models. It lists required tools and parts, and provides 32 numbered steps describing how to remove components like the brake assembly, piston, gears, and housing. Safety notices are included to handle fluids properly and avoid damage when reassembling parts.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Required Tools
Tool Part Number Part Description Qty
(A) 1P-2420 Transmission Repair Stand 1
(B) 1P-1859 Pliers 1
(C) 1P-1863 Pliers 1
(D) 138-7575 Link Bracket 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Failure to properly assemble parts or failure to follow established
procedures can lead to damage to the parts and assembly.
To avoid damage to parts, always identify and mark the parts so that
they can be installed into the same location. Never force parts during
assembly. Keep parts clean and lubricated.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
2/14
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline for Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
Illustration 1 g00633207
1. Thoroughly clean the outside of the travel motor prior to disassembly. Fasten travel motor
(1) to Tool (A). The weight of the travel motor is 125 kg (275 lb).
2. Put an alignment mark across all housings of the travel motor for assembly purposes.
3. Disconnect tube assembly (2) .
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
3/14
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00633208
Illustration 3 g00633209
4. Remove two socket head bolts (3) from the brake cover that are 180 degrees from each
other. Replace these two bolts with bolts that are slightly longer in length. The two longer
bolts will retain the brake cover when the remaining socket head bolts (3) are removed.
5. Evenly remove the remaining socket head bolts (3) that hold the brake cover in position.
Remove the two longer bolts (3). Remove brake cover (4) from the brake assembly.
4/14
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g00633210
6. If necessary, remove brake adjusting screws (5) from the brake cover.
Illustration 5 g00633212
7. Remove brake assembly (6) from the head assembly.
Illustration 6 g00633213
Note: There is an inner spring and an outer spring in each spring set.
8. Remove spring sets (7) from the brake piston.
5/14
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g00633214
9. Turn the brake housing to the other side. Remove O-ring seal (8) .
Illustration 8 g00633216
10. Use two suitable forcing screws (9) in order to remove brake piston (10) from the brake
housing.
Illustration 9 g00633217
6/14
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 11. Remove discs (11) and plates (12) .
Illustration 10 g00633218
12. Remove O-ring seal (13) .
13. Use Tool (B) in order to remove retaining ring (14). Remove gear (15) .
Illustration 11 g00633219
14. Use Tool (C) in order to remove retaining ring (16) .
15. Remove the nut and bushing (17) from the rod assembly.
16. Remove four socket head bolts (18) that hold the head assembly to the motor housing.
7/14
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g00633220
17. Fasten Tool (D) and a hoist to head assembly (19), as shown. Carefully remove the head
assembly from the motor housing. The weight of the head assembly is 25 kg (55 lb).
Illustration 13 g00633221
18. Remove thrust plate (20) from the head.
Illustration 14 g00633223
8/14
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 19. Remove O-ring seal (22) from the head.
20. Remove bearing (23) from the head.
21. Remove pin (21) from the head.
Illustration 15 g00633224
22. Remove O-ring seal (25) from the motor housing.
23. Turn the motor housing on the side, as shown.
Note: Keep the components together, while you remove the barrel assembly from the motor
housing. All parts in the barrel assembly must be reinstalled in the original locations.
24. Carefully remove barrel assembly (24) from the motor housing so the components do not
come apart.
25. Disassemble barrel assembly (24), as follows:
Illustration 16 g00633225
a. Place identification marks on piston assemblies (27), retainer (26), and barrel (28).
Remove piston assemblies (27), and retainer (26) from barrel (28) .
9/14
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. b. Separate piston assemblies (27) from retainer (26) .
Illustration 17 g00633227
c. Remove guide (29) from the barrel.
Illustration 18 g00633228
Note: Take note of the shims (30) that are positioned on the barrel for installation
purposes.
d. Remove shims (30) from the barrel.
10/14
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY ...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g00633230
26. Remove adjusting screw (31) from the motor housing. Remove the O-ring seal from the
adjusting screw.
27. Remove swashplate assembly (32) from the motor housing.
28. Disassemble the swashplate assembly, as follows:
Illustration 20 g00633231
a. Remove plate (33) .
11/14
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY ...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 21 g00633232
b. Remove three pins (34) from the plate.
c. Remove two screws (35) .
d. Remove plate (36) .
e. Remove two plungers (37) .
Illustration 22 g00633235
29. Use Tool (B) in order to remove retaining ring (38) that holds shaft assembly (39) in the
motor housing.
Illustration 23 g00633238
30. Use a soft faced hammer in order to remove shaft assembly (39) from the motor housing in
the direction that is shown.
31. Disassemble shaft assembly (39), as follows:
12/14
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY ...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 24 g00633239
a. Remove O-ring seal (40) from cover (41) .
b. Remove cover (41) from the shaft.
Illustration 25 g00633241
c. Remove lip seal (42) from cover (41) .
Illustration 26 g00633243
13/14
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY ...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. d. Use Tool (C) in order to remove retaining ring (43) that holds bearing (44) in position
on the shaft.
Illustration 27 g00633245
e. Put the shaft in a press, as shown. Press the shaft out of bearing (44) .
Illustration 28 g00633246
32. Remove two screws (47) and two bearings (46) from the motor housing. Remove two
bushings (45) from the motor housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 27 17:23:34 UTC+0800 2020
14/14
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY ...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B EXCAVATOR BFG
Configuration: 345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
345B, 345B Series II and W345B Series II Excavators Machine Systems
Media Number -SENR1934-11 Publication Date -01/01/2012 Date Updated -12/01/2012
i03721001
Travel Motor - Assemble - Series I
SMCS - 4351-016
S/N - 2NW1-UP
S/N - 2SW1-UP
S/N - 2ZW1-UP
S/N - 3MW1-UP
S/N - 4SS1-UP
S/N - 5WS1-UP
S/N - 6MW1-UP
S/N - 6XS1-UP
S/N - 7KS1-UP
S/N - 8KW1-UP
S/N - 8RW1-UP
S/N - 9CW1-UP
S/N - 9GS1-UP
S/N - BFG1-UP
Installation Procedure
Table 1
1/15
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Required Tools
Tool Part Number Part Description Qty
(A) 1P-2420 Transmission Repair Stand 1
(B) 1P-1859 Pliers 1
(C) 1P-1863 Pliers 1
(D) 138-7575 Link Bracket 2
(E) 1P-0520 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline For Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound during the
assembly procedure.
Note: Apply a light film of "10W" oil to all components before assembly.
2/15
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g00633246
1. Use Tool (E) in order to install two bushings (45) in the motor housing. Install the bushings
until the bushings are seated in the motor housing.
2. Put two bearings (46) in position in the motor housing, as shown.
3. Put 9S-3263 Thread Lock Compound on the threads of two screws (47) .
4. Install the two screws, and tighten the screws to a torque of 5 N·m (44 lb in).
5. Assemble shaft assembly (39) , as follows:
Illustration 2 g00633243
a. Heat bearing (44) . Install the bearing until the bearing makes contact with the
shoulder on the shaft.
b. Use Tool (C) in order to install retaining ring (43) .
3/15
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 3 g00633241
c. Use Tool (E) in order to install lip seal (42) in cover (41) .
d. Install the seal until the seal makes contact with the counterbore in the cover and with
the sealing lip facing toward the inside. Lubricate the lip of the seal with clean
hydraulic oil.
Illustration 4 g00633239
e. Install cover (41) on the shaft, as shown.
f. Install O-ring seal (40) on the cover. Lubricate the O-ring seal with clean hydraulic
oil.
4/15
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 5 g00633235
6. Use a soft faced hammer in order to install shaft assembly (39) in the motor housing. Make
sure that the shaft assembly is seated in the motor housing.
7. Use Tool (B) in order to install retaining ring (38) in the motor housing.
8. Assemble the swashplate assembly, as follows:
Illustration 6 g00633232
a. Install two plungers (37) .
b. Install plate (36) .
c. Install two screws (35) .
d. Install three pins (34) in the plate.
5/15
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 7 g00633231
e. Install plate (33) .
Illustration 8 g00633230
9. Install swashplate assembly (32) in the motor housing, as shown.
10. Install the O-ring seal on adjusting screw (31) . Install the screw for adjusting in the motor
housing.
11. Assemble barrel assembly (24) , as follows:
6/15
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 9 g00633228
a. Install the original amount of shims (30) on the barrel. Make sure that the shims are
installed in the original positions.
Illustration 10 g00633227
b. Install guide (29) on the barrel, as shown. Make sure that the guide is seated squarely.
Illustration 11 g00633225
c. Install nine piston assemblies (27) in the original location in retainer (26) .
d. Install the piston assemblies with the retainer in the original location in the barrel.
7/15
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 12 g00633227
Note: Make sure that the barrel assembly (24) does not fall apart during installation in the
motor housing.
Illustration 13 g02005414
12. Carefully install barrel assembly (24) over the shaft in the motor housing. Make sure that
the components of the barrel assembly do not fall apart during installation. Install lip type
seal (25A) .
13. Install O-ring seal (25) in the motor housing.
8/15
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 14 g00633223
14. Install pin (21) in the head.
15. Install bearing (23) in the head. Make sure that the bearing makes contact with the
counterbore in the head during installation.
16. Install O-ring seal (22) in the head.
Illustration 15 g00633221
17. Install thrust plate (20) on the head, as shown.
9/15
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY 31...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 16 g00633220
18. Fasten Tool (D) and a hoist to head assembly (19) , as shown. Carefully put the head
assembly in the original position on the motor housing.
Illustration 17 g00633219
19. Put 9S-3263 Thread Lock Compound on the threads of four socket head bolts (18) .
20. Install four socket head bolts (18) that hold the head assembly to the motor housing.
21. Put 9S-3263 Thread Lock Compound on the threads of bushing (17) .
22. Install the bushing and the nut on the rod assembly in the motor housing.
23. Use Tool (C) in order to install retaining ring (16) on the shaft.
10/15
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY ...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 18 g00633416
24. Put gear (15) in position on the shaft. Use Tool (B) in order to install retaining ring (14) .
This will hold the gear in position.
25. Install O-ring seal (13) in the head assembly.
Illustration 19 g00633421
26. Install discs (11) and plates (12) in alternating order. Start with a disc and end with a disc.
11/15
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY ...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 20 g00633417
27. Install brake piston (10) in the brake housing.
Illustration 21 g00633214
28. Turn the brake housing on the other side. Install O-ring seal (8) in the brake housing.
Illustration 22 g00633423
Note: There is an inner spring and an outer spring in each spring set.
29. Install spring sets (7) in the brake piston.
12/15
345B, 345B L & 345B LC Excavator BFG00001-UP (MACHINE) POWERED BY ...
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...