The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C9.3 engine. It describes:
1) Removing the flywheel first before removing the flywheel housing.
2) Using lifting brackets and bolts to remove the flywheel housing from the engine block.
3) Applying gasket maker to the mounting surface before reinstalling the flywheel housing.
4) Reinstalling the flywheel housing with lifting brackets and bolts, and then reinstalling the flywheel.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...zatao0179249295
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C9.3 engine. It describes:
1) Removing the flywheel first before removing the flywheel housing.
2) Attaching lifting devices to the flywheel housing and removing bolts to take it off the engine block.
3) Applying gasket material before reinstalling the flywheel housing and tightening the bolts in reverse order of removal.
The document provides instructions for installing and removing components related to the rear power take-off (RPTO) system on a Caterpillar C9.3 engine. The removal procedure includes removing the crankshaft rear seal, various bolts and gears, thrust washers, dowels, bearings, seals and the PTO shaft. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order, applying thread locking compound to bolts, and torquing bolts to the specified values.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...luanxianshi27
The document provides instructions for installing and removing components related to the rear power take-off (RPTO) system on a Caterpillar C9.3 engine. The removal procedure includes removing the crankshaft rear seal, various bolts and gears, thrust washers, dowels, bearings, seals and the PTO shaft. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order, applying thread locking compound to bolts, and torquing bolts to the specified values.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...cnp692569
The document provides instructions for installing and removing components related to the rear power take-off (RPTO) system on a Caterpillar C9.3 engine. The removal procedure includes removing the crankshaft rear seal, various bolts and gears, thrust washers, dowels, bearings, seals and the PTO shaft. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order, applying thread lock to bolts and torquing to specification.
The document provides instructions for installing and removing components related to the rear power take-off (RPTO) system on a Caterpillar C9.3 engine. The removal procedure includes removing the crankshaft rear seal, various bolts and gears, thrust washers, dowels, bearings, seals and the PTO shaft. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order, applying thread locking compound to bolts, and torquing bolts to the specified values.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...shudun96087
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the flywheel, muffler brackets, and bolts to remove the housing. For installation, it describes lifting the housing back into place with a lifting device, reinstalling the bolts, and reattaching the muffler brackets. Precautions are provided to keep parts clean and contain fluids during the process.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...qme229722
This service repair manual provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar C6.4 engine. The flywheel is removed using lifting tools and bolts, while the flywheel housing is removed by first removing the electric starter motor, flywheel, and bolts. Gaskets and seals are also replaced during removal and installation of components. Tools required include link brackets, driver groups, and slide hammers.
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C9.3 engine. It describes:
1) Removing the flywheel first before removing the flywheel housing.
2) Using lifting brackets and bolts to remove the flywheel housing from the engine block.
3) Applying gasket maker to the mounting surface before reinstalling the flywheel housing.
4) Reinstalling the flywheel housing with lifting brackets and bolts, and then reinstalling the flywheel.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...zatao0179249295
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C9.3 engine. It describes:
1) Removing the flywheel first before removing the flywheel housing.
2) Attaching lifting devices to the flywheel housing and removing bolts to take it off the engine block.
3) Applying gasket material before reinstalling the flywheel housing and tightening the bolts in reverse order of removal.
The document provides instructions for installing and removing components related to the rear power take-off (RPTO) system on a Caterpillar C9.3 engine. The removal procedure includes removing the crankshaft rear seal, various bolts and gears, thrust washers, dowels, bearings, seals and the PTO shaft. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order, applying thread locking compound to bolts, and torquing bolts to the specified values.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...luanxianshi27
The document provides instructions for installing and removing components related to the rear power take-off (RPTO) system on a Caterpillar C9.3 engine. The removal procedure includes removing the crankshaft rear seal, various bolts and gears, thrust washers, dowels, bearings, seals and the PTO shaft. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order, applying thread locking compound to bolts, and torquing bolts to the specified values.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...cnp692569
The document provides instructions for installing and removing components related to the rear power take-off (RPTO) system on a Caterpillar C9.3 engine. The removal procedure includes removing the crankshaft rear seal, various bolts and gears, thrust washers, dowels, bearings, seals and the PTO shaft. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order, applying thread lock to bolts and torquing to specification.
The document provides instructions for installing and removing components related to the rear power take-off (RPTO) system on a Caterpillar C9.3 engine. The removal procedure includes removing the crankshaft rear seal, various bolts and gears, thrust washers, dowels, bearings, seals and the PTO shaft. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order, applying thread locking compound to bolts, and torquing bolts to the specified values.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...shudun96087
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the flywheel, muffler brackets, and bolts to remove the housing. For installation, it describes lifting the housing back into place with a lifting device, reinstalling the bolts, and reattaching the muffler brackets. Precautions are provided to keep parts clean and contain fluids during the process.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...qme229722
This service repair manual provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar C6.4 engine. The flywheel is removed using lifting tools and bolts, while the flywheel housing is removed by first removing the electric starter motor, flywheel, and bolts. Gaskets and seals are also replaced during removal and installation of components. Tools required include link brackets, driver groups, and slide hammers.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...kesi7153062
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the flywheel, muffler brackets, and bolts to remove the housing. For installation, it describes lifting the housing back into place with a lifting device, reinstalling the bolts, and reattaching the muffler brackets. Precautions are provided to keep parts clean and contain fluids during the process.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket with guide studs, and installing the front cover with bolts finger tight.
4. Aligning the front cover with an alignment tool and tightening the bolts to specification. Installing a new front seal completes the process.
The document provides instructions for removing and installing a crankshaft front seal and front cover on a Caterpillar 330F excavator engine. The removal process involves using specialty tools to screw the front seal out of the front cover. For installation, a new seal is lubricated and installed using an installer tool. Instructions also cover removing and installing the front cover, which requires identifying bolt lengths and using guide studs and an alignment tool.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket and front cover with guide studs, and tightening bolts with an alignment tool installed.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket with guide studs, and installing the front cover with alignment tools. Reinstalling the front seal, pulley, and fan completes the process.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket with guide studs, and installing the front cover with alignment tools. Reinstalling the front seal, pulley, and fan completes the process.
The document provides instructions for removing and installing a crankshaft front seal and front cover on a Caterpillar 330F excavator engine. The removal process involves using specialty tools to screw the front seal out of the front cover. For installation, a new seal is lubricated and installed using an installer tool. Instructions also cover removing and installing the front cover, which requires identifying bolt lengths and using guide studs and an alignment tool.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are listed for removing the oil seal from the housing. Installation includes checking dowels, installing a new gasket and oil seal, and securing the housing with bolts. End steps include installing the flywheel and starting motor.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual Instant D...zan2736ban
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes:
1. Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2. Using a link bracket and driver group to remove the flywheel housing bolts.
3. Reversing the removal steps to install the flywheel housing, ensuring all components are clean prior to installation.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...fusjekkdmdmd2w
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes:
1. Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2. Using a link bracket and driver group to remove the flywheel housing bolts.
3. Reversing the removal steps to install the flywheel housing, ensuring all components are clean prior to installation.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...f8uesjdkdmdm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are listed to lift the housing off and remove the oil seal. Reinstallation involves cleaning surfaces, installing a new gasket and oil seal, and securing the housing with bolts. End steps include installing the flywheel and starting motor.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...8ufjsekddm8u
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are required to lift the housing and remove the oil seal. When installing, a new gasket and oil seal are used and the housing is bolted back in place before reinstalling the flywheel and starting motor.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are required to lift the housing and remove the oil seal. When installing, a new gasket and oil seal are used and the housing is bolted back in place before reinstalling the flywheel and starting motor.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...ufjksemd8ujd
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are listed for removing the oil seal from the housing. Installation includes checking dowels, installing a new gasket and oil seal, and securing the housing with bolts. End steps include installing the flywheel and starting motor.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...km7seydwuhdw
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are listed for removing the oil seal from the housing. Installation includes checking dowels, installing a new gasket and oil seal, and securing the housing with bolts. End steps include installing the flywheel and starting motor.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are listed to lift the housing off and remove the oil seal. Reinstallation involves cleaning surfaces, installing a new gasket and oil seal, and securing the housing with bolts. End steps include installing the flywheel and starting motor.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...jdkskmdmdm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes:
1. Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2. Using a link bracket and driver group to remove the flywheel housing bolts.
3. Reversing the removal steps to install the flywheel housing, ensuring all components are clean prior to installation.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...prmy389342
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are listed for removing the oil seal from the housing. Installation includes checking dowels, installing a new gasket and oil seal, and securing the housing with bolts. End steps include installing the flywheel and starting motor.
Caterpillar cat 323 d l excavator (prefix l5z) service repair manual (l5z0000...fjjsekmsmmes
The document provides instructions for removing and installing a flywheel, flywheel housing, and crankshaft rear seal on a Caterpillar C6.4 engine. The flywheel is removed using lifting tools and bolts, while the flywheel housing requires removing mounting bolts and seals. The crankshaft rear seal is removed using a slide hammer and distorter, and the new seal is installed using a locator, installer, and compound.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B4N) Service Repair Manual Instant ...yan77xunhao
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the cylinder head, applying anti-seize compound to bolts, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other components like the rocker arm first, ensuring timing marks are aligned, and lubricating the camshaft lobes during installation.
- Removing and installing the camshaft gear by pressing it off the camshaft, aligning the keyway, and heating the gear to the proper temperature during installation.
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
CASE CX700 CRAWLER EXCAVATOR Service Repair Manual Instant Download.pdfyan77xunhao
CASE/AKCELA hydraulic fluid is recommended for use in the hydraulic system. The specific fluid to use depends on the ambient temperature range. For temperate climates from -20°C to +40°C, use CASE/AKCELA HYDRAULIC EXCAVATOR FLUID. For hot climates from 0°C to +50°C, use CASE/AKCELA AW HYDRAULIC FLUID 68 HV.
More Related Content
Similar to Caterpillar Cat 336E and 336E L HVG Excavator (Prefix RBS) Service Repair Manual Instant Download.pdf
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...kesi7153062
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the flywheel, muffler brackets, and bolts to remove the housing. For installation, it describes lifting the housing back into place with a lifting device, reinstalling the bolts, and reattaching the muffler brackets. Precautions are provided to keep parts clean and contain fluids during the process.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket with guide studs, and installing the front cover with bolts finger tight.
4. Aligning the front cover with an alignment tool and tightening the bolts to specification. Installing a new front seal completes the process.
The document provides instructions for removing and installing a crankshaft front seal and front cover on a Caterpillar 330F excavator engine. The removal process involves using specialty tools to screw the front seal out of the front cover. For installation, a new seal is lubricated and installed using an installer tool. Instructions also cover removing and installing the front cover, which requires identifying bolt lengths and using guide studs and an alignment tool.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket and front cover with guide studs, and tightening bolts with an alignment tool installed.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket with guide studs, and installing the front cover with alignment tools. Reinstalling the front seal, pulley, and fan completes the process.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket with guide studs, and installing the front cover with alignment tools. Reinstalling the front seal, pulley, and fan completes the process.
The document provides instructions for removing and installing a crankshaft front seal and front cover on a Caterpillar 330F excavator engine. The removal process involves using specialty tools to screw the front seal out of the front cover. For installation, a new seal is lubricated and installed using an installer tool. Instructions also cover removing and installing the front cover, which requires identifying bolt lengths and using guide studs and an alignment tool.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are listed for removing the oil seal from the housing. Installation includes checking dowels, installing a new gasket and oil seal, and securing the housing with bolts. End steps include installing the flywheel and starting motor.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual Instant D...zan2736ban
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes:
1. Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2. Using a link bracket and driver group to remove the flywheel housing bolts.
3. Reversing the removal steps to install the flywheel housing, ensuring all components are clean prior to installation.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...fusjekkdmdmd2w
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes:
1. Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2. Using a link bracket and driver group to remove the flywheel housing bolts.
3. Reversing the removal steps to install the flywheel housing, ensuring all components are clean prior to installation.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...f8uesjdkdmdm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are listed to lift the housing off and remove the oil seal. Reinstallation involves cleaning surfaces, installing a new gasket and oil seal, and securing the housing with bolts. End steps include installing the flywheel and starting motor.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...8ufjsekddm8u
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are required to lift the housing and remove the oil seal. When installing, a new gasket and oil seal are used and the housing is bolted back in place before reinstalling the flywheel and starting motor.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are required to lift the housing and remove the oil seal. When installing, a new gasket and oil seal are used and the housing is bolted back in place before reinstalling the flywheel and starting motor.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...ufjksemd8ujd
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are listed for removing the oil seal from the housing. Installation includes checking dowels, installing a new gasket and oil seal, and securing the housing with bolts. End steps include installing the flywheel and starting motor.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...km7seydwuhdw
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are listed for removing the oil seal from the housing. Installation includes checking dowels, installing a new gasket and oil seal, and securing the housing with bolts. End steps include installing the flywheel and starting motor.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are listed to lift the housing off and remove the oil seal. Reinstallation involves cleaning surfaces, installing a new gasket and oil seal, and securing the housing with bolts. End steps include installing the flywheel and starting motor.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...jdkskmdmdm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes:
1. Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2. Using a link bracket and driver group to remove the flywheel housing bolts.
3. Reversing the removal steps to install the flywheel housing, ensuring all components are clean prior to installation.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...prmy389342
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are listed for removing the oil seal from the housing. Installation includes checking dowels, installing a new gasket and oil seal, and securing the housing with bolts. End steps include installing the flywheel and starting motor.
Caterpillar cat 323 d l excavator (prefix l5z) service repair manual (l5z0000...fjjsekmsmmes
The document provides instructions for removing and installing a flywheel, flywheel housing, and crankshaft rear seal on a Caterpillar C6.4 engine. The flywheel is removed using lifting tools and bolts, while the flywheel housing requires removing mounting bolts and seals. The crankshaft rear seal is removed using a slide hammer and distorter, and the new seal is installed using a locator, installer, and compound.
Similar to Caterpillar Cat 336E and 336E L HVG Excavator (Prefix RBS) Service Repair Manual Instant Download.pdf (19)
Caterpillar Cat 330C FM EXCAVATOR (Prefix B4N) Service Repair Manual Instant ...yan77xunhao
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the cylinder head, applying anti-seize compound to bolts, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other components like the rocker arm first, ensuring timing marks are aligned, and lubricating the camshaft lobes during installation.
- Removing and installing the camshaft gear by pressing it off the camshaft, aligning the keyway, and heating the gear to the proper temperature during installation.
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
CASE CX700 CRAWLER EXCAVATOR Service Repair Manual Instant Download.pdfyan77xunhao
CASE/AKCELA hydraulic fluid is recommended for use in the hydraulic system. The specific fluid to use depends on the ambient temperature range. For temperate climates from -20°C to +40°C, use CASE/AKCELA HYDRAULIC EXCAVATOR FLUID. For hot climates from 0°C to +50°C, use CASE/AKCELA AW HYDRAULIC FLUID 68 HV.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling major transmission components like gears, shafts, bearings, springs and seals. Proper cleaning and lubrication of parts is emphasized. Safety notes warn of risks from improper handling of spring-loaded components.
The document provides instructions for removing and installing the boom on a 420F Backhoe Loader. It describes:
1) Disconnecting hoses and removing pins/bolts to separate the boom from the loader.
2) Using pullers and lifting devices to remove bearings and the boom cylinder.
3) Reversing the process to install the new or repaired boom by pressing in bearings and reattaching components.
This document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles
- Loosening the threaded nut and removing the nozzle and seat washer from the cylinder block
- Cleaning parts and installing a new seat washer before installing the nozzle
- Carefully tightening the nut to the specified torque
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual I...yan77xunhao
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and using guide bolts to position the cylinder head before reconnecting components.
This document provides instructions for removing the cylinder head from a Caterpillar 3054C engine. The steps include:
1. Draining the coolant and engine oil from the engine oil cooler.
2. Removing the air filter hose.
3. Removing any attached components to the cylinder head like the valve cover, rocker arms, pushrods, etc.
4. Removing the cylinder head bolts and removing the cylinder head.
The document provides instructions for disassembling and assembling components of the control valve for an excavator model 385B. It describes 25 steps to disassemble parts like actuators, manifolds, solenoids, valves, seals and more. The assembly section outlines 14 steps and provides warnings to properly install spring-loaded parts to prevent injury. Precautions are noted to clean parts and check for wear before reassembly.
Caterpillar Cat 385C and 385C L Excavator (Prefix JCM) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Tools, torque specs and notes on lubrication and seals are provided. The goal is to disassemble, clean, inspect for wear, replace worn parts, and reassemble the final drive while maintaining cleanliness.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to assembly.
3) Assembling the components in reverse order, applying lubricants to bearings and sealing surfaces.
4) Using tools and procedures to properly set bearing preload when installing the main housing.
Caterpillar Cat 385B and 385B L Excavator (Prefix FDL) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
Caterpillar Cat 374F L Excavator (Prefix AP4) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, gears, shafts and housings. The assembly process specifies cleaning parts, applying sealant, installing bearings and seals, and adjusting bearing preload using shims. Precautions are given for using hydraulic cylinders and puller studs during the assembly process.
This document provides instructions for disassembling and assembling the governor and fuel injection pump housing of a 3306 vehicular engine. It describes removing over 30 individual parts in 12 steps to disassemble the governor. It then describes assembling the governor in 35 steps, noting to clean and oil all parts before assembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifter group
- Camshaft
- Camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep parts clean and properly support components.
The document provides instructions for removing and disassembling the transmission of a 428D Backhoe Loader. It describes 19 steps to disassemble the transmission into its major components which include removing valve groups, filters, shafts, seals and gaskets. Special tools are required and cleanliness is important when disassembling the transmission.
The document provides instructions for removing the bank valve from a 420E Backhoe Loader. It is a 19 step process that involves draining fluids, removing floor plates, disconnecting hoses and wiring, and using lifting equipment to remove the heavy bank valve unit. The bank valve is then disassembled into its individual valve components for inspection or replacement.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It outlines 20 steps for the installation, which include lowering bearing temperatures, placing bars through frames, installing pins and bolts, connecting hoses and harnesses, and positioning cylinders. Tools required include levers, drivers, and lifting devices. Safety precautions are provided for working on pressurized hydraulic systems.
The document provides instructions to disassemble an axle housing, axle shaft, and wheel flange from a 420E backhoe loader. It outlines 9 steps to remove components including the axle shaft, retaining rings, locking plates, seals, bearings and bushings. Tools required include a spanner wrench, retaining ring pliers, and a combination puller. The purpose is to disassemble these components for repair or replacement.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E HVG MOBILE HYD POWER UNIT RBS
Configuration: 336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Media Number -KENR8149-07 Publication Date -01/05/2014 Date Updated -29/05/2014
i02271627
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Bolt
(M16 x 2 by 4 inch)
1
B 138-7573 Link Bracket 1
C FT-2711 Special Bolt 2
D 9S-3263 Thread Lock Compound 1
1. Raise the temperature of the flywheel ring gear. Do not use a torch to heat the flywheel ring
gear. Install the flywheel ring gear on the flywheel. Position the flywheel ring gear with the
part number toward the crankshaft. Allow the flywheel ring gear to cool. Use a soft hammer
in order to seat the flywheel ring gear against the shoulder of the flywheel.
1/2
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01138041
2. Attach Tooling (B) and a suitable lifting device to flywheel (2). The weight of flywheel (2)
is approximately 40 kg (85 lb).
3. Position flywheel (2) on Tooling (A).
4. Apply Tooling (D) to the threads of bolts (1).
Note: Tooling (C) should be removed at this time, if Tooling (C) was used in the removal
procedure for the flywheel.
5. Install bolts (1). Remove Tooling (A) and install remaining bolt (1). Tighten the bolts
evenly to a torque of 300 ± 40 N·m (221 ± 30 lb ft).
6. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 23:39:14 UTC+0800 2020
2/2
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E HVG MOBILE HYD POWER UNIT RBS
Configuration: 336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Media Number -KENR8149-07 Publication Date -01/05/2014 Date Updated -29/05/2014
i05820902
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
A. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g01140085
1. Remove bolts (2) .
2. Remove crankshaft rear seal (1) from the crankshaft.
Note: Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual Inspection and
Magnetic Particle Inspection" for the correct inspection procedure of the crankshaft seal surface.
Note: Refer to Reuse and Salvage Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9,
C-9, C10, C11, C12, C-12, C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the
correct specifications of the crankshaft.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 23:40:10 UTC+0800 2020
2/2
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E HVG MOBILE HYD POWER UNIT RBS
Configuration: 336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Media Number -KENR8149-07 Publication Date -01/05/2014 Date Updated -29/05/2014
i05857809
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 Primer N -
B - Loctite 620 Retaining Compound -
C 147-2675 Wear Sleeve Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01140085
Illustration 2 g03698745
Numerical tightening sequence for bolts (2).
Note: If required, install a crankshaft wear sleeve at engine overhaul. For more information
please refer to the following Reuse and Salvage Guidelines. Refer to Reuse and Salvage
Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9, C-9, C10, C11, C12, C-12,
2/3
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the correct specifications
of the crankshaft. Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual
Inspection and Magnetic Particle Inspection" for the correct inspection procedure of the
crankshaft seal surface.
1. If a crankshaft wear sleeve is necessary, refer to Step 1.a through Step 1.d to install the
crankshaft wear sleeve. If a crankshaft wear sleeve is not necessary, refer to Step 2.
a. Clean and polish the crankshaft of imperfections.
b. Use Tooling (A) to clean the outside diameter of the crankshaft and the inside
diameter of the crankshaft wear sleeve.
c. Apply Tooling (B) to the outside diameter of the crankshaft and the inside diameter of
the crankshaft wear sleeve.
d. Use Tooling (C) to install the crankshaft wear sleeve.
Note: Leave the shipping sleeve in place to install the crankshaft rear seal. The crankshaft
rear seal must be installed dry.
Note: If the seal group, O-ring seal, and the shipping sleeve are separated, these
components should not be used.
2. Lubricate the O-ring seal with clean engine oil that is on the back of the crankshaft rear seal
(1).
3. Position crankshaft rear seal (1) and the shipping sleeve over the crankshaft. Push
crankshaft rear seal (1) in place. This will dislodge the shipping sleeve.
Note: Do not remove the shipping sleeve until bolts (2) are installed.
4. Install new bolts (2) hand tight. Then, tighten bolts (2) in numerical sequence, shown in
Illustration 2. Tighten bolts (2) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 23:41:06 UTC+0800 2020
3/3
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E HVG MOBILE HYD POWER UNIT RBS
Configuration: 336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Media Number -KENR8149-07 Publication Date -01/05/2014 Date Updated -29/05/2014
i05534615
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
Start By:
a. Remove the flywheel.
1/3
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g01138072
1. Fasten Tooling (A) and a suitable lifting device to flywheel housing (1). The weight of
flywheel housing (1) is approximately 25 kg (55 lb).
2. Remove bolts (2).
3. Remove bolts (3) (not shown) that fasten the engine oil pan to flywheel housing (1).
Remove flywheel housing (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B - LoctiteHigh Flex Form-In-Place Gasket 1
1. Apply Tooling (B) to the entire mounting surface of the flywheel housing prior to
installation.
2/3
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 2 g01138072
2. Fasten Tooling (A) and a suitable lifting device to flywheel housing (1). The weight of
flywheel housing (1) is approximately 25 kg (55 lb). Position flywheel housing (1) on the
engine block.
3. Install bolts (2).
4. Install bolts (3) (not shown) that fasten the engine oil pan to flywheel housing (1).
End By:
a. Install the flywheel.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 23:42:02 UTC+0800 2020
3/3
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E HVG MOBILE HYD POWER UNIT RBS
Configuration: 336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Media Number -KENR8149-07 Publication Date -01/05/2014 Date Updated -29/05/2014
i02355706
Rear Power Take-Off (RPTO) - Remove
SMCS - 1165-011-RE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud (M 12 X 1.75 by 6 inch) 2
B 1P-0520 Driver Group 1
C 156-7100 Puller Group 1
Start By:
A. Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g01103652
1. Install Tooling (A) in the crankshaft through crankshaft gear (17) .
2. Remove bolts (23) , cover (22) , and gasket (21) . Remove crankshaft gear (17) from the
crankshaft. Remove seal (16) .
3. Remove bolts (19) , bolt (20) , idler shaft (18) , and idler gear (14) .
4. Remove bearing (15) from idler gear (14) with Tooling (B) .
5. Remove lip seal (12) , bolts (11) , and adapter assembly (10) . Remove O-ring seal (9) , dowels
(8) , thrust washer (7) , and bearing (6) from adapter assembly (10) .
6. Remove PTO shaft (5) from flywheel housing (4) . Remove dowel (13) .
7. Remove thrust washer (2) and dowels (1) .
2/3
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 8. Remove bearing (3) with Tooling (C) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 23:42:57 UTC+0800 2020
3/3
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E HVG MOBILE HYD POWER UNIT RBS
Configuration: 336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Media Number -KENR8149-07 Publication Date -01/05/2014 Date Updated -29/05/2014
i06139756
Rear Power Take-Off (RPTO) - Install
SMCS - 1165-012-RE
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
(M 12 X 1.75 by 6 inch)
2
B 1P-0520 Driver Group 1
D 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g01103652
2/5
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g01103673
Illustration 3 g01103806
3/5
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 4 g01103675
1. Use Tooling (B) to install bearing (3) in flywheel housing (4) . The bearing joint is located at an
Angle (XX) that is 15 ± 3 degrees from the horizontal centerline. The oil hole in the bearing must
align with the oil gallery in the flywheel housing. The bearing should extend beyond the surface of
the flywheel housing by a Distance (YY) of 3.1 ± .5 mm (0.12 ± 0.02 inch).
2. Install dowels (1) in flywheel housing (4) . The dowels should extend beyond the surface of the
flywheel housing by a Distance (ZZ) of 3.5 ± .2 mm (0.14 ± 0.01 inch).
3. Install thrust washer (2) into flywheel housing (4) .
4. Place adapter assembly (10) on the work surface. The outside face should be down. Install bearing
(6) in adapter assembly (10) with Tooling (B) . The split in the bearing should be located at Angle
(X) , which is 45 ± 10 degrees from the centerline of adapter assembly (10) . The bearing should
extend beyond the surface of adapter assembly (10) by a Distance (Y) of 3.1 ± 0.5 mm (0.12 ± 0.02
inch).
5. Install dowels (8) and thrust washer (7) in adapter assembly (10) . The dowels should extend beyond
the surface of adapter assembly (10) by a Distance (Z) of 3.5 ± 0.2 mm (0.14 ± 0.01 inch).
6. Install O-ring seal (9) on adapter assembly (10) .
7. Use Tooling (D) to install lip seal (12) . Lubricate lip seal (12) lightly with the lubricant that is being
sealed. Lip seal (12) should be installed to a depth of 2.5 ± 0.5 mm (0.1 ± 0.02 inch).
8. Install PTO shaft (5) and adapter assembly (10) into flywheel housing (4) and install bolts (11) .
Ensure that the flat side of adapter assembly (10) is against the flywheel housing. This will ensure
that the oil passage is located toward the flywheel housing.
9. Install bearing (15) in idler gear (14) with Tooling (B) . Bearing Relief Groove (V) must line up with
Relief Groove (U) in idler gear (14) within 2 degrees. Bearing (15) must not extend beyond either
face of gear.
10. Install idler gear (14) on idler shaft (18) and bolts (19) and (20) . Install the shaft and gear assembly
in the flywheel housing.
11. Install Tooling (A) in the crankshaft. Install seal (16) and crankshaft gear (17) .
12. Install gasket (21) , cover (22) , and bolts (23) .
End By: Install the crankshaft rear seal.
4/5
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E HVG MOBILE HYD POWER UNIT RBS
Configuration: 336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Media Number -KENR8149-07 Publication Date -01/05/2014 Date Updated -29/05/2014
i06801192
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Illustration 1 g06119915
1. Remove bolts (1) and remove spacer (2). Remove vibration damper (3).
1/2
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g06119979
2. Remove bolts (4) and remove spacer (5). Remove pulley (6).
Installation Procedure
1. Install Vibration Damper (3) and Pulley (6) in the reverse order of removal.
a. Tighten bolts (4) to a torque of 200 ± 25 N·m (148 ± 18 lb ft).
b. Tighten bolts (1) to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 23:44:49 UTC+0800 2020
2/2
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E HVG MOBILE HYD POWER UNIT RBS
Configuration: 336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Media Number -KENR8149-07 Publication Date -01/05/2014 Date Updated -29/05/2014
i02272700
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B 1U-8145 Drill Bit 1
Start By:
a. Remove the crankshaft vibration damper and pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g01138207
1. Use Tooling (B) to carefully drill three evenly spaced holes in crankshaft front seal (1).
2. Alternate between the drilled holes and use Tooling (A) to remove crankshaft front seal (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 23:45:45 UTC+0800 2020
2/2
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E HVG MOBILE HYD POWER UNIT RBS
Configuration: 336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Media Number -KENR8149-07 Publication Date -01/05/2014 Date Updated -29/05/2014
i02272704
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C 1U-7430 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g01138218
Note: The crankshaft seal is designed to be installed dry.
1. Use Tooling (C) to install crankshaft front seal (1).
End By:
a. Install the crankshaft vibration damper and pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 23:46:40 UTC+0800 2020
2/2
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E HVG MOBILE HYD POWER UNIT RBS
Configuration: 336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Media Number -KENR8149-07 Publication Date -01/05/2014 Date Updated -29/05/2014
i05295976
Front Cover - Remove and Install
SMCS - 1166-010
Removal Procedure
Start By:
a. Remove vibration damper and pulley.
Illustration 1 g02149467
1. Remove bolt (1) and the belt tensioner (2). Remove bolts (3) and bolts (4). Remove stud
bolt (5) and front remove cover (6) and the gasket.
Installation Procedure
1. Install the front cover (6) in the reverse order of removal.
Thu Jul 30 23:47:36 UTC+0800 2020
1/2
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E HVG MOBILE HYD POWER UNIT RBS
Configuration: 336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3
Engines for Caterpillar Built Machines
Media Number -KENR8149-07 Publication Date -01/05/2014 Date Updated -29/05/2014
i03909335
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the crankshaft front seal.
b. Remove the camshaft.
Illustration 1 g01360127
1. Remove bolts (1) and remove engine mount (2).
1/2
336E L HVG UHD Mobile Hydraulic Power Unit RBS00001-UP (MACHINE) POWE...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...