This document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes:
1. Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2. Using a link bracket and driver group to remove the flywheel housing bolts.
3. Reversing the removal steps to install the flywheel housing, ensuring all components are clean prior to installation.
Caterpillar cat 323 d l excavator (prefix l5z) service repair manual (l5z0000...fjjsekmsmmes
The document provides instructions for removing and installing a flywheel, flywheel housing, and crankshaft rear seal on a Caterpillar C6.4 engine. The flywheel is removed using lifting tools and bolts, while the flywheel housing requires removing mounting bolts and seals. The crankshaft rear seal is removed using a slide hammer and distorter, and the new seal is installed using a locator, installer, and compound.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...shudun96087
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the flywheel, muffler brackets, and bolts to remove the housing. For installation, it describes lifting the housing back into place with a lifting device, reinstalling the bolts, and reattaching the muffler brackets. Precautions are provided to keep parts clean and contain fluids during the process.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...qme229722
This service repair manual provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar C6.4 engine. The flywheel is removed using lifting tools and bolts, while the flywheel housing is removed by first removing the electric starter motor, flywheel, and bolts. Gaskets and seals are also replaced during removal and installation of components. Tools required include link brackets, driver groups, and slide hammers.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...kesi7153062
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the flywheel, muffler brackets, and bolts to remove the housing. For installation, it describes lifting the housing back into place with a lifting device, reinstalling the bolts, and reattaching the muffler brackets. Precautions are provided to keep parts clean and contain fluids during the process.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, bolts securing the housing, and oil seal from the housing. It then describes how to install a new oil seal, gasket, and reattach the housing using bolts, and reinstall the flywheel and electric starting motor.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...fusjekkdmdmd2w
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...f8uesjdkdmdm
- The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine.
- To remove the housing, first remove the electric starting motor and flywheel. Then use tooling and a lifting device to remove the housing from the engine block.
- Reinstallation involves installing the housing back onto the engine block and reinstalling the flywheel and starting motor. Torques and safety precautions are also provided.
Caterpillar cat 323 d l excavator (prefix l5z) service repair manual (l5z0000...fjjsekmsmmes
The document provides instructions for removing and installing a flywheel, flywheel housing, and crankshaft rear seal on a Caterpillar C6.4 engine. The flywheel is removed using lifting tools and bolts, while the flywheel housing requires removing mounting bolts and seals. The crankshaft rear seal is removed using a slide hammer and distorter, and the new seal is installed using a locator, installer, and compound.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...shudun96087
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the flywheel, muffler brackets, and bolts to remove the housing. For installation, it describes lifting the housing back into place with a lifting device, reinstalling the bolts, and reattaching the muffler brackets. Precautions are provided to keep parts clean and contain fluids during the process.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...qme229722
This service repair manual provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar C6.4 engine. The flywheel is removed using lifting tools and bolts, while the flywheel housing is removed by first removing the electric starter motor, flywheel, and bolts. Gaskets and seals are also replaced during removal and installation of components. Tools required include link brackets, driver groups, and slide hammers.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...kesi7153062
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the flywheel, muffler brackets, and bolts to remove the housing. For installation, it describes lifting the housing back into place with a lifting device, reinstalling the bolts, and reattaching the muffler brackets. Precautions are provided to keep parts clean and contain fluids during the process.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, bolts securing the housing, and oil seal from the housing. It then describes how to install a new oil seal, gasket, and reattach the housing using bolts, and reinstall the flywheel and electric starting motor.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...fusjekkdmdmd2w
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...f8uesjdkdmdm
- The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine.
- To remove the housing, first remove the electric starting motor and flywheel. Then use tooling and a lifting device to remove the housing from the engine block.
- Reinstallation involves installing the housing back onto the engine block and reinstalling the flywheel and starting motor. Torques and safety precautions are also provided.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...8ufjsekddm8u
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, bolts securing the housing, and oil seal from the housing. It then describes how to install a new oil seal, gasket, and reattach the housing using bolts, and reinstall the flywheel and electric starting motor.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...ufjksemd8ujd
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...km7seydwuhdw
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...jdkskmdmdm
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...prmy389342
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar cat 323 d l excavator (prefix ysd) service repair manual (ysd0000...fjjskekdmmme
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It lists the required tools and presents a step-by-step procedure that includes removing bolts and washers, lifting the housing off using a bracket and lifting device, removing the oil seal, cleaning surfaces, installing a new gasket and seal, and securing the housing back in place.
Caterpillar cat 323 d l excavator (prefix ysd) service repair manual (ysd0000...fjjsekmsmmes
The document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar C6.4 engine. To remove the flywheel, technicians must first remove the crankshaft position sensor and muffler, then use lifting tools to pull the flywheel from the housing. To remove the flywheel housing, technicians must first remove the electric starting motor and flywheel, then unbolt the housing from the cylinder block and lift it away. Reinstallation follows the reverse process, ensuring clean mating surfaces and proper torques on bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...shudun96087
- The document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar C6.4 engine.
- To remove the flywheel, technicians must first remove the muffler and crankshaft position sensor, then use tools to lift the flywheel out of the housing. The flywheel weighs approximately 50 kg.
- Installation involves using tools to lift the flywheel into place, torquing the bolts to specifications, and reinstalling the crankshaft position sensor and muffler.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...qme229722
- The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine used in 323D L excavators.
- To remove the flywheel housing, the electric starting motor and flywheel must first be removed. Bolts securing the housing are then removed using lifting equipment, and the gasket and oil seal are replaced.
- Installation is the reverse of removal, with new gaskets and seals installed and bolts torqued to specification to secure the housing.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...kesi7153062
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor and flywheel first. Then it instructs to remove housing bolts and install a lifting device to remove the housing. For installation, it describes cleaning the housing, installing with new bolts, and checking runout.
Caterpillar Cat 312D and 312D L Excavator (Prefix KES) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes removing the electric starting motor and flywheel first. Then it lists the required tools and outlines the steps to remove the housing using a link bracket and driver group. The installation procedure is not described, but refers the technician back to previous sections to reinstall the flywheel and starting motor.
Caterpillar Cat 312D and 312D L Excavator (Prefix KES) Service Repair Manual ...zan2736ban
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes removing the electric starting motor and flywheel first. Then it lists the required tools and outlines the steps to remove the housing using a link bracket and driver group. The installation procedure is not described, but refers the technician back to instructions for reinstalling the flywheel, electric starting motor, and other components.
Caterpillar Cat 312D L Excavator (Prefix KES) Service Repair Manual (KES00001...fusjekkdmdmd2w
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing.
3) Installing a new gasket and replacing the oil seal before reinstalling the housing.
4) Reinstalling the flywheel housing with new bolts and washers and reinstalling the flywheel and electric starting motor.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes removing the electric starting motor and flywheel first. Then it lists the required tools and outlines the steps to remove the housing using a link bracket and driver group. The installation procedure is not described, but refers the technician back to previous sections to reinstall the flywheel and starting motor.
Caterpillar Cat 312D L Excavator (Prefix KES) Service Repair Manual (KES00001...f8usejkddmmd
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes removing the electric starting motor and flywheel first. Then it lists the required tools and outlines the steps to remove the housing using a link bracket and driver group. The installation procedure is not described, but refers the technician back to previous sections to reinstall the flywheel and starting motor.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes removing the electric starting motor and flywheel first. Then it lists the required tools and outlines the steps to remove the housing using a link bracket and driver group. The installation procedure is not described, but refers the technician to first install the flywheel and then the electric starting motor.
Caterpillar cat 312 d l excavator (prefix kes) service repair manual (kes0000...ikdkdmdm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes removing the electric starting motor and flywheel first. Then it lists the required tools and outlines the steps to remove the housing using a link bracket and driver group. The installation procedure is not described, but refers the technician back to instructions for reinstalling the flywheel, electric starting motor, and any other parts previously removed.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...ikdkdmdm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...jdkskmdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using tools to install the bushing, idler shaft, idler gear, thrust plate, washer, and idler gear bolt while ensuring proper gear alignment and backlash. Tolerances for backlash and clearances are provided.
This document provides instructions for disassembling and assembling the travel motor of 324E and 324E LN excavators. The disassembly process involves removing 28 components from the travel motor in 27 steps. The assembly process reverses the disassembly with 28 steps and provides guidance on cleaning, lubricating, and installing components in the correct orientation. Tools required include retaining ring pliers, drivers, pullers, and adapters to securely hold components during disassembly and assembly.
More Related Content
Similar to Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001 and up).pdf
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...8ufjsekddm8u
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, bolts securing the housing, and oil seal from the housing. It then describes how to install a new oil seal, gasket, and reattach the housing using bolts, and reinstall the flywheel and electric starting motor.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...ufjksemd8ujd
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...km7seydwuhdw
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...jdkskmdmdm
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...prmy389342
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove bolts securing the housing and take it off the cylinder block.
3) Removing the oil seal from the housing using a driver group tool.
4) Cleaning surfaces, installing a new gasket, and reattaching the housing with bolts.
Caterpillar cat 323 d l excavator (prefix ysd) service repair manual (ysd0000...fjjskekdmmme
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It lists the required tools and presents a step-by-step procedure that includes removing bolts and washers, lifting the housing off using a bracket and lifting device, removing the oil seal, cleaning surfaces, installing a new gasket and seal, and securing the housing back in place.
Caterpillar cat 323 d l excavator (prefix ysd) service repair manual (ysd0000...fjjsekmsmmes
The document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar C6.4 engine. To remove the flywheel, technicians must first remove the crankshaft position sensor and muffler, then use lifting tools to pull the flywheel from the housing. To remove the flywheel housing, technicians must first remove the electric starting motor and flywheel, then unbolt the housing from the cylinder block and lift it away. Reinstallation follows the reverse process, ensuring clean mating surfaces and proper torques on bolts.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...shudun96087
- The document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar C6.4 engine.
- To remove the flywheel, technicians must first remove the muffler and crankshaft position sensor, then use tools to lift the flywheel out of the housing. The flywheel weighs approximately 50 kg.
- Installation involves using tools to lift the flywheel into place, torquing the bolts to specifications, and reinstalling the crankshaft position sensor and muffler.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...qme229722
- The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine used in 323D L excavators.
- To remove the flywheel housing, the electric starting motor and flywheel must first be removed. Bolts securing the housing are then removed using lifting equipment, and the gasket and oil seal are replaced.
- Installation is the reverse of removal, with new gaskets and seals installed and bolts torqued to specification to secure the housing.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...kesi7153062
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor and flywheel first. Then it instructs to remove housing bolts and install a lifting device to remove the housing. For installation, it describes cleaning the housing, installing with new bolts, and checking runout.
Caterpillar Cat 312D and 312D L Excavator (Prefix KES) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes removing the electric starting motor and flywheel first. Then it lists the required tools and outlines the steps to remove the housing using a link bracket and driver group. The installation procedure is not described, but refers the technician back to previous sections to reinstall the flywheel and starting motor.
Caterpillar Cat 312D and 312D L Excavator (Prefix KES) Service Repair Manual ...zan2736ban
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes removing the electric starting motor and flywheel first. Then it lists the required tools and outlines the steps to remove the housing using a link bracket and driver group. The installation procedure is not described, but refers the technician back to instructions for reinstalling the flywheel, electric starting motor, and other components.
Caterpillar Cat 312D L Excavator (Prefix KES) Service Repair Manual (KES00001...fusjekkdmdmd2w
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing.
3) Installing a new gasket and replacing the oil seal before reinstalling the housing.
4) Reinstalling the flywheel housing with new bolts and washers and reinstalling the flywheel and electric starting motor.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes removing the electric starting motor and flywheel first. Then it lists the required tools and outlines the steps to remove the housing using a link bracket and driver group. The installation procedure is not described, but refers the technician back to previous sections to reinstall the flywheel and starting motor.
Caterpillar Cat 312D L Excavator (Prefix KES) Service Repair Manual (KES00001...f8usejkddmmd
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes removing the electric starting motor and flywheel first. Then it lists the required tools and outlines the steps to remove the housing using a link bracket and driver group. The installation procedure is not described, but refers the technician back to previous sections to reinstall the flywheel and starting motor.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes removing the electric starting motor and flywheel first. Then it lists the required tools and outlines the steps to remove the housing using a link bracket and driver group. The installation procedure is not described, but refers the technician to first install the flywheel and then the electric starting motor.
Caterpillar cat 312 d l excavator (prefix kes) service repair manual (kes0000...ikdkdmdm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes removing the electric starting motor and flywheel first. Then it lists the required tools and outlines the steps to remove the housing using a link bracket and driver group. The installation procedure is not described, but refers the technician back to instructions for reinstalling the flywheel, electric starting motor, and any other parts previously removed.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...ikdkdmdm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
Similar to Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001 and up).pdf (20)
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...jdkskmdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using tools to install the bushing, idler shaft, idler gear, thrust plate, washer, and idler gear bolt while ensuring proper gear alignment and backlash. Tolerances for backlash and clearances are provided.
This document provides instructions for disassembling and assembling the travel motor of 324E and 324E LN excavators. The disassembly process involves removing 28 components from the travel motor in 27 steps. The assembly process reverses the disassembly with 28 steps and provides guidance on cleaning, lubricating, and installing components in the correct orientation. Tools required include retaining ring pliers, drivers, pullers, and adapters to securely hold components during disassembly and assembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations guide removal of additional components like the flywheel housing, crankshaft pulley, and crankshaft front seal. Tools and safety precautions are also listed.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, counterbalance valve housing assembly, and more. Safety notices are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, wrenches, and other equipment.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...jdkskmdmdm
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like bolts, covers, seals, springs, pistons, gears, and bearings. The corresponding 51 steps for assembly install these same components in reverse order, noting the tools required and proper installation of seals, bearings, and retaining rings. Precautions are included for released spring forces during disassembly and heating components during assembly.
Caterpillar Cat 330F L Excavator (Prefix GHT) Service Repair Manual (GHT00001...jdkskmdmdm
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and ensuring fluids are contained.
This document provides assembly instructions for repairing a hydraulic pump in 3 steps:
1. Install various internal components like bearings, seals, and pistons into the pump housing.
2. Attach the pump housing to the pump head and install additional external components.
3. Assemble the pump control mechanism by installing springs, pistons, and covers.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing using specialized tools over 30 detailed steps. Cleanliness is emphasized throughout to prevent dirt contamination during reassembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1. The flywheel, flywheel housing, crankshaft rear seal, and vibration damper and pulley. Tools and torque specifications are listed for each procedure.
2. Removing the crankshaft rear seal involves drilling holes in the seal and pulling it out with a slide hammer tool. Installing the new seal uses a seal installation tool.
3. Removing the flywheel housing first requires removing mounting bolts and the flywheel. Installing applies sealant and mounts the housing with bolts.
4. Instructions are provided to remove the crankshaft front
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precise tools and cleaning of parts is emphasized.
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs technicians to clean all parts thoroughly, apply lubricants where specified, and install over 30 parts into the final drive housing in the reverse order of disassembly using various tools. Technicians are advised to replace all seals, gaskets and O-rings during assembly and to keep all parts clean.
The document provides instructions for disassembling and assembling the piston motor (hydraulic fan) on 325C and 325C L excavator models. The disassembly procedure involves 22 steps to remove components like the key, cover, port plate, bearings, plugs, sleeves, pistons and housing. The assembly procedure describes 16 steps including pressing components, installing seals, pins and rings in the proper order and orientation to rebuild the piston motor. Cleanliness and applying a light oil film to parts is emphasized throughout.
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
This document provides instructions for removing and installing various components of the crankshaft and flywheel housing on a 325C Excavator. It describes how to remove and install the flywheel, crankshaft rear seal, rear seal carrier, and flywheel housing. The procedures include lists of required tools and step-by-step instructions describing how to remove each component and install the replacement parts. Safety notices are provided to keep parts clean and contain fluids appropriately during the repair work.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...jdkskmdmdm
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists the required tools and outlines 16 steps to disassemble parts like the traction control valve, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
1) The document provides disassembly instructions for components of a 313D excavator including the final drive, travel motor, counterbalance valve, and traction control valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification marks and order of components.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, plates, and seals. Proper handling and storage of fluids is also addressed.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...jdkskmdmdm
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, installing new gaskets, and tightening bolts in a specific sequence using torque wrenches and degree wheels to ensure proper torque.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...jdkskmdmdm
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 323D L MOBILE HYD POWER UNIT L5Z
Configuration: 323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02743771
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B Forcing bolts M16 - 2 by 120 mm 2
Start By:
a. Remove the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
b. Remove the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01374966
1. Remove muffler brackets (1).
Illustration 2 g01374968
Illustration 3 g01374970
2. Remove bolts (2).
3. Install Tooling (A) and a suitable lifting device onto flywheel (3).
4. Use Tooling (B) in order to remove flywheel (3) out of the housing. The weight of flywheel
(3) is approximately 50 kg (110 lb).
2/3
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 5. Perform the following procedure in order to remove the flywheel ring gear.
Illustration 4 g01374977
Typical Example
a. Place flywheel (3) and ring gear (4) on suitable cribbing.
Note: Mark the orientation of ring gear (4) on flywheel (3) for assembly purposes.
Always wear protective gloves when handling parts that have been
heated.
b. Raise the temperature of ring gear (4) uniformly.
c. Remove the ring gear (4) by tapping ring gear (4) all the way around flywheel (3).
d. Reposition flywheel (3) in order to remove ring gear (4).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 30 14:46:17 UTC+0800 2020
3/3
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 323D L MOBILE HYD POWER UNIT L5Z
Configuration: 323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02744399
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Raise the temperature of the ring gear 149 °C (300 °F).
1/3
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. b. Use a suitable press in order to install the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g01374993
2. Install Tooling (A) and a suitable lifting device onto flywheel (3).
3. Install flywheel (3). The weight of flywheel (3) is approximately 50 kg (110 lb).
Illustration 2 g01374968
4. Install bolts (2) in order to secure flywheel (3) onto the crankshaft. Tighten bolts (2) to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tooling (A) from flywheel (3).
2/3
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 3 g01374966
6. Install muffler brackets (1).
7. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
End By:
a. Install the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
b. Install the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 30 14:47:16 UTC+0800 2020
3/3
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 323D L MOBILE HYD POWER UNIT L5Z
Configuration: 323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 323D L MOBILE HYD POWER UNIT L5Z
Configuration: 323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 30 14:49:15 UTC+0800 2020
3/3
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 323D L MOBILE HYD POWER UNIT L5Z
Configuration: 323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742697
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
b. Remove the flywheel and ring gear. Refer to Disassembly and Assembly, "Flywheel -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g01374571
1. Install Tooling (A), and a suitable lifting device onto flywheel housing (3).
2. Remove bolts (2) and the washers that secure flywheel housing (3) to the cylinder block.
3. Remove flywheel housing (3). The weight of flywheel (3) is approximately 29 kg (65 lb).
4. Remove gasket (1) (not shown).
Illustration 2 g01374572
5. Use Tooling (B) in order to remove the oil seal (4) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
NOTICE
2/4
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01374614
1. Use Tooling (B) in order to install the oil seal (4) (not shown).
Illustration 4 g01374571
2. Check the condition of two dowels (not shown). If dowels are damaged, use new parts for
replacement.
3. Clean old gasket (1) (not shown) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
4. Place flywheel housing (3) in position on the cylinder block.
5. Install the washers and bolts (2) in order to secure flywheel housing (3) to the cylinder
block.
6. Remove Tooling (A).
End By:
3/4
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 30 14:50:14 UTC+0800 2020
4/4
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 323D L MOBILE HYD POWER UNIT L5Z
Configuration: 323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i06790404
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket(1)
1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Remove the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
1/4
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g00604778
2. Use Tooling (B) in order to remove nut (1) and washer (2) from the threaded end of the
crankshaft.
Illustration 2 g00604784
3. Use Tooling (A) in order to remove crankshaft pulley (3) from the engine.
2/4
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 3 g00604792
4. If it is necessary to remove wear sleeve (4) from crankshaft pulley (3), use a suitable
hammer and a suitable chisel. Hold the suitable chisel at right angles to the surface of the
wear sleeve. Tap the wear sleeve in three places. You can remove the wear sleeve once the
tension is released.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 6V-9120 Socket(1)
1
C 1P-0510 Driver Gp 1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Raise the temperature of the wear sleeve. Use Tooling (C) in order to install the wear sleeve
onto the crankshaft pulley.
3/4
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 4 g01377941
2. Ensure that baffle plate (5) is oriented, as shown.
Illustration 5 g00604778
3. Position crankshaft pulley (3) onto the engine.
4. Install washer (2) and nut (1). Use Tooling (B) in order to tighten nut (1) to a torque of
707.5 ± 57.5 N·m (522 ± 42 lb ft).
5. Install the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 30 14:51:13 UTC+0800 2020
4/4
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 323D L MOBILE HYD POWER UNIT L5Z
Configuration: 323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742689
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
Typical Example
1. Drill three evenly spaced 3.0 mm (0.12 inch) holes in crankshaft front seal (1).
2. Use Tooling (A) in order to remove crankshaft front seal (1). Remove the seal evenly by
alternating the position of Tooling (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 30 14:52:13 UTC+0800 2020
2/2
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 323D L MOBILE HYD POWER UNIT L5Z
Configuration: 323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742692
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g00612743
Typical Example
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Use Tooling (A) in order to install new crankshaft front seal (1) in the front housing.
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 30 14:53:12 UTC+0800 2020
2/2
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 323D L MOBILE HYD POWER UNIT L5Z
Configuration: 323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742863
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
2/4
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 2 g01374789
1. Remove idler gear bolt (5) and the washer from the idler gear shaft .
2. Remove thrust plate (6) from the idler gear shaft.
Illustration 3 g01374793
3. Remove idler gear (2) from the idler gear shaft.
Illustration 4 g01374804
4. If necessary, use Tooling (B) and a suitable press in order to remove bushing (7) (not
shown) from idler gear (2).
3/4
323D L Mobile Hydraulic Power Unit L5Z00001-UP (MACHINE) POWERED BY C...
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...