1) The document provides instructions for removing and installing various engine components, including the engine oil filter base, engine oil cooler, hydraulic oil cooler, and air cleaner.
2) The procedures note that cleanliness is important and tools may be required for some removal and installation steps.
3) Technicians are advised to follow the steps carefully to correctly disassemble and reassemble the components.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR L5K
Configuration: 336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit C9 Engine Supplement
Media Number -RENR8647-16 Publication Date -01/10/2015 Date Updated -26/10/2015
i02417234
Engine Oil Filter Base - Disassemble
SMCS - 1306-015; 1306
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
1/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01208235
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 1. Remove connector (20) and O-ring seal (19).
2. Remove cover (18) and O-ring seal (16).
3. Remove stud (17).
4. Remove connector (14) and O-ring seal (15).
5. Remove adapter (12) and O-ring seal (10).
6. Remove plug (2) and O-ring seal (3).
7. Remove plug (13), O-ring seal (11), spring (9), and valve (8) from engine oil filter base (1).
8. Remove plug (4), O-ring seal (5), spring (6), and valve (7) from engine oil filter base (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 07:27:43 UTC+0800 2020
3/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR L5K
Configuration: 336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit C9 Engine Supplement
Media Number -RENR8647-16 Publication Date -01/10/2015 Date Updated -26/10/2015
i02417236
Engine Oil Filter Base - Assemble
SMCS - 1306-016; 1306
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g01208235
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 1. Install valve (7), spring (6), O-ring seal (5), and plug (4) into engine oil filter base (1).
2. Install valve (8), spring (9), O-ring seal (11), and plug (13) into engine oil filter base (1).
3. Install O-ring seal (3) and plug (2).
4. Install O-ring seal (10) and adapter (12).
5. Install O-ring seal (15) and connector (14).
6. Install stud (17).
7. Install O-ring seal (16) and cover (18).
8. Install O-ring seal (19) and connector (20).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 07:28:38 UTC+0800 2020
3/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR L5K
Configuration: 336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit C9 Engine Supplement
Media Number -RENR8647-16 Publication Date -01/10/2015 Date Updated -26/10/2015
i02417231
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M8 - 1.25 by 65 mm
2
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01208181
1/4
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 1. Install the gasket and engine oil filter base (10) over Tooling (A).
2. Install bolts (9).
Illustration 2 g01208179
Illustration 3 g01208224
3. Remove Tooling (A) and install bolts (8). Refer to Illustration 3 for the correct tightening
sequence.
2/4
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 4 g01208178
4. Connect hose assemblies (6) and (7).
Illustration 5 g01208176
5. Install hose (5).
Illustration 6 g01208119
6. Close engine hood (4).
3/4
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 7 g01208173
7. Connect hose assembly (3).
Illustration 8 g01208170
8. Raise guard (2) and install bolts (1).
9. fill the engine with coolant. Refer to Operation and Maintenance Manual, "Refill
Capacities".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 07:29:34 UTC+0800 2020
4/4
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR L5K
Configuration: 336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit C9 Engine Supplement
Media Number -RENR8647-16 Publication Date -01/10/2015 Date Updated -26/10/2015
i02417228
Engine Oil Cooler - Remove and Install
SMCS - 1378-010
Removal Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g01208148
1. Remove gasket (1) and engine oil cooler (2).
Installation Procedure
1/2
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 2 g01208148
1. Install engine oil cooler (2) and gasket (1).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 07:30:30 UTC+0800 2020
2/2
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR L5K
Configuration: 336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit C9 Engine Supplement
Media Number -RENR8647-16 Publication Date -01/10/2015 Date Updated -26/10/2015
i02415509
Hydraulic Oil Cooler - Remove and Install
SMCS - 1374-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 189-0408 Shackle As 2
Start By:
a. Remove the fan group. Refer to Disassembly and Assembly, "Fan Group (Includes Fan, Fan
Guard, Fan Shroud, and Hydraulic Fan Motor) - Remove".
Illustration 1 g01207524
1. Remove hose (1), bolts (2), and plate (3).
1/5
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g01207525
2. Remove bolts (4) and bracket (5).
Illustration 3 g01207526
3. Attach Tooling (A) and a suitable lifting device to hydraulic oil cooler (6). The weight of
hydraulic oil cooler (6) is approximately 68 kg (150 lb).
4. Remove bolt (7).
Illustration 4 g01207527
5. Remove bolts (8).
2/5
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 5 g01207528
6. Use the suitable lifting device to remove hydraulic oil cooler (6).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 189-0408 Shackle As 2
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 6 g01207528
1. Use Tooling (A) and a suitable lifting device to position hydraulic oil cooler (6). The weight
of hydraulic oil cooler (6) is approximately 68 kg (150 lb).
3/5
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 7 g01207527
2. Install bolts (8).
Illustration 8 g01207526
3. Install bolt (7) and remove Tooling (A) from hydraulic oil cooler (6).
Illustration 9 g01207525
4. Install bracket (5) and bolts (4).
4/5
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 10 g01207524
5. Install plate (3), bolts (2), and hose (1).
End By:
a. Install the fan group. Refer to Disassembly and Assembly, "Fan Group (Includes Fan, Fan
Guard, Fan Shroud, and Hydraulic Fan Motor) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 07:31:26 UTC+0800 2020
5/5
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR L5K
Configuration: 336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit C9 Engine Supplement
Media Number -RENR8647-16 Publication Date -01/10/2015 Date Updated -26/10/2015
i02412726
Air Cleaner - Remove and Install
SMCS - 1051-010; 1054-010
Removal Procedure
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g01205948
1. Open doors (2) and (1).
1/6
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g01206308
2. Remove cover (3).
Illustration 3 g01206309
Illustration 4 g01206310
3. Remove primary filter element (4) and secondary filter element (5).
2/6
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 5 g01206311
4. Disconnect hose (6) from the back of air cleaner assembly (7).
Illustration 6 g01206312
5. Remove bolts (8) and air cleaner assembly (7).
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
3/6
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 7 g01206312
1. Install air cleaner assembly (7) and bolts (8).
Illustration 8 g01206311
2. Connect hose (6) to the back of air cleaner assembly (7).
Illustration 9 g01206310
4/6
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 10 g01206309
3. Install secondary filter element (5) and primary filter element (4).
Illustration 11 g01206308
4. Install cover (3).
Illustration 12 g01205948
5. Close doors (1) and (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Fri Aug 21 07:32:21 UTC+0800 2020
5/6
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR L5K
Configuration: 336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit C9 Engine Supplement
Media Number -RENR8647-16 Publication Date -01/10/2015 Date Updated -26/10/2015
i02412735
Ether Start Valve - Remove and Install
SMCS - 1456-010-VL
Removal Procedure
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
Illustration 1 g01205948
1. Open doors (2) and (1).
1/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 2 g01205972
2. Disconnect harness assembly (3) and tube assembly (6).
3. Remove bolts (4) and ether start valve (5).
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 3 g01205972
1. Position ether start valve (5) and install bolts (4).
2. Connect harness assembly (3) and tube assembly (6).
2/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 4 g01205948
3. Close doors (1) and (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 07:33:17 UTC+0800 2020
3/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...