1. The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators.
2. The disassembly procedure includes using various tools to remove over 30 individual parts from the pump in the correct order.
3. Reassembly requires carefully installing each part in the reverse order, ensuring proper placement and installation of seals, bearings, springs and other components.
4. Cleanliness is emphasized as important during both disassembly and assembly to prevent dirt from damaging internal parts.
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF0000...f8uesjdkdmdm
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reinstalls the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring-loaded parts.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...ikdkdmddm
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reinstalls the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring-loaded parts.
Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF0000...f8uejkkdmdm8u
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF0000...f8uejkkdmdm8u
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF0000...f8uesjdkdmdm
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reinstalls the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring-loaded parts.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...ikdkdmddm
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reinstalls the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring-loaded parts.
Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF0000...f8uejkkdmdm8u
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF0000...f8uejkkdmdm8u
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reinstalls the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring-loaded parts.
Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF0000...fujjekdmdmd
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF0000...8ufjsekddm8u
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components into the pump housing in the proper order. Disassembly instructions describe 8 steps for removing these components in reverse order, noting any safety precautions for spring loaded parts. Tools required are also listed.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other internal components. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...ze3xiandiao
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF0000...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reinstalls the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring-loaded parts.
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include draining oil, removing covers and shafts, using lifting tools to remove heavy components, and reinstalling parts in reverse order while applying new seals and grease. Detailed diagrams show tooling and component locations to aid the process.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar 3046 engine. The removal procedure involves removing the front housing, idler gear bolt, thrust plate, idler gear, idler shaft, and front plate. The installation procedure instructs to install the front plate and idler shaft, align the timing marks, and install the idler gear, thrust plate, and idler gear bolt. References are provided for removing and installing the other gears in the front gear group.
The document provides removal and installation instructions for a variable valve actuator oil pressure sensor, variable valve actuator oil pressure solenoid, water pump, water pump disassembly and assembly, water temperature regulator housing, and precooler from a C18 industrial engine. The instructions include lists of required tools and step-by-step procedures with illustrations to guide removal and installation of the components. Safety notices are provided to contain fluids, keep parts clean, and dispose of fluids properly.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting parts before installation and applying thread locking compound to bolts.
2. Installing the front plate, gears, and shafts in the correct order and orientation while adjusting backlash.
3. Torque specifications for installing bolts and nuts.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page document that includes:
1) A list of required tools and safety notices for the removal procedure. The procedure involves removing bolts, lifting devices, and a gasket from the flywheel housing.
2) A list of required tools and safety notices for the installation procedure. The procedure involves cleaning, applying sealant, positioning a gasket and flywheel housing, and tightening bolts in a specific sequence and torque.
3) The document concludes by stating additional installation steps to complete the job.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Removing and installing the fuel priming pump.
- Removing the fuel filter base and disassembling/assembling its components.
- Removing and installing the fuel transfer pump.
- Removing the electronic unit injectors.
The summaries provide concise overviews of the removal and installation procedures for each component in 3 sentences or less.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C18 Industrial Engine, including:
1) Removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) Disassembling and assembling the fuel filter base to replace seals and fittings.
3) Procedures include disconnecting fuel lines and electrical connections, marking parts for reinstallation, and applying thread lock compounds. Safety notices advise containing fluids and preventing contamination.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base on the engine and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
The document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger on a C9.3 Industrial Engine. Key steps include draining fluids, removing connecting components, cleaning parts, applying sealants, and torquing fasteners to the specified values. Required tools include pry bars, brushes, vacuum equipment, and wrenches. Cautions are provided regarding containing fluids and preventing contamination.
1. The document provides instructions for removing and installing the crankshaft front seal on a C18 industrial engine.
2. The removal procedure involves using various tools like a slide hammer puller and pry bar to remove the existing seal and wear sleeve.
3. The installation procedure lists the required tools and instructs to use a seal locator, installer, and bolts to properly position and set the new seal and wear sleeve.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C11 engine, including:
1. Removing the rear gear group which involves removing multiple gears, seals, bolts and covers.
2. Removing the flywheel which requires attaching lifting equipment and removing bolts.
3. Installing the rear gear group and flywheel which provides detailed steps and specifications for installing components like bearings and seals.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine, including:
1. Valves, springs, retainers, and rotators. Tools are needed to compress springs during removal and installation.
2. Valve guides. Guides are removed and installed using driver tools to the proper height above the cylinder head.
3. Valve seat inserts. Seat inserts are removed and installed using specialized driver tools for the inlet and exhaust valves.
4. The engine oil filter base and filter. Hoses are disconnected and bolts removed to take off the base and gasket. A strap wrench is recommended to remove the oil filter.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document contains illustrations and lists required tools for each procedure.
This document provides instructions for disassembling and assembling the freewheel stator component of a torque converter. The disassembly process involves using various tools to remove over 30 individual parts in a specific sequence. Cleanliness is emphasized. The assembly process reverses the disassembly steps and provides additional details like proper orientation and torque specifications for reinstalling components.
More Related Content
Similar to Caterpillar Cat 336D L Excavator (Prefix PPN) Service Repair Manual (PPN00001 and up).pdf
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reinstalls the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring-loaded parts.
Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF0000...fujjekdmdmd
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF0000...8ufjsekddm8u
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components into the pump housing in the proper order. Disassembly instructions describe 8 steps for removing these components in reverse order, noting any safety precautions for spring loaded parts. Tools required are also listed.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other internal components. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...ze3xiandiao
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF0000...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reinstalls the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring-loaded parts.
Similar to Caterpillar Cat 336D L Excavator (Prefix PPN) Service Repair Manual (PPN00001 and up).pdf (7)
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include draining oil, removing covers and shafts, using lifting tools to remove heavy components, and reinstalling parts in reverse order while applying new seals and grease. Detailed diagrams show tooling and component locations to aid the process.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar 3046 engine. The removal procedure involves removing the front housing, idler gear bolt, thrust plate, idler gear, idler shaft, and front plate. The installation procedure instructs to install the front plate and idler shaft, align the timing marks, and install the idler gear, thrust plate, and idler gear bolt. References are provided for removing and installing the other gears in the front gear group.
The document provides removal and installation instructions for a variable valve actuator oil pressure sensor, variable valve actuator oil pressure solenoid, water pump, water pump disassembly and assembly, water temperature regulator housing, and precooler from a C18 industrial engine. The instructions include lists of required tools and step-by-step procedures with illustrations to guide removal and installation of the components. Safety notices are provided to contain fluids, keep parts clean, and dispose of fluids properly.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting parts before installation and applying thread locking compound to bolts.
2. Installing the front plate, gears, and shafts in the correct order and orientation while adjusting backlash.
3. Torque specifications for installing bolts and nuts.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page document that includes:
1) A list of required tools and safety notices for the removal procedure. The procedure involves removing bolts, lifting devices, and a gasket from the flywheel housing.
2) A list of required tools and safety notices for the installation procedure. The procedure involves cleaning, applying sealant, positioning a gasket and flywheel housing, and tightening bolts in a specific sequence and torque.
3) The document concludes by stating additional installation steps to complete the job.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Removing and installing the fuel priming pump.
- Removing the fuel filter base and disassembling/assembling its components.
- Removing and installing the fuel transfer pump.
- Removing the electronic unit injectors.
The summaries provide concise overviews of the removal and installation procedures for each component in 3 sentences or less.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C18 Industrial Engine, including:
1) Removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) Disassembling and assembling the fuel filter base to replace seals and fittings.
3) Procedures include disconnecting fuel lines and electrical connections, marking parts for reinstallation, and applying thread lock compounds. Safety notices advise containing fluids and preventing contamination.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base on the engine and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
The document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger on a C9.3 Industrial Engine. Key steps include draining fluids, removing connecting components, cleaning parts, applying sealants, and torquing fasteners to the specified values. Required tools include pry bars, brushes, vacuum equipment, and wrenches. Cautions are provided regarding containing fluids and preventing contamination.
1. The document provides instructions for removing and installing the crankshaft front seal on a C18 industrial engine.
2. The removal procedure involves using various tools like a slide hammer puller and pry bar to remove the existing seal and wear sleeve.
3. The installation procedure lists the required tools and instructs to use a seal locator, installer, and bolts to properly position and set the new seal and wear sleeve.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C11 engine, including:
1. Removing the rear gear group which involves removing multiple gears, seals, bolts and covers.
2. Removing the flywheel which requires attaching lifting equipment and removing bolts.
3. Installing the rear gear group and flywheel which provides detailed steps and specifications for installing components like bearings and seals.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine, including:
1. Valves, springs, retainers, and rotators. Tools are needed to compress springs during removal and installation.
2. Valve guides. Guides are removed and installed using driver tools to the proper height above the cylinder head.
3. Valve seat inserts. Seat inserts are removed and installed using specialized driver tools for the inlet and exhaust valves.
4. The engine oil filter base and filter. Hoses are disconnected and bolts removed to take off the base and gasket. A strap wrench is recommended to remove the oil filter.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document contains illustrations and lists required tools for each procedure.
This document provides instructions for disassembling and assembling the freewheel stator component of a torque converter. The disassembly process involves using various tools to remove over 30 individual parts in a specific sequence. Cleanliness is emphasized. The assembly process reverses the disassembly steps and provides additional details like proper orientation and torque specifications for reinstalling components.
This document provides instructions for disassembling and assembling the torque converter of a 966H wheel loader. It begins with required tools and safety notices. The disassembly instructions describe removing over 30 individual parts in multiple steps, including the torque converter housing, impeller, stator, carrier shaft, and turbine. The assembly section then lists the components and provides the reverse order for reassembling the torque converter. Cleanliness is emphasized as important during disassembly and assembly.
This document provides instructions for removing and installing various components of the rear differential and carrier assembly of a Caterpillar 966C wheel loader, including removing the rear axles, disconnecting air lines, removing mounting bolts and lifting the rear of the machine to access the differential and carrier. The rear differential and carrier unit weighs 350 pounds and houses the internal gearing that allows the rear wheels to turn at different speeds while receiving equal torque.
This document provides instructions for disassembling and assembling the piston pump of a 962K wheel loader steering system. The disassembly procedure has 28 steps that remove components like valves, spools, springs, and bearings. The assembly procedure reverses this with 31 steps, ensuring O-rings and springs are correctly installed to prevent injury. Precautions are provided to safely release spring forces during disassembly and assembly.
The document provides instructions for removing and installing a secondary steering pump and electric motor on a Caterpillar 962K wheel loader. It outlines 28 steps for disassembly of the pump which include removing valves, spools, plugs, springs and other components. The assembly section lists 34 steps for reinstalling the parts in reverse order and adjusting axial shaft end play clearance.
This document provides instructions for removing and installing various engine components on a Caterpillar 950B wheel loader, including the spacer plate, water directors, lifter group, camshaft, and camshaft bearings. The procedures describe removing each part, checking part dimensions, cleaning surfaces, lubricating, and correctly installing each part while maintaining proper engine timing. Tools required are also listed.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR PPN
Configuration: 336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02732015
Piston Pump (Hydraulic Fan) - Assemble
SMCS - 1387-016-QP; 5070-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1857 Retaining Ring Pliers 1
D 8T-5096 Dial Indicator Gp 1
Illustration 1 g01212915
1. Lower the temperature of bearing cup (49). Install bearing cup (49).
1/11
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g01212913
2. Install lip seal (48).
3. Use Tooling (B) in order to install retaining ring (47).
Illustration 3 g01213404
4. Raise the temperature of bearing cone (46).
5. Install bearing cone (46) onto shaft (45).
Illustration 4 g01213405
6. Install bearing cone (46), shaft (45), and bearing cone (31).
2/11
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 5 g01213407
7. Lower the temperature of bearing cone (26). Install bearing cone (26).
Illustration 6 g01212900
8. Position head (23) onto the housing.
9. Install bolts (22).
Illustration 7 g01213409
10. Use Tooling (D) in order to determine the end play of shaft (45).
3/11
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 11 g01212910
14. Install swashplate (43).
Illustration 12 g01373818
15. Install shim (40), spring (41), and shim (42) to barrel (38).
Illustration 13 g01212908
5/11
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
16. Use Tooling (A), Tooling (B), and a suitable press in order to install retaining ring (39) into
barrel (38).
Illustration 14 g01212907
17. Install pins (37) into barrel (38).
Illustration 15 g01212906
18. Install bearing (36), retainer (35), and pistons (34).
6/11
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 16 g01212905
19. Install rotating group (32) and shim (33).
Note: Shim thickness was determined on Step 9.
Illustration 17 g01212904
20. Install bearing cone (31).
Illustration 18 g01212903
21. Install piston (30).
7/11
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 19 g01212902
22. Install spring (27), piston (29), and O-ring seal (28).
Illustration 20 g01213436
23. Install O-ring seals (24) and port plate (25).
Illustration 21 g01212900
8/11
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
24. Install head (23) and bolts (22).
Illustration 22 g01212898
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
25. Install spool (15), poppet (16), spring (17), spring (18), shim (19), O-ring seal (20), and
housing (21) into housing (2).
26. Install retainer (7), spring (8), retainer (9), spool (10), O-ring seal (12), backup ring (11), O-
ring seal (13), and cartridge (14).
27. Install screw (6) into housing (2).
9/11
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g01212897
28. Install coil (4) and nut (5).
Illustration 24 g01212896
29. Install O-ring seals (3).
Illustration 25 g01212895
30. Install controller (2) and bolts (1).
End By:
10/11
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 E...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. a. Install the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Hydraulic Fan)
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 17:38:47 UTC+0800 2020
11/11
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 E...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR PPN
Configuration: 336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02424411
Piston Pump (Hydraulic Fan) - Install
SMCS - 1387-012-QP; 5070-012-HFN
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01211400
1. Position piston pump (7) and install bolts (6).
2. Connect harness assembly (5).
3. Connect hose assemblies (3) and (4).
1/2
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01211399
4. Connect hose assembly (2).
Illustration 3 g01206719
5. Close door (1).
6. Fill the hydraulic system with oil. Refer to Operation and Maintenance Manual, "Refill
Capacities".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 17:39:43 UTC+0800 2020
2/2
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR PPN
Configuration: 336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415451
Piston Motor (Hydraulic Fan) - Remove
SMCS - 1386-011-QP; 5058-011-FM
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g01207415
1. Bend locking tabs (1) backward.
2. Remove bolts (2) and hub (3).
1/2
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g01207416
3. Use a suitable lifting device to position fan motor assembly (4) onto suitable cribbing. The
weight of fan motor assembly (4) is approximately 68 kg (150 lb).
Illustration 3 g01207418
4. Attach a suitable lifting device to piston motor (5). The weight of piston motor (5) is
approximately 23 kg (50 lb).
5. Remove bolts (6) and fan motor (5).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 17:40:40 UTC+0800 2020
2/2
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR PPN
Configuration: 336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415272
Piston Motor (Hydraulic Fan) - Disassemble
SMCS - 1386-015-QP; 5058-015-FM; 5058-015-HFN
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9152 Bearing Puller Gp 1
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Start By:
a. Remove the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Remove".
1/7
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g01207275
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove bolts (1) and head (2).
Illustration 2 g01207276
2. Remove O-ring seal (3), port plate (4), and bearing cup (5).
Illustration 3 g01207278
2/7
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove plug (6), sleeve (7), poppet (8), spring (9), poppet (10), and O-ring seal (11).
Illustration 4 g01207279
4. Remove bearing cone (12).
Illustration 5 g01207280
5. Remove shim (13) and rotating group (14).
3/7
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 9 g01207284
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Use Tooling (C) and Tooling (B) in order to remove retaining ring (19).
10. Remove shim (23), spring (22), and shim (21).
Illustration 10 g01207285
11. Remove swashplate (24) and shaft (25).
5/7
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 11 g01207287
12. Use Tooling (A) in order to remove bearing cone (26) from shaft (25).
Illustration 12 g01207286
13. Use Tooling (C) in order to remove retaining ring (27).
14. Remove lip seal (28).
Illustration 13 g01207288
15. Remove bearing cup (29).
6/7
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR PPN
Configuration: 336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415273
Piston Motor (Hydraulic Fan) - Assemble
SMCS - 1386-016-QP; 5058-016-FM; 5058-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Illustration 1 g01207288
1. Install bearing cup (29).
1/7
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 2 g01207286
2. Install lip seal (28).
3. Use Tooling (C) in order to install retaining ring (27).
Illustration 3 g01207624
4. Raise the temperature of bearing cone (26).
5. Install bearing cone (26) onto shaft (25).
Illustration 4 g01207285
6. Install shaft (25) and swashplate (24).
2/7
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 5 g01207283
Illustration 6 g01207284
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
7. Install shim (21), spring (22), and shim (23).
8. Use Tooling (C) and Tooling (B) in order to install retaining ring (19).
3/7
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 7 g01207282
9. Install pins (18).
Illustration 8 g01207281
10. Install bearing (17).
11. Install pistons (15) and retainer (16).
Illustration 9 g01207280
12. Install rotating group (14) and shim (13).
4/7
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 10 g01207279
13. Install bearing cone (12).
Illustration 11 g01207278
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install O-ring seal (11), poppet (10), spring (9), poppet (8), sleeve (7), and plug (6).
5/7
336D L & 336D LN Excavators PPN00001-UP (MACHINE) POWERED BY C9 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...