This document provides instructions to disassemble and assemble the travel motor on a 336F L and 336F LN excavator. The disassembly procedure involves removing 30 parts from the travel motor in 29 steps. The assembly procedure involves installing 35 parts into the travel motor in 10 steps, and notes that springs must be installed correctly and tools are needed to install seals and retainers safely.
Caterpillar cat 336 f l excavator (prefix wtz) service repair manual (wtz0000...fjsjekdmmeme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. The disassembly procedure involves 30 steps to remove components like springs, seals, plates, and housing pieces. The assembly procedure reverses the disassembly with 23 steps like installing seals, springs, pistons and housing components. Special tools are listed and safety notices are provided regarding spring forces and component alignment.
Caterpillar cat 336 f excavator (prefix nbl) service repair manual (nbl00001 ...fjsqazkekdmme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. It describes 30 steps to disassemble the travel motor, removing components like springs, seals, plates, and housing pieces. It then describes 31 steps to reassemble the travel motor, replacing components in the reverse order and noting specifics like torque settings and lubrication points. The overall document provides detailed instructions to take apart and rebuild the travel motor.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...cdsaas
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 e excavator (prefix spg) service repair manual (spg00001 ...cdsaas
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves removing 27 individual components from the motor housing, rotating group, and brake housing. The assembly process describes installing the components in reverse order and includes specifications for various parts. Proper lubrication and torque specifications are noted throughout.
Caterpillar cat 336 f l excavator (prefix kft) service repair manual (kft0000...fjsjekdmmeme
This document provides instructions for disassembling a 336F excavator travel motor. It lists 27 steps to completely disassemble the travel motor. The steps include removing the motor head assembly, springs, seals, plates, pistons, bearings, and other internal components. Precautions are provided to watch for spring forces and contain fluids during disassembly. Special tools are listed that are required to properly disassemble parts like retaining rings and pistons.
Caterpillar cat 336 f excavator (prefix lcl) service repair manual (lcl00001 ...fjsqazkekdmme
This document provides instructions to disassemble a 336F and 336F L excavator travel motor. It lists the required tools and describes 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal components. Marks should be made on components to ensure proper reassembly. Care is needed when removing parts to avoid damage and release of stored spring forces.
Caterpillar cat 336 e l excavator (prefix tmz) service repair manual (tmz0000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 336E LN excavator travel motor. The disassembly procedure involves removing 27 parts from the travel motor housing including the head, springs, brake piston, plates, and seals. The assembly procedure instructs installing these 27 parts in reverse order and provides notes to ensure proper installation of parts like pistons, seals, and bearing races. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, bearing puller, and Loctite.
Caterpillar cat 336 f excavator (prefix dsw) service repair manual (dsw00001 ...pfiskdmjekm
This document provides disassembly instructions for a 336F and 336F L excavator travel motor. It outlines 27 steps to fully disassemble the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, swashplate, and other internal components. Detailed illustrations are provided to identify each part and guide the disassembly process. Safety precautions are noted throughout to warn of potential spring forces or fluid hazards during disassembly.
Caterpillar cat 336 f l excavator (prefix wtz) service repair manual (wtz0000...fjsjekdmmeme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. The disassembly procedure involves 30 steps to remove components like springs, seals, plates, and housing pieces. The assembly procedure reverses the disassembly with 23 steps like installing seals, springs, pistons and housing components. Special tools are listed and safety notices are provided regarding spring forces and component alignment.
Caterpillar cat 336 f excavator (prefix nbl) service repair manual (nbl00001 ...fjsqazkekdmme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. It describes 30 steps to disassemble the travel motor, removing components like springs, seals, plates, and housing pieces. It then describes 31 steps to reassemble the travel motor, replacing components in the reverse order and noting specifics like torque settings and lubrication points. The overall document provides detailed instructions to take apart and rebuild the travel motor.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...cdsaas
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 e excavator (prefix spg) service repair manual (spg00001 ...cdsaas
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves removing 27 individual components from the motor housing, rotating group, and brake housing. The assembly process describes installing the components in reverse order and includes specifications for various parts. Proper lubrication and torque specifications are noted throughout.
Caterpillar cat 336 f l excavator (prefix kft) service repair manual (kft0000...fjsjekdmmeme
This document provides instructions for disassembling a 336F excavator travel motor. It lists 27 steps to completely disassemble the travel motor. The steps include removing the motor head assembly, springs, seals, plates, pistons, bearings, and other internal components. Precautions are provided to watch for spring forces and contain fluids during disassembly. Special tools are listed that are required to properly disassemble parts like retaining rings and pistons.
Caterpillar cat 336 f excavator (prefix lcl) service repair manual (lcl00001 ...fjsqazkekdmme
This document provides instructions to disassemble a 336F and 336F L excavator travel motor. It lists the required tools and describes 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal components. Marks should be made on components to ensure proper reassembly. Care is needed when removing parts to avoid damage and release of stored spring forces.
Caterpillar cat 336 e l excavator (prefix tmz) service repair manual (tmz0000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 336E LN excavator travel motor. The disassembly procedure involves removing 27 parts from the travel motor housing including the head, springs, brake piston, plates, and seals. The assembly procedure instructs installing these 27 parts in reverse order and provides notes to ensure proper installation of parts like pistons, seals, and bearing races. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, bearing puller, and Loctite.
Caterpillar cat 336 f excavator (prefix dsw) service repair manual (dsw00001 ...pfiskdmjekm
This document provides disassembly instructions for a 336F and 336F L excavator travel motor. It outlines 27 steps to fully disassemble the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, swashplate, and other internal components. Detailed illustrations are provided to identify each part and guide the disassembly process. Safety precautions are noted throughout to warn of potential spring forces or fluid hazards during disassembly.
Caterpillar cat 336 f ln excavator (prefix wtz) service repair manual (wtz000...fjsjekdmmeme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. It includes 30 steps for disassembly that remove components like caps, springs, valves, plugs, seals and assemblies. The assembly section has 17 steps that install components in the reverse order, taking care to lubricate seals and apply retaining compounds. Special safety notes warn of spring loaded parts and heavy components that require lifting equipment.
Caterpillar cat 336 f l excavator (prefix nbl) service repair manual (nbl0000...fjsqazkekdmme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. It describes 30 steps to disassemble the travel motor, removing components like springs, seals, plates, and housing pieces. It then describes 31 steps to reassemble the travel motor, replacing components in the reverse order and noting specifics like torque settings and lubrication points. The overall document provides detailed instructions to take apart and rebuild the travel motor.
Caterpillar Cat 336F and 336F L Excavator (Prefix NBL) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety cautions are provided throughout for parts under spring tension.
Caterpillar cat 336 f l excavator (prefix nbl) service repair manual (nbl0000...ujdkkdkdmm
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety cautions are provided throughout for components under spring pressure.
Caterpillar cat 336 f excavator (prefix nbl) service repair manual (nbl00001 ...wedsrffcdgdv
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety warnings are provided throughout for components under spring pressure.
Caterpillar cat 336 f l excavator (prefix nbl) service repair manual (nbl0000...wedsrffcdgdv
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety cautions are provided throughout for parts under spring tension.
This document is the service manual for the Clark SM-560 lift truck. It contains sections on safety, maintenance procedures, inspections, repairs, and specifications. The manual emphasizes the importance of regularly maintaining the lift truck according to the manufacturer's recommendations to ensure safe operation and maximum performance of the vehicle.
Clark tmg 13 20 x forklift service repair manualdidkkmmdm
This document provides a summary of safe maintenance practices for industrial trucks. It discusses safety signs and messages used in service manuals. Proper ventilation, fire safety, and authorized personnel are important. Before working on a truck, raise the wheels, disconnect the battery, and check for fuel and electrical hazards. Replacements parts must meet manufacturer standards. Modifications require approval. Overall, maintenance should follow manufacturer procedures to ensure safety.
Clark tmg 12 25 forklift service repair manualdidkkmmdm
This document is a service manual for Clark forklifts that contains information on safety, maintenance, repairs, specifications and other technical details. It includes sections on topics such as batteries, motors, brakes, hydraulics, steering and other systems. The manual uses a standardized grouping and numbering system to organize content and make specific information easy to locate. Safety precautions and proper maintenance are emphasized throughout.
This document provides information about periodic maintenance and planned maintenance for HWX/PWX trucks, including:
1. Maintenance schedules and intervals that should be followed based on operating conditions.
2. Details of a planned maintenance program that includes inspections, tests, and recording truck conditions on a checklist.
3. A sample planned maintenance report form to document inspections and needed repairs.
This service manual provides maintenance and repair information for PWT tow tractors and PWC center controlled pallet trucks, including specifications for electrical systems, dimensions, capacities, component details, and a list of required tools. Standard specifications are provided for models of both the PWT and PWC, including motor type, gear ratios, speeds, dimensions, weight, battery options, tire types, and performance capacities. The document also includes sections on record keeping, torque charts, and maintenance recommendations to assist technicians in properly servicing the equipment.
Clark pwd 36 forklift service repair manualdidkkmmdm
This document provides instructions for performing planned maintenance on Clark industrial trucks. It outlines visual inspections, operational tests, and checks of components like the battery, tires, frame, control handle, steering, brakes, travel speeds, and coast control. Technicians are instructed to note any issues found on a check sheet using a coding system to indicate the urgency of repairs needed.
Clark pwd 30 forklift service repair manualdidkkmmdm
This document provides instructions and safety precautions for performing planned maintenance on Clark industrial trucks. It outlines inspection procedures for components like the battery, plug, and cover. Technicians should note any issues found on a check sheet using codes to indicate the urgency of repairs needed, from minor adjustments to replacements requiring a shop visit. Visual inspections and keeping electrical components jewelry-free are emphasized for safety.
Clark pwd 25 forklift service repair manualdidkkmmdm
This document provides instructions and safety precautions for performing planned maintenance on Clark industrial trucks. It outlines inspection procedures for components like the battery, plug, and cover. Technicians should carefully inspect all systems and note any issues found on the maintenance check sheet using a coding system to indicate the urgency of repairs needed. Safety is emphasized throughout, including wearing protective equipment and disabling trucks before working on electrical components.
The document is a service manual that provides general information and specifications for Clark PWT tow tractors and PWC center controlled pallet trucks, including details on their electrical systems, dimensions, capacities, component specifications, and maintenance requirements. It also includes a table of contents listing the sections covered in the manual, and notes that the power sections of the PWT and PWC are the same despite their different applications.
This document provides specifications, maintenance schedules, and repair procedures for Clark PT-5, PT-7, PTT-5, and PTT-7 trucks. It includes sections on specifications, planned maintenance, adjustments, electrical systems, transmissions, and safety practices. The planned maintenance section outlines inspection and lubrication intervals, with tasks grouped into daily, monthly, quarterly, biannual, and annual maintenance checks.
This document provides specifications, maintenance schedules, adjustment procedures, and safety information for Clark PT-5, PT-7, PTT-5, and PTT-7 trucks. It outlines an essential planned maintenance program to keep the trucks in safe operating condition, including inspections, operational checks, cleaning, lubrication, and adjustments. The document emphasizes following maintenance procedures and safety practices to avoid hazards that could result in injury or death. It also provides specifications for electrical systems, fluids, tires, and other components.
This document provides specifications, maintenance schedules, adjustment procedures, and safety information for Clark PT-5, PT-7, PTT-5, and PTT-7 trucks. It outlines an essential planned maintenance program to keep the trucks safely operating, including inspections, operational checks, cleaning, lubrication, and adjustments. The document emphasizes safety practices for maintenance, such as raising the wheels, disconnecting power, and using blocks or stands before working under a truck.
This document provides specifications, maintenance schedules, adjustment procedures, and safety information for Clark PT-5, PT-7, PTT-5, and PTT-7 trucks. It outlines an essential planned maintenance program to keep the trucks in safe operating condition, including inspections, operational checks, cleaning, lubrication, and adjustments. Safety practices for maintenance are also listed, such as disconnecting power sources before working on electrical systems, and using lifting equipment rated for heavy components.
Caterpillar cat 336 f ln excavator (prefix zbj) service repair manual (zbj000...didkkmmdm
This document provides instructions for assembling and disassembling a travel motor on Caterpillar 336F L and 336F LN excavators powered by a C9.3 engine. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. Removal instructions are also provided in 13 steps, including draining fluids and marking components for proper reinstallation.
Caterpillar cat 336 f ln excavator (prefix wtz) service repair manual (wtz000...didkkmmdm
This document provides instructions to disassemble and assemble the travel motor on a 336F L and 336F LN excavator. The disassembly procedure involves removing 30 parts from the travel motor in 29 steps. The assembly procedure involves installing 35 parts into the travel motor in 10 steps, and notes that springs must be installed correctly and tools are needed to install seals and retainers safely.
More Related Content
Similar to Caterpillar cat 336 f l excavator (prefix wtz) service repair manual (wtz00001 and up)
Caterpillar cat 336 f ln excavator (prefix wtz) service repair manual (wtz000...fjsjekdmmeme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. It includes 30 steps for disassembly that remove components like caps, springs, valves, plugs, seals and assemblies. The assembly section has 17 steps that install components in the reverse order, taking care to lubricate seals and apply retaining compounds. Special safety notes warn of spring loaded parts and heavy components that require lifting equipment.
Caterpillar cat 336 f l excavator (prefix nbl) service repair manual (nbl0000...fjsqazkekdmme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. It describes 30 steps to disassemble the travel motor, removing components like springs, seals, plates, and housing pieces. It then describes 31 steps to reassemble the travel motor, replacing components in the reverse order and noting specifics like torque settings and lubrication points. The overall document provides detailed instructions to take apart and rebuild the travel motor.
Caterpillar Cat 336F and 336F L Excavator (Prefix NBL) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety cautions are provided throughout for parts under spring tension.
Caterpillar cat 336 f l excavator (prefix nbl) service repair manual (nbl0000...ujdkkdkdmm
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety cautions are provided throughout for components under spring pressure.
Caterpillar cat 336 f excavator (prefix nbl) service repair manual (nbl00001 ...wedsrffcdgdv
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety warnings are provided throughout for components under spring pressure.
Caterpillar cat 336 f l excavator (prefix nbl) service repair manual (nbl0000...wedsrffcdgdv
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety cautions are provided throughout for parts under spring tension.
Similar to Caterpillar cat 336 f l excavator (prefix wtz) service repair manual (wtz00001 and up) (6)
This document is the service manual for the Clark SM-560 lift truck. It contains sections on safety, maintenance procedures, inspections, repairs, and specifications. The manual emphasizes the importance of regularly maintaining the lift truck according to the manufacturer's recommendations to ensure safe operation and maximum performance of the vehicle.
Clark tmg 13 20 x forklift service repair manualdidkkmmdm
This document provides a summary of safe maintenance practices for industrial trucks. It discusses safety signs and messages used in service manuals. Proper ventilation, fire safety, and authorized personnel are important. Before working on a truck, raise the wheels, disconnect the battery, and check for fuel and electrical hazards. Replacements parts must meet manufacturer standards. Modifications require approval. Overall, maintenance should follow manufacturer procedures to ensure safety.
Clark tmg 12 25 forklift service repair manualdidkkmmdm
This document is a service manual for Clark forklifts that contains information on safety, maintenance, repairs, specifications and other technical details. It includes sections on topics such as batteries, motors, brakes, hydraulics, steering and other systems. The manual uses a standardized grouping and numbering system to organize content and make specific information easy to locate. Safety precautions and proper maintenance are emphasized throughout.
This document provides information about periodic maintenance and planned maintenance for HWX/PWX trucks, including:
1. Maintenance schedules and intervals that should be followed based on operating conditions.
2. Details of a planned maintenance program that includes inspections, tests, and recording truck conditions on a checklist.
3. A sample planned maintenance report form to document inspections and needed repairs.
This service manual provides maintenance and repair information for PWT tow tractors and PWC center controlled pallet trucks, including specifications for electrical systems, dimensions, capacities, component details, and a list of required tools. Standard specifications are provided for models of both the PWT and PWC, including motor type, gear ratios, speeds, dimensions, weight, battery options, tire types, and performance capacities. The document also includes sections on record keeping, torque charts, and maintenance recommendations to assist technicians in properly servicing the equipment.
Clark pwd 36 forklift service repair manualdidkkmmdm
This document provides instructions for performing planned maintenance on Clark industrial trucks. It outlines visual inspections, operational tests, and checks of components like the battery, tires, frame, control handle, steering, brakes, travel speeds, and coast control. Technicians are instructed to note any issues found on a check sheet using a coding system to indicate the urgency of repairs needed.
Clark pwd 30 forklift service repair manualdidkkmmdm
This document provides instructions and safety precautions for performing planned maintenance on Clark industrial trucks. It outlines inspection procedures for components like the battery, plug, and cover. Technicians should note any issues found on a check sheet using codes to indicate the urgency of repairs needed, from minor adjustments to replacements requiring a shop visit. Visual inspections and keeping electrical components jewelry-free are emphasized for safety.
Clark pwd 25 forklift service repair manualdidkkmmdm
This document provides instructions and safety precautions for performing planned maintenance on Clark industrial trucks. It outlines inspection procedures for components like the battery, plug, and cover. Technicians should carefully inspect all systems and note any issues found on the maintenance check sheet using a coding system to indicate the urgency of repairs needed. Safety is emphasized throughout, including wearing protective equipment and disabling trucks before working on electrical components.
The document is a service manual that provides general information and specifications for Clark PWT tow tractors and PWC center controlled pallet trucks, including details on their electrical systems, dimensions, capacities, component specifications, and maintenance requirements. It also includes a table of contents listing the sections covered in the manual, and notes that the power sections of the PWT and PWC are the same despite their different applications.
This document provides specifications, maintenance schedules, and repair procedures for Clark PT-5, PT-7, PTT-5, and PTT-7 trucks. It includes sections on specifications, planned maintenance, adjustments, electrical systems, transmissions, and safety practices. The planned maintenance section outlines inspection and lubrication intervals, with tasks grouped into daily, monthly, quarterly, biannual, and annual maintenance checks.
This document provides specifications, maintenance schedules, adjustment procedures, and safety information for Clark PT-5, PT-7, PTT-5, and PTT-7 trucks. It outlines an essential planned maintenance program to keep the trucks in safe operating condition, including inspections, operational checks, cleaning, lubrication, and adjustments. The document emphasizes following maintenance procedures and safety practices to avoid hazards that could result in injury or death. It also provides specifications for electrical systems, fluids, tires, and other components.
This document provides specifications, maintenance schedules, adjustment procedures, and safety information for Clark PT-5, PT-7, PTT-5, and PTT-7 trucks. It outlines an essential planned maintenance program to keep the trucks safely operating, including inspections, operational checks, cleaning, lubrication, and adjustments. The document emphasizes safety practices for maintenance, such as raising the wheels, disconnecting power, and using blocks or stands before working under a truck.
This document provides specifications, maintenance schedules, adjustment procedures, and safety information for Clark PT-5, PT-7, PTT-5, and PTT-7 trucks. It outlines an essential planned maintenance program to keep the trucks in safe operating condition, including inspections, operational checks, cleaning, lubrication, and adjustments. Safety practices for maintenance are also listed, such as disconnecting power sources before working on electrical systems, and using lifting equipment rated for heavy components.
Caterpillar cat 336 f ln excavator (prefix zbj) service repair manual (zbj000...didkkmmdm
This document provides instructions for assembling and disassembling a travel motor on Caterpillar 336F L and 336F LN excavators powered by a C9.3 engine. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. Removal instructions are also provided in 13 steps, including draining fluids and marking components for proper reinstallation.
Caterpillar cat 336 f ln excavator (prefix wtz) service repair manual (wtz000...didkkmmdm
This document provides instructions to disassemble and assemble the travel motor on a 336F L and 336F LN excavator. The disassembly procedure involves removing 30 parts from the travel motor in 29 steps. The assembly procedure involves installing 35 parts into the travel motor in 10 steps, and notes that springs must be installed correctly and tools are needed to install seals and retainers safely.
Caterpillar cat 336 f ln excavator (prefix rbc) service repair manual (rbc000...didkkmmdm
This document provides instructions for disassembling the travel motor on a 336F LN excavator. It describes 27 steps to completely disassemble the travel motor, removing components like the motor head assembly, various plugs, seals, springs, relief valves, and more. Detailed illustrations accompany each step to show how to properly remove and disassemble the parts. Safety notices are included throughout to warn of potential hazards like released spring forces during disassembly.
Caterpillar cat 336 f ln excavator (prefix nbs) service repair manual (nbs000...didkkmmdm
This document provides instructions for disassembling the travel motor on a 336F L & 336F LN Excavator. It outlines 27 steps to remove parts like the motor head assembly, springs, seals, relief valves, plugs and spools. Various tools are required including a driver group, retaining ring pliers, bearing puller group and lifting eye assembly to safely remove parts and release spring forces during disassembly.
Caterpillar cat 336 f ln excavator (prefix kft) service repair manual (kft000...didkkmmdm
The document provides instructions for disassembling a 336F excavator travel motor. It describes 27 steps to remove components such as the motor head assembly, springs, seals, relief valves, plugs and bolts. Various tools are required including a driver group, retaining ring pliers, bearing puller group and eyebolt for lifting components. Safety precautions are provided to release spring forces and contain fluids.
Caterpillar cat 336 f ln excavator (prefix dkf) service repair manual (dkf000...didkkmmdm
This document provides instructions for disassembling and assembling the travel motor on Caterpillar 336F L and 336F LN excavator models. It outlines 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. It then describes 17 steps to reassemble the travel motor by installing these same components in the reverse order. Tools required are also listed.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L EXCAVATOR WTZ
Configuration: 336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07195340
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C
6V-5215 M8 X 1.25 X 16 MM Bolt 2
9M-1974 M8 Hard Washer 2
D 1P-0510 Driver Gp 1
Start By:
a. Remove travel motor.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06249277
1. Fasten travel motor (1) in a vertical position on Tooling (A). The weight of travel motor (1)
is approximately 82 kg (180 lb).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2. Remove bolts (2) and cap (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
2/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 2 g06249309
Illustration 3 g06249323
Illustration 4 g06249325
3. Remove bolts (4) and cap (5).
4. Remove spring (6), spring (9), spool assembly (8), and spring seats (7).
3/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g06249329
5. Remove plug (11), relief valve (10), and the O-ring seals.
Illustration 6 g06249334
6. Remove plug (13), relief valve (12), and the O-ring seals.
Illustration 7 g06249337
7. Remove plug (14), and the O-ring seal.
4/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g06249341
Illustration 9 g06249344
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove plug (15), spool assembly (16), spring (17), and the O-ring seals.
5/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g06249348
9. Remove plugs (18) and the O-ring seals.
Illustration 11 g06249351
10. Remove bolts (19).
Illustration 12 g06249354
11. Attach Tooling (B) and a suitable lifting device to motor head assembly (20). The weight of
motor head assembly (20) is approximately 27 kg (60 lb). Remove motor head assembly
(20).
6/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g06250338
12. Remove the ball bearing that is located on the bottom side of motor head assembly (20).
Illustration 14 g06249364
Port plate (25) may still be adhered to the bottom of motor head assembly (20).
13. Remove O-ring seals (21), O-ring seal (22), springs (23), springs (24), and port plate (25).
Note: Note the location of springs (23). They must be installed in the same location during
the assembly procedure.
Illustration 15 g06249511
7/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 14. Insert Tooling (C) into piston assembly (26). Use a suitable prying device and Tooling (C)
to remove piston assembly (26).
Illustration 16 g06250418
15. Remove O-ring seal (27) and O-ring seal (28).
Illustration 17 g06249522
16. Use suitable prying devices to remove guide assembly (29).
Illustration 18 g06249535
17. Remove O-ring seal (30).
8/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 19 g06249539
Illustration 20 g06249544
18. Remove separator plates (31) and friction plates (32). Note the alternating order of separator
plates (31) and friction plates (32) for assembly purposes.
Illustration 21 g06249564
19. Remove barrel assembly (33).
Note: Do not allow the components of barrel assembly (33) to come apart while you
remove barrel assembly (33). The components of barrel assembly (33) must be reinstalled
into the original positions.
9/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 22 g06249598
Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
20. Remove piston assemblies (34) and retainer (35).
Illustration 23 g06249609
21. Remove hold down ball (36).
Illustration 24 g06249621
10/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 22. Remove dowel pins (37).
Illustration 25 g06249657
23. Put location marks on swashplate (38) for assembly purposes. Remove swashplate (38).
Illustration 26 g06249682
24. Remove pistons (39) and the balls.
Illustration 27 g06249751
25. Remove springs (40).
11/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 28 g06249755
Illustration 29 g06249758
26. Use a suitable press and Tooling (D) to remove snap ring (41), spacers (42), and spring (43).
12/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 30 g06249760
27. Use a soft faced hammer to remove shaft assembly (44). Remove shaft assembly (44) in the
direction that is indicated by the arrow.
28. Remove O-ring seal (45).
Illustration 31 g06249762
29. Remove lip seal (46).
Illustration 32 g06249763
30. Use a suitable press to push shaft (47) out of bearing (48).
13/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L EXCAVATOR WTZ
Configuration: 336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15).
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15).
Note: Bearing race (18) must contact retaining ring (17).
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16).
17. Place the pump housing into Tooling (A).
6/10
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 14 g02107957
18. Use Tooling (C) to install rotating assembly (16) into the housing.
Illustration 15 g00887501
Illustration 16 g02107975
19. The notches in cam plate (20) must align with keys (26). The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
7/10
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8).
24. Install brake piston (8) into the housing so that the cast mark on brake piston (8) is aligned
with the brake supply passage in the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level to
prevent damage to the O-ring seals.
8/10
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6).
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5).
Illustration 22 g00887295
9/10
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jun 16 16:25:52 UTC+0800 2020
10/10
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L EXCAVATOR WTZ
Configuration: 336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07197988
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C 6V-2055 Grease -
D 1P-0510 Driver Gp 1
Illustration 1 g06250080
1. Use a suitable press to press bearing (48) onto shaft (47).
1/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 2 g06249762
Illustration 3 g06250732
Lip seal orientation.
2. Install lip seal (46).
Illustration 4 g06250082
3. Install O-ring seal (45).
4. Use a soft faced hammer to install shaft assembly (44). Install shaft assembly (44) in the
direction that is indicated by the arrow.
2/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
Illustration 5 g06249755
Illustration 6 g06249758
5. Use a suitable press and Tooling (D) to install spacers (42), spring (43), and snap ring (41).
3/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
29. Illustration 7 g06249751
6. Install springs (40) and the balls.
Illustration 8 g06249682
7. Install pistons (39).
Illustration 9 g06249657
8. Install swashplate (38).
4/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 13 g06250125
Typical example.
Illustration 14 g06249564
12. Wrap a piece of nylon string around the piston assemblies as shown. Install barrel assembly
(33). Use the nylon string to hold the assembly together during installation. Remove the
nylon string.
Illustration 15 g06249544
6/14
336F L & 336F LN Excavators WTZ00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...