The document provides instructions for disassembling a 336F excavator travel motor. It describes 27 steps to remove components such as the motor head assembly, springs, seals, relief valves, plugs and bolts. Various tools are required including a driver group, retaining ring pliers, bearing puller group and eyebolt for lifting components. Safety precautions are provided to release spring forces and contain fluids.
Caterpillar cat 336 f l excavator (prefix kft) service repair manual (kft0000...fjsjekdmmeme
This document provides instructions for disassembling a 336F excavator travel motor. It lists 27 steps to completely disassemble the travel motor. The steps include removing the motor head assembly, springs, seals, plates, pistons, bearings, and other internal components. Precautions are provided to watch for spring forces and contain fluids during disassembly. Special tools are listed that are required to properly disassemble parts like retaining rings and pistons.
Caterpillar cat 336 f l excavator (prefix nbs) service repair manual (nbs0000...fjsjekdmmeme
This document provides disassembly instructions for a 336F excavator travel motor. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Various tools are required to remove parts and release spring forces safely. Detailed illustrations accompany each step to show how to disassemble the individual components of the travel motor.
Caterpillar cat 336 f l excavator (prefix rbc) service repair manual (rbc0000...fjsjekdmmeme
This document provides instructions for disassembling the travel motor on 336F L and 336F LN excavator models. It lists the required tools and presents 27 steps to remove components such as the motor head assembly, springs, seals, relief valves, plugs and port plate. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 336 f excavator (prefix wcf) service repair manual (wcf00001 ...fjkskedmme
The document provides disassembly instructions for a 336F excavator travel motor over 27 steps. It details removing components like the motor head assembly, piston assemblies, barrel assembly, swashplate, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and various bolts, pins and seals. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 336 f excavator (prefix yfd) service repair manual (yfd00001 ...fjsqazkekdmme
This document provides disassembly instructions for a 336F excavator travel motor over 27 steps. It details removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Personal protective equipment is recommended as springs store potential energy. Reinstallation marks are advised to ensure correct reassembly.
Caterpillar cat 336 f ln excavator (prefix kft) service repair manual (kft000...fjsjekdmmeme
This document provides disassembly instructions for a 336F excavator travel motor. It lists 27 steps to fully disassemble the travel motor, including removing the head, brake components, rotating assembly, piston assemblies, seals, and other internal parts. Precautions are provided to safely release spring forces and contain fluids. Required tools include various bolts, pins, pullers and stands to dismantle the motor in a vertical position. Detailed illustrations accompany each step.
Caterpillar cat 336 f l excavator (prefix rbc) service repair manual (rbc0000...didkkmmdm
This document provides instructions for disassembling the travel motor on a 336F LN excavator. It describes 27 steps to completely disassemble the travel motor, removing components like the motor head assembly, various plugs, seals, springs, relief valves and more. Detailed illustrations accompany each step to show how to properly remove each part. Safety precautions are provided throughout to warn of potential hazards like released spring forces during disassembly.
Caterpillar cat 336 f l excavator (prefix rbc) service repair manual (rbc0000...fjsjekkdmnem
The document provides instructions for disassembling the travel motor on a 336F LN excavator. It describes 27 steps to remove parts like the motor head assembly, springs, seals, relief valves, plugs and spools. Tools required include a transmission repair stand, lifting eye assembly, driver group and various bolts, plugs and seals. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 336 f l excavator (prefix kft) service repair manual (kft0000...fjsjekdmmeme
This document provides instructions for disassembling a 336F excavator travel motor. It lists 27 steps to completely disassemble the travel motor. The steps include removing the motor head assembly, springs, seals, plates, pistons, bearings, and other internal components. Precautions are provided to watch for spring forces and contain fluids during disassembly. Special tools are listed that are required to properly disassemble parts like retaining rings and pistons.
Caterpillar cat 336 f l excavator (prefix nbs) service repair manual (nbs0000...fjsjekdmmeme
This document provides disassembly instructions for a 336F excavator travel motor. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Various tools are required to remove parts and release spring forces safely. Detailed illustrations accompany each step to show how to disassemble the individual components of the travel motor.
Caterpillar cat 336 f l excavator (prefix rbc) service repair manual (rbc0000...fjsjekdmmeme
This document provides instructions for disassembling the travel motor on 336F L and 336F LN excavator models. It lists the required tools and presents 27 steps to remove components such as the motor head assembly, springs, seals, relief valves, plugs and port plate. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 336 f excavator (prefix wcf) service repair manual (wcf00001 ...fjkskedmme
The document provides disassembly instructions for a 336F excavator travel motor over 27 steps. It details removing components like the motor head assembly, piston assemblies, barrel assembly, swashplate, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and various bolts, pins and seals. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 336 f excavator (prefix yfd) service repair manual (yfd00001 ...fjsqazkekdmme
This document provides disassembly instructions for a 336F excavator travel motor over 27 steps. It details removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Personal protective equipment is recommended as springs store potential energy. Reinstallation marks are advised to ensure correct reassembly.
Caterpillar cat 336 f ln excavator (prefix kft) service repair manual (kft000...fjsjekdmmeme
This document provides disassembly instructions for a 336F excavator travel motor. It lists 27 steps to fully disassemble the travel motor, including removing the head, brake components, rotating assembly, piston assemblies, seals, and other internal parts. Precautions are provided to safely release spring forces and contain fluids. Required tools include various bolts, pins, pullers and stands to dismantle the motor in a vertical position. Detailed illustrations accompany each step.
Caterpillar cat 336 f l excavator (prefix rbc) service repair manual (rbc0000...didkkmmdm
This document provides instructions for disassembling the travel motor on a 336F LN excavator. It describes 27 steps to completely disassemble the travel motor, removing components like the motor head assembly, various plugs, seals, springs, relief valves and more. Detailed illustrations accompany each step to show how to properly remove each part. Safety precautions are provided throughout to warn of potential hazards like released spring forces during disassembly.
Caterpillar cat 336 f l excavator (prefix rbc) service repair manual (rbc0000...fjsjekkdmnem
The document provides instructions for disassembling the travel motor on a 336F LN excavator. It describes 27 steps to remove parts like the motor head assembly, springs, seals, relief valves, plugs and spools. Tools required include a transmission repair stand, lifting eye assembly, driver group and various bolts, plugs and seals. Safety precautions are provided to release spring forces and contain fluids during disassembly.
The document is a parts catalog for a Massey Ferguson TH.8043 130 ST4A tractor. It contains 14 sections that list parts for different systems of the tractor, including the engine and fuel system, frame and suspension, drive train, hydraulics, electrical system, and others. Each section contains multiple pages listing the individual parts, part numbers, quantities, and descriptions for that system. The parts catalog provides extensive detail on replacement parts for repair and maintenance of the Massey Ferguson tractor.
Massey ferguson th.6030 st3 a telescopic handler (b3gd14000 999 b3ge14000-99...fjsjekkdmnem
This document is a table of contents and sections for repair and maintenance of a Massey Ferguson TH.6030 ST3A telescopic handler. It outlines 14 main systems of the vehicle in individual sections, including the engine and fuel system, frame and suspension, steering, brakes, hydraulics, electrical system, and others. Each section includes item numbers, part numbers, quantities and descriptions of components for that system.
This document contains a table of contents and sections for repair and maintenance of a Massey Ferguson MF 9305 ST3A telescopic handler, including its engine, fuel and exhaust systems, frame, steering, drivetrain, brakes, hydraulics, electrical systems, cab, chassis, decals, wheels, articulating arm, hitch, hydrostatic system, and attachments. The sections provide part numbers, quantities, descriptions and other specifications for components.
This document provides parts information for Massey Ferguson MF 8925/8926 telescopic handlers, including diagrams labeling parts and their corresponding part numbers. It contains detailed lists of parts for various systems of the vehicle like the frame, counterweights, fuel system, engine cover, engine support, and cab. Each part is listed with its number, quantity used, description, and any additional comments. The diagrams provide visual context to identify the location and purpose of each listed part.
Massey ferguson mf 6690 combine hybrid class 5 tier3 parts catalogue manualfjsjekkdmnem
This document provides specifications for parts related to the cylinder block component of a Massey Ferguson MF 6690 combine engine. It contains 40 numbered items listing part numbers, quantities, and brief descriptions for the cylinder block and related parts, including the cylinder block itself, camshaft bearing bushes, cylinder liners, piston cooling jets, plugs, seals, and other components.
This document provides the assembly procedure for an M318 excavator transmission. It lists over 30 detailed steps and requires various specialty tools. The procedure involves assembling internal gears, installing seals and bearings, and setting precise clearances. Cleanliness is critical and all parts must be cleaned before assembly.
Massey ferguson mf 5690 combine hybrid class 4 tier3 parts catalogue manualfjsjekkdmnem
This document provides the table of contents and specifications for the engine, fuel, exhaust and cooling systems of a Massey Ferguson MF 5690 COMBINE HYBRID CLASS 4 - TIER3. It includes over 40 pages detailing over 1000 individual parts that make up these core systems, with images and descriptions for each part listed. The systems covered include the engine, power take-off, cooling radiator, drains, rotary screen and accessories like the air cleaner and ladder.
Massey ferguson mf 4690 combine hybrid class 4 tier3 parts catalogue manualfjsjekkdmnem
This document provides a parts list and technical specifications for the cylinder block of a Massey Ferguson MF 4690 COMBINE HYBRID CLASS 4 - TIER3 engine. It lists 40 parts that make up the cylinder block, including the cylinder block itself, camshaft bearing bushes, cylinder liners, plugs, seals, and other components. Each part is identified by part number and quantity used.
This document provides disassembly instructions for the final drive carriers, hubs, and brakes of the rear and front axles of an M318 Excavator. It outlines 32 steps to disassemble the rear axle components which include removing drain plugs, planetary carriers, gears, discs, seals, and other parts. It then provides 9 steps to disassemble the front axle planetary carrier. Required tools are listed. Safety notices are also provided.
This document contains a table of contents and sections for a service manual for a Massey Ferguson 9545/9565 combine. The table of contents lists 21 sections related to different systems of the combine, including the engine and fuel system, drive system, axles, frame and more. One section summarized here is the exhaust installation section, which includes a diagram and lists of parts related to the exhaust system, such as exhaust pipes, clamps, and shields.
Kubota mx5100 h tractor parts catalogue manualfjsjekkdmnem
This parts book provides information on parts for an engine. It lists part numbers, names, quantities, interchangeability, serial number ranges and other details. Notes explain country codes that may be included and differences in other regions. The document is intended to allow identification of correct replacement parts by part number and serial number range.
Clark npr 20 forklift service repair manualfjsjekkdmnem
This document is the service manual for Clark NPR-345 trucks. It contains safety cautions and detailed instructions for maintenance, repair, and overhaul of systems including electrical, hydraulic, brakes, steering, and other components. The manual is copyrighted and intended only for Clark dealers. It includes a table of contents listing the sections and their page numbers, along with pictorial indexes to identify components.
This document provides assembly instructions for a rear differential in 3 steps or less:
1. Determine the correct shim thickness for the inner pinion bearing using a series of measurement calculations.
2. Adjust the rolling torque of the pinion shaft by changing the shim thickness until it measures within specifications.
3. Assemble the remaining differential components like the ring gear, case halves, and differential gears.
Clark npr 17 forklift service repair manualfjsjekkdmnem
This document is the service manual for Clark NPR-345 trucks. It contains safety cautions and detailed instructions for maintenance, repair, and overhaul of systems including electrical, hydraulic, brakes, steering, and other components. The manual is copyrighted and intended only for Clark dealers. It includes a table of contents that lists all sections by group number, section number, and page number for easy reference to specific repair procedures. Pictorial indexes provide illustrations of components.
Caterpillar cat m320 f wheeled excavator (prefix fb2) service repair manual (...fjsjekkdmnem
This document provides assembly instructions for a piston pump used in a wheeled excavator model M320F. It consists of 50 steps to assemble the various components of the pump in the correct order. The components include springs, retainers, seals, valves, plates, bushings, shafts, and other parts. Precautions are provided for parts that are spring loaded to prevent injury during assembly.
Caterpillar cat m320 f wheeled excavator (prefix f2w) service repair manual (...fjsjekkdmnem
The document provides instructions for disassembling and assembling the rear axle of a M320F Wheeled Excavator. It lists the required tools and gives step-by-step instructions for removing components such as the carrier housing, planetary gears, brake discs, and hub. Reassembly instructions are also provided, describing how to install components like the thrust washer, carrier gear, and retaining rings. The purpose is to repair or replace parts in the rear axle transmission.
This document provides instructions for removing a crankshaft from a Caterpillar 3116 engine. The steps include:
1. Removing the cylinder head, crankshaft rear seal carrier, and front gear group.
2. Removing the crankshaft main bearing caps and bearings.
3. Using a bearing removal tool to pull the crankshaft from the engine block.
John deere 1565 front mower service repair manualfjsjekkdmnem
This technical manual provides service information for John Deere front mowers models 1420, 1435, 1445, 1545, and 1565. The manual is organized into specific sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, tests and adjustments, repair, and safety precautions. Technicians are advised to follow all safety procedures when servicing equipment to avoid injury from hazards like high pressure fluids, moving parts, hot surfaces, and heavy components.
John deere 1545 front mower service repair manualfjsjekkdmnem
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides procedures to check each component and make any necessary repairs or adjustments.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
The document is a parts catalog for a Massey Ferguson TH.8043 130 ST4A tractor. It contains 14 sections that list parts for different systems of the tractor, including the engine and fuel system, frame and suspension, drive train, hydraulics, electrical system, and others. Each section contains multiple pages listing the individual parts, part numbers, quantities, and descriptions for that system. The parts catalog provides extensive detail on replacement parts for repair and maintenance of the Massey Ferguson tractor.
Massey ferguson th.6030 st3 a telescopic handler (b3gd14000 999 b3ge14000-99...fjsjekkdmnem
This document is a table of contents and sections for repair and maintenance of a Massey Ferguson TH.6030 ST3A telescopic handler. It outlines 14 main systems of the vehicle in individual sections, including the engine and fuel system, frame and suspension, steering, brakes, hydraulics, electrical system, and others. Each section includes item numbers, part numbers, quantities and descriptions of components for that system.
This document contains a table of contents and sections for repair and maintenance of a Massey Ferguson MF 9305 ST3A telescopic handler, including its engine, fuel and exhaust systems, frame, steering, drivetrain, brakes, hydraulics, electrical systems, cab, chassis, decals, wheels, articulating arm, hitch, hydrostatic system, and attachments. The sections provide part numbers, quantities, descriptions and other specifications for components.
This document provides parts information for Massey Ferguson MF 8925/8926 telescopic handlers, including diagrams labeling parts and their corresponding part numbers. It contains detailed lists of parts for various systems of the vehicle like the frame, counterweights, fuel system, engine cover, engine support, and cab. Each part is listed with its number, quantity used, description, and any additional comments. The diagrams provide visual context to identify the location and purpose of each listed part.
Massey ferguson mf 6690 combine hybrid class 5 tier3 parts catalogue manualfjsjekkdmnem
This document provides specifications for parts related to the cylinder block component of a Massey Ferguson MF 6690 combine engine. It contains 40 numbered items listing part numbers, quantities, and brief descriptions for the cylinder block and related parts, including the cylinder block itself, camshaft bearing bushes, cylinder liners, piston cooling jets, plugs, seals, and other components.
This document provides the assembly procedure for an M318 excavator transmission. It lists over 30 detailed steps and requires various specialty tools. The procedure involves assembling internal gears, installing seals and bearings, and setting precise clearances. Cleanliness is critical and all parts must be cleaned before assembly.
Massey ferguson mf 5690 combine hybrid class 4 tier3 parts catalogue manualfjsjekkdmnem
This document provides the table of contents and specifications for the engine, fuel, exhaust and cooling systems of a Massey Ferguson MF 5690 COMBINE HYBRID CLASS 4 - TIER3. It includes over 40 pages detailing over 1000 individual parts that make up these core systems, with images and descriptions for each part listed. The systems covered include the engine, power take-off, cooling radiator, drains, rotary screen and accessories like the air cleaner and ladder.
Massey ferguson mf 4690 combine hybrid class 4 tier3 parts catalogue manualfjsjekkdmnem
This document provides a parts list and technical specifications for the cylinder block of a Massey Ferguson MF 4690 COMBINE HYBRID CLASS 4 - TIER3 engine. It lists 40 parts that make up the cylinder block, including the cylinder block itself, camshaft bearing bushes, cylinder liners, plugs, seals, and other components. Each part is identified by part number and quantity used.
This document provides disassembly instructions for the final drive carriers, hubs, and brakes of the rear and front axles of an M318 Excavator. It outlines 32 steps to disassemble the rear axle components which include removing drain plugs, planetary carriers, gears, discs, seals, and other parts. It then provides 9 steps to disassemble the front axle planetary carrier. Required tools are listed. Safety notices are also provided.
This document contains a table of contents and sections for a service manual for a Massey Ferguson 9545/9565 combine. The table of contents lists 21 sections related to different systems of the combine, including the engine and fuel system, drive system, axles, frame and more. One section summarized here is the exhaust installation section, which includes a diagram and lists of parts related to the exhaust system, such as exhaust pipes, clamps, and shields.
Kubota mx5100 h tractor parts catalogue manualfjsjekkdmnem
This parts book provides information on parts for an engine. It lists part numbers, names, quantities, interchangeability, serial number ranges and other details. Notes explain country codes that may be included and differences in other regions. The document is intended to allow identification of correct replacement parts by part number and serial number range.
Clark npr 20 forklift service repair manualfjsjekkdmnem
This document is the service manual for Clark NPR-345 trucks. It contains safety cautions and detailed instructions for maintenance, repair, and overhaul of systems including electrical, hydraulic, brakes, steering, and other components. The manual is copyrighted and intended only for Clark dealers. It includes a table of contents listing the sections and their page numbers, along with pictorial indexes to identify components.
This document provides assembly instructions for a rear differential in 3 steps or less:
1. Determine the correct shim thickness for the inner pinion bearing using a series of measurement calculations.
2. Adjust the rolling torque of the pinion shaft by changing the shim thickness until it measures within specifications.
3. Assemble the remaining differential components like the ring gear, case halves, and differential gears.
Clark npr 17 forklift service repair manualfjsjekkdmnem
This document is the service manual for Clark NPR-345 trucks. It contains safety cautions and detailed instructions for maintenance, repair, and overhaul of systems including electrical, hydraulic, brakes, steering, and other components. The manual is copyrighted and intended only for Clark dealers. It includes a table of contents that lists all sections by group number, section number, and page number for easy reference to specific repair procedures. Pictorial indexes provide illustrations of components.
Caterpillar cat m320 f wheeled excavator (prefix fb2) service repair manual (...fjsjekkdmnem
This document provides assembly instructions for a piston pump used in a wheeled excavator model M320F. It consists of 50 steps to assemble the various components of the pump in the correct order. The components include springs, retainers, seals, valves, plates, bushings, shafts, and other parts. Precautions are provided for parts that are spring loaded to prevent injury during assembly.
Caterpillar cat m320 f wheeled excavator (prefix f2w) service repair manual (...fjsjekkdmnem
The document provides instructions for disassembling and assembling the rear axle of a M320F Wheeled Excavator. It lists the required tools and gives step-by-step instructions for removing components such as the carrier housing, planetary gears, brake discs, and hub. Reassembly instructions are also provided, describing how to install components like the thrust washer, carrier gear, and retaining rings. The purpose is to repair or replace parts in the rear axle transmission.
This document provides instructions for removing a crankshaft from a Caterpillar 3116 engine. The steps include:
1. Removing the cylinder head, crankshaft rear seal carrier, and front gear group.
2. Removing the crankshaft main bearing caps and bearings.
3. Using a bearing removal tool to pull the crankshaft from the engine block.
John deere 1565 front mower service repair manualfjsjekkdmnem
This technical manual provides service information for John Deere front mowers models 1420, 1435, 1445, 1545, and 1565. The manual is organized into specific sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, tests and adjustments, repair, and safety precautions. Technicians are advised to follow all safety procedures when servicing equipment to avoid injury from hazards like high pressure fluids, moving parts, hot surfaces, and heavy components.
John deere 1545 front mower service repair manualfjsjekkdmnem
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides procedures to check each component and make any necessary repairs or adjustments.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F LN EXCAVATOR KFT
Configuration: 336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i03863290
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 by 250 mm (10 inch) Threaded Rod 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the travel motor.
1. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
1/10
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
3. Remove bolts (1).
4. Remove head (2) from the body of the travel motor.
2/10
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00887302
5. Remove O-ring seal (3), port plate (4), and bearing (5).
Illustration 3 g00887311
6. Remove O-ring seals (6). Remove springs (7).
Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B).
3/10
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 7. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
8. Remove seal (9) and backup ring (10) from the brake piston.
9. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
10. Remove plates (13) and friction discs (14).
4/10
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g02107957
Illustration 9 g00887405
Illustration 10 g00887424
11. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
12. Remove Tooling (C) from shaft (15).
13. Remove shaft (15) from rotating assembly (16).
Illustration 11 g00887426
5/10
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Use Tooling (D) in order to remove retaining ring (17) from shaft (15).
Illustration 12 g00887445
15. Use a suitable press in order to remove bearing race (18) from shaft (15).
Illustration 13 g00887463
16. Rotate shaft (15). Use a suitable press and tooling (E) in order to remove bearing race (19)
from shaft (15).
Illustration 14 g00887501
17. Remove cam plate (20) from barrel assembly (21).
6/10
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g00887520
18. Remove piston assemblies and retainer plate (22) from barrel assembly (21).
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g00887558
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Remove ball (23) and springs (24).
7/10
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g02107975
20. Remove bearing (25).
21. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
22. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27).
23. Remove lip seal (28).
Illustration 19 g00887619
24. Remove bolts (29) and cover (30).
8/10
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g00887729
25. Remove seal (31) and backup ring (32).
Illustration 21 g00887754
26. Remove piston actuator (33) and seal (34).
Illustration 22 g00887762
27. Remove O-ring seal (35) from the housing of the travel motor.
9/10
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F LN EXCAVATOR KFT
Configuration: 336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07195340
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C
6V-5215 M8 X 1.25 X 16 MM Bolt 2
9M-1974 M8 Hard Washer 2
D 1P-0510 Driver Gp 1
Start By:
a. Remove travel motor.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/14
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06249277
1. Fasten travel motor (1) in a vertical position on Tooling (A). The weight of travel motor (1)
is approximately 82 kg (180 lb).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2. Remove bolts (2) and cap (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
2/14
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 2 g06249309
Illustration 3 g06249323
Illustration 4 g06249325
3. Remove bolts (4) and cap (5).
4. Remove spring (6), spring (9), spool assembly (8), and spring seats (7).
3/14
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 5 g06249329
5. Remove plug (11), relief valve (10), and the O-ring seals.
Illustration 6 g06249334
6. Remove plug (13), relief valve (12), and the O-ring seals.
Illustration 7 g06249337
7. Remove plug (14), and the O-ring seal.
4/14
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 8 g06249341
Illustration 9 g06249344
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove plug (15), spool assembly (16), spring (17), and the O-ring seals.
5/14
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 10 g06249348
9. Remove plugs (18) and the O-ring seals.
Illustration 11 g06249351
10. Remove bolts (19).
Illustration 12 g06249354
11. Attach Tooling (B) and a suitable lifting device to motor head assembly (20). The weight of
motor head assembly (20) is approximately 27 kg (60 lb). Remove motor head assembly
(20).
6/14
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 13 g06250338
12. Remove the ball bearing that is located on the bottom side of motor head assembly (20).
Illustration 14 g06249364
Port plate (25) may still be adhered to the bottom of motor head assembly (20).
13. Remove O-ring seals (21), O-ring seal (22), springs (23), springs (24), and port plate (25).
Note: Note the location of springs (23). They must be installed in the same location during
the assembly procedure.
Illustration 15 g06249511
7/14
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 14. Insert Tooling (C) into piston assembly (26). Use a suitable prying device and Tooling (C)
to remove piston assembly (26).
Illustration 16 g06250418
15. Remove O-ring seal (27) and O-ring seal (28).
Illustration 17 g06249522
16. Use suitable prying devices to remove guide assembly (29).
Illustration 18 g06249535
17. Remove O-ring seal (30).
8/14
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 19 g06249539
Illustration 20 g06249544
18. Remove separator plates (31) and friction plates (32). Note the alternating order of separator
plates (31) and friction plates (32) for assembly purposes.
Illustration 21 g06249564
19. Remove barrel assembly (33).
Note: Do not allow the components of barrel assembly (33) to come apart while you
remove barrel assembly (33). The components of barrel assembly (33) must be reinstalled
into the original positions.
9/14
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 22 g06249598
Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
20. Remove piston assemblies (34) and retainer (35).
Illustration 23 g06249609
21. Remove hold down ball (36).
Illustration 24 g06249621
10/14
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 ...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 22. Remove dowel pins (37).
Illustration 25 g06249657
23. Put location marks on swashplate (38) for assembly purposes. Remove swashplate (38).
Illustration 26 g06249682
24. Remove pistons (39) and the balls.
Illustration 27 g06249751
25. Remove springs (40).
11/14
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 ...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 28 g06249755
Illustration 29 g06249758
26. Use a suitable press and Tooling (D) to remove snap ring (41), spacers (42), and spring (43).
12/14
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 ...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 30 g06249760
27. Use a soft faced hammer to remove shaft assembly (44). Remove shaft assembly (44) in the
direction that is indicated by the arrow.
28. Remove O-ring seal (45).
Illustration 31 g06249762
29. Remove lip seal (46).
Illustration 32 g06249763
30. Use a suitable press to push shaft (47) out of bearing (48).
13/14
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 ...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F LN EXCAVATOR KFT
Configuration: 336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
336F L & 336F LN Excavators KFT00001-UP (MACHINE) POWERED BY C9.3 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...