The document provides instructions for removing and installing engine components on a Caterpillar 336D2 L excavator including:
1. Removal and installation procedures for valve guides and valve seat inserts in the engine cylinder head.
2. Procedures for removing the engine oil filter base, oil cooler, and disassembling the oil filter base.
3. Assembly instructions for reassembling the engine oil filter base.
Caterpillar cat 336 d2 l excavator (prefix wbc) service repair manual (wbc000...pfiskdmjekm
This service manual document provides instructions for repairing and servicing excavator models 336D2 and 336D2 L. It includes procedures for removing and installing valve guides, valve seat inserts, the engine oil filter base, and oil cooler. Technicians are advised to keep parts clean and contain fluids during repair. Tools required are listed for each procedure.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujjdfjkksekmem
This document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator. It describes how to remove and install the crankshaft rear seal using various tools. It also describes removing and installing the flywheel housing, removing the idler gear from the front gear group, and removing and installing the crankshaft front seal. The document provides detailed step-by-step instructions and illustrations for each procedure.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 336 d2 l excavator (prefix wbc) service repair manual (wbc000...pfiskdmjekm
This service manual document provides instructions for repairing and servicing excavator models 336D2 and 336D2 L. It includes procedures for removing and installing valve guides, valve seat inserts, the engine oil filter base, and oil cooler. Technicians are advised to keep parts clean and contain fluids during repair. Tools required are listed for each procedure.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujjdfjkksekmem
This document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator. It describes how to remove and install the crankshaft rear seal using various tools. It also describes removing and installing the flywheel housing, removing the idler gear from the front gear group, and removing and installing the crankshaft front seal. The document provides detailed step-by-step instructions and illustrations for each procedure.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 320 d lrr excavator (prefix dhe) service repair manual (dhe00...fjsekdmmeed
This document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. The oil pump removal process involves taking off the front housing cover and various gears. The water pump removal requires removing the belt and pump pulley. Both pumps are disassembled by removing mounting components using various tools. Reassembly follows the reverse order and procedures provide guidance on cleaning, inspection and installation of seals.
Caterpillar cat 336 d2 l excavator (prefix elr) service repair manual (elr000...pfiskdmjekm
This document provides instructions for removing and installing unit injector sleeves and the unit injector hydraulic pump on Caterpillar C9 engines. The procedures include draining coolant, using various tools to cut threads and remove the sleeves, cleaning parts, applying retaining compound, reinstalling sleeves and O-rings, and reconnecting fuel lines and electrical harnesses when installing the pump. Technicians are advised to keep parts clean and contain fluids properly during the process.
Caterpillar cat 324 d ln excavator (prefix kjr) service repair manual (kjr000...JayHaines2
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document contains illustrations and specifies any required tools. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 325 c l excavator (prefix btd) service repair manual (btd0000...fjkskedmme
The document provides step-by-step instructions for disassembling and assembling the piston motor of an excavator. It lists 22 steps for disassembly, which include removing the key, cover, port plate, bearings, valve assembly, and other components. It then lists 16 steps for assembly, which involve installing components in reverse order and ensuring proper seating and alignment of parts like bearings, seals, and the rotating group. Cleanliness is emphasized throughout and special tools are required for tasks like compressing springs.
Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh0000...pfiskdmjekm
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. The summary is:
1) To remove the flywheel housing, first remove the electric starting motor and flywheel. Then use lifting tools to remove the housing bolts and housing.
2) To install the flywheel housing, first install a new oil seal and check the dowels. Clean the mating surfaces and install a new gasket on the cylinder block. Place the housing in position and install the bolts to secure it.
3) The document also provides instructions for removing the flywheel, crankshaft rear seal, and installing the rear seal.
The document provides instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, and removing the fuel transfer pump from a Caterpillar 3306 engine. The procedures include:
- Turning off the fuel supply and disconnecting tubes and hoses
- Removing bolts and washers securing components and lifting parts off
- Checking condition of gaskets and installing new ones if needed
- Reinstalling components by securing with bolts and reconnecting tubes and hoses
The instructions emphasize cleaning parts and containing fluids during disassembly and reinstallation.
Caterpillar cat 312 b excavator (prefix 8jr) service repair manual (8jr00001 ...fjsekksmemm
The documents provide instructions for servicing components of the engine in a 312B L excavator. It describes how to disassemble, inspect, and reassemble the water pump. The instructions include removing the water pump from the engine, disassembling it into individual parts like the impeller and shaft, inspecting parts for wear, replacing the seal if needed, and reassembling the water pump using the appropriate tools and specifications. Proper cleanup and installation procedures are emphasized to prevent contamination.
Caterpillar cat 235 d excavator (prefix 8kj) service repair manual (8kj00001 ...uudfjjjskkemmd
The document provides instructions for removing and disassembling the fuel transfer pump on a Caterpillar 235D Excavator with a 3306 engine. The removal procedure involves turning off the fuel supply, disconnecting tubes, and removing bolts to access the pump. The disassembly process describes removing springs, seals, sleeves, pistons, and other components from the pump housing. Safety notices are provided to keep parts clean and contain fluids during maintenance.
Caterpillar cat 336 d2 l excavator (prefix wbc) service repair manual (wbc000...fjjskekdmmem
This service manual document provides instructions for repairing and servicing excavator models 336D2 and 336D2 L. It includes procedures for removing and installing valve guides, valve seat inserts, the engine oil filter base, and oil cooler. Technicians are advised to keep parts clean and contain fluids during repair work. Detailed illustrations accompany the step-by-step instructions for each procedure.
The document provides instructions for removing and installing engine oil filter bases, oil coolers, valve guides, and valve seat inserts on Caterpillar 336D2 and 336D2L excavators. The procedures include using various tools to disconnect hoses, remove bolts, and extract or install components. Technicians are advised to keep parts clean and contain fluids during the repair process.
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...zatao0179249295
The document provides instructions for servicing components of a Caterpillar 336D2 L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...luanxianshi27
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...cnp692569
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
1) The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) The procedures describe disconnecting hoses and electrical connections, removing mounting bolts and identifying parts to ensure proper reinstallation.
3) Safety notices emphasize the importance of cleanliness and containing fluids to prevent contamination and environmental damage.
The document provides instructions for removing and installing a pump drive on a C18 Industrial Engine. It includes:
1) A list of required tools and safety notices for working on the engine.
2) Step-by-step instructions to disassemble the pump drive by removing components like bolts, gears, and bearings.
3) Parallel steps for reassembling the pump drive, including installing new seals and adjusting end play.
4) Instructions for installing the fully reassembled pump drive back onto the engine.
This service repair manual provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a Caterpillar C11 industrial engine. The procedures describe using various tools to remove and install components in a specific sequence, and include safety notices and illustrations. Removal involves disconnecting hoses, removing retaining components, and extracting parts from the cylinder head or engine. Installation is the reverse of removal.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document includes illustrations to identify the specific components and tools required for each procedure.
The document provides instructions for removing and installing various engine components on a Caterpillar C9.3B industrial engine. It includes steps for removing and installing the crankshaft rear seal, flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, and housing (front). Diagrams and part numbers for required tools are provided for each procedure. The document is part of a service manual for Caterpillar technicians repairing C9.3B engines.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
Caterpillar cat 320 d lrr excavator (prefix dhe) service repair manual (dhe00...fjsekdmmeed
This document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. The oil pump removal process involves taking off the front housing cover and various gears. The water pump removal requires removing the belt and pump pulley. Both pumps are disassembled by removing mounting components using various tools. Reassembly follows the reverse order and procedures provide guidance on cleaning, inspection and installation of seals.
Caterpillar cat 336 d2 l excavator (prefix elr) service repair manual (elr000...pfiskdmjekm
This document provides instructions for removing and installing unit injector sleeves and the unit injector hydraulic pump on Caterpillar C9 engines. The procedures include draining coolant, using various tools to cut threads and remove the sleeves, cleaning parts, applying retaining compound, reinstalling sleeves and O-rings, and reconnecting fuel lines and electrical harnesses when installing the pump. Technicians are advised to keep parts clean and contain fluids properly during the process.
Caterpillar cat 324 d ln excavator (prefix kjr) service repair manual (kjr000...JayHaines2
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document contains illustrations and specifies any required tools. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 325 c l excavator (prefix btd) service repair manual (btd0000...fjkskedmme
The document provides step-by-step instructions for disassembling and assembling the piston motor of an excavator. It lists 22 steps for disassembly, which include removing the key, cover, port plate, bearings, valve assembly, and other components. It then lists 16 steps for assembly, which involve installing components in reverse order and ensuring proper seating and alignment of parts like bearings, seals, and the rotating group. Cleanliness is emphasized throughout and special tools are required for tasks like compressing springs.
Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh0000...pfiskdmjekm
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. The summary is:
1) To remove the flywheel housing, first remove the electric starting motor and flywheel. Then use lifting tools to remove the housing bolts and housing.
2) To install the flywheel housing, first install a new oil seal and check the dowels. Clean the mating surfaces and install a new gasket on the cylinder block. Place the housing in position and install the bolts to secure it.
3) The document also provides instructions for removing the flywheel, crankshaft rear seal, and installing the rear seal.
The document provides instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, and removing the fuel transfer pump from a Caterpillar 3306 engine. The procedures include:
- Turning off the fuel supply and disconnecting tubes and hoses
- Removing bolts and washers securing components and lifting parts off
- Checking condition of gaskets and installing new ones if needed
- Reinstalling components by securing with bolts and reconnecting tubes and hoses
The instructions emphasize cleaning parts and containing fluids during disassembly and reinstallation.
Caterpillar cat 312 b excavator (prefix 8jr) service repair manual (8jr00001 ...fjsekksmemm
The documents provide instructions for servicing components of the engine in a 312B L excavator. It describes how to disassemble, inspect, and reassemble the water pump. The instructions include removing the water pump from the engine, disassembling it into individual parts like the impeller and shaft, inspecting parts for wear, replacing the seal if needed, and reassembling the water pump using the appropriate tools and specifications. Proper cleanup and installation procedures are emphasized to prevent contamination.
Caterpillar cat 235 d excavator (prefix 8kj) service repair manual (8kj00001 ...uudfjjjskkemmd
The document provides instructions for removing and disassembling the fuel transfer pump on a Caterpillar 235D Excavator with a 3306 engine. The removal procedure involves turning off the fuel supply, disconnecting tubes, and removing bolts to access the pump. The disassembly process describes removing springs, seals, sleeves, pistons, and other components from the pump housing. Safety notices are provided to keep parts clean and contain fluids during maintenance.
Caterpillar cat 336 d2 l excavator (prefix wbc) service repair manual (wbc000...fjjskekdmmem
This service manual document provides instructions for repairing and servicing excavator models 336D2 and 336D2 L. It includes procedures for removing and installing valve guides, valve seat inserts, the engine oil filter base, and oil cooler. Technicians are advised to keep parts clean and contain fluids during repair work. Detailed illustrations accompany the step-by-step instructions for each procedure.
The document provides instructions for removing and installing engine oil filter bases, oil coolers, valve guides, and valve seat inserts on Caterpillar 336D2 and 336D2L excavators. The procedures include using various tools to disconnect hoses, remove bolts, and extract or install components. Technicians are advised to keep parts clean and contain fluids during the repair process.
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...zatao0179249295
The document provides instructions for servicing components of a Caterpillar 336D2 L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...luanxianshi27
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...cnp692569
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Similar to Caterpillar cat 336 d2 l excavator (prefix wbc) service repair manual (wbc00001 and up) (8)
1) The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) The procedures describe disconnecting hoses and electrical connections, removing mounting bolts and identifying parts to ensure proper reinstallation.
3) Safety notices emphasize the importance of cleanliness and containing fluids to prevent contamination and environmental damage.
The document provides instructions for removing and installing a pump drive on a C18 Industrial Engine. It includes:
1) A list of required tools and safety notices for working on the engine.
2) Step-by-step instructions to disassemble the pump drive by removing components like bolts, gears, and bearings.
3) Parallel steps for reassembling the pump drive, including installing new seals and adjusting end play.
4) Instructions for installing the fully reassembled pump drive back onto the engine.
This service repair manual provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a Caterpillar C11 industrial engine. The procedures describe using various tools to remove and install components in a specific sequence, and include safety notices and illustrations. Removal involves disconnecting hoses, removing retaining components, and extracting parts from the cylinder head or engine. Installation is the reverse of removal.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document includes illustrations to identify the specific components and tools required for each procedure.
The document provides instructions for removing and installing various engine components on a Caterpillar C9.3B industrial engine. It includes steps for removing and installing the crankshaft rear seal, flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, and housing (front). Diagrams and part numbers for required tools are provided for each procedure. The document is part of a service manual for Caterpillar technicians repairing C9.3B engines.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...fjjskmdmem
The document provides instructions for removing and installing wheel spindle assemblies on a Caterpillar 966C wheel loader. Key steps include removing the brake shoes, brake camshaft, and air lines before removing the spindle assembly using a hoist. Installation involves installing seals and bearings on the spider and bearing assembly before placing it on the spindle and securing with nuts. Brake components and air lines are then reinstalled.
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g010...fjjskmdmem
This document provides instructions for removing and installing various components of the 966C wheel loader's power train, including wheels, brake shoes, wheel spindles, the front differential and carrier, and the rear differential and carrier. The procedures involve draining fluids, removing bolts and seals, using hoists and jacks, and reinstalling components in the reverse order while applying lubricants and torques as specified. Safety precautions are noted such as relieving air pressure from brake systems before disconnecting lines.
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...fjjskmdmem
The document provides instructions for removing and installing various components of the rear differential and carrier assembly of a 966C wheel loader, including removing the rear axles, disconnecting air lines, removing mounting bolts and lifting the rear of the machine to access the differential and carrier. The rear differential and carrier unit weighs 350 pounds and houses the internal gears that allow the rear wheels to turn at different speeds.
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j063...fjjskmdmem
This document provides instructions for removing and installing various components of the power train on a 966C wheel loader, including axles, final drive planet carriers, final drive ring gears and hubs, and wheels/bearings. The procedures describe draining oil, removing retaining rings and gears, and reinstalling components along with adjusting wheel bearings and installing seals.
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j000...fjjskmdmem
This document provides instructions for removing and installing various components of the final drive and wheel assembly of a 966C wheel loader, including:
- Removing and installing final drive planet carriers
- Disassembling and assembling final drive planet carriers
- Removing and installing final drive ring gears, hubs, and wheels
- Removing and installing wheels, bearings, and seals
- Removing and installing brake shoes
The document contains detailed step-by-step instructions and diagrams for each procedure.
Caterpillar cat 966 c wheel loader (prefix 18b) service repair manual (18b012...fjjskmdmem
The document provides instructions for disassembling and assembling the fuel injection pump housing of a Caterpillar 966C wheel loader. It describes:
1) Removing components like the fuel rack, lifters, camshaft, and bearings during disassembly.
2) Cleaning and lubricating parts before assembly.
3) Installing bearings, camshaft, lifters, fuel rack, and other components in reverse order of removal.
4) Timing the fuel injection pump housing and governor during installation on the engine.
Caterpillar cat 966 c wheel loader (prefix 18b) service repair manual (18b002...fjjskmdmem
1. The documents provide instructions for removing, installing, and servicing components of the engine oil filter base and cylinder head valves for a Caterpillar 966C wheel loader.
2. The procedures include using various tools to remove and install valves, valve guides, valve seat inserts, and the engine oil filter base.
3. Precautions are provided such as keeping parts clean and containing fluids during repair work.
Caterpillar cat 950 e wheel loader (prefix 65r) service repair manual (65r030...fjjskmdmem
The document provides instructions for removing and installing various components of the front and rear axle assemblies of a Caterpillar 950B wheel loader, including wheel spindles, front and rear axle housings, rear axle housing supports, and the front drive shaft and carrier bearing. The instructions include lists of required tools and parts, diagrams illustrating the component locations and removal/installation steps, and torque specifications for reinstalling components. Safety precautions are noted, such as blocking wheels and releasing parking brakes before removing drive shafts.
Caterpillar cat 950 e wheel loader (prefix 63r) service repair manual (63r060...fjjskmdmem
This document provides instructions for disassembling and assembling the transfer gears of a Caterpillar 950B wheel loader. It describes removing and installing over 30 individual parts in 14 steps. Key steps include using bolts and screws to separate the transmission from the transfer gears, removing bearing cages and gears, and checking bearing end play during reassembly. Proper heating and cooling of parts is emphasized during assembly/disassembly. The document also provides brief instructions for connecting and disconnecting the steering frame lock link and removing and installing the loader bucket.
Caterpillar cat 950 e wheel loader (prefix 22z) service repair manual (22z031...fjjskmdmem
This document provides instructions for removing and installing a crankshaft on a Caterpillar 3304B or 3306B engine. It describes using various tools to remove the crankshaft by lifting it straight up after removing connecting rods, caps and bolts. It also details installing new main and connecting rod bearings, checking clearances with plastigage, and reinstalling the crankshaft by lowering it into place and reattaching connecting rods and caps. A second section provides steps for accurately checking bearing clearances using plastic gauge strips.
Caterpillar cat 950 e wheel loader (prefix 22z) service repair manual (22z000...fjjskmdmem
1. The document provides instructions for disassembling and assembling components of the fuel injection system for Caterpillar 3304B and 3306B engines, including the fuel injection pump housing, governor, and related parts.
2. The procedures include removing and installing bearings, camshafts, lifters, racks, gaskets and covers using various tools. Proper positioning and torque specifications are provided.
3. Detailed illustrations accompany each step to show how to disassemble and assemble the parts in the correct order and orientation.
Caterpillar cat 950 b wheel loader (prefix 65r) service repair manual (65r030...fjjskmdmem
The document provides instructions for removing and installing various components of the front and rear axle assemblies of a Caterpillar 950B wheel loader, including wheel spindles, front and rear axle housings, rear axle housing supports, and the front drive shaft and carrier bearing. The instructions include numbered steps detailing how to properly support and secure the components, which fasteners to remove and install, and proper torques to use.
Caterpillar cat 950 b wheel loader (prefix 65r) service repair manual (65r028...fjjskmdmem
The document provides instructions for removing and installing an exhaust manifold on a Caterpillar 950B wheel loader. Key steps include removing the turbocharger, fuel injection lines, exhaust manifold nuts and bolts, and exhaust manifold gaskets. When installing, apply anti-seize compound to studs if removed previously and ensure the two longer studs are in the correct position. Proper cleaning and installation of all parts is emphasized to prevent contamination.
Caterpillar cat 950 b wheel loader (prefix 65r) service repair manual (65r000...fjjskmdmem
This document provides instructions for removing and installing various components of a Caterpillar 3304 engine, including the spacer plate, water directors, lifter group, camshaft, and camshaft bearings. The procedures provide detailed steps and illustrations for each component, with notices to keep parts clean and properly align timing marks.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i05165105
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6895
or
4C-6366 (1)
Valve Guide Driver 1
( 1 )
If necessary, use Tooling on inlet valve guides.
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g01137612
1. Use Tooling (A) to remove the inlet valve guides and exhaust valve guides from the
cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
9U-6895
or
4C-6366 (1)
Valve Guide Driver 1
B 173-5524 Guide Collar 1
C 342-6109 Guide Collar 1
( 1 )
If necessary, use Tooling on inlet valve guides.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g03317961
1. Position the inlet valve guide and exhaust valve guide in the cylinder head. Tap on the top
of the valve guides in order to start the inlet valve guides and exhaust valve guides into the
cylinder head assembly.
2. Use Tooling (A) and Tooling (B) to install the Exhaust valve guide. Use Tooling (A) and
Tooling (C) to install the Intake valve guide. Install the valve guides until the protrusion is
Distance (X) . Distance (X) is 12.0 ± 0.5 mm (0.47 ± 0.02 inch) above the cylinder head
assembly.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 3 17:28:37 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i04420274
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-3095 Puller Handle 1
B
6V-4194 (1)
Valve Seat Extractor 1
1U-9167 (2)
Valve Seat Extractor 1
( 1 )
For use with Exhaust Valve Seat
( 2 )
For use with Intake Valve Seat
Start By:
A. Remove inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
1/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 1 g01137634
1. Use Tooling (A) and Tooling (B) to remove valve seat inserts (1) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
C
4C-6372 (1)
Valve Seat Driver 1
364-4009 (2)
Valve Seat Driver 1
( 1 )
For use with Exhaust Valve Seat
( 2 )
For use with Intake Valve Seat
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 2 g01137637
Note: Do not machine the prefinished valve seat inserts in order to correct the valve stem
projection. An excessive valve stem projection indicates that the valve seat insert is not
seated or material was not cleaned from the bottom of the counterbore.
1. Lower the temperature of new valve seat inserts (1) . Use Tooling (C) to install valve seat
inserts (1) into the cylinder head.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 3 17:29:32 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i02297805
Engine Oil Filter Base and Oil Cooler - Remove
SMCS - 1306-011; 1378-012
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
1/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01150737
1. Use Tooling (A) to remove engine oil filter (1).
2/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 2 g01150959
2. Disconnect hose assembly (2). Remove bolts (3). Remove engine oil filter base (4) and the
oil seal.
3/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 3 g01150963
3. Remove engine oil cooler (5).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 3 17:30:28 UTC+0800 2020
4/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i02298275
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base and Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 1 g01151723
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove elbow (1) and O-ring seal (3) from engine oil filter base (6).
2. Remove plug (2) and the O-ring seal from engine oil filter base (6).
3. Remove spring (4) and valve (5) from engine oil filter base (6).
4. Remove plug (9) and the O-ring seal from engine oil filter base (6).
5. Remove spring (8) and valve (7) from engine oil filter base (6).
Wed Jun 3 17:31:24 UTC+0800 2020
2/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
3/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i02300235
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 1 g01151723
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Apply clean engine oil to O-ring seal (3). Install O-ring seal (3) on elbow (3). Install elbow
(1) in engine oil filter base (6).
2. Apply clean engine oil to the O-ring seal. Install the O-ring seal on plug (2).
3. Apply clean engine oil to valve (5). Install valve (5), spring (4), and plug (2) in engine oil
filter base (6).
4. Apply clean engine oil to the O-ring seal. Install the O-ring seal on plug (9).
5. Apply clean engine oil to valve (7). Install valve (7), spring (8), and plug (9) in engine oil
filter base (6).
2/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base and Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 3 17:32:20 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i02298181
Engine Oil Filter Base and Oil Cooler - Install
SMCS - 1306-012; 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 2 g01150959
2. Apply clean engine oil to the oil seal. Install the oil seal in engine oil filter base (4). Position
engine oil filter base (4) over the engine oil cooler. Install bolts (3). Connect tube assembly
(2).
3/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 3 g01150737
3. Install engine oil filter (1).
4. Fill the engine with oil to the correct level. Refer to Operation and Maintenance Manual,
"Refill Capacities and Recommendations".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 3 17:33:16 UTC+0800 2020
4/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i02298281
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01151740
1. Remove bolts (1).
2. Remove bolt (2).
3. Remove bolts (3) and remove engine oil pump (4).
4. Remove the O-ring seal that is located between the cylinder block and the outlet elbow.
2/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 2 g01152424
5. Remove bolts (5) and remove outlet elbow (6).
6. Remove bolts (7). Remove oil pickup tube (8) and the gasket.
Illustration 3 g01152433
3/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. 7. Remove bolt (12) and the washer. Remove idler gear (11). Use Tooling (A) in order to
remove bearing (10) from idler gear (11). Remove shaft (9) from engine oil pump (4).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 3 17:34:11 UTC+0800 2020
4/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i07521711
Engine Oil Pump - Install
SMCS - 1304-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. Illustration 1 g01152433
1. Install shaft (9) onto engine oil pump (4). Use Tooling (A) and a suitable press in order to
install bearing (10) into idler gear (11). Position idler gear (11) on shaft (9). Install bolt (12)
and the washer.
Illustration 2 g06348586
2. Mount the engine oil pump (4) to the cylinder block by hand tightening the mounting bolts
(3) into the cylinder block.
Note: Ensure that the mounting surfaces for the engine oil pump are thoroughly clean.
3. Without the O-rings, assemble the outlet elbow (6) between the block and the oil pump,
using the washers and bolts (2) and (5). Hand tighten only.
2/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...