The document provides instructions for removing and installing various components of the front and rear axle assemblies of a Caterpillar 950B wheel loader, including wheel spindles, front and rear axle housings, rear axle housing supports, and the front drive shaft and carrier bearing. The instructions include lists of required tools and parts, diagrams illustrating the component locations and removal/installation steps, and torque specifications for reinstalling components. Safety precautions are noted, such as blocking wheels and releasing parking brakes before removing drive shafts.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 65R
Configuration: 950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
950B WHEEL LOADER POWER TRAIN
Media Number -SENR2258-01 Publication Date -01/05/1987 Date Updated -15/09/2004
SENR22580009
Wheel Spindles
SMCS - 4205-010
Remove And Install Wheel Spindles
Start By:
a. remove wheels, bearings and duo-cone seals
1. Fasten tool (A) and a hoist to spindle (1). Remove the bolts and spindle (1). The weight of the
spindle is 27 kg (60 lb.).
1/2
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Remove O-ring seal (2) from the spindle.
3. Remove bolts (3) and remove the retainer from the spindle.
4. Remove O-ring seal (4) from retainer (5).
NOTE: The following steps are for the installation of the wheel spindles.
5. Install O-ring seal (4) in position on retainer (5).
6. Install retainer (5) on the spline side of the spindle (3).
7. Install O-ring seal (2) on the back of the spindle.
8. Fasten tool (A) and a hoist to spindle (1). Put the spindle in position on the axle housing and
install the bolts. Tighten the bolts to a torque of 475 ± 50 N·m (350 ± 37 lb.ft.).
End By:
a. install wheels, bearings and duo-cone seals
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 10 02:54:58 UTC+0800 2020
2/2
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 65R
Configuration: 950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
950B WHEEL LOADER POWER TRAIN
Media Number -SENR2258-01 Publication Date -01/05/1987 Date Updated -15/09/2004
SENR22580010
Front Axle Housing
SMCS - 3260-010
Remove And Install Front Axle Housing
Start By:
a. remove tires and rims (front)
b. remove front drive shaft
1. Lift the bucket and put tooling (A) in position under the lift arms as shown. This will permit
access to the front axle bolts.
1/2
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 2. Disconnect brake line (1) from the junction box as shown.
3. Fasten nylon straps (2) and hoist to front axle housing (3) as shown.
4. Remove nuts (4), the bolts and the washers. Carefully lower front axle housing from the
machine. The weight of the axle housing is 953 kg (2100 lb.).
NOTE: The following steps are for the installation of the front axle housing.
5. Fasten nylon straps (2) and hoists to axle housing (3).
6. Put axle housing (3) into position on the machine as shown.
7. Install the bolts, the washers and nuts (4) that hold the axle housing to the machine. Tighten the
nuts to a torque of 275 ± 35 N·m (200 ± 26 lb.ft.).
8. Connect brake line (1) to the junction box. Remove (bleed) the air from the brake system.
9. Remove tooling (A).
End By:
a. install front drive shaft
b. install tires and rims (front)
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 10 02:55:55 UTC+0800 2020
2/2
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 65R
Configuration: 950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
950B WHEEL LOADER POWER TRAIN
Media Number -SENR2258-01 Publication Date -01/05/1987 Date Updated -15/09/2004
SENR22580011
Rear Axle Housing
SMCS - 3260-010
Remove And Install Rear Axle Housing
Start By:
a. remove tires and rims (rear)
b. remove rear drive shaft
1. Disconnect brake line (1) from the top of axle housing.
2. Disconnect grease line (2) from the top of the rear support and the grease line from the top of
the front support.
1/3
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 3. Fasten nylon straps (3) and a hoist to rear axle housing (4) as shown.
4. Fasten a chain around the axle housing front support (6) and yoke (5) to hold front support (6)
and yoke (5) in position.
5. Remove nuts (7) and the washers from both the front and rear supports.
6. Make sure all lines are disconnected and carefully lower the rear axle housing from the
machine. The weight of the rear axle housing is 1089 kg (2400 lb.).
NOTE: The following steps are for the installation of the rear axle housing.
7. Fasten a chain to front support (6) and yoke (5) to hold them in position.
8. Put nylon straps (3) in position on both sides of the rear axle housing. Lift the axle housing into
position on the machine.
9. Make sure the dowels in front support (6) are in alignment with the holes in the frame.
10. Install the washers and nuts (7) to both supports. Tighten the nuts to a torque of 475 ± 50 N·m
(350 ± 37 lb.ft.).
11. Connect grease line (2) to the rear support and the grease line to the top of the front support.
12. Connect brake line (1) at the top of the axle housing. Remove (bleed) the air from the brake
system.
End By:
a. install rear drive shaft
b. install tires and rims (rear)
Fri Apr 10 02:56:52 UTC+0800 2020
2/3
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
3/3
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 65R
Configuration: 950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
950B WHEEL LOADER POWER TRAIN
Media Number -SENR2258-01 Publication Date -01/05/1987 Date Updated -15/09/2004
SENR22580012
Rear Axle Housing Front Support
SMCS - 3268-010
Remove And Install Rear Axle Housing Front Support
Start By:
a. remove rear axle housing
1. Put the rear axle housing on blocks with the differential pinion shaft in a vertical position as
shown.
2. Pull yoke (1) off the differential pinion shaft.
1/3
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 3. Fasten nylon straps and a hoist and remove front support (2) from the differential pinion
housing. The weight of front support (2) is 34 kg (75 lb.).
4. Remove lip type seals (3) from support (2).
5. Remove ring (5) that holds bearing (4) in the support.
6. Remove lip type seal (6) and push bearing (4) out of the support from the same side ring (5)
was removed.
NOTE: The following steps are for the installation of the rear axle housing front support.
7. Use a press and tool (A) to push the bearing in support (2) until it makes contact with the
shoulder in its bore.
2/3
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 8. Install ring (5) to hold the bearing in position.
9. Use tooling (B) to install lip type seals (3) in each side of the support. Make sure the lips of the
seals are toward the outside of the support.
10. Fasten nylon straps a hoist to the front support and put front support (2) in position on the
differential pinion housing. Make sure the side of support (2) with the snap ring in it is toward the
yoke end of the pinion shaft. The grease fitting in support (2) must be toward the top of the axle
housing.
11. Install yoke (1) on the differential pinion shaft.
End By:
a. install rear axle housing
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 10 02:57:49 UTC+0800 2020
3/3
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 65R
Configuration: 950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
950B WHEEL LOADER POWER TRAIN
Media Number -SENR2258-01 Publication Date -01/05/1987 Date Updated -15/09/2004
SENR22580013
Rear Axle Housing Rear Support
SMCS - 3268-011; 3268-012
Remove Rear Axle Housing Rear Support
Start By:
a. remove rear axle housing
1. Put the rear axle housing on wooden blocks as shown.
2. Remove the bolts and cover (1) from the rear support.
1/5
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 3. Remove bolts (2), washer (3), plate (4) and the washer from the end of the trunnion.
4. Fasten straps and a hoist to support (5) and remove it from the axle housing. The weight of the
support is 39 kg (85 lb.).
5. Remove seal (6) from the support.
6. Use tooling (A) and a press and remove the bearing from the support.
2/5
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 7. Remove the bolts and disconnect bracket (7) from the trunnion.
8. Remove bolts (8) and trunnion (9) from the rear axle housing.
9. Remove the O-ring seal from the trunnion.
Install Rear Axle Housing Rear Support
1. Put O-ring seal (2) in position on the back of trunnion (9). Put clean differential oil on the O-
ring seal.
2. Install trunnion (9) on the axle housing and install the bolts. Tighten the bolts to a torque of 270
± 25 N·m (200 ± 18 lb.ft.).
3. Connect bracket (7) to the trunnion.
3/5
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 4. Use tooling (A) and install the bearing until it is even with the counterbore in support (5).
5. Use tool (A) and install seal (6) in the support. Make sure the lip of the seal is toward the
outside as shown. Put clean differential oil on the seal.
6. Fasten straps and a hoist to support (5) and put it in position on the trunnion.
7. Install washer (10), plate (4) and washer (3) in the end of the support as shown.
4/5
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 8. Install cover (1) and the bolts on the end of the support. Tighten the bolts to a torque of 475 ±
50 N·m (350 ± 37 lb.ft.).
End By:
a. install rear axle housing
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 10 02:58:46 UTC+0800 2020
5/5
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 65R
Configuration: 950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
950B WHEEL LOADER POWER TRAIN
Media Number -SENR2258-01 Publication Date -01/05/1987 Date Updated -15/09/2004
SENR22580014
Front Drive Shaft And Carrier Bearing
SMCS - 3253; 3267-016; 3267-011; 3267-012; 3267-015
Remove Front Drive Shaft And Carrier Bearing
Start By:
a. connection of steering frame lock link
b. remove center drive shaft
NOTE: Block the wheels and release the parking brake prior to the removal operation.
1. Mark the position of lever (2) on the shaft. Remove pin (1), bolt (3), and lever (2).
2. Disconnect grease line (4) from the fitting.
1/8
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 3. Remove center bolt and washer (5) from the yoke assembly.
4. Attach tool (A) to drum assembly (6). Install tool (B) to tool (A) as shown.
5. Slide the yoke and drum assembly (6) off of the brake shoe assembly and lower them to the
ground. The weight of the yoke and drum assembly is 31.7 kg (70 lb.).
6. Remove four bolts (7), and remove brake shoe assembly (8).
7. Remove the top two bolts of bolts (10) and install two 5/8"-11 NC guide bolts (9). Remove the
remaining bolts (10).
2/8
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 8. Remove bolts (11) and (13). Remove straps (12) and (14) that hold the front drive shaft to yoke
assembly (15).
9. Remove grease line (16). Use two persons to push the front drive shaft and carrier bearing
assembly (17) to the rear of the machine and remove it. The weight of the front drive shaft and
carrier bearing assembly is 31.7 kg (70 lb.).
Install Front Drive Shaft And Carrier Bearing
1. Use two persons to position front drive shaft and carrier bearing assembly (17) on the machine.
Install grease line (16).
3/8
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 2. Install straps (12) and (14), and install bolts (11) and (13) that hold the front drive shaft to yoke
assembly (15).
3. Tighten bolts (11) and (13) to a torque of 55 ± 7 N·m (41 ± 5 lb.ft.).
4. Install bolts (10). Remove the two 5/8"-11 NC guide bolts (9), and install the two remaining
bolts (10).
5. Position brake shoe assembly (8), and install four bolts (7).
6. Attach tool (A) to drum assembly (6). Install tool (B) to tool (A), and raise and slide the yoke
and drum assembly in position as shown.
4/8
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 7. Install center bolt and washer (5) on the yoke assembly. Tighten the bolt to a torque of 135 ± 15
N·m (100 ± 11 lb.ft.).
8. Connect grease line (4) to the fitting.
9. Align lever (2) with the mark on the shaft. Install lever (2), bolt (3), and pin (1).
End By:
a. install center drive shaft
b. separation of steering frame lock link
Disassemble Front Drive Shaft And Carrier Bearing
Start By:
a. remove front drive shaft and carrier bearing
1. Remove two bolts (1), and remove housing (2) from housing (3).
5/8
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 2. Remove lip type seal (4) from housing (2).
3. Use a press as shown, and press shaft (5) out of bearing (6).
4. Remove O-ring seal (7) from housing (3). Remove bearing (6) from housing (3).
Assemble Front Drive Shaft And Carrier Bearing
6/8
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 1. Use tool group (A) to install the lip seal in housing (3). Make sure the lip of the seal is toward
the inside of the housing as shown.
NOTICE
Both lip type seals for the carrier bearing housings must be installed so
the lips of the seals are toward the front drive shaft assembly to keep
grease out of the parking brake.
2. Lower the temperature of bearing (6), and install in housing (3).
3. Put clean grease on O-ring seal (7), and install it on housing (3) around the bearing.
4. Use a press as shown, and press front drive shaft assembly (8) into the bearing in housing (3).
5. Use tool group (A) to install the seal in housing (2). Make sure the lip of the seal is toward the
inside of the housing as shown.
7/8
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. 6. Put clean grease on the lip of the seal in housing (2). Install housing (2) on housing (3) and
install bolts (1).
End By:
a. install front drive shaft and carrier bearing
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 10 02:59:42 UTC+0800 2020
8/8
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 65R
Configuration: 950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
950B WHEEL LOADER POWER TRAIN
Media Number -SENR2258-01 Publication Date -01/05/1987 Date Updated -15/09/2004
SENR22580015
Center Drive Shaft
SMCS - 3253-010
Remove And Install Center Drive Shaft
1. Make sure the parking brake is released so the drive shaft can be turned.
2. Remove bolts (2) and straps (3) from both ends of drive shaft (1). Remove the drive shaft.
NOTE: The following steps are for the installation of the center drive shaft.
NOTE: Make sure all drive shaft yokes are on the same center line as the center drive shaft is
installed.
3. Put drive shaft (1) in position. Install straps (3) and bolts (2).
4. Tighten bolts (2) to a torque of 55 ± 7 N·m (41 ± 5 lb.ft.).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 10 03:00:39 UTC+0800 2020
1/1
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 65R
Configuration: 950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
950B WHEEL LOADER POWER TRAIN
Media Number -SENR2258-01 Publication Date -01/05/1987 Date Updated -15/09/2004
SENR22580016
Rear Drive Shaft
SMCS - 3253-010
Remove And Install Rear Drive Shaft
1. Remove four bolts (1), and two straps (2) that hold drive shaft (3) on each end to joint groups
(4).
2. Remove drive shaft (3) from the machine.
NOTE: The following steps are for the installation of the rear drive shaft.
3. Make sure all the drive shaft yokes in the powertrain are on the same center line.
4. Put drive shaft (3) in position.
5. Install two straps (2) and four bolts (1) on each end. Tighten bolts (1) to a torque of 55 ± 7 N·m
(41 ± 5 lb.ft.).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 10 03:01:36 UTC+0800 2020
1/1
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE...
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...