This document provides instructions for disassembling and assembling the final drive of an excavator. The disassembly procedure involves using various tools to remove over 30 individual parts in a specific sequence. The assembly procedure similarly involves installing the parts in reverse order and adjusting the bearing preload using shims to achieve the proper clearance. Special tools and techniques like applying threadlocker and leak testing are required to properly reassemble the final drive.
Caterpillar cat 330 f excavator (prefix jhf) service repair manual (jhf00001 ...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly, covers, gears, carriers, shafts, and seals. The assembly section provides instructions for installing seals, bearings, gears, carriers, and other components in the reverse order of disassembly. Special tools and precautions are noted throughout to properly set bearing preload and install seals without damage.
Caterpillar cat 330 f ln excavator (prefix jhf) service repair manual (jhf000...fksjksmmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by having the technician remove the final drive assembly and place it on a transmission repair stand. Detailed steps are then provided to disassemble the various components of the final drive including removing gears, shafts, carriers, and housing pieces. The final section provides instructions for reassembling the final drive, making sure to clean all parts and replace any damaged seals. Technicians are instructed to properly set the bearing preload when reinstalling components.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly, cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly section provides instructions for installing seals, bearings, gears, ring gear, and adjusting the bearing preload to complete reassembly of the final drive. Tools required are listed for both disassembly and assembly.
Caterpillar cat 330 f excavator (prefix jhf) service repair manual (jhf00001 ...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar cat 330 f ln excavator (prefix jhf) service repair manual (jhf000...dueikdkmem
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar Cat 330F, 330F L and 330F LN Excavator (Prefix JHF) Service Repai...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
Caterpillar Cat 330F, 330F L and 330F LN Excavator (Prefix JHF) Service Repai...zan2736ban
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, and using shims to set the proper bearing preload when reassembling components. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar Cat 330F L Excavator (Prefix JHF) Service Repair Manual (JHF00001...f8uesjdkdmdm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar cat 330 f excavator (prefix jhf) service repair manual (jhf00001 ...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly, covers, gears, carriers, shafts, and seals. The assembly section provides instructions for installing seals, bearings, gears, carriers, and other components in the reverse order of disassembly. Special tools and precautions are noted throughout to properly set bearing preload and install seals without damage.
Caterpillar cat 330 f ln excavator (prefix jhf) service repair manual (jhf000...fksjksmmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by having the technician remove the final drive assembly and place it on a transmission repair stand. Detailed steps are then provided to disassemble the various components of the final drive including removing gears, shafts, carriers, and housing pieces. The final section provides instructions for reassembling the final drive, making sure to clean all parts and replace any damaged seals. Technicians are instructed to properly set the bearing preload when reinstalling components.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly, cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly section provides instructions for installing seals, bearings, gears, ring gear, and adjusting the bearing preload to complete reassembly of the final drive. Tools required are listed for both disassembly and assembly.
Caterpillar cat 330 f excavator (prefix jhf) service repair manual (jhf00001 ...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar cat 330 f ln excavator (prefix jhf) service repair manual (jhf000...dueikdkmem
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar Cat 330F, 330F L and 330F LN Excavator (Prefix JHF) Service Repai...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
Caterpillar Cat 330F, 330F L and 330F LN Excavator (Prefix JHF) Service Repai...zan2736ban
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, and using shims to set the proper bearing preload when reassembling components. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar Cat 330F L Excavator (Prefix JHF) Service Repair Manual (JHF00001...f8uesjdkdmdm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f excavator (prefix jhf) service repair manual (jhf00001 ...dfjjsjkemmm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...idkkdmmd
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise measurements and torque specifications are provided to ensure correct assembly.
Caterpillar Cat 330F L Excavator (Prefix JHF) Service Repair Manual (JHF00001...f8uejkkdmdm8u
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar Cat 330F L Excavator (Prefix JHF) Service Repair Manual (JHF00001...8ufjsekddm8u
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...dfjjsjkemmm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. The disassembly procedure involves using various tools to remove over 30 individual parts in a specific sequence. The assembly procedure similarly provides step-by-step instructions to reinstall the parts in reverse order, noting the importance of cleaning, applying sealants, and properly setting bearing preloads.
Caterpillar cat 330 f ln excavator (prefix jhf) service repair manual (jhf000...ikdkdmdm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...dujkdksmdmdm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, and remove the front cover and gasket.
3. Clean the front cover, housing, and install a new gasket. Use guide studs to position the front cover and hand tighten bolts.
4. Align the front cover and tighten the bolts. Install a new front seal and reinstall any removed components.
This document provides instructions for disassembling and assembling a final drive for 330F and 330F LN excavators. The disassembly procedure involves using various tools to remove 37 individual parts from the final drive assembly, including gears, shafts, housings, seals and bearings. The assembly procedure consists of 30 steps to reinstall the parts in reverse order, noting the proper application of sealants and adjustment of bearing preload using shims. Precise alignment and cleanliness of parts is emphasized throughout.
Caterpillar Cat 330D2 L Excavator (Prefix FEX) Service Repair Manual (FEX0000...dujkdksmdmdm
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
Caterpillar Cat 330D2 L Excavator (Prefix EBP) Service Repair Manual (EBP0000...dujkdksmdmdm
The document provides disassembly instructions for a 330D2 and 330D2 L excavator travel motor in 28 steps. It begins by having the technician thoroughly clean and secure the travel motor vertically before disassembling. The steps then carefully describe removing components like the head, brake piston, plates, seals, bearings, and more. Pictures accompany each step to illustrate the proper procedure. Safety notices are included to handle fluids and springs carefully.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves removing 37 individual parts in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on setting the bearing preload and installing seals correctly.
The document provides instructions for disassembling an excavator travel motor. It is a 27 step process that includes removing the motor head, brake piston, barrel assembly, cam plate, and other internal components. Special tools are required to properly support and disassemble the motor. Technicians are advised to take care to contain fluids and properly dispose of them.
The document provides instructions for disassembling a final drive component in 3 steps:
1. Remove the final drive assembly and disassemble it by removing the cover, gears, carrier assembly, planetary gears, and ring gear.
2. Disassemble the planetary carrier by removing the shafts, washers, bearings and gears.
3. Remove the ring gear from the sprocket housing, then disassemble the motor housing by removing bolts, shims and a coupling gear.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual (R2D00001...dujkdksmdmdm
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Installation requires matching dimensions and orientations when pressing in new bearings and reinstalling components.
To remove the flywheel, bolts are first removed 180 degrees apart using a guide stud before lifting the flywheel off. Installation involves heating and pressing in a ring gear, lifting the flywheel into place using guide studs, and torquing bolts to the specified value
More Related Content
Similar to Caterpillar Cat 330F LN Excavator (Prefix JFR) Service Repair Manual (JFR00001 and up).pdf
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f excavator (prefix jhf) service repair manual (jhf00001 ...dfjjsjkemmm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...idkkdmmd
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise measurements and torque specifications are provided to ensure correct assembly.
Caterpillar Cat 330F L Excavator (Prefix JHF) Service Repair Manual (JHF00001...f8uejkkdmdm8u
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar Cat 330F L Excavator (Prefix JHF) Service Repair Manual (JHF00001...8ufjsekddm8u
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...dfjjsjkemmm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. The disassembly procedure involves using various tools to remove over 30 individual parts in a specific sequence. The assembly procedure similarly provides step-by-step instructions to reinstall the parts in reverse order, noting the importance of cleaning, applying sealants, and properly setting bearing preloads.
Caterpillar cat 330 f ln excavator (prefix jhf) service repair manual (jhf000...ikdkdmdm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Similar to Caterpillar Cat 330F LN Excavator (Prefix JFR) Service Repair Manual (JFR00001 and up).pdf (12)
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...dujkdksmdmdm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, and remove the front cover and gasket.
3. Clean the front cover, housing, and install a new gasket. Use guide studs to position the front cover and hand tighten bolts.
4. Align the front cover and tighten the bolts. Install a new front seal and reinstall any removed components.
This document provides instructions for disassembling and assembling a final drive for 330F and 330F LN excavators. The disassembly procedure involves using various tools to remove 37 individual parts from the final drive assembly, including gears, shafts, housings, seals and bearings. The assembly procedure consists of 30 steps to reinstall the parts in reverse order, noting the proper application of sealants and adjustment of bearing preload using shims. Precise alignment and cleanliness of parts is emphasized throughout.
Caterpillar Cat 330D2 L Excavator (Prefix FEX) Service Repair Manual (FEX0000...dujkdksmdmdm
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
Caterpillar Cat 330D2 L Excavator (Prefix EBP) Service Repair Manual (EBP0000...dujkdksmdmdm
The document provides disassembly instructions for a 330D2 and 330D2 L excavator travel motor in 28 steps. It begins by having the technician thoroughly clean and secure the travel motor vertically before disassembling. The steps then carefully describe removing components like the head, brake piston, plates, seals, bearings, and more. Pictures accompany each step to illustrate the proper procedure. Safety notices are included to handle fluids and springs carefully.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves removing 37 individual parts in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on setting the bearing preload and installing seals correctly.
The document provides instructions for disassembling an excavator travel motor. It is a 27 step process that includes removing the motor head, brake piston, barrel assembly, cam plate, and other internal components. Special tools are required to properly support and disassemble the motor. Technicians are advised to take care to contain fluids and properly dispose of them.
The document provides instructions for disassembling a final drive component in 3 steps:
1. Remove the final drive assembly and disassemble it by removing the cover, gears, carrier assembly, planetary gears, and ring gear.
2. Disassemble the planetary carrier by removing the shafts, washers, bearings and gears.
3. Remove the ring gear from the sprocket housing, then disassemble the motor housing by removing bolts, shims and a coupling gear.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual (R2D00001...dujkdksmdmdm
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Installation requires matching dimensions and orientations when pressing in new bearings and reinstalling components.
To remove the flywheel, bolts are first removed 180 degrees apart using a guide stud before lifting the flywheel off. Installation involves heating and pressing in a ring gear, lifting the flywheel into place using guide studs, and torquing bolts to the specified value
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...dujkdksmdmdm
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Removing hydraulic hoses and fittings, separating the track, and using a lever puller and vacuum pump to remove the assembly.
2. Lifting the assembly free using lifting brackets and bolts, and removing mounting bolts and seals.
3. Reinstalling seals and components in reverse order, and refilling the hydraulic system. Proper cleaning, safety procedures, and use of anti-seize compound are emphasized.
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual (JLP00001...dujkdksmdmdm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts before disassembly and have additional assistance when removing heavy components weighing over 30kg. The detailed process takes the final drive completely apart down to individual planetary gears and shafts.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...dujkdksmdmdm
The document provides instructions for assembling and installing the swing drive of an excavator. It describes 30 steps for assembling the internal components of the swing drive, including installing bearings, gears, seals, and housing components. It then describes 6 steps for installing the entire assembled swing drive into the excavator frame, including attaching lifting brackets, applying sealant, tightening bolts to the specified torque, and filling it with oil. The overall process installs and secures the fully assembled swing drive subsystem into the excavator.
Caterpillar Cat 330D L Excavator (Prefix ERN) Service Repair Manual (ERN00001...dujkdksmdmdm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive including removing covers, gears, carriers, shafts, seals and housings. Special tools are required including link brackets and forcing bolts to remove components due to their weight, with some parts weighing up to 550kg. Detailed illustrations accompany each step to show how to disassemble the various components.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...dujkdksmdmdm
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the proper sequence for installing mounting bolts are also included.
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key components that are disassembled include the drive housing, three planetary gear assemblies, carrier assemblies, ring gear, and other internal gears, shafts, seals and bearings. Special tools are required for pressing, pulling, and removing components. Proper lifting devices and safety precautions are noted due to the heavy weights of components ranging from 32 to 550 kg.
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like link brackets, forcing bolts, and presses. Cleanliness is important to prevent dirt from entering during reassembly.
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
The document provides instructions for assembling and installing the swing drive of an excavator. It describes applying sealant and installing bearings, gears, housings, and other components in the proper order and orientation. Bolts are tightened to the specified torque using an impact wrench. The completed swing drive is then installed on the excavator frame and filled with oil.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR JFR
Configuration: 330F & 330F LN Excavators JFR00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326F, 329F and 330F Excavators Machine Systems
Media Number -UENR3313-07 Publication Date -01/09/2015 Date Updated -12/09/2018
i05436085
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 138-7575 Link Bracket 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G 138-7576 Link Bracket 2
H 154-6181 Forcing Screw 3
Start By:
a. Remove the final drive.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled to the original locations.
1/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00892878
2. Use Tooling (G) and a suitable lifting device to position the final drive assembly onto
Tooling (A). The weight of the final drive assembly is approximately 550 kg (1200 lb).
3. Remove bolts (1).
Illustration 2 g00892883
4. Use Tooling (B) and a suitable lifting device to remove cover (2). The weight of cover (2) is
approximately 32 kg (70 lb).
Illustration 3 g00892888
2/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 5. Remove bolts (3) and gear (4). Check plate (6). Replace plate (6) if plate (6) is worn.
Remove plugs (5) from cover (2).
Illustration 4 g00892906
6. Remove O-ring seals (7) from plugs (5).
Illustration 5 g00892930
7. Remove gear (8) and spacer (9).
Illustration 6 g00892965
3/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 8. Use Tooling (C) to remove retaining ring (10). Remove washer (11) and gear (12). Remove
bearing assembly (13) and washer (14).
9. Repeat Step 8 for the other two gear assemblies.
Illustration 7 g00892968
10. Remove retaining ring (15).
Illustration 8 g00892975
11. Remove carrier assembly (16).
4/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 9 g02408860
12. Use a suitable press to remove the shafts from carrier assembly (16).
Illustration 10 g00892977
13. Remove gear (17) and spacer (18).
Illustration 11 g00892997
5/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 14. Use Tooling (D) and a suitable lifting device to remove planetary carrier (19). The weight of
planetary carrier (19) is approximately 48 kg (105 lb).
Illustration 12 g00893019
15. Remove retaining ring (21). Lift planetary carrier (19) off sun gear (20).
Illustration 13 g00896860
16. Drive spring pin (23) into planetary shaft (22).
Illustration 14 g00893043
6/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. 17. Remove planetary shaft (22). Use a suitable punch to remove spring pin (23) from planetary
shaft (22).
Illustration 15 g00896863
18. Remove washers (24) and bearing (25) from planetary gear (26).
19. Repeat Steps 16 through 18 for the other two planetary gears.
Illustration 16 g01842853
20. Remove gear (27). Remove spacer (27A).
Illustration 17 g01842974
7/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 21. Use two people to remove carrier assembly (28). The weight of carrier assembly (28) is
approximately 38 kg (85 lb).
Illustration 18 g01843140
22. Drive spring pin (30) into shaft (29).
Illustration 19 g00893658
23. Remove shaft (29). Use a suitable punch to remove spring pin (30) from shaft (29).
Illustration 20 g00893674
24. Remove washers (31) and bearings (32) from planetary gear (33).
8/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. 25. Repeat Steps 22 through 24 for the other three planetary gears.
Illustration 21 g01208300
26. Fasten Tooling (E) and a suitable lifting device to ring gear (34), as shown. Remove ring
gear (34) from sprocket housing (35). The weight of ring gear (34) is approximately 66 kg
(146 lb).
Illustration 22 g01208542
27. Remove O-ring seal (36) from sprocket housing (35).
Illustration 23 g01208553
9/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 28. Remove bolts (37) from coupling gear (38).
Illustration 24 g03431447
29. Install Tooling (H) in coupling gear (38). Tighten the Tooling (H) evenly in order to loosen
coupling gear (38). Remove the coupling gear from the motor housing.
Illustration 25 g01208578
Illustration 26 g01208625
30. Remove shims (40) from the motor housing.
10/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Note: Inner cones and outer bearing cones (42) and (44) are a slip fit on the motor housing.
While you remove sprocket housing (35) from the motor housing, inner bearing cone (42)
and outer bearing cones (44) may stay with the sprocket housing or the inner bearing cone
may stay on the motor housing.
31. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Separate the
sprocket housing from the motor housing. The weight of sprocket housing (35) is
approximately 109 kg (240 lb).
Illustration 27 g01208626
32. Remove the locating pins from the motor housing.
33. Remove Duo-Cone seal (41) from the motor housing.
34. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.
Illustration 28 g03431456
35. Remove Duo-Cone seal (43) from the sprocket housing.
36. If outer bearing cone (44) remained on the sprocket housing, then remove the outer bearing
cone.
37. Remove the bearing cups from the sprocket housing.
11/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR JFR
Configuration: 330F & 330F LN Excavators JFR00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326F, 329F and 330F Excavators Machine Systems
Media Number -UENR3313-07 Publication Date -01/09/2015 Date Updated -12/09/2018
i07332931
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Stand Group 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 138-7575 Link Bracket 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G
8T-9206 Duo-Cone Seal Installer As 1
169-0503 Installation Kit 1
H - Loctite C5A Copper Antiseize -
J - Loctite 242 Threadlocker -
K - Loctite Highflex GM -
L FT-2770 Leak down Test Tool 1
1. Make sure that all parts of the final drive are thoroughly clean and free of dirt and debris
prior to assembly. Check the condition of all O-ring seals that are used in the final drive. If
any of the seals are damaged, use new parts for replacement. Reassemble the final drive on
Tooling (A).
1/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 1 g03431464
Note: New final drives are equipped with angular contact ball bearings.
2. Apply Tooling (H) to the surfaces inside sprocket housing (35) that contacts the bearing
cups. Install a bearing cup that is in each side of the sprocket housing with a press. Make
sure that the bearing cups are properly seated.
3. Apply Tooling (H) to the surfaces inside the sprocket housing that contacts bearing cones
(44).
4. Install outer bearing cone (44) in the sprocket housing.
Illustration 2 g01208625
5. Attach Tooling (F) and a suitable lifting device to sprocket housing (35). The weight of
sprocket housing (35) is approximately 109 kg (240 lb). Install sprocket housing (35) on the
motor housing. Carefully install inner bearing cone (42) on the sprocket housing.
2/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 3 g01208578
6. Adjust the bearing preload of the final drive. Determine the correct number of shims (40)
that are required for the proper bearing preload, as follows:
Note: New final drives are equipped with angular contact ball bearings that require pre-load
like the old roller bearings.
Illustration 4 g01208987
a. Use a depth micrometer to measure the step height of coupling gear (38) at several
locations around the gear. Find the average for the measured dimensions around the
gear and record the dimension. Call this Dimension (X).
b. Apply a load of 4000 kg (8820 lb) to the bearing cones.
c. Rotate sprocket housing (35) several times to seat the bearing cones.
d. Reduce the load to 1000 ± 100 kg (2205 ± 220 lb).
3/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 5 g00631001
e. With the bearing cones loaded, measure the distance between the top face of the
motor housing and the top face of the bearing cone. Take measurements in several
locations around the motor housing. Find the average of the measured dimensions,
and record the dimensions. Call this Dimension (Y).
f. Determine the correct thickness of the shims which are used between the bearing
cones and the coupling gear . Use the following equation to determine the shim pack
thickness.
Shim pack thickness ... (Y) − (X) ± 0.05 mm (0.002 inch)
Note: If two shims are required, install the thinnest shim next to the coupling gear
during final assembly.
Illustration 6 g03431699
7. Attach Tooling (F) and a suitable lifting device to sprocket housing (35). Separate sprocket
housing (35) from the motor housing.
Reference: Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contacts the seals must be clean and dry. After
installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal seals.
4/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 7 g00631006
Illustration 8 g01208999
8. Use Tooling (G) to install Duo-Cone seal (43) in the sprocket housing.
Illustration 9 g00631014
5/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 10 g03431475
9. Use Tooling (G) to install Duo-Cone seal (41) in the motor housing.
10. Apply Tooling (H) in the bores for the locating pins that are in the motor housing. Reinstall
the locating pins in the motor housing.
Illustration 11 g01208625
11. Make sure that inner bearing cone (42) is seated properly on the motor housing.
Note: Do not scratch Duo-Cone seal (41) or damage the Duo-Cone seal in the main
housing, or the motor housing during assembly of the two components. After installation of
the main housing on the motor housing, there will be a small gap between the components.
The gap between the components is caused by the Duo-Cone seal. The gap will be
eliminated during the installation of the coupling gear .
12. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Carefully install
the sprocket housing on the motor housing.
13. Install the outer bearing cone on the sprocket housing. Make sure that the outer bearing cone
is properly seated.
6/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 12 g01208578
14. Install shims (40) that were determined in Steps 6.a through 6.f on the end of the sprocket
housing. If shims were required, make sure that the thinnest shim is installed on top.
Illustration 13 g01208553
15. Put coupling gear (38) in the original position on the motor housing.
16. Apply Tooling (J) on the threads of bolts (37) that hold coupling gear (38) in position.
Tighten bolts (37) evenly and tighten the bolts in diagonally opposite pairs to a torque of
570 ± 80 N·m (420 ± 60 lb ft).
Illustration 14 g01208542
7/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 17. Install O-ring seal (36) in sprocket housing (35).
Illustration 15 g01208300
18. Thoroughly clean the mating surface of sprocket housing (35) that contacts ring gear (34).
19. Apply a bead of Tooling (K) on the mating surface of ring gear (34).
20. Attach Tooling (E) and a suitable lifting device to ring gear (34). Put ring gear (34) in
position on the sprocket housing. The weight of ring gear (34) is approximately 66 kg
(146 lb). Make sure that the alignment mark upon the sprocket housing and the ring gear
line with each other.
Illustration 16 g01843479
8/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 17 g00893674
21. Assemble carrier assembly (28), as follows.
a. Install bearings (32) in planetary gear (33).
b. Install thrust washers (31) and planetary gear (33) in the carrier assembly.
c. Use a deburring tool to remove the metal burr from the openings in the carrier. Install
planetary shaft (29) in the carrier assembly.
d. Drive spring pin (30) into planetary shaft (29).
Illustration 18 g00941047
The stake mark is at position (S).
e. Orient the split in spring pin (30) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 2.25 ± 0.75 mm
(0.089 ± 0.030 inch) from the outside diameter of the spring pin hole.
22. Repeat Steps 21.a through 21.e to install the other two planetary gears in the carrier
assembly.
9/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 19 g01842974
23. Use two people to install carrier assembly (28). The weight of carrier assembly (28) is
approximately 38 kg (85 lb).
Illustration 20 g01842853
24. Install spacer (27A). Install gear (27).
Illustration 21 g00897548
10/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 22 g00896863
25. Assemble planetary carrier (19), as follows.
a. Install bearing (25) in planetary gear (26).
b. Install thrust washers (24) and planetary gear (26) in the planetary carrier.
c. Use a deburring tool to remove the metal burr from the openings in the carrier. Install
planetary shaft (22) in planetary carrier (19).
d. Drive spring pin (23) into planetary shaft (22).
Illustration 23 g00941047
The stake mark is at position (S).
e. Orient the split in spring pin (23) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 2.25 ± 0.75 mm
(0.089 ± 0.030 inch) from the outside diameter of the spring pin hole.
f. Repeat Steps 25.a through 25.e to install the other two planetary gears in the carrier.
11/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 24 g00893019
26. Position sun gear (20) in planetary carrier (19) and install retaining ring (21).
Illustration 25 g00892997
27. Use Tooling (D) and a suitable lifting device to install planetary carrier (19) into gear (34).
The weight of planetary carrier (19) is approximately 48 kg (105 lb).
Illustration 26 g00892977
28. Install spacer (18) and gear (17).
12/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 27 g01389807
Note: Make sure that the oil passages in the shafts are oriented toward the center of carrier
assembly (16).
29. Raise the temperature of carrier assembly (16). Lower the temperature of the shafts. Install
the shafts into carrier assembly (16) until the groove of the shafts is at Dimension (A).
Dimension (A) equals 25.00 ± 0.10 mm (0.984 ± 0.004 inch).
30. Make eight stake marks at distance of Dimension (C) from each shaft. Dimension (C)
equals 2.0 ± 1.0 mm (0.08 ± 0.04 inch). The width of each stake mark should be equal to
Dimension (B). Dimension (B) equals 4.0 ± 1.0 mm (0.16 ± 0.04 inch).
Illustration 28 g00892975
13/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. 31. Install carrier assembly (16).
Illustration 29 g00892968
32. Install retaining ring (15).
Illustration 30 g00892965
33. Install washer (14) and bearing assembly (13). Install gear (12) and washer (11). Use
Tooling (C) to install retaining ring (10).
34. Repeat Step 33 for the other two planetary gears.
Illustration 31 g00780428
14/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...