This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
Caterpillar cat 326 d2 l excavator (prefix kgy) service repair manual (kgy000...fjsjekkmdmme
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavators. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, friction discs, and seals. The assembly procedure instructs putting the travel motor back together and notes that all O-rings and gaskets must be replaced and components should be cleaned before assembly. Proper alignment of parts is important during assembly.
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavators. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, friction discs, and seals. The assembly procedure instructs putting the travel motor back together in the reverse order and notes the importance of cleanliness, applying lubricant to parts, and ensuring correct alignment of components.
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the head, bearings, brake piston, seals, and housing cover. Corresponding assembly instructions are also provided, including applying thread lock compound and ensuring proper alignment of parts. Cleanliness is emphasized throughout the process.
Caterpillar cat 326 d2 l excavator (prefix mgw) service repair manual (mgw000...fjjskdmnenemm
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the head, port plate, bearings, brake piston, seals, plates, springs and retaining rings. Corresponding assembly instructions are also provided, including applying thread lock compound and ensuring proper alignment of keys and notches. Cleanliness is emphasized throughout the process.
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove and install over 25 components of the travel motor. Cleanliness is emphasized during disassembly and assembly. Several components, like pistons and springs, must be returned to their original positions.
Fiat Kobelco SL30B Skid Steer Loader Service Repair Manual.pdfprmy389342
This document is the service manual for an SL30B skid steer loader. It provides safety precautions and instructions for operating and servicing the loader. Some key points:
- The manual outlines many safety rules for operating the loader safely, such as wearing protective equipment, not allowing passengers, and ensuring all equipment is lowered before servicing.
- It provides standard torque specifications for various types of hardware including decimal, metric, and hydraulic fittings to ensure correct tightening of components.
- The manual is organized into tabs covering general information, engines, fuel system, electrical systems, power train, hydraulics, and mounted equipment. Each tab contains an index of relevant sections.
- Sections provide instructions
Fiat Kobelco EX95W Mini Wheel Excavator Service Repair Manual.pdfprmy389342
This document provides safety precautions for operating an excavator. It advises reading the operator's manual carefully before starting or using the machine. Operators should be familiar with all safety signs and their meanings. Only authorized personnel should operate the machine. Personal protective equipment such as hard hats and safety glasses should always be worn. The operator's compartment and controls should be kept clean. Operators should not jump on or off the machine and should keep hands and feet inside the cab at all times. The machine should come to a complete stop before the operator exits. Height, width and weight limitations of the work site must be assessed. Underground utilities should be located and marked before digging.
Daewoo Doosan DE12TIS Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Caterpillar cat 326 d2 l excavator (prefix kgy) service repair manual (kgy000...fjsjekkmdmme
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavators. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, friction discs, and seals. The assembly procedure instructs putting the travel motor back together and notes that all O-rings and gaskets must be replaced and components should be cleaned before assembly. Proper alignment of parts is important during assembly.
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavators. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, friction discs, and seals. The assembly procedure instructs putting the travel motor back together in the reverse order and notes the importance of cleanliness, applying lubricant to parts, and ensuring correct alignment of components.
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the head, bearings, brake piston, seals, and housing cover. Corresponding assembly instructions are also provided, including applying thread lock compound and ensuring proper alignment of parts. Cleanliness is emphasized throughout the process.
Caterpillar cat 326 d2 l excavator (prefix mgw) service repair manual (mgw000...fjjskdmnenemm
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the head, port plate, bearings, brake piston, seals, plates, springs and retaining rings. Corresponding assembly instructions are also provided, including applying thread lock compound and ensuring proper alignment of keys and notches. Cleanliness is emphasized throughout the process.
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove and install over 25 components of the travel motor. Cleanliness is emphasized during disassembly and assembly. Several components, like pistons and springs, must be returned to their original positions.
Fiat Kobelco SL30B Skid Steer Loader Service Repair Manual.pdfprmy389342
This document is the service manual for an SL30B skid steer loader. It provides safety precautions and instructions for operating and servicing the loader. Some key points:
- The manual outlines many safety rules for operating the loader safely, such as wearing protective equipment, not allowing passengers, and ensuring all equipment is lowered before servicing.
- It provides standard torque specifications for various types of hardware including decimal, metric, and hydraulic fittings to ensure correct tightening of components.
- The manual is organized into tabs covering general information, engines, fuel system, electrical systems, power train, hydraulics, and mounted equipment. Each tab contains an index of relevant sections.
- Sections provide instructions
Fiat Kobelco EX95W Mini Wheel Excavator Service Repair Manual.pdfprmy389342
This document provides safety precautions for operating an excavator. It advises reading the operator's manual carefully before starting or using the machine. Operators should be familiar with all safety signs and their meanings. Only authorized personnel should operate the machine. Personal protective equipment such as hard hats and safety glasses should always be worn. The operator's compartment and controls should be kept clean. Operators should not jump on or off the machine and should keep hands and feet inside the cab at all times. The machine should come to a complete stop before the operator exits. Height, width and weight limitations of the work site must be assessed. Underground utilities should be located and marked before digging.
Daewoo Doosan DE12TIS Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12TI Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12T Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12 Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfprmy389342
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, listed with their part numbers and the quantity required. Key components included are the power unit enclosure, rear doors, covers, fasteners, and guards. The parts are organized with an index and diagram to allow technicians to easily find replacement parts.
Crown LP3020 Lift Truck Service Repair Manual.pdfprmy389342
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes overview diagrams of truck components, inspection and maintenance schedules, repair procedures, and part replacement instructions. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown LP3010 Lift Truck Service Repair Manual.pdfprmy389342
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes safety notes, inspection and maintenance schedules, repair and replacement procedures, and diagrams. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown GPC2000 Series Lift Truck Parts Catalogue Manual.pdfprmy389342
This document provides lubrication information for a parts manual. It lists the recommended lubricants and their specifications for various components of the product. Grease type 2 is recommended for bearings and grease type 2-P for ball bearings. Mobilex 00-200 is suitable for lower operating temperatures, while Mobilex 005-200 is recommended for higher temperatures.
Clark TMX12-25 Forklift Service Repair Manual.pdfprmy389342
This document provides instructions for safely maintaining electric forklifts. It discusses:
1. Identifying safety signs and messages and outlining safe maintenance practices such as blocking the wheels, disconnecting batteries, and checking for fuel leaks before working.
2. Procedures for lifting parts of the forklift like the drive wheels or rear, including using blocks and jacks of adequate capacity.
3. Chain securing an upright carriage when raised and shipping tie-down instructions.
Clark EPX 16-20S Forklift Service Repair Manual.pdfprmy389342
This document provides instructions for safely maintaining electric forklifts. It discusses:
1. Identifying safety signs and messages in the manual and on trucks to understand hazards.
2. Recommended safe maintenance practices such as properly ventilating work areas, using fire protection equipment, and disconnecting batteries before working on electrical systems.
3. Procedures for safely lifting, jacking, and blocking forklifts, including raising the drive wheels, upright, and entire truck, to access components for repair work.
Clark CMP 70 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark CMP 60 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark CMP 50 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Caterpillar Cat D400E II EJECTOR TRUCK (Prefix APF) Service Repair Manual (AP...prmy389342
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a D400E II Ejector Truck with a 3406E engine. The procedures describe draining fluids, using various specialty tools to compress springs, extract components, and properly position replacement parts. Safety notices warn of potential injury from compressed springs and ensure cleanliness when handling engine parts.
This document provides instructions for disassembling a piston pump used in Caterpillar articulated trucks. The pump is removed from the machine and various internal components are then dismantled. These components include pressure and flow compensator valves, springs, seals, pistons, barrels and housings. Detailed illustrations accompany each step to show how to access fasteners and position parts for removal or disassembly. Safety notices are also included regarding contained fluids and released spring forces during the process. The overall document provides a technical service manual excerpt on thoroughly disassembling a hydraulic pump assembly.
This document provides instructions for removing and installing a piston pump and pump control valve on a 725 Articulated Truck. It outlines 37 steps to disassemble the piston pump, checking components for wear, lubricating seals, and precisely adjusting preload on bearings. It then describes 4 steps to install the piston pump and connect hoses. Finally, it warns of hot hydraulic fluid and outlines 1 step to remove the pump control valve by marking all lines for identification during reinstallation.
Caterpillar Cat 336F L Excavator (Prefix YFD) Service Repair Manual (YFD00001...prmy389342
This document provides instructions for disassembling the travel motor on a 336F excavator. It involves removing over 30 components in 27 steps, including the motor head assembly, piston assemblies, barrel assembly, swashplate, and various seals and plates. Tools required include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Daewoo Doosan DE12TI Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12T Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12 Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfprmy389342
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, listed with their part numbers and the quantity required. Key components included are the power unit enclosure, rear doors, covers, fasteners, and guards. The parts are organized with an index and diagram to allow technicians to easily find replacement parts.
Crown LP3020 Lift Truck Service Repair Manual.pdfprmy389342
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes overview diagrams of truck components, inspection and maintenance schedules, repair procedures, and part replacement instructions. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown LP3010 Lift Truck Service Repair Manual.pdfprmy389342
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes safety notes, inspection and maintenance schedules, repair and replacement procedures, and diagrams. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown GPC2000 Series Lift Truck Parts Catalogue Manual.pdfprmy389342
This document provides lubrication information for a parts manual. It lists the recommended lubricants and their specifications for various components of the product. Grease type 2 is recommended for bearings and grease type 2-P for ball bearings. Mobilex 00-200 is suitable for lower operating temperatures, while Mobilex 005-200 is recommended for higher temperatures.
Clark TMX12-25 Forklift Service Repair Manual.pdfprmy389342
This document provides instructions for safely maintaining electric forklifts. It discusses:
1. Identifying safety signs and messages and outlining safe maintenance practices such as blocking the wheels, disconnecting batteries, and checking for fuel leaks before working.
2. Procedures for lifting parts of the forklift like the drive wheels or rear, including using blocks and jacks of adequate capacity.
3. Chain securing an upright carriage when raised and shipping tie-down instructions.
Clark EPX 16-20S Forklift Service Repair Manual.pdfprmy389342
This document provides instructions for safely maintaining electric forklifts. It discusses:
1. Identifying safety signs and messages in the manual and on trucks to understand hazards.
2. Recommended safe maintenance practices such as properly ventilating work areas, using fire protection equipment, and disconnecting batteries before working on electrical systems.
3. Procedures for safely lifting, jacking, and blocking forklifts, including raising the drive wheels, upright, and entire truck, to access components for repair work.
Clark CMP 70 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark CMP 60 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark CMP 50 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Caterpillar Cat D400E II EJECTOR TRUCK (Prefix APF) Service Repair Manual (AP...prmy389342
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a D400E II Ejector Truck with a 3406E engine. The procedures describe draining fluids, using various specialty tools to compress springs, extract components, and properly position replacement parts. Safety notices warn of potential injury from compressed springs and ensure cleanliness when handling engine parts.
This document provides instructions for disassembling a piston pump used in Caterpillar articulated trucks. The pump is removed from the machine and various internal components are then dismantled. These components include pressure and flow compensator valves, springs, seals, pistons, barrels and housings. Detailed illustrations accompany each step to show how to access fasteners and position parts for removal or disassembly. Safety notices are also included regarding contained fluids and released spring forces during the process. The overall document provides a technical service manual excerpt on thoroughly disassembling a hydraulic pump assembly.
This document provides instructions for removing and installing a piston pump and pump control valve on a 725 Articulated Truck. It outlines 37 steps to disassemble the piston pump, checking components for wear, lubricating seals, and precisely adjusting preload on bearings. It then describes 4 steps to install the piston pump and connect hoses. Finally, it warns of hot hydraulic fluid and outlines 1 step to remove the pump control valve by marking all lines for identification during reinstallation.
Caterpillar Cat 336F L Excavator (Prefix YFD) Service Repair Manual (YFD00001...prmy389342
This document provides instructions for disassembling the travel motor on a 336F excavator. It involves removing over 30 components in 27 steps, including the motor head assembly, piston assemblies, barrel assembly, swashplate, and various seals and plates. Tools required include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326D2 EXCAVATOR KGY
Configuration: 326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03124522
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded RodM12 x 1.75 by 250 mm (10 in) long 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove".
1/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
2/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00887302
6. Remove O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 3 g00887311
7. Remove O-ring seals (6) . Remove springs (7) .
3/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B) .
8. Place a shop towel over brake piston (8) . Retain brake piston (8) with Tooling (B) . Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y) . Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
4/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g00887336
9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
11. Remove plates (13) and friction discs (14) .
Illustration 8 g00887401
5/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 9 g00887405
12. Install Tooling (C) into shaft (15) . Use a prybar to remove the rotating assembly (16) from
the housing.
13. Remove Tooling (C) from shaft (15) .
Illustration 10 g00887424
14. Remove shaft (15) from rotating assembly (16) .
6/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 11 g00887426
15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15) .
Illustration 12 g00887445
16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
Illustration 13 g00887463
17. Rotate shaft (15) . Install shaft (15) into a suitable press. Install Tooling (E) . Remove
bearing race (19) from shaft (15) .
7/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 14 g00887501
18. Remove cam plate (20) from barrel assembly (21) .
Illustration 15 g00887520
19. Remove piston assemblies and retainer plate (22) from barrel assembly (21) .
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
8/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 16 g00887558
20. Remove ball (23) and springs (24) .
Illustration 17 g00887578
21. Remove bearing (25) .
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27) .
24. Remove seal (28) .
9/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g00887619
25. Remove bolts (29) and cover (30) .
Illustration 20 g00887729
26. Remove seal (31) and backup ring (32) .
Illustration 21 g00887754
27. Remove piston actuator (33) and seal (34) .
10/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 ...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 22 g00887762
28. Remove O-ring seal (35) from the housing of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 18:55:52 UTC+0800 2020
11/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 ...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326D2 EXCAVATOR KGY
Configuration: 326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03124523
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded Rod M12 x 1.75 X 250 mm (10 in) long 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G 9S-3263 Thread Lock Compound -
Note: Replace all O-ring seals and gaskets. Apply a light film of"10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause trouble later. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
1/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33) .
2/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00887729
3. Install backup ring (32) and seal (31) .
Illustration 4 g00887619
4. Install cover (30) and bolts (29) . Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
3/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 5. Apply Tooling (G) to the mating surface of seal (28) . Use Tooling (E) in order to install
seal (28) .
6. Use Tooling (F) in order to install retaining ring (27) .
Illustration 6 g00887578
7. Rotate the housing.
8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25) .
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
4/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 10. Install springs (24) into the barrel. Install ball (23) onto springs (24) .
Illustration 8 g00887520
11. Install piston assemblies and retainer plate (22) into barrel assembly (21) .
Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Install cam plate (20) onto barrel assembly (21) .
5/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15) .
Illustration 11 g00887426
14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15) .
Illustration 12 g00888710
6/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 15. Install bearing race (18) onto shaft (15) .
Note: Bearing race (18) must contact retaining ring (17) .
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15) . Install shaft (15) into rotating assembly (16) .
17. Place the pump housing into Tooling (A) .
Illustration 14 g00887401
18. Use Tooling (C) in order to install rotating assembly (16) into the housing.
7/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 15 g00887501
Illustration 16 g00887578
19. The notches in cam plate (20) must align with keys (26) . The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
20. Install plates (13) and friction discs (14) into the housing.
8/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8) .
24. Install brake piston (8) into the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level in
order to prevent damage to the O-ring seals.
9/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6) .
Illustration 21 g00887302
26. Install O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 22 g00887295
27. Install head (2) onto the body of the travel motor.
10/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 ...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1) . Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By: Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 18:56:48 UTC+0800 2020
11/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 ...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326D2 EXCAVATOR KGY
Configuration: 326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03808350
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded Rod 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/4
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g00878123
2. Install new O-ring seal (6) . Apply clean hydraulic oil on the O-ring seal.
Illustration 2 g00707267
3. Attach a suitable lifting device to travel motor (4) , as shown.
4. The weight of the travel motor is approximately 57 kg (125 lb).
Illustration 3 g00878121
2/4
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. 5. Carefully install travel motor (4) onto Tooling (A) . Slide the travel motor into the final
drive.
6. Install one of three bolts (5) that secures the travel motor to the final drive.
7. Remove Tooling (A) .
Illustration 4 g00707275
Typical example
8. Install remaining bolts (2) .
9. Connect hose assembly (3) . Connect hose assembly (1) .
10. Fill the final drive with oil.
ReferenceRefer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
ReferenceRefer to Operation and Maintenance Manual, "Final Drive Oil Level - Check" for
the correct filling procedure.
11. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
12. Obtain a hydraulic oil sample from the main S·O·S port.
ReferenceRefer to Operation and Maintenance Manual, "Sampling Interval and Location of
Sampling Valve" for the correct location.
13. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system.
ReferenceRefer to Contamination Control Guidelines, SEBF8436, "Hydraulic System
Flushing Procedure for 322C Hydraulic Excavators" for further information.
3/4
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. End By: Install the travel brake valve. Refer to Disassembly and Assembly, "Travel Brake Valve
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 18:57:43 UTC+0800 2020
4/4
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326D2 EXCAVATOR KGY
Configuration: 326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i05453056
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C
154-6184 Forcing Bolt (M 20) 2
154-6185(1)
Forcing Bolt (M 24) 2
(1)
For Use on 329 and 330 sales models
Start By:
a. Separate the track assembly.
b. Remove the travel motor.
1/3
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...