This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavator models. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, seals, and housing cover. Corresponding assembly instructions are also provided and specify cleaning and lubricating parts, as well as torques for certain bolts. Safety notices are included regarding spring force and cleanliness during the repair process.
Caterpillar cat 326 d2 l excavator (prefix kgy) service repair manual (kgy000...fjsjekkmdmme
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavators. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, friction discs, and seals. The assembly procedure instructs putting the travel motor back together and notes that all O-rings and gaskets must be replaced and components should be cleaned before assembly. Proper alignment of parts is important during assembly.
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavators. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, friction discs, and seals. The assembly procedure instructs putting the travel motor back together in the reverse order and notes the importance of cleanliness, applying lubricant to parts, and ensuring correct alignment of components.
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the head, bearings, brake piston, seals, and housing cover. Corresponding assembly instructions are also provided, including applying thread lock compound and ensuring proper alignment of parts. Cleanliness is emphasized throughout the process.
Caterpillar cat 326 d2 l excavator (prefix mgw) service repair manual (mgw000...fjjskdmnenemm
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the head, port plate, bearings, brake piston, seals, plates, springs and retaining rings. Corresponding assembly instructions are also provided, including applying thread lock compound and ensuring proper alignment of keys and notches. Cleanliness is emphasized throughout the process.
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove and install over 25 components of the travel motor. Cleanliness is emphasized during disassembly and assembly. Several components, like pistons and springs, must be returned to their original positions.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
Caterpillar cat 326 d2 l excavator (prefix kgy) service repair manual (kgy000...fjsjekkmdmme
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavators. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, friction discs, and seals. The assembly procedure instructs putting the travel motor back together and notes that all O-rings and gaskets must be replaced and components should be cleaned before assembly. Proper alignment of parts is important during assembly.
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavators. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, friction discs, and seals. The assembly procedure instructs putting the travel motor back together in the reverse order and notes the importance of cleanliness, applying lubricant to parts, and ensuring correct alignment of components.
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the head, bearings, brake piston, seals, and housing cover. Corresponding assembly instructions are also provided, including applying thread lock compound and ensuring proper alignment of parts. Cleanliness is emphasized throughout the process.
Caterpillar cat 326 d2 l excavator (prefix mgw) service repair manual (mgw000...fjjskdmnenemm
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the head, port plate, bearings, brake piston, seals, plates, springs and retaining rings. Corresponding assembly instructions are also provided, including applying thread lock compound and ensuring proper alignment of keys and notches. Cleanliness is emphasized throughout the process.
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove and install over 25 components of the travel motor. Cleanliness is emphasized during disassembly and assembly. Several components, like pistons and springs, must be returned to their original positions.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and securing it with mounting bolts. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new one. The procedures are separated into sections for engines with a 14-bolt housing assembly versus a 10-bolt housing assembly. Precise instructions are given for lubricating parts, inserting the seal, aligning components, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f7usuejkdkddm3
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and pressing the pulley onto the crankshaft during installation. Tightening specifications are included for attaching the pulley.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts, lifting the flywheel off, and potentially removing a ring gear. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and explains cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The steps are:
1. Use a drill bit to drill out the lock tabs of the seal.
2. Pry the seal out of the housing with a seal removal tool.
3. Inspect the seal bore and remove any debris before installing the new seal.
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, installing components like seals, spacers, washers, and plugs in reverse order of disassembly. Tools required are listed in tables. Cautions are provided about cleanliness, contamination, misassembly, and applying lubricant to parts.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f7usuejkdkddm3
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
The document provides assembly instructions for a 345C excavator final drive system. It involves assembling three carrier assemblies that contain planetary gears, installing them into a ring gear housing along with other components like bearing cones and seals. The procedure has 26 steps and requires various tools. It ensures proper bearing preload is achieved and components are cleaned, lubricated and torqued correctly during reassembly.
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f7usuejkdkddm3
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs reversing the 31 disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and securing it with mounting bolts. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new one. The procedures are separated into sections for engines with a 14-bolt housing assembly versus a 10-bolt housing assembly. Precise instructions are given for lubricating parts, inserting the seal, aligning components, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f7usuejkdkddm3
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and pressing the pulley onto the crankshaft during installation. Tightening specifications are included for attaching the pulley.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts, lifting the flywheel off, and potentially removing a ring gear. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and explains cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The steps are:
1. Use a drill bit to drill out the lock tabs of the seal.
2. Pry the seal out of the housing with a seal removal tool.
3. Inspect the seal bore and remove any debris before installing the new seal.
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, installing components like seals, spacers, washers, and plugs in reverse order of disassembly. Tools required are listed in tables. Cautions are provided about cleanliness, contamination, misassembly, and applying lubricant to parts.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f7usuejkdkddm3
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
The document provides assembly instructions for a 345C excavator final drive system. It involves assembling three carrier assemblies that contain planetary gears, installing them into a ring gear housing along with other components like bearing cones and seals. The procedure has 26 steps and requires various tools. It ensures proper bearing preload is achieved and components are cleaned, lubricated and torqued correctly during reassembly.
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f7usuejkdkddm3
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs reversing the 31 disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326D2 EXCAVATOR KGY
Configuration: 326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03124522
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded RodM12 x 1.75 by 250 mm (10 in) long 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove".
1/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
2/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00887302
6. Remove O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 3 g00887311
7. Remove O-ring seals (6) . Remove springs (7) .
3/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B) .
8. Place a shop towel over brake piston (8) . Retain brake piston (8) with Tooling (B) . Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y) . Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
4/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g00887336
9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
11. Remove plates (13) and friction discs (14) .
Illustration 8 g00887401
5/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 9 g00887405
12. Install Tooling (C) into shaft (15) . Use a prybar to remove the rotating assembly (16) from
the housing.
13. Remove Tooling (C) from shaft (15) .
Illustration 10 g00887424
14. Remove shaft (15) from rotating assembly (16) .
6/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 11 g00887426
15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15) .
Illustration 12 g00887445
16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
Illustration 13 g00887463
17. Rotate shaft (15) . Install shaft (15) into a suitable press. Install Tooling (E) . Remove
bearing race (19) from shaft (15) .
7/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 14 g00887501
18. Remove cam plate (20) from barrel assembly (21) .
Illustration 15 g00887520
19. Remove piston assemblies and retainer plate (22) from barrel assembly (21) .
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
8/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 16 g00887558
20. Remove ball (23) and springs (24) .
Illustration 17 g00887578
21. Remove bearing (25) .
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27) .
24. Remove seal (28) .
9/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g00887619
25. Remove bolts (29) and cover (30) .
Illustration 20 g00887729
26. Remove seal (31) and backup ring (32) .
Illustration 21 g00887754
27. Remove piston actuator (33) and seal (34) .
10/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 ...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 22 g00887762
28. Remove O-ring seal (35) from the housing of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 18:55:52 UTC+0800 2020
11/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 ...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326D2 EXCAVATOR KGY
Configuration: 326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03124523
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded Rod M12 x 1.75 X 250 mm (10 in) long 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G 9S-3263 Thread Lock Compound -
Note: Replace all O-ring seals and gaskets. Apply a light film of"10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause trouble later. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
1/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33) .
2/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00887729
3. Install backup ring (32) and seal (31) .
Illustration 4 g00887619
4. Install cover (30) and bolts (29) . Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
3/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 5. Apply Tooling (G) to the mating surface of seal (28) . Use Tooling (E) in order to install
seal (28) .
6. Use Tooling (F) in order to install retaining ring (27) .
Illustration 6 g00887578
7. Rotate the housing.
8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25) .
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
4/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 10. Install springs (24) into the barrel. Install ball (23) onto springs (24) .
Illustration 8 g00887520
11. Install piston assemblies and retainer plate (22) into barrel assembly (21) .
Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Install cam plate (20) onto barrel assembly (21) .
5/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15) .
Illustration 11 g00887426
14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15) .
Illustration 12 g00888710
6/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 15. Install bearing race (18) onto shaft (15) .
Note: Bearing race (18) must contact retaining ring (17) .
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15) . Install shaft (15) into rotating assembly (16) .
17. Place the pump housing into Tooling (A) .
Illustration 14 g00887401
18. Use Tooling (C) in order to install rotating assembly (16) into the housing.
7/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 15 g00887501
Illustration 16 g00887578
19. The notches in cam plate (20) must align with keys (26) . The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
20. Install plates (13) and friction discs (14) into the housing.
8/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8) .
24. Install brake piston (8) into the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level in
order to prevent damage to the O-ring seals.
9/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6) .
Illustration 21 g00887302
26. Install O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 22 g00887295
27. Install head (2) onto the body of the travel motor.
10/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 ...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1) . Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By: Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 18:56:48 UTC+0800 2020
11/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 ...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326D2 EXCAVATOR KGY
Configuration: 326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03808350
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded Rod 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/4
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g00878123
2. Install new O-ring seal (6) . Apply clean hydraulic oil on the O-ring seal.
Illustration 2 g00707267
3. Attach a suitable lifting device to travel motor (4) , as shown.
4. The weight of the travel motor is approximately 57 kg (125 lb).
Illustration 3 g00878121
2/4
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. 5. Carefully install travel motor (4) onto Tooling (A) . Slide the travel motor into the final
drive.
6. Install one of three bolts (5) that secures the travel motor to the final drive.
7. Remove Tooling (A) .
Illustration 4 g00707275
Typical example
8. Install remaining bolts (2) .
9. Connect hose assembly (3) . Connect hose assembly (1) .
10. Fill the final drive with oil.
ReferenceRefer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
ReferenceRefer to Operation and Maintenance Manual, "Final Drive Oil Level - Check" for
the correct filling procedure.
11. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
12. Obtain a hydraulic oil sample from the main S·O·S port.
ReferenceRefer to Operation and Maintenance Manual, "Sampling Interval and Location of
Sampling Valve" for the correct location.
13. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system.
ReferenceRefer to Contamination Control Guidelines, SEBF8436, "Hydraulic System
Flushing Procedure for 322C Hydraulic Excavators" for further information.
3/4
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. End By: Install the travel brake valve. Refer to Disassembly and Assembly, "Travel Brake Valve
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 18:57:43 UTC+0800 2020
4/4
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326D2 EXCAVATOR KGY
Configuration: 326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i05453056
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C
154-6184 Forcing Bolt (M 20) 2
154-6185(1)
Forcing Bolt (M 24) 2
(1)
For Use on 329 and 330 sales models
Start By:
a. Separate the track assembly.
b. Remove the travel motor.
1/3
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...