This document provides instructions for removing and installing various engine components on a Caterpillar C7 engine, including:
- Removing and installing the flywheel using lifting tools and bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer, and installing the new seal with an installer tool.
- Removing and installing the flywheel housing using lifting tools, bolts, and sealant on the mounting face.
- Removing the vibration damper and pulley by removing the drive belt and bolts, and installing them by positioning parts and tightening bolts.
Caterpillar cat 325 d excavator (prefix kdg) service repair manual (kdg00001 ...hfjsekekmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d l excavator (prefix kdg) service repair manual (kdg0000...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1) The flywheel, flywheel housing, crankshaft rear seal, crankshaft front seal, vibration damper and pulley.
2) Detailed steps are given for each procedure, including any required tools and safety precautions. Removal steps are listed first followed by installation steps.
3) Components are to be cleaned thoroughly to prevent contamination, and sealant is applied before installing the flywheel housing. Torque specifications are provided for fasteners.
Caterpillar cat 325 d l excavator (prefix kdg) service repair manual (kdg0000...hfjsekekmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d excavator (prefix kdg) service repair manual (kdg00001 ...fjsekkdmeik
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d excavator (prefix kdg) service repair manual (kdg00001 ...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d l excavator (prefix kdg) service repair manual (kdg0000...fjsekkdmeik
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1. The flywheel, flywheel housing, crankshaft rear seal, crankshaft front seal, vibration damper and pulley.
2. Detailed steps are given for each procedure, including any required tools and safety precautions. Removal steps are listed first followed by installation steps.
3. Components are to be cleaned thoroughly to prevent contamination, and sealant is applied before installing the flywheel housing. Torque specifications are provided for fasteners.
Caterpillar Cat 325D L Excavator (Prefix KDG) Service Repair Manual (KDG00001...shudun96087
This document provides instructions for removing and installing various engine components around the crankshaft of a Caterpillar C7 engine, including the flywheel, flywheel housing, crankshaft rear seal, and vibration damper/pulley. The procedures describe using various tools to remove bolts and seals, taking care to avoid contamination, and applying sealant prior to installing components. Torque specifications are provided for reinstalling bolts.
This document provides instructions for removing and installing various components of a C7 engine, including:
1. Removing the flywheel using lifting tools and bolts, and installing the flywheel using lifting tools, guide bolts, and thread lock compound.
2. Removing the crankshaft rear seal by drilling holes and using a slide hammer puller, and installing the rear seal using an installer tool.
3. Removing and installing the flywheel housing using lifting tools, bolts, and sealant.
4. Removing the vibration damper and pulley by removing bolts and a drive belt, and installing using bolts and the drive belt.
5. Removing the cranksha
Caterpillar cat 325 d excavator (prefix kdg) service repair manual (kdg00001 ...hfjsekekmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d l excavator (prefix kdg) service repair manual (kdg0000...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1) The flywheel, flywheel housing, crankshaft rear seal, crankshaft front seal, vibration damper and pulley.
2) Detailed steps are given for each procedure, including any required tools and safety precautions. Removal steps are listed first followed by installation steps.
3) Components are to be cleaned thoroughly to prevent contamination, and sealant is applied before installing the flywheel housing. Torque specifications are provided for fasteners.
Caterpillar cat 325 d l excavator (prefix kdg) service repair manual (kdg0000...hfjsekekmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d excavator (prefix kdg) service repair manual (kdg00001 ...fjsekkdmeik
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d excavator (prefix kdg) service repair manual (kdg00001 ...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d l excavator (prefix kdg) service repair manual (kdg0000...fjsekkdmeik
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1. The flywheel, flywheel housing, crankshaft rear seal, crankshaft front seal, vibration damper and pulley.
2. Detailed steps are given for each procedure, including any required tools and safety precautions. Removal steps are listed first followed by installation steps.
3. Components are to be cleaned thoroughly to prevent contamination, and sealant is applied before installing the flywheel housing. Torque specifications are provided for fasteners.
Caterpillar Cat 325D L Excavator (Prefix KDG) Service Repair Manual (KDG00001...shudun96087
This document provides instructions for removing and installing various engine components around the crankshaft of a Caterpillar C7 engine, including the flywheel, flywheel housing, crankshaft rear seal, and vibration damper/pulley. The procedures describe using various tools to remove bolts and seals, taking care to avoid contamination, and applying sealant prior to installing components. Torque specifications are provided for reinstalling bolts.
This document provides instructions for removing and installing various components of a C7 engine, including:
1. Removing the flywheel using lifting tools and bolts, and installing the flywheel using lifting tools, guide bolts, and thread lock compound.
2. Removing the crankshaft rear seal by drilling holes and using a slide hammer puller, and installing the rear seal using an installer tool.
3. Removing and installing the flywheel housing using lifting tools, bolts, and sealant.
4. Removing the vibration damper and pulley by removing bolts and a drive belt, and installing using bolts and the drive belt.
5. Removing the cranksha
Caterpillar Cat 325D L Excavator (Prefix KDG) Service Repair Manual (KDG00001...yfbr995309
This document provides instructions for removing and installing various components of a C7 engine, including:
1. Removing the flywheel using lifting tools and bolts, and installing the flywheel using lifting tools, guide bolts, and thread lock compound.
2. Removing the crankshaft rear seal by drilling holes and using a slide hammer puller, and installing the rear seal using an installer tool.
3. Removing and installing the flywheel housing using lifting tools, bolts, and sealant.
4. Removing the vibration damper and pulley by removing bolts and a drive belt, and installing using bolts and the drive belt.
5. Removing the cranksha
This document provides instructions for removing and installing components related to the crankshaft on a Caterpillar C7 engine, including:
1) Removing and installing the flywheel, which requires attaching lifting tools and removing bolts.
2) Removing and installing the crankshaft rear seal, which involves drilling holes and using a slide hammer puller.
3) Removing and installing the flywheel housing, which requires attaching lifting tools, removing bolts, and applying sealant.
4) Removing and installing the vibration damper and pulley, by removing bolts and belts.
5) Removing the crankshaft front seal, using a drill bit and slide hammer
Caterpillar Cat 325D L Excavator (Prefix KDG) Service Repair Manual (KDG00001...kesi7153062
This document provides instructions for removing and installing various engine components around the crankshaft of a Caterpillar C7 engine, including the flywheel, flywheel housing, crankshaft rear seal, and vibration damper/pulley. The procedures describe using various tools to remove bolts and seals, taking care to avoid contamination, and applying sealant prior to installing components. Torque specifications are provided for reinstalling bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar C7 engine, including:
- Removing and installing the flywheel using lifting tools and bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal with a installer tool.
- Removing and installing the flywheel housing using lifting tools and bolts, applying sealant to the mounting face.
- Removing the vibration damper and pulley by removing the drive belt and bolts, and installing them by positioning parts and tightening bolts.
Caterpillar Cat 324D and 324D L Excavator (Prefix CJX) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing various engine components on a Caterpillar 324D excavator powered by a C7 engine. The components include:
- Flywheel removal which requires attaching lifting tools and removing bolts.
- Crankshaft rear seal removal by drilling holes and using a slide hammer puller.
- Flywheel housing removal by attaching lifting tools and removing bolts fastening it to the engine block and oil pan.
- Vibration damper and pulley removal by removing the drive belt and bolts attaching the components to the crankshaft.
Caterpillar Cat 324D and 324D L Excavator (Prefix CJX) Service Repair Manual ...zan2736ban
This document provides instructions for removing and installing various engine components on a 324D excavator powered by a C7 engine, including:
- Removing and installing the flywheel using link brackets and guide bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller, and installing the new seal.
- Removing and installing the flywheel housing which requires attaching link brackets and contains fluids.
- Removing the vibration damper and pulley by removing bolts, and installing by tightening bolts to the specified torque.
- Removing the crankshaft front seal using a drill bit and slide hammer puller, and preparing for installation.
1) The documents provide instructions for removing and installing various engine components on a 324D excavator, including the flywheel, crankshaft rear seal, flywheel housing, vibration damper, and crankshaft front seal.
2) The procedures describe using various tools to remove components like the flywheel and seals, and reinstalling them in the reverse order. Precautions are given to keep parts clean and contain fluids.
3) Detailed illustrations and torque specifications are provided to correctly position and tighten components like the flywheel housing, crankshaft pulley, and seal during installation.
Caterpillar Cat 324D L Excavator (Prefix CJX) Service Repair Manual (CJX00001...f8uesjdkdmdm
1) The documents provide instructions for removing and installing various engine components on a 324D excavator, including the flywheel, crankshaft rear seal, flywheel housing, vibration damper, and crankshaft front seal.
2) The procedures describe using various tools to remove components like the flywheel and seals, and reinstalling them in the reverse order. Precautions are given to keep parts clean and contain fluids.
3) Detailed illustrations and torque specifications are provided to correctly position and tighten components like the flywheel housing, crankshaft pulley, and seal during installation.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D excavator powered by a C7 engine. The components include:
- The flywheel, which is removed using lifting brackets and guide bolts.
- The crankshaft rear seal, which is removed using a drill bit and slide hammer puller.
- The flywheel housing, which is removed after draining fluids using lifting brackets and bolts.
- The vibration damper and pulley, which are removed after loosening bolts and removing the drive belt.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process which includes draining coolant, removing the oil filter and bolts, and removing the base and cooler. The 3 step installation process describes reinstalling the gasket, base, and bolts before refilling the cooling system.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...f8sejdkdmdijd
The document provides step-by-step instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists 32 steps for disassembly, removing components like the carrier assembly, ring gear, and bearings. It then lists 13 steps for assembly, providing notes on cleanliness and replacing seals, O-rings, and other components. Tools required are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f8sejdkdmdijd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process and 4 step installation process. Separate sections also provide instructions for disassembling, assembling, removing and installing the engine oil pump.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...f8sejdkdmdijd
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f8sejdkdmdijd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific instructions for installing seals and bearings. Tools and torque specifications are provided.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual (W3K00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that involve removing components like the head, O-rings, springs, plates, and seals. The assembly section lists 28 corresponding steps to reinstall these components in reverse order, noting to clean parts thoroughly, apply lubricant, and ensure proper positioning of marked components. Special tools are listed that may be required for tasks like removing races and installing seals and rings. Proper torque values and safety precautions are also provided.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8sejdkdmdijd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing bolts to separate the final drive and travel motor assembly from the frame.
2) Attaching lifting equipment to remove the assembly and travel motor, noting orientation marks for reinstallation.
3) Reinstalling the components by reversing the removal steps and tightening bolts to specified torques.
More Related Content
Similar to Caterpillar Cat 325D L Excavator (Prefix KDG) Service Repair Manual (KDG00001 and up).pdf
Caterpillar Cat 325D L Excavator (Prefix KDG) Service Repair Manual (KDG00001...yfbr995309
This document provides instructions for removing and installing various components of a C7 engine, including:
1. Removing the flywheel using lifting tools and bolts, and installing the flywheel using lifting tools, guide bolts, and thread lock compound.
2. Removing the crankshaft rear seal by drilling holes and using a slide hammer puller, and installing the rear seal using an installer tool.
3. Removing and installing the flywheel housing using lifting tools, bolts, and sealant.
4. Removing the vibration damper and pulley by removing bolts and a drive belt, and installing using bolts and the drive belt.
5. Removing the cranksha
This document provides instructions for removing and installing components related to the crankshaft on a Caterpillar C7 engine, including:
1) Removing and installing the flywheel, which requires attaching lifting tools and removing bolts.
2) Removing and installing the crankshaft rear seal, which involves drilling holes and using a slide hammer puller.
3) Removing and installing the flywheel housing, which requires attaching lifting tools, removing bolts, and applying sealant.
4) Removing and installing the vibration damper and pulley, by removing bolts and belts.
5) Removing the crankshaft front seal, using a drill bit and slide hammer
Caterpillar Cat 325D L Excavator (Prefix KDG) Service Repair Manual (KDG00001...kesi7153062
This document provides instructions for removing and installing various engine components around the crankshaft of a Caterpillar C7 engine, including the flywheel, flywheel housing, crankshaft rear seal, and vibration damper/pulley. The procedures describe using various tools to remove bolts and seals, taking care to avoid contamination, and applying sealant prior to installing components. Torque specifications are provided for reinstalling bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar C7 engine, including:
- Removing and installing the flywheel using lifting tools and bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal with a installer tool.
- Removing and installing the flywheel housing using lifting tools and bolts, applying sealant to the mounting face.
- Removing the vibration damper and pulley by removing the drive belt and bolts, and installing them by positioning parts and tightening bolts.
Caterpillar Cat 324D and 324D L Excavator (Prefix CJX) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing various engine components on a Caterpillar 324D excavator powered by a C7 engine. The components include:
- Flywheel removal which requires attaching lifting tools and removing bolts.
- Crankshaft rear seal removal by drilling holes and using a slide hammer puller.
- Flywheel housing removal by attaching lifting tools and removing bolts fastening it to the engine block and oil pan.
- Vibration damper and pulley removal by removing the drive belt and bolts attaching the components to the crankshaft.
Caterpillar Cat 324D and 324D L Excavator (Prefix CJX) Service Repair Manual ...zan2736ban
This document provides instructions for removing and installing various engine components on a 324D excavator powered by a C7 engine, including:
- Removing and installing the flywheel using link brackets and guide bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller, and installing the new seal.
- Removing and installing the flywheel housing which requires attaching link brackets and contains fluids.
- Removing the vibration damper and pulley by removing bolts, and installing by tightening bolts to the specified torque.
- Removing the crankshaft front seal using a drill bit and slide hammer puller, and preparing for installation.
1) The documents provide instructions for removing and installing various engine components on a 324D excavator, including the flywheel, crankshaft rear seal, flywheel housing, vibration damper, and crankshaft front seal.
2) The procedures describe using various tools to remove components like the flywheel and seals, and reinstalling them in the reverse order. Precautions are given to keep parts clean and contain fluids.
3) Detailed illustrations and torque specifications are provided to correctly position and tighten components like the flywheel housing, crankshaft pulley, and seal during installation.
Caterpillar Cat 324D L Excavator (Prefix CJX) Service Repair Manual (CJX00001...f8uesjdkdmdm
1) The documents provide instructions for removing and installing various engine components on a 324D excavator, including the flywheel, crankshaft rear seal, flywheel housing, vibration damper, and crankshaft front seal.
2) The procedures describe using various tools to remove components like the flywheel and seals, and reinstalling them in the reverse order. Precautions are given to keep parts clean and contain fluids.
3) Detailed illustrations and torque specifications are provided to correctly position and tighten components like the flywheel housing, crankshaft pulley, and seal during installation.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D excavator powered by a C7 engine. The components include:
- The flywheel, which is removed using lifting brackets and guide bolts.
- The crankshaft rear seal, which is removed using a drill bit and slide hammer puller.
- The flywheel housing, which is removed after draining fluids using lifting brackets and bolts.
- The vibration damper and pulley, which are removed after loosening bolts and removing the drive belt.
Similar to Caterpillar Cat 325D L Excavator (Prefix KDG) Service Repair Manual (KDG00001 and up).pdf (9)
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process which includes draining coolant, removing the oil filter and bolts, and removing the base and cooler. The 3 step installation process describes reinstalling the gasket, base, and bolts before refilling the cooling system.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...f8sejdkdmdijd
The document provides step-by-step instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists 32 steps for disassembly, removing components like the carrier assembly, ring gear, and bearings. It then lists 13 steps for assembly, providing notes on cleanliness and replacing seals, O-rings, and other components. Tools required are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f8sejdkdmdijd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process and 4 step installation process. Separate sections also provide instructions for disassembling, assembling, removing and installing the engine oil pump.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...f8sejdkdmdijd
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f8sejdkdmdijd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific instructions for installing seals and bearings. Tools and torque specifications are provided.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual (W3K00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that involve removing components like the head, O-rings, springs, plates, and seals. The assembly section lists 28 corresponding steps to reinstall these components in reverse order, noting to clean parts thoroughly, apply lubricant, and ensure proper positioning of marked components. Special tools are listed that may be required for tasks like removing races and installing seals and rings. Proper torque values and safety precautions are also provided.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8sejdkdmdijd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing bolts to separate the final drive and travel motor assembly from the frame.
2) Attaching lifting equipment to remove the assembly and travel motor, noting orientation marks for reinstallation.
3) Reinstalling the components by reversing the removal steps and tightening bolts to specified torques.
Caterpillar Cat 336D L Excavator (Prefix JRX) Service Repair Manual (JRX00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The disassembly procedure involves 25 steps to remove components such as gears, seals, springs, and housings. The assembly procedure describes 22 steps and requires various tools to reinstall the components in reverse order. Precautions are provided for releasing spring forces and proper torque specifications.
Caterpillar Cat 336D2 L Excavator (Prefix LAM) Service Repair Manual (LAM0000...f8sejdkdmdijd
This document provides instructions for removing and installing the unit injector sleeve and unit injector hydraulic pump on a Caterpillar C9 engine. The removal process involves draining coolant, cutting threads in the unit injector sleeve using specialized tools, and pulling the sleeve out. Installation requires cleaning parts, applying seals and retaining compound, and hammering the sleeve back in. Reinstallation of the hydraulic pump involves connecting tubes and hoses, and securing it with bolts.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. It notes to mark parts locations and clean components. Reassembly follows the reverse order, noting to reinstall parts in their original locations and orientations. Proper cleaning is important to prevent contaminating the hydraulic system.
1. The document provides installation instructions for an implement pump on a D8T track-type tractor. It details 34 steps for installing various parts like valves, springs, seals and bearings into the pump housing.
2. Proper cleaning and lubrication of parts is emphasized before assembly. Tools needed are listed. Precautions are given for working with spring loaded parts to prevent injury.
3. Once assembled, the pump is attached to the tractor using bolts and hoses are connected to the manifold.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...f8sejdkdmdijd
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D2 L Excavator (Prefix LAH) Service Repair Manual (LAH0000...f8sejdkdmdijd
1) The document provides disassembly instructions for a travel motor on an excavator model 336D2 L.
2) It describes 27 steps to disassemble the various components of the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, springs and seals.
3) Precautions are provided to watch for spring forces and ensure components are marked for correct reassembly.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...f8sejdkdmdijd
The document provides instructions for disassembling and assembling a travel motor. It is a 28 step process that includes removing parts like seals, bearings, springs and installing them in reverse order. Precautions are outlined for spring loaded parts that could cause injury. Tools required are listed in tables at the beginning and end.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D EXCAVATOR KDG
Configuration: 325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301731
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
B - Guide Bolt (M12 X 1.75 by 120 mm) 1
1/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01152630
1. Attach Tooling (A) and a suitable lifting device to flywheel (2). The weight of flywheel (2)
is approximately 27 kg (60 lb).
2. Remove top bolt (1). Install Tooling (B). Remove remaining bolts (1) .
3. Remove flywheel (2) from Tooling (B).
4. Replace ring gear (3), if necessary. Use a hammer and a punch in order to remove the
flywheel ring gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 19:12:14 UTC+0800 2020
2/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D EXCAVATOR KDG
Configuration: 325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i06149434
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 1
B -
Guide Bolt
(M12 X 1.75 by 120 mm)
1
C 9S-3263 Thread Lock Compound 1
1/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g01152630
1. Raise the temperature of ring gear (3) .
Note: Do not use a torch to heat the ring gear.
2. Position ring gear (3) on flywheel (2) with the part number toward the crankshaft. Use a soft
hammer in order to seat the ring gear against the shoulder of the flywheel. Allow the ring
gear to cool.
3. Install Tooling (B) in the crankshaft.
4. Attach Tooling (A) and a suitable lifting device to flywheel (2) . The weight of flywheel (2)
is approximately 27 kg (60 lb).
5. Position flywheel (2) on Tooling (B) .
6. Apply Tooling (C) to the threads of bolts (1) .
7. Install bolts (1) . Remove Tooling (B) and install remaining bolt (1) . Tighten bolts (1) to a
torque of 120 ± 20 N·m (89 ± 15 lb ft).
8. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 19:13:10 UTC+0800 2020
2/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D EXCAVATOR KDG
Configuration: 325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02307455
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8145 Drill Bit 1
B 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Use Tooling (A) to drill three evenly spaced holes in the crankshaft rear seal.
1/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01155815
2. Use Tooling (B) to remove crankshaft rear seal (1) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 19:14:05 UTC+0800 2020
2/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D EXCAVATOR KDG
Configuration: 325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02307500
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C 1U-7598 Seal Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g01155846
1. Use Tooling (C) to install crankshaft rear seal (1) .
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 19:15:01 UTC+0800 2020
2/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D EXCAVATOR KDG
Configuration: 325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302409
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
Start By:
A. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01152919
1. Attach Tooling (A) and a suitable lifting device to flywheel housing (1). The weight of
flywheel housing (1) is approximately 25 kg (55 lb).
2. Remove bolts (2) and bolts (3) .
3. Remove bolts (4) that fasten the engine oil pan to flywheel housing (1). Remove flywheel
housing (1) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B 1U-8846 Sealant -
NOTICE
2/3
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Apply Tooling (B) to the entire mounting face of the flywheel housing prior to installation.
Illustration 2 g01152919
2. Attach Tooling (A) and a suitable lifting device to flywheel housing (1). The weight of
flywheel housing (1) is approximately 25 kg (55 lb). Position the flywheel housing on the
cylinder block. Install bolts (4) that fasten the engine oil pan to the flywheel housing.
3. Install bolts (2) and bolts (3) .
4. Check the flywheel housing runout. Refer to the Testing and Adjusting, "Flywheel Housing
- Inspect".
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 19:15:57 UTC+0800 2020
3/3
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D EXCAVATOR KDG
Configuration: 325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302464
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Illustration 1 g01152990
1. Remove drive belt (1) .
2. Remove bolts (3) and crankshaft vibration damper (2) from the crankshaft pulley.
3. Remove bolts (4) and washer (5) .
4. Remove the crankshaft pulley.
1/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Installation Procedure
Illustration 2 g01152990
1. Position the crankshaft pulley on the crankshaft. Position washer (5) and install bolts (4).
Tighten bolts (4) to a torque of 200 ± 25 N·m (148 ± 18 lb ft).
2. Install crankshaft vibration damper (2) and bolts (3) .
3. Install drive belt (1) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 19:16:53 UTC+0800 2020
2/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D EXCAVATOR KDG
Configuration: 325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02230550
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B 1U-8145 Drill Bit 1
Start By:
a. Remove the vibration damper and the pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00989224
1. Use Tooling (B) and carefully drill three evenly spaced holes in crankshaft front seal (1).
2. Use Tooling (A) to remove crankshaft front seal (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 19:17:48 UTC+0800 2020
2/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D EXCAVATOR KDG
Configuration: 325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02230558
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C 1U-7430 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g00989228
Note: The crankshaft seal is designed to be installed dry.
1. Use Tooling (C) to install crankshaft front seal (1).
End By:
a. Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration
Damper and Pulley - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 19:18:44 UTC+0800 2020
2/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D EXCAVATOR KDG
Configuration: 325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302644
Front Cover - Remove and Install
SMCS - 1166-010
Removal Procedure
Start By:
A. Remove the fan drive mounting group. Refer to Disassembly and Assembly, "Fan Drive
Mounting Group - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g01153078
1. Remove bolts (2) and bolts (3) .
2. Remove front cover (1) and the gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 2 g01153078
1. Position the gasket and front cover (1) on the engine.
2. Install bolts (2) and bolts (3) .
End By: Install the fan drive mounting group. Refer to Disassembly and Assembly, "Fan Drive
Mounting Group - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 19:19:40 UTC+0800 2020
3/3
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D EXCAVATOR KDG
Configuration: 325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302664
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
A. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
B. Remove the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit
Injector Hydraulic Pump - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g01153092
1. Support the weight of the front of the engine. Remove bolts (1) and front engine support
(2) .
Illustration 2 g01153093
2. Remove bolts (3) and bolts (5). Remove front housing (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 19:20:36 UTC+0800 2020
2/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D EXCAVATOR KDG
Configuration: 325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302689
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-9011 Component Cleaner 1
B 4C-9500 Quick Cure Primer 1
C 1U-8846 Gasket Sealant 1
1/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g01153093
1. Clean the joint face on front housing (4) with Tooling (A) .
2. Apply Tooling (B) to the joint face. Allow the primer to dry for at least three to five
minutes.
3. Apply Tooling (C) to the joint face. Spread the sealant uniformly. Front housing (4) must be
installed within ten minutes of applying the sealant.
4. Position front housing (4) on the cylinder block.
5. Install bolts (3) and bolts (5) .
Illustration 2 g01153092
6. Position front engine support (2) and install bolts (1) .
End By:
a. Install the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector
Hydraulic Pump - Install".
b. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 19:21:31 UTC+0800 2020
2/2
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D EXCAVATOR KDG
Configuration: 325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02230724
Camshaft Idler Gear - Remove and Install
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
325D & 325D L Excavators KDG00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/6/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...