This document provides instructions for removing and installing various engine components on a 324D excavator powered by a C7 engine, including:
- Removing and installing the flywheel using link brackets and guide bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller, and installing the new seal.
- Removing and installing the flywheel housing which requires attaching link brackets and contains fluids.
- Removing the vibration damper and pulley by removing bolts, and installing by tightening bolts to the specified torque.
- Removing the crankshaft front seal using a drill bit and slide hammer puller, and preparing for installation.
Caterpillar cat 324 d l excavator (prefix cjx) service repair manual (cjx0000...fjskekdmmem
The document provides instructions for removing and installing the crankshaft front seal of a C7 engine. It describes using a slide hammer puller and drill bit to remove the old seal and a front seal installer tool to press the new seal into place. The instructions should be followed after removing the vibration damper and pulley from the crankshaft. Proper cleaning and containment of fluids is emphasized.
Caterpillar cat 324 d excavator (prefix cjx) service repair manual (cjx00001 ...fjskekdmmem
The document provides instructions for removing and installing the crankshaft front seal of a C7 engine. It describes using a slide hammer puller and drill bit to remove the old seal and a front seal installer tool to press the new seal into place. The instructions should be followed after removing the vibration damper and pulley from the crankshaft. Proper cleaning and containment of fluids is emphasized.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D excavator powered by a C7 engine, including:
- Removing and installing the flywheel using various tools like link brackets and guide bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller, and installing the new seal with a seal installer.
- Removing and installing the flywheel housing using link brackets and sealant, noting precautions about containing fluids.
- Removing the vibration damper and pulley by removing bolts and installing in reverse order, tightening to specified torques.
Caterpillar Cat 324D L Excavator (Prefix CJX) Service Repair Manual (CJX00001...shudun96087
This document provides instructions for removing and installing various engine components on a Caterpillar 324D excavator powered by a C7 engine, including:
- Removing and installing the flywheel using various tools like link brackets and guide bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller, and installing the new seal with a seal installer.
- Removing and installing the flywheel housing using link brackets and sealant, noting precautions about containing fluids.
- Removing the vibration damper and pulley by removing bolts and installing in reverse order, tightening to specified torques.
Caterpillar Cat 324D L Excavator (Prefix CJX) Service Repair Manual (CJX00001...qme229722
This document provides instructions for removing and installing various components of a C7 engine, including:
- Removing the flywheel using link brackets and guide bolts.
- Installing the flywheel by heating the ring gear, applying thread lock, and torquing the bolts.
- Removing the crankshaft rear seal by drilling holes and using a slide hammer puller.
- Installing the crankshaft rear seal with a seal installer tool.
- Removing and installing the flywheel housing using link brackets and sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts, and installing by positioning parts and torquing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D excavator powered by a C7 engine, including:
- Removing and installing the flywheel using various tools.
- Removing the crankshaft rear seal by drilling holes and pulling it out.
- Installing the new crankshaft rear seal.
- Removing and installing the flywheel housing and ensuring proper runout is checked.
- Removing the vibration damper, pulley and drive belt and reinstalling them.
This document provides instructions for removing and installing various components of a C7 engine, including:
- Removing the flywheel using link brackets and guide bolts.
- Installing the flywheel by heating the ring gear, applying thread lock, and torquing the bolts.
- Removing the crankshaft rear seal by drilling holes and using a slide hammer puller.
- Installing the crankshaft rear seal with a seal installer.
- Removing and installing the flywheel housing using link brackets and sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts, and installing by positioning parts and torquing bolts.
-
Caterpillar Cat 324D L Excavator (Prefix CJX) Service Repair Manual (CJX00001...kesi7153062
This document provides instructions for removing and installing various components of a C7 engine, including:
- Removing the flywheel using link brackets and guide bolts.
- Installing the flywheel by heating the ring gear, applying thread lock, and torquing the bolts.
- Removing the crankshaft rear seal by drilling holes and using a slide hammer puller.
- Installing the crankshaft rear seal with a seal installer tool.
- Removing and installing the flywheel housing using link brackets and sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts, and installing by positioning parts and torquing bolts.
Caterpillar cat 324 d l excavator (prefix cjx) service repair manual (cjx0000...fjskekdmmem
The document provides instructions for removing and installing the crankshaft front seal of a C7 engine. It describes using a slide hammer puller and drill bit to remove the old seal and a front seal installer tool to press the new seal into place. The instructions should be followed after removing the vibration damper and pulley from the crankshaft. Proper cleaning and containment of fluids is emphasized.
Caterpillar cat 324 d excavator (prefix cjx) service repair manual (cjx00001 ...fjskekdmmem
The document provides instructions for removing and installing the crankshaft front seal of a C7 engine. It describes using a slide hammer puller and drill bit to remove the old seal and a front seal installer tool to press the new seal into place. The instructions should be followed after removing the vibration damper and pulley from the crankshaft. Proper cleaning and containment of fluids is emphasized.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D excavator powered by a C7 engine, including:
- Removing and installing the flywheel using various tools like link brackets and guide bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller, and installing the new seal with a seal installer.
- Removing and installing the flywheel housing using link brackets and sealant, noting precautions about containing fluids.
- Removing the vibration damper and pulley by removing bolts and installing in reverse order, tightening to specified torques.
Caterpillar Cat 324D L Excavator (Prefix CJX) Service Repair Manual (CJX00001...shudun96087
This document provides instructions for removing and installing various engine components on a Caterpillar 324D excavator powered by a C7 engine, including:
- Removing and installing the flywheel using various tools like link brackets and guide bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller, and installing the new seal with a seal installer.
- Removing and installing the flywheel housing using link brackets and sealant, noting precautions about containing fluids.
- Removing the vibration damper and pulley by removing bolts and installing in reverse order, tightening to specified torques.
Caterpillar Cat 324D L Excavator (Prefix CJX) Service Repair Manual (CJX00001...qme229722
This document provides instructions for removing and installing various components of a C7 engine, including:
- Removing the flywheel using link brackets and guide bolts.
- Installing the flywheel by heating the ring gear, applying thread lock, and torquing the bolts.
- Removing the crankshaft rear seal by drilling holes and using a slide hammer puller.
- Installing the crankshaft rear seal with a seal installer tool.
- Removing and installing the flywheel housing using link brackets and sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts, and installing by positioning parts and torquing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D excavator powered by a C7 engine, including:
- Removing and installing the flywheel using various tools.
- Removing the crankshaft rear seal by drilling holes and pulling it out.
- Installing the new crankshaft rear seal.
- Removing and installing the flywheel housing and ensuring proper runout is checked.
- Removing the vibration damper, pulley and drive belt and reinstalling them.
This document provides instructions for removing and installing various components of a C7 engine, including:
- Removing the flywheel using link brackets and guide bolts.
- Installing the flywheel by heating the ring gear, applying thread lock, and torquing the bolts.
- Removing the crankshaft rear seal by drilling holes and using a slide hammer puller.
- Installing the crankshaft rear seal with a seal installer.
- Removing and installing the flywheel housing using link brackets and sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts, and installing by positioning parts and torquing bolts.
-
Caterpillar Cat 324D L Excavator (Prefix CJX) Service Repair Manual (CJX00001...kesi7153062
This document provides instructions for removing and installing various components of a C7 engine, including:
- Removing the flywheel using link brackets and guide bolts.
- Installing the flywheel by heating the ring gear, applying thread lock, and torquing the bolts.
- Removing the crankshaft rear seal by drilling holes and using a slide hammer puller.
- Installing the crankshaft rear seal with a seal installer tool.
- Removing and installing the flywheel housing using link brackets and sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts, and installing by positioning parts and torquing bolts.
Caterpillar cat 325 d excavator (prefix kdg) service repair manual (kdg00001 ...hfjsekekmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d l excavator (prefix kdg) service repair manual (kdg0000...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1) The flywheel, flywheel housing, crankshaft rear seal, crankshaft front seal, vibration damper and pulley.
2) Detailed steps are given for each procedure, including any required tools and safety precautions. Removal steps are listed first followed by installation steps.
3) Components are to be cleaned thoroughly to prevent contamination, and sealant is applied before installing the flywheel housing. Torque specifications are provided for fasteners.
Caterpillar cat 325 d l excavator (prefix kdg) service repair manual (kdg0000...hfjsekekmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d excavator (prefix kdg) service repair manual (kdg00001 ...fjsekkdmeik
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d excavator (prefix kdg) service repair manual (kdg00001 ...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d l excavator (prefix kdg) service repair manual (kdg0000...fjsekkdmeik
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1. The flywheel, flywheel housing, crankshaft rear seal, crankshaft front seal, vibration damper and pulley.
2. Detailed steps are given for each procedure, including any required tools and safety precautions. Removal steps are listed first followed by installation steps.
3. Components are to be cleaned thoroughly to prevent contamination, and sealant is applied before installing the flywheel housing. Torque specifications are provided for fasteners.
Caterpillar Cat 325D and 325D L Excavator (Prefix KDG) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1) The flywheel, flywheel housing, crankshaft rear seal, and vibration damper and pulley. Tools and torque specifications are listed for each procedure.
2) Removing the crankshaft rear seal involves drilling holes in the seal and pulling it out with a slide hammer tool. Installing the new seal uses a seal installation tool.
3) Removing the flywheel housing first requires removing mounting bolts and the flywheel. Installing applies sealant and mounts the housing with bolts.
4) Instructions are provided to remove the crankshaft front
Caterpillar Cat 325D and 325D L Excavator (Prefix KDG) Service Repair Manual ...zan2736ban
This document provides instructions for removing and installing various engine components on a Caterpillar C7 engine, including:
- Removing and installing the flywheel using lifting tools and bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller, and installing the new seal with an installer tool.
- Removing and installing the flywheel housing using lifting tools, bolts, and sealant on the mounting face.
- Removing the vibration damper and pulley by removing the drive belt and bolts, and installing by positioning parts and tightening bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar C7 engine, including:
- Removing and installing the flywheel using lifting tools and bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer, and installing the new seal with an installer tool.
- Removing and installing the flywheel housing using lifting tools, bolts, and sealant on the mounting face.
- Removing the vibration damper and pulley by removing the drive belt and bolts, and installing them by positioning parts and tightening bolts.
Caterpillar Cat 325D L Excavator (Prefix KDG) Service Repair Manual (KDG00001...f8uesjdkdmdm
This document provides instructions for removing and installing various engine components on a Caterpillar C7 engine, including:
- Removing and installing the flywheel using lifting tools and bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller, and installing the new seal with an installer tool.
- Removing and installing the flywheel housing using lifting tools, bolts, and sealant on the mounting face.
- Removing the vibration damper and pulley by removing the drive belt and bolts, and installing by positioning parts and tightening bolts.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in the reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...zan2736ban
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix L5X) Service Repair Manual Instant D...zan2736ban
This document provides instructions for removing and installing the rear gear group and flywheel on a 336D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and seals. Installation involves cleaning parts and using tools to carefully lower bearings and gears into place while matching specific dimensions, then reinstalling covers, seals, and bolts. Precautions are given to keep parts clean and properly position oil passages.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids, releasing pressure from the hydraulic system, and preventing contamination.
Caterpillar Cat 336D L Excavator (Prefix JRX) Service Repair Manual Instant D...zan2736ban
1) The document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit.
2) The disassembly procedure involves using various tools to remove 25 components of the final drive including gears, seals, plates, and housings.
3) The assembly procedure is the reverse of disassembly and provides instructions for installing the components using loctite and torquing bolts to the specified values.
Caterpillar Cat 336D L Excavator (Prefix JBF) Service Repair Manual Instant D...zan2736ban
This document provides instructions for installing a unit injector sleeve on a Caterpillar C9 engine. It outlines the required tools and gives step-by-step details for cleaning the sleeve and cylinder head bore, lubricating seals, applying retaining compound to the sleeve, and installing the sleeve using a hammer and installer tool. Proper installation is important to prevent leaks that could cause low pressure or oil consumption issues.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...zan2736ban
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...zan2736ban
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix DTS) Service Repair Manual Instant D...zan2736ban
This document provides instructions for disassembling and assembling the piston pump of a 336D L excavator. The disassembly procedure involves removing 30 individual parts from the pump housing in a specific order. The assembly procedure describes installing the parts in the reverse order and notes that some components require special tools or heating/cooling to install properly. Precautions are provided to prevent injury from parts under spring tension.
Caterpillar Cat 336D and 336D L Excavator (Prefix MPL) Service Repair Manual ...zan2736ban
1. The document provides step-by-step instructions for disassembling and assembling the piston pump of a 336D excavator.
2. Disassembly involves removing over 30 individual parts in a specific order, including housings, seals, springs, pistons, and bearings.
3. Assembly requires carefully installing the parts in reverse order and adjusting shims and bearings to ensure proper clearance and operation.
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...zan2736ban
1. The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. Removal and installation procedures are outlined in steps with accompanying illustrations. Cleanliness is emphasized and inspecting parts for wear or damage before reassembly.
3. Tools required are listed for some procedures. Proper lifting of heavy components like the hydraulic oil cooler is advised to prevent injury.
Caterpillar Cat 336D and 336D L Excavator (Prefix JBT) Service Repair Manual ...zan2736ban
The document provides instructions for servicing the piston pump (hydraulic fan) on a 336D excavator. It describes how to install the piston pump, connecting hoses and harness. It then details how to disassemble, remove and assemble the piston motor (hydraulic fan), including removing springs and pins, and replacing seals and bearings. Personal protective equipment is recommended when working with spring loaded parts.
More Related Content
Similar to Caterpillar Cat 324D and 324D L Excavator (Prefix CJX) Service Repair Manual Instant Download.pdf
Caterpillar cat 325 d excavator (prefix kdg) service repair manual (kdg00001 ...hfjsekekmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d l excavator (prefix kdg) service repair manual (kdg0000...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1) The flywheel, flywheel housing, crankshaft rear seal, crankshaft front seal, vibration damper and pulley.
2) Detailed steps are given for each procedure, including any required tools and safety precautions. Removal steps are listed first followed by installation steps.
3) Components are to be cleaned thoroughly to prevent contamination, and sealant is applied before installing the flywheel housing. Torque specifications are provided for fasteners.
Caterpillar cat 325 d l excavator (prefix kdg) service repair manual (kdg0000...hfjsekekmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d excavator (prefix kdg) service repair manual (kdg00001 ...fjsekkdmeik
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d excavator (prefix kdg) service repair manual (kdg00001 ...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
- Removing and installing the flywheel using lifting tools and guide bolts.
- Removing the crankshaft rear seal by drilling holes and pulling it out, and installing the new seal.
- Removing the flywheel housing by lifting it off with bolts and installing it with sealant on the mounting face.
- Removing the vibration damper and pulley by removing bolts and belts, and installing them by positioning and tightening bolts.
Caterpillar cat 325 d l excavator (prefix kdg) service repair manual (kdg0000...fjsekkdmeik
This document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1. The flywheel, flywheel housing, crankshaft rear seal, crankshaft front seal, vibration damper and pulley.
2. Detailed steps are given for each procedure, including any required tools and safety precautions. Removal steps are listed first followed by installation steps.
3. Components are to be cleaned thoroughly to prevent contamination, and sealant is applied before installing the flywheel housing. Torque specifications are provided for fasteners.
Caterpillar Cat 325D and 325D L Excavator (Prefix KDG) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1) The flywheel, flywheel housing, crankshaft rear seal, and vibration damper and pulley. Tools and torque specifications are listed for each procedure.
2) Removing the crankshaft rear seal involves drilling holes in the seal and pulling it out with a slide hammer tool. Installing the new seal uses a seal installation tool.
3) Removing the flywheel housing first requires removing mounting bolts and the flywheel. Installing applies sealant and mounts the housing with bolts.
4) Instructions are provided to remove the crankshaft front
Caterpillar Cat 325D and 325D L Excavator (Prefix KDG) Service Repair Manual ...zan2736ban
This document provides instructions for removing and installing various engine components on a Caterpillar C7 engine, including:
- Removing and installing the flywheel using lifting tools and bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller, and installing the new seal with an installer tool.
- Removing and installing the flywheel housing using lifting tools, bolts, and sealant on the mounting face.
- Removing the vibration damper and pulley by removing the drive belt and bolts, and installing by positioning parts and tightening bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar C7 engine, including:
- Removing and installing the flywheel using lifting tools and bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer, and installing the new seal with an installer tool.
- Removing and installing the flywheel housing using lifting tools, bolts, and sealant on the mounting face.
- Removing the vibration damper and pulley by removing the drive belt and bolts, and installing them by positioning parts and tightening bolts.
Caterpillar Cat 325D L Excavator (Prefix KDG) Service Repair Manual (KDG00001...f8uesjdkdmdm
This document provides instructions for removing and installing various engine components on a Caterpillar C7 engine, including:
- Removing and installing the flywheel using lifting tools and bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller, and installing the new seal with an installer tool.
- Removing and installing the flywheel housing using lifting tools, bolts, and sealant on the mounting face.
- Removing the vibration damper and pulley by removing the drive belt and bolts, and installing by positioning parts and tightening bolts.
Similar to Caterpillar Cat 324D and 324D L Excavator (Prefix CJX) Service Repair Manual Instant Download.pdf (10)
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in the reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...zan2736ban
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix L5X) Service Repair Manual Instant D...zan2736ban
This document provides instructions for removing and installing the rear gear group and flywheel on a 336D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and seals. Installation involves cleaning parts and using tools to carefully lower bearings and gears into place while matching specific dimensions, then reinstalling covers, seals, and bolts. Precautions are given to keep parts clean and properly position oil passages.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids, releasing pressure from the hydraulic system, and preventing contamination.
Caterpillar Cat 336D L Excavator (Prefix JRX) Service Repair Manual Instant D...zan2736ban
1) The document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit.
2) The disassembly procedure involves using various tools to remove 25 components of the final drive including gears, seals, plates, and housings.
3) The assembly procedure is the reverse of disassembly and provides instructions for installing the components using loctite and torquing bolts to the specified values.
Caterpillar Cat 336D L Excavator (Prefix JBF) Service Repair Manual Instant D...zan2736ban
This document provides instructions for installing a unit injector sleeve on a Caterpillar C9 engine. It outlines the required tools and gives step-by-step details for cleaning the sleeve and cylinder head bore, lubricating seals, applying retaining compound to the sleeve, and installing the sleeve using a hammer and installer tool. Proper installation is important to prevent leaks that could cause low pressure or oil consumption issues.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...zan2736ban
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...zan2736ban
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix DTS) Service Repair Manual Instant D...zan2736ban
This document provides instructions for disassembling and assembling the piston pump of a 336D L excavator. The disassembly procedure involves removing 30 individual parts from the pump housing in a specific order. The assembly procedure describes installing the parts in the reverse order and notes that some components require special tools or heating/cooling to install properly. Precautions are provided to prevent injury from parts under spring tension.
Caterpillar Cat 336D and 336D L Excavator (Prefix MPL) Service Repair Manual ...zan2736ban
1. The document provides step-by-step instructions for disassembling and assembling the piston pump of a 336D excavator.
2. Disassembly involves removing over 30 individual parts in a specific order, including housings, seals, springs, pistons, and bearings.
3. Assembly requires carefully installing the parts in reverse order and adjusting shims and bearings to ensure proper clearance and operation.
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...zan2736ban
1. The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. Removal and installation procedures are outlined in steps with accompanying illustrations. Cleanliness is emphasized and inspecting parts for wear or damage before reassembly.
3. Tools required are listed for some procedures. Proper lifting of heavy components like the hydraulic oil cooler is advised to prevent injury.
Caterpillar Cat 336D and 336D L Excavator (Prefix JBT) Service Repair Manual ...zan2736ban
The document provides instructions for servicing the piston pump (hydraulic fan) on a 336D excavator. It describes how to install the piston pump, connecting hoses and harness. It then details how to disassemble, remove and assemble the piston motor (hydraulic fan), including removing springs and pins, and replacing seals and bearings. Personal protective equipment is recommended when working with spring loaded parts.
Caterpillar Cat 330F, 330F L and 330F LN Excavator (Prefix WBA) Service Repai...zan2736ban
The document provides instructions for disassembling a Caterpillar 330F L excavator travel motor. It lists 28 steps to completely disassemble the travel motor, including removing components like the head, springs, pistons, bearings, and housing. Various tools are required, including bolts, nuts, retaining rings, presses, and pullers to separate the individual parts in a specific sequence. Safety precautions are provided throughout to properly release pressures and contain fluids.
Caterpillar Cat 330F, 330F L and 330F LN Excavator (Prefix JHF) Service Repai...zan2736ban
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, and using shims to set the proper bearing preload when reassembling components. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar Cat 330F and 330F L Excavator (Prefix LCG) Service Repair Manual ...zan2736ban
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. It involves 37 steps to disassemble the final drive which includes removing gears, shafts, carriers, and housing components. The assembly process involves 33 steps including pressing in new bearings, installing seals, adjusting the bearing preload using shims, and reattaching the sprocket housing. Tools such as retaining ring pliers, eyebolts and a transmission repair stand are required. Precise measurements are taken to determine the correct shim thickness for proper bearing preload.
Caterpillar Cat 330F and 330F L Excavator (Prefix HCK) Service Repair Manual ...zan2736ban
The document provides instructions for disassembling a travel motor. It describes 28 steps to remove parts like the head, brake piston, rotating assembly, bearings, seals, and more. Various tools are required including bolts, nuts, retaining ring pliers, bearing pullers, and more. Safety notices are included to warn of potential spring forces or fluid hazards during disassembly.
Caterpillar Cat 330F and 330F L Excavator (Prefix GHT) Service Repair Manual ...zan2736ban
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and containing fluids during disassembly.
Caterpillar Cat 330D2 L Excavator (Prefix ZBF) Service Repair Manual Instant ...zan2736ban
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly, including gears, shafts, seals, and housings. The assembly section outlines 37 steps to reinstall these parts in reverse order, noting that cleanliness is important, old seals should be replaced, and parts should be lubricated before assembly. Precise measurements and shimming are required to set proper bearing preload when reinstalling the main housing.
Caterpillar Cat 330D2 L Excavator (Prefix SZK) Service Repair Manual Instant ...zan2736ban
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly, including gears, shafts, seals, and housings. The assembly process similarly provides step-by-step instructions for installing the parts back onto the final drive, noting the importance of cleanliness and applying lubricants between parts. Proper bearing preload is achieved through measuring clearance and installing shims as needed.
Caterpillar Cat 330D2 L Excavator (Prefix PTE) Service Repair Manual Instant ...zan2736ban
This document provides instructions for removing and installing a turbocharger for top mounted engines. The removal process involves disconnecting hoses and tubes, removing bolts and nuts, and taking off the turbocharger assembly. For installation, components are cleaned and inspected, gaskets and seals are installed, bolts are tightened in a specified order and torque, and hoses/tubes are reconnected. Tools, safety notices, and illustrations are included to aid the process.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D EXCAVATOR CJX
Configuration: 324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301731
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
B - Guide Bolt (M12 X 1.75 by 120 mm) 1
1/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01152630
1. Attach Tooling (A) and a suitable lifting device to flywheel (2). The weight of flywheel (2)
is approximately 27 kg (60 lb).
2. Remove top bolt (1). Install Tooling (B). Remove remaining bolts (1) .
3. Remove flywheel (2) from Tooling (B).
4. Replace ring gear (3), if necessary. Use a hammer and a punch in order to remove the
flywheel ring gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:30:31 UTC+0800 2020
2/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D EXCAVATOR CJX
Configuration: 324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i06149434
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 1
B -
Guide Bolt
(M12 X 1.75 by 120 mm)
1
C 9S-3263 Thread Lock Compound 1
1/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g01152630
1. Raise the temperature of ring gear (3) .
Note: Do not use a torch to heat the ring gear.
2. Position ring gear (3) on flywheel (2) with the part number toward the crankshaft. Use a soft
hammer in order to seat the ring gear against the shoulder of the flywheel. Allow the ring
gear to cool.
3. Install Tooling (B) in the crankshaft.
4. Attach Tooling (A) and a suitable lifting device to flywheel (2) . The weight of flywheel (2)
is approximately 27 kg (60 lb).
5. Position flywheel (2) on Tooling (B) .
6. Apply Tooling (C) to the threads of bolts (1) .
7. Install bolts (1) . Remove Tooling (B) and install remaining bolt (1) . Tighten bolts (1) to a
torque of 120 ± 20 N·m (89 ± 15 lb ft).
8. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:31:30 UTC+0800 2020
2/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D EXCAVATOR CJX
Configuration: 324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02307455
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8145 Drill Bit 1
B 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Use Tooling (A) to drill three evenly spaced holes in the crankshaft rear seal.
1/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01155815
2. Use Tooling (B) to remove crankshaft rear seal (1) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:32:29 UTC+0800 2020
2/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D EXCAVATOR CJX
Configuration: 324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02307500
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C 1U-7598 Seal Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g01155846
1. Use Tooling (C) to install crankshaft rear seal (1) .
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:33:29 UTC+0800 2020
2/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D EXCAVATOR CJX
Configuration: 324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302409
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
Start By:
A. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01152919
1. Attach Tooling (A) and a suitable lifting device to flywheel housing (1). The weight of
flywheel housing (1) is approximately 25 kg (55 lb).
2. Remove bolts (2) and bolts (3) .
3. Remove bolts (4) that fasten the engine oil pan to flywheel housing (1). Remove flywheel
housing (1) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B 1U-8846 Sealant -
NOTICE
2/3
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Apply Tooling (B) to the entire mounting face of the flywheel housing prior to installation.
Illustration 2 g01152919
2. Attach Tooling (A) and a suitable lifting device to flywheel housing (1). The weight of
flywheel housing (1) is approximately 25 kg (55 lb). Position the flywheel housing on the
cylinder block. Install bolts (4) that fasten the engine oil pan to the flywheel housing.
3. Install bolts (2) and bolts (3) .
4. Check the flywheel housing runout. Refer to the Testing and Adjusting, "Flywheel Housing
- Inspect".
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:34:28 UTC+0800 2020
3/3
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D EXCAVATOR CJX
Configuration: 324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302464
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Illustration 1 g01152990
1. Remove drive belt (1) .
2. Remove bolts (3) and crankshaft vibration damper (2) from the crankshaft pulley.
3. Remove bolts (4) and washer (5) .
4. Remove the crankshaft pulley.
1/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Installation Procedure
Illustration 2 g01152990
1. Position the crankshaft pulley on the crankshaft. Position washer (5) and install bolts (4).
Tighten bolts (4) to a torque of 200 ± 25 N·m (148 ± 18 lb ft).
2. Install crankshaft vibration damper (2) and bolts (3) .
3. Install drive belt (1) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:35:27 UTC+0800 2020
2/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D EXCAVATOR CJX
Configuration: 324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02230550
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B 1U-8145 Drill Bit 1
Start By:
a. Remove the vibration damper and the pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00989224
1. Use Tooling (B) and carefully drill three evenly spaced holes in crankshaft front seal (1).
2. Use Tooling (A) to remove crankshaft front seal (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:36:27 UTC+0800 2020
2/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D EXCAVATOR CJX
Configuration: 324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02230558
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C 1U-7430 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g00989228
Note: The crankshaft seal is designed to be installed dry.
1. Use Tooling (C) to install crankshaft front seal (1).
End By:
a. Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration
Damper and Pulley - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:37:26 UTC+0800 2020
2/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D EXCAVATOR CJX
Configuration: 324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302644
Front Cover - Remove and Install
SMCS - 1166-010
Removal Procedure
Start By:
A. Remove the fan drive mounting group. Refer to Disassembly and Assembly, "Fan Drive
Mounting Group - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g01153078
1. Remove bolts (2) and bolts (3) .
2. Remove front cover (1) and the gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 2 g01153078
1. Position the gasket and front cover (1) on the engine.
2. Install bolts (2) and bolts (3) .
End By: Install the fan drive mounting group. Refer to Disassembly and Assembly, "Fan Drive
Mounting Group - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:38:25 UTC+0800 2020
3/3
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D EXCAVATOR CJX
Configuration: 324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302664
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
A. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
B. Remove the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit
Injector Hydraulic Pump - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g01153092
1. Support the weight of the front of the engine. Remove bolts (1) and front engine support
(2) .
Illustration 2 g01153093
2. Remove bolts (3) and bolts (5). Remove front housing (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:39:24 UTC+0800 2020
2/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D EXCAVATOR CJX
Configuration: 324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302689
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-9011 Component Cleaner 1
B 4C-9500 Quick Cure Primer 1
C 1U-8846 Gasket Sealant 1
1/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g01153093
1. Clean the joint face on front housing (4) with Tooling (A) .
2. Apply Tooling (B) to the joint face. Allow the primer to dry for at least three to five
minutes.
3. Apply Tooling (C) to the joint face. Spread the sealant uniformly. Front housing (4) must be
installed within ten minutes of applying the sealant.
4. Position front housing (4) on the cylinder block.
5. Install bolts (3) and bolts (5) .
Illustration 2 g01153092
6. Position front engine support (2) and install bolts (1) .
End By:
a. Install the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector
Hydraulic Pump - Install".
b. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:40:24 UTC+0800 2020
2/2
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D EXCAVATOR CJX
Configuration: 324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02230724
Camshaft Idler Gear - Remove and Install
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...