The document provides instructions for disassembling a final drive assembly. Key steps include:
1. Marking the final drive assembly and securing it to a repair stand.
2. Removing the cover and internal gears and shafts.
3. Disassembling the carrier assemblies by pressing out shafts and removing thrust washers and bearings.
Caterpillar cat 325 d l excavator (prefix azp) service repair manual (azp0000...hfjsekekmmd
The document provides instructions for disassembling a service repair manual for excavator models 325D and 325D L. It lists required tools and a 33-step procedure that includes removing components like the final drive, cover, gears, seals, and housing pieces. Cleanliness is important during disassembly. Parts must be reinstalled in their original locations and lifting is required as component weights range from 30 to 688 pounds.
Caterpillar cat 325 d l excavator (prefix azp) service repair manual (azp0000...fjsekdmmeed
The document provides disassembly instructions for a final drive in 3 steps:
1. Remove the final drive from the machine and disassemble the cover assembly.
2. Disassemble the carrier assembly by removing gears, shafts, washers and bearings.
3. Separate the main housing from the motor housing and remove remaining components.
Cleanliness is important and tools are required to lift and separate heavy parts.
Caterpillar cat 325 d excavator (prefix azp) service repair manual (azp00001 ...fjskeazqkkdmme
The document provides instructions for disassembling a service repair manual for excavator models 325D and 325D L. It lists required tools and a 33-step procedure involving removing components like the final drive, cover, gears, seals, and housing pieces. Cleanliness is important during disassembly to prevent dirt entry. Weights of removed parts are provided, ranging from 14 to 312 kg.
Caterpillar Cat 325D and 325D L Excavator (Prefix DBH) Service Repair Manual ...zan2736ban
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing in over 30 numbered steps. Precautions are given to mark parts locations and support heavy components during removal. Required tools include lifting devices, brackets, and pullers to separate pieces.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...f8uesjdkdmdm
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...jdkskmmdmd1
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
Caterpillar Cat 325D and 325D L Excavator (Prefix DBH) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...ufs89eodkdmdm
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing using specialized tools over 30 detailed steps. Cleanliness is emphasized throughout to prevent dirt contamination during reassembly.
Caterpillar cat 325 d l excavator (prefix azp) service repair manual (azp0000...hfjsekekmmd
The document provides instructions for disassembling a service repair manual for excavator models 325D and 325D L. It lists required tools and a 33-step procedure that includes removing components like the final drive, cover, gears, seals, and housing pieces. Cleanliness is important during disassembly. Parts must be reinstalled in their original locations and lifting is required as component weights range from 30 to 688 pounds.
Caterpillar cat 325 d l excavator (prefix azp) service repair manual (azp0000...fjsekdmmeed
The document provides disassembly instructions for a final drive in 3 steps:
1. Remove the final drive from the machine and disassemble the cover assembly.
2. Disassemble the carrier assembly by removing gears, shafts, washers and bearings.
3. Separate the main housing from the motor housing and remove remaining components.
Cleanliness is important and tools are required to lift and separate heavy parts.
Caterpillar cat 325 d excavator (prefix azp) service repair manual (azp00001 ...fjskeazqkkdmme
The document provides instructions for disassembling a service repair manual for excavator models 325D and 325D L. It lists required tools and a 33-step procedure involving removing components like the final drive, cover, gears, seals, and housing pieces. Cleanliness is important during disassembly to prevent dirt entry. Weights of removed parts are provided, ranging from 14 to 312 kg.
Caterpillar Cat 325D and 325D L Excavator (Prefix DBH) Service Repair Manual ...zan2736ban
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing in over 30 numbered steps. Precautions are given to mark parts locations and support heavy components during removal. Required tools include lifting devices, brackets, and pullers to separate pieces.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...f8uesjdkdmdm
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...jdkskmmdmd1
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
Caterpillar Cat 325D and 325D L Excavator (Prefix DBH) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...ufs89eodkdmdm
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing using specialized tools over 30 detailed steps. Cleanliness is emphasized throughout to prevent dirt contamination during reassembly.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...f7usuejkdkddm3
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...pwg56547003
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
Caterpillar Cat 325D and 325D L Excavator (Prefix DBH) Service Repair Manual ...fujkskemdmdm4r
The document provides step-by-step instructions for disassembling the final drive of an excavator. It lists 33 steps including removing bolts, washers, gears, and other components using various tools. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be marked for proper reinstallation. Weights of removed parts are provided ranging from approximately 30 to 312 kg.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...f8sejdkdmdijd
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing in over 30 numbered steps. Precautions are given to mark parts locations and handle heavy components with lifting devices.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing using specialized tools over 30 detailed steps. Cleanliness is emphasized throughout to prevent dirt contamination during reassembly.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing using specialized tools over 30 detailed steps. Cleanliness is emphasized throughout to prevent dirt contamination during reassembly.
Caterpillar Cat 325D and 325D L Excavator (Prefix DBH) Service Repair Manual ...fijsekkdmdm2w
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing in over 30 numbered steps. Precautions are given to mark parts locations and handle heavy components with lifting devices.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing in over 30 numbered steps, with illustrations provided. Proper tools and safety precautions are noted throughout the detailed disassembly process.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process which includes draining coolant, removing the oil filter and bolts, and removing the base and cooler. The 3 step installation process describes reinstalling the gasket, base, and bolts before refilling the cooling system.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...f8sejdkdmdijd
The document provides step-by-step instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists 32 steps for disassembly, removing components like the carrier assembly, ring gear, and bearings. It then lists 13 steps for assembly, providing notes on cleanliness and replacing seals, O-rings, and other components. Tools required are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f8sejdkdmdijd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process and 4 step installation process. Separate sections also provide instructions for disassembling, assembling, removing and installing the engine oil pump.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...f8sejdkdmdijd
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f8sejdkdmdijd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific instructions for installing seals and bearings. Tools and torque specifications are provided.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
More Related Content
Similar to Caterpillar Cat 325D L Excavator (Prefix AZP) Service Repair Manual (AZP00001 and up).pdf
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...f7usuejkdkddm3
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...pwg56547003
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
Caterpillar Cat 325D and 325D L Excavator (Prefix DBH) Service Repair Manual ...fujkskemdmdm4r
The document provides step-by-step instructions for disassembling the final drive of an excavator. It lists 33 steps including removing bolts, washers, gears, and other components using various tools. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be marked for proper reinstallation. Weights of removed parts are provided ranging from approximately 30 to 312 kg.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...f8sejdkdmdijd
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing in over 30 numbered steps. Precautions are given to mark parts locations and handle heavy components with lifting devices.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing using specialized tools over 30 detailed steps. Cleanliness is emphasized throughout to prevent dirt contamination during reassembly.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing using specialized tools over 30 detailed steps. Cleanliness is emphasized throughout to prevent dirt contamination during reassembly.
Caterpillar Cat 325D and 325D L Excavator (Prefix DBH) Service Repair Manual ...fijsekkdmdm2w
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing in over 30 numbered steps. Precautions are given to mark parts locations and handle heavy components with lifting devices.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing in over 30 numbered steps, with illustrations provided. Proper tools and safety precautions are noted throughout the detailed disassembly process.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
Similar to Caterpillar Cat 325D L Excavator (Prefix AZP) Service Repair Manual (AZP00001 and up).pdf (12)
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process which includes draining coolant, removing the oil filter and bolts, and removing the base and cooler. The 3 step installation process describes reinstalling the gasket, base, and bolts before refilling the cooling system.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...f8sejdkdmdijd
The document provides step-by-step instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists 32 steps for disassembly, removing components like the carrier assembly, ring gear, and bearings. It then lists 13 steps for assembly, providing notes on cleanliness and replacing seals, O-rings, and other components. Tools required are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f8sejdkdmdijd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process and 4 step installation process. Separate sections also provide instructions for disassembling, assembling, removing and installing the engine oil pump.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...f8sejdkdmdijd
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f8sejdkdmdijd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific instructions for installing seals and bearings. Tools and torque specifications are provided.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual (W3K00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that involve removing components like the head, O-rings, springs, plates, and seals. The assembly section lists 28 corresponding steps to reinstall these components in reverse order, noting to clean parts thoroughly, apply lubricant, and ensure proper positioning of marked components. Special tools are listed that may be required for tasks like removing races and installing seals and rings. Proper torque values and safety precautions are also provided.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8sejdkdmdijd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing bolts to separate the final drive and travel motor assembly from the frame.
2) Attaching lifting equipment to remove the assembly and travel motor, noting orientation marks for reinstallation.
3) Reinstalling the components by reversing the removal steps and tightening bolts to specified torques.
Caterpillar Cat 336D L Excavator (Prefix JRX) Service Repair Manual (JRX00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The disassembly procedure involves 25 steps to remove components such as gears, seals, springs, and housings. The assembly procedure describes 22 steps and requires various tools to reinstall the components in reverse order. Precautions are provided for releasing spring forces and proper torque specifications.
Caterpillar Cat 336D2 L Excavator (Prefix LAM) Service Repair Manual (LAM0000...f8sejdkdmdijd
This document provides instructions for removing and installing the unit injector sleeve and unit injector hydraulic pump on a Caterpillar C9 engine. The removal process involves draining coolant, cutting threads in the unit injector sleeve using specialized tools, and pulling the sleeve out. Installation requires cleaning parts, applying seals and retaining compound, and hammering the sleeve back in. Reinstallation of the hydraulic pump involves connecting tubes and hoses, and securing it with bolts.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. It notes to mark parts locations and clean components. Reassembly follows the reverse order, noting to reinstall parts in their original locations and orientations. Proper cleaning is important to prevent contaminating the hydraulic system.
1. The document provides installation instructions for an implement pump on a D8T track-type tractor. It details 34 steps for installing various parts like valves, springs, seals and bearings into the pump housing.
2. Proper cleaning and lubrication of parts is emphasized before assembly. Tools needed are listed. Precautions are given for working with spring loaded parts to prevent injury.
3. Once assembled, the pump is attached to the tractor using bolts and hoses are connected to the manifold.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...f8sejdkdmdijd
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D2 L Excavator (Prefix LAH) Service Repair Manual (LAH0000...f8sejdkdmdijd
1) The document provides disassembly instructions for a travel motor on an excavator model 336D2 L.
2) It describes 27 steps to disassemble the various components of the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, springs and seals.
3) Precautions are provided to watch for spring forces and ensure components are marked for correct reassembly.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...f8sejdkdmdijd
The document provides instructions for disassembling and assembling a travel motor. It is a 28 step process that includes removing parts like seals, bearings, springs and installing them in reverse order. Precautions are outlined for spring loaded parts that could cause injury. Tools required are listed in tables at the beginning and end.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 154-6181 Forcing Screw 1
D 138-7574 Link Bracket 2
E
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F 1U-8846 Gasket Sealant 1
Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3/12
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
Illustration 3 g00708091
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
4/12
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00708235
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
Illustration 5 g00708092
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
Illustration 6 g01304883
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
5/12
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g00708144
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
Illustration 8 g00708218
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
6/12
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g00708162
13. Remove sun gear (14) from carrier assembly (15).
Illustration 10 g00708325
14. Remove spacer (16).
Illustration 11 g00708184
Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
7/12
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 12 g00708360
16. Use a screwdriver or a chisel in order to separate the two ring gears (17).
Note: The two ring gears are held together with Tooling (F). It may be necessary to heat the
ring gears in order to soften the sealant. Do not heat over 135 °C (275 °F) for more than
thirty minutes.
Illustration 13 g00708172
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
Illustration 14 g00708175
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
8/12
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g00708370
Illustration 16 g00708220
b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
9/12
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g00708186
22. Remove O-ring seal (24) from main housing (18).
Illustration 18 g00708187
23. Remove bolts (25) from gear (26).
Illustration 19 g00708202
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from the main housing (18) once gear (26) is
removed. Make sure that the motor housing is supported.
10/12
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engin...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g00708211
25. Remove shims (27) from the main housing.
Illustration 21 g00708212
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from the motor housing (28). The combined weight of main housing (18) and the
final drive sprocket is approximately 82 kg (180 lb).
Illustration 22 g00708214
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
11/12
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engin...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g00708215
Illustration 24 g00708216
30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 22 11:49:59 UTC+0800 2020
12/12
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engin...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D L EXCAVATOR AZP
Configuration: 325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8646-22 Publication Date -01/02/2015 Date Updated -12/09/2018
i02783051
Final Drive - Disassemble
SMCS - 4050-015
S/N - A3R1-1021
S/N - AZP1-UP
S/N - DBH1-UP
S/N - EJC1-643
S/N - GBR1-UP
S/N - GPB1-801
S/N - JJG1-813
S/N - KBE1-UP
S/N - LAB1-415
S/N - LAL1-250
S/N - MCL1-201
S/N - NAC1-250
S/N - PAL1-UP
S/N - PKE1-814
S/N - SCR1-774
S/N - SYM1-617
1/13
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. S/N - T2D1-322
S/N - T2S1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 194-3878 Spanner Socket 1
E 138-7574 Link Bracket 2
F
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
G
1U-7600 Slide Hammer Puller Gp 1
8T-0266 Bolt 1
Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
Note: Some of the images that are in this procedure do not show the sprocket assembly that
is attached to the final drive housing. If necessary, the weights that are given include the
weight of the sprocket assembly.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
2/13
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The weight of the final drive assembly is
approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. Remove the cover. The weight of the cover is approximately 32 kg
(70 lb).
Illustration 3 g00879362
3/13
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 5. Remove bolts (3). Remove gear (5). Check plate (6). Replace plate (6) if wear is shown.
Remove plugs (4) from cover (2).
Illustration 4 g00879365
6. Remove O-ring seal (7) from plugs (4).
Illustration 5 g00780428
7. Remove gear (8). Remove spacer (9).
Illustration 6 g00780432
4/13
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 8. Remove retaining ring (10) with Tooling (C). Remove washer (11). Remove gear (12).
Remove bearing assembly (13). Remove second washer (11).
9. Repeat Step 8 for the remaining two gear assemblies.
Illustration 7 g00781401
10. Remove retaining ring (14).
Illustration 8 g00781407
11. Remove carrier assembly (15).
5/13
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 9 g01389593
12. Use a suitable press in order to remove the shafts from carrier assembly (15).
Illustration 10 g00781412
13. Remove gear (16). Remove spacer (17).
Illustration 11 g00781466
6/13
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 14. Remove retaining ring (18).
15. Remove carrier assembly (19).
Illustration 12 g00879368
16. Disassemble carrier assembly (19), as follows.
a. Drive spring pin (20) into planetary shaft (21) with a hammer and a punch.
Illustration 13 g00781476
b. Remove planetary shaft (21).
c. Remove spring pin (20) from planetary shaft (21) with a hammer and a punch.
7/13
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 14 g00781516
d. Remove thrust washers (22) and planetary gear (24) from the carrier assembly.
e. Remove bearing (23) from planetary gear (24).
17. Repeat Steps 16.a through 16.e for the other two planetary.
Illustration 15 g00781529
18. Remove gear (25). Remove spacer (26).
Illustration 16 g00781559
19. Remove carrier assembly (27).
20. Use two people to remove carrier assembly (27). The weight of the carrier assembly is
approximately 38 kg (85 lb).
21. Disassemble carrier assembly (27), as follows.
8/13
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 17 g00781719
a. Drive spring pin (29) into planetary shaft (28) with a hammer and a punch.
Illustration 18 g00781601
b. Remove planetary shaft (28).
c. Remove spring pin (29) from planetary shaft (28) with a hammer and a punch.
Illustration 19 g00781607
d. Remove thrust washers (30) and planetary gear (32) from the carrier assembly.
e. Remove two bearings (31) from the planetary gear.
9/13
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 22. Repeat Steps 21.a through 21.e for the other two planetary gears.
Illustration 20 g00781730
23. Use two people to remove gear (33). The weight of gear is approximately 41 kg (90 lb).
Illustration 21 g00781807
24. Remove O-ring seal (34).
Illustration 22 g01147650
25. Remove bolts (35A) and plates (35B).
10/13
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engin...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 23 g01147651
26. Use Tooling (G) to remove dowel (37) from stopper plate (35).
Illustration 24 g01147759
27. Secure Tooling (D) to stopper plate (35). Use Tooling (D) to remove stopper plate (35).
Illustration 25 g01147930
28. Use Tooling (E) and a suitable lifting device to remove housing (36). The weight of housing
(36) is approximately 100 kg (220 lb).
11/13
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engin...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 26 g01147951
29. Remove Duo-Cone seal (39A) from housing (38).
Illustration 27 g01147975
Illustration 28 g01147934
30. Remove Duo-Cone seal (39B) from housing (36).
31. Use Tooling (F) in order to remove bearings (40) and (41) from housing (36).
32. If necessary, remove the final drive sprocket from the sprocket housing. Refer to
Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
12/13
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engin...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D L EXCAVATOR AZP
Configuration: 325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8646-22 Publication Date -01/02/2015 Date Updated -12/09/2018
i03949150
Final Drive - Assemble
SMCS - 4050-016
S/N - A3R1-UP
S/N - AZP1-UP
S/N - BFC1-UP
S/N - BYS1-UP
S/N - CZF1-UP
S/N - DBH1-UP
S/N - DJF1-UP
S/N - DTZ1-UP
S/N - EBM1-UP
S/N - EJC1-UP
S/N - GBR1-UP
S/N - GPB1-UP
S/N - GPK1-UP
S/N - JAT1-UP
S/N - JHJ1-UP
S/N - JJG1-UP
1/15
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
D 138-7574 Link Bracket 2
G 126-3994 Duo-Cone Seal Installer 1
H 5P-3931 Anti-Seize Compound
F 1U-8846 Gasket Sealant
Note: Cleanliness is an important factor. Before assembly, all parts should be cleaned in
cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry
parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If
any parts are worn or damaged, use new parts for replacement. All disassembly and all
assembly procedures must be performed on a clean work surface and in a clean hydraulic
area. Keep cleaned parts covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have
the same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound
during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
1. Install the final drive sprocket if the sprocket was removed from the main housing.
2. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Illustration 1 g00708215
3. Apply Tooling (H) to the outer diameter of the bearings.
4. Install bearings (32) and (33) in main housing (18) with a suitable press.
5. Make sure that bearing (32) and bearing (33) contact the counterbore in the main housing.
6. Use the following procedure to preload the bearings and determine the correct thickness of
shims.
3/15
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 2 g00713058
a. Fasten Tooling (D) and a suitable lifting device to main housing (18) . Install the main
housing on the motor housing.
b. Put the main housing and the motor housing in a suitable press.
Illustration 3 g00709278
(a) Bearing surface
(b) Housing surface
c. Use a suitable press and a spacer in order to apply a load of 4000 kg (8818.5 lb) on
the bearings. Rotate the housing in order to seat the bearings.
d. Reduce the load on the bearings to 1000 ± 100 kg (2204.6 ± 220.5 lb).
e. Use a depth micrometer in order to measure the step length between the bearing
surface and the housing surface. Take measurements at several different locations
around the housing. Compute the average of the measured dimensions and record the
number. Call this Dimension (Y) .
4/15
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
29. Illustration 4 g00709276
f. Use a depth micrometer in order to measure the step length of the coupling gear (26) .
Take measurements at several different locations around the gear. Compute the
average of the measured dimensions and record the number. Call this Dimension (X) .
g. The thickness of the shims is equal to (X - Y) ± 0.05 mm (0.002 inch).
Note: Use no more than two shims. If two shims are required, install the thinner shim
next to the gear.
h. Remove the main housing from the motor housing.
Illustration 5 g01021370
7. Use Tooling (G) in order to install Duo-Cone seal (31) in main housing (18) . Refer to
Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contact the seals must be clean and dry. After
installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal seals.
5/15
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 6 g01021371
8. Use Tooling (G) in order to install Duo-Cone seal (29) in motor housing (28) .
Illustration 7 g00708214
9. Apply Tooling (H) to the surfaces that contact pins (30) .
10. Install alignment pins (30) .
Note: Do not damage the Duo-Cone seals in the main housing or in the motor housing
during the assembly of the two components. After installation of the main housing on the
motor housing, there will be a small gap between the components. The gap is caused by the
Duo-Cone seals. This gap will be eliminated during installation of gear (26) .
6/15
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Illustration 8 g00713058
11. Fasten Tooling (D) and a suitable lifting device to main housing (18) . Install the main
housing on the motor housing.
Illustration 9 g00708211
12. Install shims (27) that were determined in Step 6.g in the main housing.
Note: If two shims are required, install the thinner shim next to the gear.
7/15
325D & 325D L Excavators AZP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...