This document provides instructions to remove and disassemble components of the rocker shaft and pushrods on a 325B L excavator powered by a 3116 engine. The summary is as follows:
1) Remove the valve mechanism cover, rocker shaft assembly bolts, and rocker shaft assembly to access the pushrods and rocker arms.
2) Remove the pushrods and individual rocker arms and inspect the rocker shaft assembly and rocker arms.
3) To disassemble further, remove the support bracket and inspect bearings and buttons on the unit injector rocker arm.
Caterpillar cat 325 b l excavator (prefix 5bs) service repair manual (5bs0000...fjjskekdmme
This document provides instructions for removing and installing the rocker shaft and pushrods on a 325B L excavator engine. It describes removing the valve mechanism cover, loosening the rocker arm adjustment screws, removing bolts and the rocker shaft assembly from the cylinder head. It also details installing the rocker shaft by positioning it in the engine and lining up the pushrods with the rocker arms, installing bolts, adjusting valve lash, and reinstalling the valve mechanism cover.
Caterpillar cat 325 b ln excavator (prefix 5bs) service repair manual (5bs000...fjjskekdmme
This document provides instructions for removing and installing a cylinder head on a 325B L & 325B LN Excavator powered by a 3116 engine. The removal procedure involves detaching various components from the engine and lifting the cylinder head off using a lifting device. The installation procedure specifies cleaning the mating surfaces and installing a new cylinder head gasket before lowering the cylinder head back onto the cylinder block.
Caterpillar cat 325 b ln excavator (prefix 8fn) service repair manual (8fn000...fjsjjekdkme
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...fjsjjekdkme
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...f98soeodidkdk
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar Cat 325B and 325B LN Excavator (Prefix 8FN) Service Repair Manual...yan77xunhao
This document provides instructions for removing and servicing components of the rocker shaft and cylinder head on a 325B and 325B LN Excavator powered by a 3116 engine. The procedures include removing the rocker shaft assembly, disassembling the rocker shaft, inspecting components, assembling the rocker shaft, installing the rocker shaft and pushrods, and removing the cylinder head. Detailed steps are outlined along with required tools and safety notices to keep parts clean and contain fluids.
Caterpillar cat 325 b ln excavator (prefix 8fn) service repair manual (8fn000...f98soeodidkdk
This document provides instructions for removing and servicing components of the rocker shaft and cylinder head on a 325B and 325B LN Excavator powered by a 3116 engine. The procedures include removing the rocker shaft assembly, disassembling the rocker shaft, inspecting components, assembling the rocker shaft, installing the rocker shaft and pushrods, and removing the cylinder head. Detailed steps are provided along with illustrations to guide the technician through the process while maintaining cleanliness and proper torque specifications.
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 b l excavator (prefix 5bs) service repair manual (5bs0000...fjjskekdmme
This document provides instructions for removing and installing the rocker shaft and pushrods on a 325B L excavator engine. It describes removing the valve mechanism cover, loosening the rocker arm adjustment screws, removing bolts and the rocker shaft assembly from the cylinder head. It also details installing the rocker shaft by positioning it in the engine and lining up the pushrods with the rocker arms, installing bolts, adjusting valve lash, and reinstalling the valve mechanism cover.
Caterpillar cat 325 b ln excavator (prefix 5bs) service repair manual (5bs000...fjjskekdmme
This document provides instructions for removing and installing a cylinder head on a 325B L & 325B LN Excavator powered by a 3116 engine. The removal procedure involves detaching various components from the engine and lifting the cylinder head off using a lifting device. The installation procedure specifies cleaning the mating surfaces and installing a new cylinder head gasket before lowering the cylinder head back onto the cylinder block.
Caterpillar cat 325 b ln excavator (prefix 8fn) service repair manual (8fn000...fjsjjekdkme
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...fjsjjekdkme
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...f98soeodidkdk
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar Cat 325B and 325B LN Excavator (Prefix 8FN) Service Repair Manual...yan77xunhao
This document provides instructions for removing and servicing components of the rocker shaft and cylinder head on a 325B and 325B LN Excavator powered by a 3116 engine. The procedures include removing the rocker shaft assembly, disassembling the rocker shaft, inspecting components, assembling the rocker shaft, installing the rocker shaft and pushrods, and removing the cylinder head. Detailed steps are outlined along with required tools and safety notices to keep parts clean and contain fluids.
Caterpillar cat 325 b ln excavator (prefix 8fn) service repair manual (8fn000...f98soeodidkdk
This document provides instructions for removing and servicing components of the rocker shaft and cylinder head on a 325B and 325B LN Excavator powered by a 3116 engine. The procedures include removing the rocker shaft assembly, disassembling the rocker shaft, inspecting components, assembling the rocker shaft, installing the rocker shaft and pushrods, and removing the cylinder head. Detailed steps are provided along with illustrations to guide the technician through the process while maintaining cleanliness and proper torque specifications.
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Clark C500, Y180 Forklift Service Repair Manual.pdfdjdksmmdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and lists parts, components, and procedures for repair and maintenance. Copyrighted material is not to be distributed. The index includes sections on engines, transmissions, hydraulics, electrical systems, brakes, steering and other components. Safety practices and proper maintenance procedures are outlined to avoid injury and ensure safe operation.
Clark C500, Y250S Forklift Service Repair Manual.pdfdjdksmmdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and should not be distributed. The document contains diagrams and descriptions of various forklift components and systems, grouped by number. Safety warnings and instructions for safe maintenance practices are also provided.
The document provides maintenance and safety information for a Clark lift truck model SM-560. It includes sections on safety signs and messages, user safe maintenance practices, and a planned maintenance program. The planned maintenance program outlines periodic inspections and maintenance tasks that should be performed, including inspecting nameplates, wheels and tires, controls, brakes, steering, batteries, and mechanisms. It stresses the importance of a clean lift truck and testing all functions before returning the truck to operation.
Clark TMG 12-25 Forklift Service Repair Manual.pdfdjdksmmdmd
This document is a service manual for Clark forklifts that contains information on safely maintaining the forklifts. It includes sections on safety procedures, periodic maintenance schedules, specifications for various parts, and procedures for servicing components such as motors, hydraulics, brakes, steering, and other systems. The manual uses a standardized grouping and numbering system to organize the content and make specific information easy to locate.
Clark TMG 13-20X Forklift Service Repair Manual.pdfdjdksmmdmd
This document provides a summary of safe maintenance practices for industrial trucks. It discusses safety signs and messages used in service manuals. Proper ventilation, fire safety, and authorized personnel are important. Before working on a truck, raise the wheels, disconnect the battery, and check for fuel and electrical hazards. Replacements parts must meet manufacturer standards. Modifications require approval. Overall, maintenance should follow manufacturer procedures to ensure safety.
Komatsu SK815-5 Skid Steer Loader Service Repair Manual (SN 37BF00902 and up)...djdksmmdmd
This shop manual provides instructions for servicing Komatsu skid-steer loaders models SK714-5, SK815-5, and SK815-5 turbo. It is divided into sections covering the machine's structure and function, testing and adjusting procedures, disassembly and assembly instructions, and maintenance standards. Safety precautions are prominently featured to ensure workers' safety during repair operations.
John Deere Alternators & Starter Motors Service Repair Manual.pdfdjdksmmdmd
This document is a Component Technical Manual from Deere & Company that provides service information for alternators and starter motors. It contains sections on safety, general information, and electrical system basics. The safety section outlines proper procedures and precautions for working on electrical components, including preventing battery explosions, handling fluids safely, and wearing protective equipment.
John Deere 12PC Walk-Behind Mower Service Repair Manual.pdfdjdksmmdmd
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications for various mower models, repair specifications for engines and components, information on fuels and lubricants, and locations for serial numbers. The document outlines sections on general information, engine repair, fuel and air systems, electrical systems, power trains, tests and adjustments, and miscellaneous repair items. It provides technicians with the information needed to service the components, diagnose issues, and perform repairs on the mowers.
John Deere 12PB Walk-Behind Mower Service Repair Manual.pdfdjdksmmdmd
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications for various mower models, repair specifications for engines and components, information on fuels and lubricants, and locations for identifying serial numbers. The document outlines sections for engine repair, fuel/air systems, electrical systems, power trains, tests and adjustments, and miscellaneous repairs. It provides technicians with information needed for diagnosis, repair, and maintenance of the mowers.
John Deere 5E 2BV Blower Service Repair Manual.pdfdjdksmmdmd
The document provides specifications for the 5E and 2BV blowers, including engine details like displacement, bore, stroke, compression ratio, carburetor, lubrication, fuel, idle and operating speeds, starter, ignition system, spark plug, magneto air gap, and fuel tank capacities. It also lists the blower type as centrifugal and single stage.
John Deere 3-179D OEM Engine Service Repair Manual.pdfdjdksmmdmd
This document provides an overview and table of contents for a technical manual covering 300 Series OEM Engines. It includes:
- Sections covering the engine and its components, auxiliary systems, electrical systems, sheet metal, PTO drive, and system testing.
- An index listing components and procedures alphabetically to aid navigation.
- Specification tables for torque values and engine data.
The manual is intended as a reference for experienced technicians servicing these engines, with concise instructions and specifications rather than theoretical background.
This document provides specifications, maintenance schedules, adjustment procedures, and safety information for Clark PT-5, PT-7, PTT-5, and PTT-7 trucks. It outlines an essential planned maintenance program to keep the trucks safely operating, including inspections, operational checks, cleaning, lubrication, and adjustments. The document emphasizes safety practices for maintenance, such as raising the wheels, disconnecting power, and using blocks before working under lifted components.
Kubota BX1500D Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions for using a parts book for an engine. It explains the column headings in parts book pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included and what they represent. An example page from the parts book is then shown listing the specific parts for an engine with the corresponding information.
Clark EPG 15-18 Forklift Service Repair Manual.pdfdjdksmmdmd
This document is a service manual for Clark forklifts that contains information on safely maintaining the forklifts. It includes sections on safety procedures, periodic maintenance schedules, specifications for parts, and procedures for servicing various systems of the forklift such as the battery, wiring, motors, brakes, hydraulics, tilt cylinders, and more. The document uses a standardized grouping and numbering system to organize the content and make specific sections and pages easy to locate.
Kubota BX2230D Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes that may be included and their meanings. The remainder of the document lists specific part numbers and descriptions for a BX2230D tractor organized by system or component.
Kubota L35 Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions and definitions for parts books. It explains that the heading on parts pages will match the picture page. It defines the column headings for part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes that may be included and their meanings. Finally, it provides an index of all product parts for reference L35 and lists the relevant parts book for each item.
Kubota G4200H Lawn mower Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions for parts books, including definitions of column headings in parts number pages and notes about country codes. It then provides a sample page from a parts book for a G4200H product that lists over 200 individual part numbers, descriptions, quantities, serial number ranges, interchangeability, remarks and weights.
Komatsu SK714-5 Skid Steer Loader Service Repair Manual (SN 37AF01876 and up)...djdksmmdmd
This document provides shop manual instructions for adjusting valve clearance on Komatsu skid-steer loaders models SK714-5, SK815-5, and SK815-5 turbo. The instructions include removing covers to access the valves, rotating the drive shaft to specific positions, checking valve clearance with feeler gauges, adjusting clearance by turning screws, and reassembling covers. Clearance specifications and tightening torques are provided. The document also provides a zero setting procedure for the SK815-5 turbo model before performing the clearance adjustment.
John Deere Yanmar Engines 322, F912, F932 Service Repair Manual.pdfdjdksmmdmd
This document is a component technical manual for Yanmar gasoline engines. It contains instructions for repairing engines, fuel systems, and electrical systems. It also includes theory of operation, diagnostic procedures, and testing procedures. The manual should be used along with the machine's technical manual for information on removing and installing the engine, and accessing engine components. The manual emphasizes safety and provides illustrated, step-by-step instructions for diagnosis and repair of engine systems.
John Deere POWERTECH 4.5L & 6.8L Diesel Engines Base Engine Service Repair Ma...djdksmmdmd
This document provides instructions for servicing Powertech 4.5L and 6.8L diesel engines. It outlines five technical manuals that cover different aspects of the engines, with this document focusing on the base engine. The introduction provides safety information and explains how to use the manual, including cleaning the engine before repair. It directs technicians to companion manuals for fuel system repair, operation and diagnostics based on the specific fuel system for the engine being serviced.
Clark C500, Y180 Forklift Service Repair Manual.pdfdjdksmmdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and lists parts, components, and procedures for repair and maintenance. Copyrighted material is not to be distributed. The index includes sections on engines, transmissions, hydraulics, electrical systems, brakes, steering and other components. Safety practices and proper maintenance procedures are outlined to avoid injury and ensure safe operation.
Clark C500, Y250S Forklift Service Repair Manual.pdfdjdksmmdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and should not be distributed. The document contains diagrams and descriptions of various forklift components and systems, grouped by number. Safety warnings and instructions for safe maintenance practices are also provided.
The document provides maintenance and safety information for a Clark lift truck model SM-560. It includes sections on safety signs and messages, user safe maintenance practices, and a planned maintenance program. The planned maintenance program outlines periodic inspections and maintenance tasks that should be performed, including inspecting nameplates, wheels and tires, controls, brakes, steering, batteries, and mechanisms. It stresses the importance of a clean lift truck and testing all functions before returning the truck to operation.
Clark TMG 12-25 Forklift Service Repair Manual.pdfdjdksmmdmd
This document is a service manual for Clark forklifts that contains information on safely maintaining the forklifts. It includes sections on safety procedures, periodic maintenance schedules, specifications for various parts, and procedures for servicing components such as motors, hydraulics, brakes, steering, and other systems. The manual uses a standardized grouping and numbering system to organize the content and make specific information easy to locate.
Clark TMG 13-20X Forklift Service Repair Manual.pdfdjdksmmdmd
This document provides a summary of safe maintenance practices for industrial trucks. It discusses safety signs and messages used in service manuals. Proper ventilation, fire safety, and authorized personnel are important. Before working on a truck, raise the wheels, disconnect the battery, and check for fuel and electrical hazards. Replacements parts must meet manufacturer standards. Modifications require approval. Overall, maintenance should follow manufacturer procedures to ensure safety.
Komatsu SK815-5 Skid Steer Loader Service Repair Manual (SN 37BF00902 and up)...djdksmmdmd
This shop manual provides instructions for servicing Komatsu skid-steer loaders models SK714-5, SK815-5, and SK815-5 turbo. It is divided into sections covering the machine's structure and function, testing and adjusting procedures, disassembly and assembly instructions, and maintenance standards. Safety precautions are prominently featured to ensure workers' safety during repair operations.
John Deere Alternators & Starter Motors Service Repair Manual.pdfdjdksmmdmd
This document is a Component Technical Manual from Deere & Company that provides service information for alternators and starter motors. It contains sections on safety, general information, and electrical system basics. The safety section outlines proper procedures and precautions for working on electrical components, including preventing battery explosions, handling fluids safely, and wearing protective equipment.
John Deere 12PC Walk-Behind Mower Service Repair Manual.pdfdjdksmmdmd
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications for various mower models, repair specifications for engines and components, information on fuels and lubricants, and locations for serial numbers. The document outlines sections on general information, engine repair, fuel and air systems, electrical systems, power trains, tests and adjustments, and miscellaneous repair items. It provides technicians with the information needed to service the components, diagnose issues, and perform repairs on the mowers.
John Deere 12PB Walk-Behind Mower Service Repair Manual.pdfdjdksmmdmd
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications for various mower models, repair specifications for engines and components, information on fuels and lubricants, and locations for identifying serial numbers. The document outlines sections for engine repair, fuel/air systems, electrical systems, power trains, tests and adjustments, and miscellaneous repairs. It provides technicians with information needed for diagnosis, repair, and maintenance of the mowers.
John Deere 5E 2BV Blower Service Repair Manual.pdfdjdksmmdmd
The document provides specifications for the 5E and 2BV blowers, including engine details like displacement, bore, stroke, compression ratio, carburetor, lubrication, fuel, idle and operating speeds, starter, ignition system, spark plug, magneto air gap, and fuel tank capacities. It also lists the blower type as centrifugal and single stage.
John Deere 3-179D OEM Engine Service Repair Manual.pdfdjdksmmdmd
This document provides an overview and table of contents for a technical manual covering 300 Series OEM Engines. It includes:
- Sections covering the engine and its components, auxiliary systems, electrical systems, sheet metal, PTO drive, and system testing.
- An index listing components and procedures alphabetically to aid navigation.
- Specification tables for torque values and engine data.
The manual is intended as a reference for experienced technicians servicing these engines, with concise instructions and specifications rather than theoretical background.
This document provides specifications, maintenance schedules, adjustment procedures, and safety information for Clark PT-5, PT-7, PTT-5, and PTT-7 trucks. It outlines an essential planned maintenance program to keep the trucks safely operating, including inspections, operational checks, cleaning, lubrication, and adjustments. The document emphasizes safety practices for maintenance, such as raising the wheels, disconnecting power, and using blocks before working under lifted components.
Kubota BX1500D Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions for using a parts book for an engine. It explains the column headings in parts book pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included and what they represent. An example page from the parts book is then shown listing the specific parts for an engine with the corresponding information.
Clark EPG 15-18 Forklift Service Repair Manual.pdfdjdksmmdmd
This document is a service manual for Clark forklifts that contains information on safely maintaining the forklifts. It includes sections on safety procedures, periodic maintenance schedules, specifications for parts, and procedures for servicing various systems of the forklift such as the battery, wiring, motors, brakes, hydraulics, tilt cylinders, and more. The document uses a standardized grouping and numbering system to organize the content and make specific sections and pages easy to locate.
Kubota BX2230D Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes that may be included and their meanings. The remainder of the document lists specific part numbers and descriptions for a BX2230D tractor organized by system or component.
Kubota L35 Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions and definitions for parts books. It explains that the heading on parts pages will match the picture page. It defines the column headings for part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes that may be included and their meanings. Finally, it provides an index of all product parts for reference L35 and lists the relevant parts book for each item.
Kubota G4200H Lawn mower Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions for parts books, including definitions of column headings in parts number pages and notes about country codes. It then provides a sample page from a parts book for a G4200H product that lists over 200 individual part numbers, descriptions, quantities, serial number ranges, interchangeability, remarks and weights.
Komatsu SK714-5 Skid Steer Loader Service Repair Manual (SN 37AF01876 and up)...djdksmmdmd
This document provides shop manual instructions for adjusting valve clearance on Komatsu skid-steer loaders models SK714-5, SK815-5, and SK815-5 turbo. The instructions include removing covers to access the valves, rotating the drive shaft to specific positions, checking valve clearance with feeler gauges, adjusting clearance by turning screws, and reassembling covers. Clearance specifications and tightening torques are provided. The document also provides a zero setting procedure for the SK815-5 turbo model before performing the clearance adjustment.
John Deere Yanmar Engines 322, F912, F932 Service Repair Manual.pdfdjdksmmdmd
This document is a component technical manual for Yanmar gasoline engines. It contains instructions for repairing engines, fuel systems, and electrical systems. It also includes theory of operation, diagnostic procedures, and testing procedures. The manual should be used along with the machine's technical manual for information on removing and installing the engine, and accessing engine components. The manual emphasizes safety and provides illustrated, step-by-step instructions for diagnosis and repair of engine systems.
John Deere POWERTECH 4.5L & 6.8L Diesel Engines Base Engine Service Repair Ma...djdksmmdmd
This document provides instructions for servicing Powertech 4.5L and 6.8L diesel engines. It outlines five technical manuals that cover different aspects of the engines, with this document focusing on the base engine. The introduction provides safety information and explains how to use the manual, including cleaning the engine before repair. It directs technicians to companion manuals for fuel system repair, operation and diagnostics based on the specific fuel system for the engine being serviced.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930098
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of components of the rocker shaft, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8267, "Rocker Arms and Rocker Arm Shafts for
3114 and 3116 Engines".
1/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00629575
1. Loosen all rocker arm adjustment screws (3).
2. Remove bolts (1) from the rocker shaft assembly (2).
3. Remove rocker shaft assembly (2) from the cylinder head.
4. Repeat the procedure for each rocker shaft assembly.
5. Remove the pushrods.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:29:00 UTC+0800 2020
2/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930139
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-0083 Emery Polishing Paper 1
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of components of the rocker shaft, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8267, "Rocker Arms and Rocker Arm Shafts for
3114 and 3116 Engines".
1/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00629612
1. Remove support bracket (1) from rocker shaft assembly (4).
2. Remove valve rocker arms (2) and unit injector rocker arm (3) from rocker shaft assembly
(4).
Note: Do not force the rocker arms from the rocker shaft assembly. If necessary, use a piece
of Tooling (A) to lightly buff the surface of the shaft to aid in removal .
3. Check the adjustment screws on valve rocker arms (2) and unit injector rocker arm (3) for
damage.
4. Inspect rocker shaft assembly (4) for scratches and cracks.
Illustration 2 g00630277
5. Inspect bearing (5) on unit injector rocker arm (3). The bore in the rocker arm is
24.808 ± 0.20 mm (0.9767 ± 0.0079 inch). Refer to Specification, "Valve Rocker Arm and
Lifters". Replace the bearing, if necessary.
6. Ensure that button (6) on unit injector rocker arm (3) is not damaged. Also ensure that the
retaining ring for button (6) is in place.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:29:56 UTC+0800 2020
2/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930194
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of components of the rocker shaft, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8267, "Rocker Arms and Rocker Arm Shafts for
3114 and 3116 Engines".
1/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g00630277
1. Install button (6) and the retaining ring, if necessary.
2. Place clean engine oil on a new bearing (5) prior to installation.
3. Ensure that the oil hole in bearing (5) is aligned with the oil hole in the rocker arm. Hone
the bearing, if necessary. Refer to the Specifications Module for the correct dimensions.
Illustration 2 g00629612
4. Lubricate rocker shaft assembly (4) with clean engine oil.
5. Install valve rocker arms (2) and unit injector rocker arm (3) on rocker shaft assembly (4).
6. Install support bracket (1) on rocker shaft assembly (4).
End By:
a. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:30:52 UTC+0800 2020
2/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02736495
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 146-2597 Pushrod Holder 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of components of the rocker shaft, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8267, "Rocker Arms and Rocker Arm Shafts for
3114 and 3116 Engines".
1. Install the pushrods in the engine. The base of the pushrod should be in the seat of the
pushrod lifter.
2. Install Tooling (A).
1/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g00629575
3. Position rocker shaft assembly (2) in the engine. Line up the pushrods with the rocker arms.
4. Install bolts (1) in rocker shaft assembly (2). Tighten the bolts to a torque of 28 ± 7 N·m
(21 ± 5 lb ft).
5. Remove Tooling (A) from the pushrods.
6. Adjust the valve lash on all of the adjustment screws. Refer to Testing and Adjusting,
"Engine Valve Lash - Inspect/Adjust".
7. Repeat the procedure for the remaining rocker shaft assemblies.
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:31:48 UTC+0800 2020
2/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01935828
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
a. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
b. Remove the governor. Refer to Disassembly and Assembly, "Governor - Remove".
c. Remove the fuel control linkage. Refer to Disassembly and Assembly, "Fuel Injection
Control Linkage - Remove".
d. Remove the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
e. Remove the water temperature regulator housing. Refer to Disassembly and Assembly,
"Water Temperature Regulator Housing - Remove and Install".
f. Remove the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold -
Remove".
g. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: For information on the reusability of the cylinder head, refer to Guideline For Reusable
Parts And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114,
3116, and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 1 g01007597
Typical example
1. Attach a suitable lifting device to the cylinder head.
2/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g00654709
2. Remove bolts (1) and (2) that hold the cylinder head to the cylinder block. Carefully remove
the cylinder head from the cylinder block. The cylinder head for the 3116 engine weighs
approximately 85 kg (187 lb).
Illustration 3 g00611342
3. Remove cylinder head gasket (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:32:44 UTC+0800 2020
3/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i04147334
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4876 Lubricant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the cylinder head, refer to Guideline For Reusable
Parts And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114,
3116, and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
1. Thoroughly clean the mating surfaces of the cylinder head and the cylinder block.
1/5
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00611342
Typical example
2. Install a new cylinder head gasket (3) .
Note: For information on the cylinder head gasket for 3116 engines, refer to Special
Instruction, SEHS9395, "3116 Cylinder Head Gasket Usage".
Illustration 2 g01007597
Typical example
Note: To avoid damage to the cylinder head gasket, use guide bolts of an appropriate size to
install the cylinder head.
3. Attach a suitable lifting device to the cylinder head. Position the cylinder head assembly
onto the dowels in the cylinder block. Lower the cylinder head onto the cylinder block.
2/5
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00654709
4. Inspect the condition of cylinder head bolts (1) and (2) . For information on the reusability
of the bolts, refer to Guideline For Reusable Parts And Salvage Operations, SEBF8301,
"Inspection and Reuse of Critical Fasteners Used in All Engines". Replace cylinder head
bolts (1) and (2) , if necessary.
5. Lubricate cylinder head bolts (1) and (2) and both sides of the washers with Tooling (A) .
Install cylinder head bolts (1) and (2) . Follow Step 6 for the correct tightening procedure.
Illustration 4 g00641677
3114 Cylinder head
3/5
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 5 g00611358
6. Tighten the cylinder head bolts according to the following procedure:
7. Tighten bolts (1) through bolt (14) in a numerical sequence to a torque of 300 ± 15 N·m
(221 ± 11 lb ft).
8. Loosen bolts (1) through bolt (14) to a torque of 0 N·m.
9. Tighten bolts (1) through bolt (14) again in a numerical sequence to a torque of 130 ± 15
N·m (96 ± 11 lb ft).
10. Retighten bolts (1) through bolt (14) again in a numerical sequence to a torque of 130 ± 15
N·m (96 ± 11 lb ft).
11. Turn bolts (1) through bolt (14) by numerical sequence an additional 90° (1/4 turn).
12. Tighten bolt (15) through bolt (20) in a numerical sequence to a torque of 55 ± 7 N·m (41 ±
5 lb ft).
End By:
a. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
b. Install the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold - Install".
c. Install the water temperature regulator housing. Refer to Disassembly and Assembly,
"Water Temperature Regulator Housing- Remove and Install".
d. Install the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Install".
e. Install the fuel control linkage. Refer to Disassembly and Assembly, "Fuel Injection Control
Linkage - Install".
f. Install the governor. Refer to Disassembly and Assembly, "Governor - Install".
g. Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove
and Install".
4/5
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:33:39 UTC+0800 2020
5/5
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930413
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/4
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Dispose of all fluids according to local regulations and mandates.
Note: For information on reusability of components of the lifter group, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8264, "Camshaft Roller Followers Used in 3114
and 3116 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8067,
"Slipper Followers and Camshaft Roller Followers".
Illustration 1 g00747310
1. Remove bolts (1) from cover (2).
2. Carefully remove cover (2) and the gasket.
Note: It may be necessary to remove the governor in order to remove the cover at the front
of the engine.
Illustration 2 g00629677
3. Remove bolts (4), lifter shaft (5), and lifters (3) from cover (2).
Installation Procedure
2/4
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of components of the lifter group, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8264, "Camshaft Roller Followers Used in 3114
and 3116 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8067,
"Slipper Followers and Camshaft Roller Followers".
Illustration 3 g00629677
1. Position lifters (3) and lifter shaft (5) on cover (2). Install bolts (4).
Illustration 4 g00747310
2. Position the gasket and cover (2) on the engine.
3. Install bolts (1) in cover (2).
End By:
3/4
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. a. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:34:35 UTC+0800 2020
4/4
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930426
Camshaft - Remove
SMCS - 1210-011
Removal Procedure
Start By:
a. Remove the governor. Refer to Disassembly and Assembly, "Governor - Remove".
b. Remove the side covers. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
c. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: For information on reusability of the camshaft, refer to Guideline For Reusable Parts And
Salvage Operations, SEBF8097, "Camshaft Measurement", Guideline For Reusable Parts And
Salvage Operations, SEBF8146, "Visual Inspection of Camshafts", and Guideline For Reusable
Parts And Salvage Operations, SEBF8251, "Specifications for Measurement of Camshafts in
3114/3116 Engines". For information on reusability of the camshaft gear, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
Note: The air compressor was removed in order to accommodate the engine repair stand.
Note: It is not necessary to remove the cylinder head for removal of the camshaft.
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. Install the timing
bolt in the flywheel. This is for timing during installation.
Illustration 1 g01007643
Typical example
2. Ensure that timing mark (1) on the camshaft gear is aligned with timing mark (2) on the
idler gear.
2/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 2 g01007645
3. Remove bolts (4) and camshaft retainer plate (6).
4. Remove camshaft gear (5) and camshaft (3) from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:35:31 UTC+0800 2020
3/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01936378
Camshaft - Install
SMCS - 1210-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of the camshaft, refer to Guideline For Reusable Parts And
Salvage Operations, SEBF8097, "Camshaft Measurement", Guideline For Reusable Parts And
Salvage Operations, SEBF8146, "Visual Inspection of Camshafts", and Guideline For Reusable
Parts And Salvage Operations, SEBF8251, "Specifications for Measurement of Camshafts in
3114/3116 Engines". For information on reusability of the camshaft gear, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
1. Lubricate the camshaft and the camshaft bearings with clean engine oil.
1/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g01007645
2. Carefully install camshaft (3) and camshaft gear (5) in the engine.
NOTICE
When installing the camshaft, make sure the number one cylinder is at
top center of the compression stroke with the timing bolt installed in
the flywheel. The camshaft timing is very important. The timing mark
on the camshaft drive gear must line up with the timing mark on the
idler gear. Refer to the Specifications Manual for more information.
Illustration 2 g01007643
Typical example
3. Ensure that timing mark (1) on the camshaft gear is aligned with timing mark (2) on the
idler gear.
2/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 4. Install camshaft retainer plate (6) and bolts (4).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
b. Install the side cover. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
c. Install the governor. Refer to Disassembly and Assembly, "Governor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:36:27 UTC+0800 2020
3/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...