This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 track type excavator (prefix 7 cj) service repair manual ...hfjsekekmmd
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...hfjsekekmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are given to keep parts clean and refer to other documents for guidance on determining if parts can be reused. The document is from a service repair manual for the excavator model.
The document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325-A excavator. It lists the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and installing new inserts. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fuusejkddmmd3e
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fuusejkddmmd3e
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...dujkdksmdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar cat 325 track type excavator (prefix 7 cj) service repair manual ...hfjsekekmmd
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...hfjsekekmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are given to keep parts clean and refer to other documents for guidance on determining if parts can be reused. The document is from a service repair manual for the excavator model.
The document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325-A excavator. It lists the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and installing new inserts. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fuusejkddmmd3e
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fuusejkddmmd3e
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...dujkdksmdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...jdksmmdmdd
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...dujkdksmdmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...jdksmmdmdd
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fjkdksmmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...jdfjskekmdme
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325L excavator engine:
1. Use a valve guide driver tool to remove the old valve guides from the cylinder head. Keep all parts clean from contaminants.
2. Position the new inlet valve guides in the cylinder head and use a driver tool and guide collar to fully install them. Repeat for the exhaust valve guides.
3. Reinstall the inlet and exhaust valves following the specified procedure using a valve spring compressor tool.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...hfjsekekmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...jdfjskekmdme
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It lists the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts and install new ones, ensuring the parts are clean from contaminants. References are provided for determining if valve seats can be reused.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325L excavator engine:
1. Use a valve guide driver tool to remove the old valve guides from the cylinder head. Keep all parts clean from contaminants.
2. Position the new inlet valve guides in the cylinder head and use a driver tool and guide collar to fully install them. Repeat for the exhaust valve guides.
3. Reinstall the inlet and exhaust valves following the specified procedure using a valve spring compressor tool.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...fujsekksmem
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are listed to keep parts clean and refer to other documents for guidance on determining if parts can be reused.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...jdfjskekmdme
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by noting the required tools and removing previous components like the rocker arm shaft and front cover. The camshaft is then removed by loosening bolts while aligning timing marks and lifting it out. Reinstallation requires aligning timing marks, lubricating the camshaft, and tightening bolts to specified torque to complete the job. Proper cleaning and lubrication are emphasized to prevent premature wear.
Caterpillar cat 330 c excavator (prefix rbh) service repair manual (rbh00001 ...jdfjskekmdme
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing all seals and installing components in the reverse order of disassembly.
- Special tools are required for tasks like removing bearings and installing retaining rings.
Caterpillar cat 330 c excavator (prefix mkm) service repair manual (mkm00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly procedure has 28 steps that remove components like the head, springs, plates, and seals. The assembly procedure reverses these steps and provides notes on cleaning, marking parts, and applying thread lock compounds. It cautions that cleanliness is important and springs can cause injury if not assembled properly.
Caterpillar cat 330 c excavator (prefix mca) service repair manual (mca00001 ...jdfjskekmdme
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Caterpillar cat 330 c excavator (prefix kdd) service repair manual (kdd00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c excavator (prefix jnk) service repair manual (jnk00001 ...jdfjskekmdme
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c excavator (prefix jcd) service repair manual (jcd00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The disassembly process involves removing 28 components from the travel motor in 28 steps, including removing the head, brake piston, rotating assembly, seals, and other internal parts.
2. Cleanliness is important during disassembly and assembly to prevent contamination. All parts should be cleaned and lubricated before assembly.
3. The assembly process reverses the disassembly steps, involving installing 28 components in 28 steps to reassemble the travel motor. Special tools and torque specifications are provided.
More Related Content
Similar to Caterpillar cat 325 l track type excavator (prefix 7cj) service repair manual (7cj00001 and up)
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...jdksmmdmdd
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...dujkdksmdmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...jdksmmdmdd
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fjkdksmmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...jdfjskekmdme
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325L excavator engine:
1. Use a valve guide driver tool to remove the old valve guides from the cylinder head. Keep all parts clean from contaminants.
2. Position the new inlet valve guides in the cylinder head and use a driver tool and guide collar to fully install them. Repeat for the exhaust valve guides.
3. Reinstall the inlet and exhaust valves following the specified procedure using a valve spring compressor tool.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...hfjsekekmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...jdfjskekmdme
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It lists the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts and install new ones, ensuring the parts are clean from contaminants. References are provided for determining if valve seats can be reused.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325L excavator engine:
1. Use a valve guide driver tool to remove the old valve guides from the cylinder head. Keep all parts clean from contaminants.
2. Position the new inlet valve guides in the cylinder head and use a driver tool and guide collar to fully install them. Repeat for the exhaust valve guides.
3. Reinstall the inlet and exhaust valves following the specified procedure using a valve spring compressor tool.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...fujsekksmem
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are listed to keep parts clean and refer to other documents for guidance on determining if parts can be reused.
Similar to Caterpillar cat 325 l track type excavator (prefix 7cj) service repair manual (7cj00001 and up) (15)
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...jdfjskekmdme
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by noting the required tools and removing previous components like the rocker arm shaft and front cover. The camshaft is then removed by loosening bolts while aligning timing marks and lifting it out. Reinstallation requires aligning timing marks, lubricating the camshaft, and tightening bolts to specified torque to complete the job. Proper cleaning and lubrication are emphasized to prevent premature wear.
Caterpillar cat 330 c excavator (prefix rbh) service repair manual (rbh00001 ...jdfjskekmdme
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing all seals and installing components in the reverse order of disassembly.
- Special tools are required for tasks like removing bearings and installing retaining rings.
Caterpillar cat 330 c excavator (prefix mkm) service repair manual (mkm00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly procedure has 28 steps that remove components like the head, springs, plates, and seals. The assembly procedure reverses these steps and provides notes on cleaning, marking parts, and applying thread lock compounds. It cautions that cleanliness is important and springs can cause injury if not assembled properly.
Caterpillar cat 330 c excavator (prefix mca) service repair manual (mca00001 ...jdfjskekmdme
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Caterpillar cat 330 c excavator (prefix kdd) service repair manual (kdd00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c excavator (prefix jnk) service repair manual (jnk00001 ...jdfjskekmdme
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c excavator (prefix jcd) service repair manual (jcd00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The disassembly process involves removing 28 components from the travel motor in 28 steps, including removing the head, brake piston, rotating assembly, seals, and other internal parts.
2. Cleanliness is important during disassembly and assembly to prevent contamination. All parts should be cleaned and lubricated before assembly.
3. The assembly process reverses the disassembly steps, involving installing 28 components in 28 steps to reassemble the travel motor. Special tools and torque specifications are provided.
Caterpillar cat 330 c excavator (prefix jab) service repair manual (jab00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c excavator (prefix haa) service repair manual (haa00001 ...jdfjskekmdme
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing seals and installing components in the reverse order of disassembly.
- Tools required include an adapter, nuts, washers, threaded rod, eyebolt, retaining ring pliers, bearing puller, and thread lock compound.
Caterpillar cat 330 c excavator (prefix gkx) service repair manual (gkx00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) Similarly, it outlines 28 steps for assembly, instructing technicians to replace all seals and gaskets and apply lubricant before reinstalling components in reverse order of disassembly. Cleanliness is emphasized throughout the process.
Caterpillar cat 330 c excavator (prefix gag) service repair manual (gag00001 ...jdfjskekmdme
1) The document provides disassembly and assembly instructions for a 330C excavator travel motor. It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
2) The assembly section lists 29 steps to reassemble the travel motor by replacing components in the reverse order of disassembly. Special tools are required for tasks like removing races and installing seals and rings.
3) Cleanliness is important during disassembly and assembly. Marks should be made to ensure parts are replaced in the same positions. Seal surfaces require compound and components need light oil applied before assembly.
Caterpillar cat 330 c excavator (prefix btm) service repair manual (btm00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It details 28 steps for disassembly, removing components like the head, port plate, springs, brake piston, plates, and bearings. It then details 21 steps for assembly, replacing seals and installing components in the reverse order of disassembly, taking care to mark parts and return them to their original positions. Tools required are also listed.
Caterpillar cat 330 b l excavator (prefix 8tr) service repair manual (8tr0000...jdfjskekmdme
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator including:
1. The cylinder head removal procedure involves removing the fuel injection lines, exhaust manifold, rocker shaft and pushrods.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts in a specific tightening sequence.
3. Removing the spacer plate requires taking out seals and removing the plate from the cylinder head. Installing requires new seals and gaskets and ensuring surfaces are clean.
Caterpillar cat 330 b l excavator (prefix 8sr) service repair manual (8sr0000...jdfjskekmdme
The document provides instructions for removing, disassembling, assembling, and installing a rocker shaft and pushrods on an excavator engine. The removal process involves taking off the valve mechanism cover and then removing six bolts and the rocker shaft assembly. Individual pushrods are also removed after being marked for identification. Disassembly of the rocker shaft requires removing retaining rings, springs, washers and rocker arms. Assembly is the reverse of disassembly and installation involves reinstalling the rocker shaft assembly and pushrods and replacing the valve mechanism cover.
Caterpillar cat 330 b l excavator (prefix 5ls) service repair manual (5ls0000...jdfjskekmdme
The document provides instructions for removing and installing connecting rod bearings, crankshaft main bearings, and the crankshaft on a Caterpillar 330B excavator engine. The procedures include using tools to check bearing clearances, installing bearings dry and oiled, tightening bolts in sequences, and verifying end play. The crankshaft removal requires aligning timing marks, removing caps and nuts, pushing pistons down, lifting the crankshaft out using brackets, and removing gears and seals.
Caterpillar cat 330 b l excavator (prefix 4rs) service repair manual (4rs0000...jdfjskekmdme
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe procedures for removing and installing the cylinder head, rocker shaft and pushrods. Specifically, they outline removing the cylinder head by first removing associated components like the fuel lines, exhaust manifold, and rocker shaft. They then describe loosening bolts and using lifting devices to remove the heavy cylinder head. Procedures are also provided for disassembling, cleaning, inspecting, and reassembling the rocker shaft.
Caterpillar cat 330 b excavator (prefix 9hn) service repair manual (9hn00001 ...jdfjskekmdme
This document provides instructions for removing and installing final drives on an excavator. Key steps include:
1. Releasing hydraulic pressure and removing the track assemblies.
2. Removing bolts and disconnecting hydraulic lines to separate the final drive from the undercarriage frame.
3. Cleaning components and installing new seals before reassembling in reverse order, taking care to properly tighten bolts and reconnect hydraulic components.
Caterpillar cat 330 b excavator (prefix 8tr) service repair manual (8tr00001 ...jdfjskekmdme
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator, including:
- Removing the cylinder head by detaching various lines and manifolds, then lifting it off with a device.
- Installing a new spacer plate gasket and O-rings before positioning the spacer plate on the cylinder head and block.
- Removing and installing water directors by carefully aligning them in the cylinder head.
- Instructions specify cleaning parts thoroughly and applying clean oil to bolts before tightening to specified torques.
Caterpillar cat 330 b excavator (prefix 8sr) service repair manual (8sr00001 ...jdfjskekmdme
The document provides instructions for removing, disassembling, assembling, and installing a rocker shaft and pushrods on an excavator engine. The removal process involves taking off the valve mechanism cover and then removing six bolts and the rocker shaft assembly. Individual pushrods are also removed after being marked for identification. Disassembly of the rocker shaft requires removing retaining rings, springs, washers and rocker arms. Assembly is the reverse of disassembly and installation involves reinstalling the rocker shaft assembly and pushrods and replacing the valve mechanism cover.
Caterpillar cat 330 b excavator (prefix 5ls) service repair manual (5ls00001 ...jdfjskekmdme
The document provides instructions for removing and installing connecting rod bearings, crankshaft main bearings, and the crankshaft on a Caterpillar 330B excavator engine. The procedures include using tools to check bearing clearances, installing bearings dry and oiled, torquing fasteners, and aligning identification marks. The crankshaft removal requires lifting it straight up after removing connecting rods, main bearing caps, and thrust plates.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 7CJ
Configuration: 325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01414226
Inlet Manifold - Install
SMCS - 1058-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00675794
1. Install a new gasket (6) on the cylinder head.
Illustration 2 g00629952
2. Position the air inlet manifold (5) on the engine.
3. Install bolts (4). Tighten the bolts to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
4. Install air inlet elbows (2) on air inlet manifold (5).
5. Install bolts (1) and connect air inlet heater solenoid (3).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:27:05 UTC+0800 2020
2/2
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 7CJ
Configuration: 325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01943334
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
1/5
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g01011225
Note: The following components of the exhaust valves are different from the components of
the inlet valves: spring retainer (2), valve spring (3) and valve (5).
Illustration 2 g01011269
1. Use Tooling (A) to compress valve spring (3). Remove retainer lock (1).
2. Remove Tooling (A).
3. Remove spring retainer (2). Remove valve spring (3).
2/5
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 4. Remove valve seal (4) and valve (5).
5. Repeat Steps 1 through 4 in order to remove the remaining inlet valves and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
3/5
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 3 g01011225
1. Lubricate valve (5) with clean engine oil. Install valve (5) in the cylinder head assembly.
Install new valve seal (4) against the valve guide.
2. Place the following items on the valve stem: valve spring (3) and spring retainer (2).
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
Note: A small amount of grease can be used to hold retainer locks (1) in position during
installation.
4/5
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 4 g01011269
3. Use Tooling (A) to compress valve spring (3). Install retainer lock (1).
4. Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves.
End By:
a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:28:00 UTC+0800 2020
5/5
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 7CJ
Configuration: 325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01961680
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Asseblies 3114, 3116, and
3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162, "Procedure
to Measure and Salvage Cylinder Head Assemblies and Related Components".
1/4
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g00745735
Typical example
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (A) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
B 1U-7792 Guide Collar (1)
1
C 9U-6895 Valve Guide Driver 1
D 149-4008 Guide Collar 1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 2 g00745782
Typical example
1. Position inlet valve guide (1) and tap on the top of inlet valve guide (1). This is done in
order to start inlet valve guide (1) into the cylinder head assembly.
2. Use Tooling (A) and Tooling (B) to install inlet valve guide (1). Install inlet valve guides
(1) until tooling (B) contacts the cylinder head.
3/4
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00745672
Typical example
3. Position exhaust valve guide (2) and tap on the top of exhaust valve guide (2). This is done
in order to start the exhaust valve guide into the cylinder head assembly.
Note: Some of the early engines have inlet valves and exhaust valves that are identical in
size. Use the same specifications and the same tools for both valves. Proceed to Step 4 if the
valves are not the same size.
4. Use Tooling (C) and Tooling (D) to install exhaust valve guide (2). Install inlet valve guides
(2) until tooling (D) contacts the cylinder head.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:28:56 UTC+0800 2020
4/4
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 7CJ
Configuration: 325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929146
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor 1
B(1)
165-5647 Valve Seat Extractor 1
C(1)
6V-4804 Handle 1
D(1)
6V-4192 Threaded Shaft 1
E(1)
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
Illustration 1 g00615519
Illustration 2 g00656459
Note: Replace Tooling (A) with Tooling (B) for the removal of the inlet valve seat insert.
1. Install Tooling (A) in the exhaust valve seat insert.
2. Install Tooling (C) and Tooling (D) in Tooling (A). Hand tighten Tooling (D). Tooling (A)
will expand below the edge of valve seat insert (1).
2/4
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00656462
3. Install Tooling (E) on the cylinder head under Tooling (C). Hold Tooling (D) while you turn
Tooling (C). Remove valve seat insert (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
F 1U-6685 Guide and Insert Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
1. Cool the valve seat inserts for easier installation.
3/4
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g01003799
2. Turn Tooling (F) upside-down and use Tooling (F) and a press to install the valve seat
inserts in the cylinder head assembly.
3. After the valve seat inserts are installed, grind the inserts to the final specification. Refer to
Guideline for Reusable Parts and Salvage Operation, SEBF8218, "Specifications for
Cylinder Head Assemblies 3114, 3116, and 3126 Engines" for the specifications.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:29:52 UTC+0800 2020
4/4
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 7CJ
Configuration: 325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929163
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
Start By:
a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01009468
1. Use Tooling (A) to remove engine oil filter (3).
2. Disconnect the tube assembly for the turbocharger inlet (1) from the engine oil filter base
(4).
3. Remove bolts (2) and the washers that hold engine oil filter base (4) to the cylinder block.
4. Remove engine oil filter base (4) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:30:47 UTC+0800 2020
2/2
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 7CJ
Configuration: 325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929612
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Illustration 1 g01011623
Personal injury can result from being struck by parts propelled by a
released spring force.
1/2
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plugs (1) and (3) from oil filter base (2).
Illustration 2 g01011627
2. Remove springs (4) and valves (6). Remove O-ring seals (5) from plugs (1) and (3). Inspect
the parts for wear or damage. If the parts are worn or damaged, use new parts for
replacement.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:31:43 UTC+0800 2020
2/2
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 7CJ
Configuration: 325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929615
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
Illustration 1 g01011627
1. Install O-ring seals (5) onto plugs (1) and (3). Install valves (6) and springs (4).
1/2
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 2 g01011623
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install plugs (1) and (3) onto oil filter base (2).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:32:39 UTC+0800 2020
2/2
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 7CJ
Configuration: 325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02376426
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01009468
1/3
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 2 g01185803
Illustration 3 g00676791
1. Position the gasket and engine oil filter base (4) on the cylinder block.
2. Install the washers and bolts (2) that hold engine oil filter base (4) to the cylinder block.
Tighten the bolts according to the following procedure:
a. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 15 N·m (11
lb ft).
b. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 28 N·m (21
lb ft).
3. Apply lubricant to new O-ring seal (5) . Install O-ring seal (5) in the fitting on the engine oil
filter base.
4. Connect tube assembly (1) to engine oil filter base (4) .
Note: Never install an oil filter with a wrench. Follow the instructions on the oil filter.
2/3
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 5. Put a coat of fresh oil on the O-ring seal for the engine oil filter. Install engine oil filter (3)
on engine oil filter base (4) by hand.
6. After the O-ring seal contacts engine oil filter base (4) , turn engine oil filter (3) for 3/4 of a
turn.
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 31 22:33:35 UTC+0800 2020
3/3
325, 325L TRACK TYPE EXCAVATORS 7CJ00001-UP (MACHINE) POWERED ...
2020/7/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...