The document provides instructions for removing and installing connecting rod bearings, crankshaft main bearings, and the crankshaft on a Caterpillar 330B excavator engine. The procedures include using tools to check bearing clearances, installing bearings dry and oiled, tightening bolts in sequences, and verifying end play. The crankshaft removal requires aligning timing marks, removing caps and nuts, pushing pistons down, lifting the crankshaft out using brackets, and removing gears and seals.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B L EXCAVATOR 5LS
Configuration: 330B & 330B L Excavators 5LS00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00987670
Connecting Rod Bearings - Install
SMCS - 1219-012
Installation Procedure
Table 1
Tool Part Number Part Description Qty
A - Plastigage -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when the clearance checks are made. Put clean
engine oil on the connecting rod bearings for final assembly.
1. Install the upper half of the connecting rod bearing in the connecting rod.
2. Install the lower half of the connecting rod bearing in the connecting rod.
Note: Align the tabs on the back of the connecting rod bearings with the tab grooves in the
connecting rod.
1/3(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00487493
3. In order to check the connecting rod bearing clearance, put Tool (A) on the connecting rod
bearing, as shown.
4. Put clean engine oil (SAE 30) on the connecting rod bolts.
NOTICE
When the connecting rod caps are installed, ensure that the
identification marks are aligned.
Illustration 2 g00487412
Note: Do not turn the crankshaft when Tool (A) is positioned.
5. Ensure that connecting rod (3) is in position on the crankshaft. Install connecting rod cap (2)
and connecting rod nuts (1) on connecting rod (3) .
2/3(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 3 g00287852
6. Tighten the connecting rod nuts to a torque of 40 ± 4 N·m (30 ± 3 lb ft). Mark the position
of the nuts. Tighten each nut for an additional 90 degrees (1/4 turn).
7. Remove the connecting rod cap. Measure Tool (A) on the bearing surface before Tool (A) is
removed. The clearance between the connecting rod bearing and a new crankshaft should be
0.076 to 0.168 mm (.0025 to .0066 inch). The clearance between the connecting rod bearing
and a used crankshaft should be 0.25 mm (0.01 inch).
8. Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3). Repeat
Step 6 in order to tighten the nuts.
9. Repeat Steps 1 through 8 for the remaining connecting rod bearings.
End By:
a. Install the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate -
Remove and Install".
b. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 28 20:06:18 UTC+0800 2020
3/3(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B L EXCAVATOR 5LS
Configuration: 330B & 330B L Excavators 5LS00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00990466
Crankshaft Main Bearings - Remove
SMCS - 1203-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1
Start By:
A. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
B. Remove the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 1 g00479056
1. Remove No. 1, 3, 5 and 7 main bearing caps (3). Remove the lower halves of the main
bearings from the main bearing caps.
Note: If the crankshaft is turned in the wrong direction, the tab on the bearing will be
pushed between the crankshaft and the bearing area in the cylinder block. This can result in
damage to the cylinder block and/or the crankshaft.
2. Install Tool (A) in the oil hole in the crankshaft journal. Turn the crankshaft in order to
remove the upper halves of main bearings (1) .
3. Remove crankshaft thrust plates (2) from the crankshaft.
4. Install No. 1, 3, 5, and 7 main bearing caps (3). Refer to Disassembly and Assembly,
"Crankshaft Main Bearings - Install".
5. Remove the remaining main bearing caps (No. 2, 4 and 6) (3). Remove the lower halves of
the main bearings from the main bearing caps.
Note: If the crankshaft is turned in the wrong direction, the tab on the bearing will be
pushed between the crankshaft and the bearing area in the cylinder block. This can result in
damage to the cylinder block and/or the crankshaft.
6. Install Tool (A) in the hole in the crankshaft journal. Turn the crankshaft in order to remove
the upper halves of main bearings (1) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 28 20:07:14 UTC+0800 2020
2/2(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B L EXCAVATOR 5LS
Configuration: 330B & 330B L Excavators 5LS00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i03706647
Crankshaft Main Bearings - Install
SMCS - 1203-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1
B - Plastigage -
C 8T-5096 Dial Indicator Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Install the main bearings dry when the clearance checks are made. Put clean engine oil on
the main bearings for final assembly.
Note: Ensure that the upper halves and the lower halves of the main bearings are installed so that
the bearing tabs fit into the notch in the cylinder block and in the main bearing caps.
1/4(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g00479169
Illustration 2 g00479171
1. Use Tooling (A) and install the new upper halves of main bearings (1) in the cylinder block.
Install new lower halves of main bearings (1) in main bearing caps (2) .
Note: When the bearing clearance is checked and the engine is in an upright position or on
the engine's side, the crankshaft must be supported against the upper halves of the main
bearings. This is done in order to get a correct measurement with Tooling (B) . If the
crankshaft is not supported, the weight of the crankshaft will cause an incorrect reading. If
the engine is not in an upright position or on the engine's side, it is not necessary to support
the crankshaft. Do not rotate the crankshaft when Tooling (B) is positioned.
Note: Refer to Guideline For Reusable Parts, SEBV0544, "Engine Bearings and
Crankshafts" for complete details concerning the measurement of bearing clearances.
2. Check the main bearing clearance with Tooling (B) , as follows:
a. Put a piece of Tooling (B) on the crankshaft journals, as shown.
Note: Make sure that the part number on the main bearing cap is facing toward the
front of the engine. Also, make sure that the number on the main bearing cap matches
the number on the cylinder block on the left side of each main bearing cap.
2/4(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. b. Put main bearing caps (2) in position in the engine. Put 4C-5593 Anti-Seize
Compound on the bolt threads and the face of the washers. Install the bolts and
tighten the bolts to torque of 40 ± 4 N·m (30 ± 3 lb ft).
c. Put a mark on each bolt and main bearing cap. Tighten the bolts for an additional 90
degrees (1/4 turn).
d. Remove the main bearing caps and measure Tooling (B) in order to find the bearing
clearance. The main bearing clearance for new bearings must be 0.076 to 0.165 mm
(0.0030 to 0.0065 inch). The maximum permissible clearance with used bearings is
0.25 mm (0.010 inch).
Illustration 3 g00479203
3. Put clean oil on thrust plate (4) and install a new thrust plate for the rear main bearing.
Install the new thrust plate so that the mark that is identified as the "BLOCK SIDE" faces
toward the cylinder block and toward the tabs on the thrust plates in the machined area on
the cylinder block. Tabs (3) on thrust plate (4) will not allow the thrust plate to be installed
backward.
Illustration 4 g00479205
3/4(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. 4. Install main bearing caps (2) . Use the same procedure that is described in Step 2.b and Step
2.c.
5. Remove the remainder of the main bearing caps. Perform Steps 1, 2 and 4 again.
Illustration 5 g00479212
6. Use Tooling (C) in order to check the crankshaft end play. The end play is controlled by the
thrust plates on the rear main bearing. End play with new bearings must be 0.122 to 0.579
mm (0.0048 to 0.0228 inch).
End By:
a. Install the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate -
remove and install".
b. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 28 20:08:09 UTC+0800 2020
4/4(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B L EXCAVATOR 5LS
Configuration: 330B & 330B L Excavators 5LS00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01112752
Crankshaft - Remove
SMCS - 1202-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B
8B-7551 Bearing Puller 1
8B-7549 Puller Leg 2
3H-0465 Push-Puller Plate 4
1B-4207 Full Nut 2
8B-7560 Step Plate 1
1P-0820 Hydraulic Puller 1
9U-6600 Hand Hydraulic Pump 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Front Housing - Remove".
B. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
C. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
D. Remove the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate -
Remove and Install".
1/4(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00503163
1. Turn the crankshaft until timing mark "C" on crankshaft gear (1) is aligned with timing
mark "C" on camshaft gear (2) .
Illustration 2 g00503180
2. Remove connecting rod nuts (4) and connecting rod caps (3) from the connecting rods.
NOTICE
2/4(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Damage may occur to the fuel injection nozzle or the piston if the
piston and connecting rod are pushed too far down in the cylinder
liners.
Note: The piston will be difficult to push down into the cylinder when the inlet valves and
exhaust valves are closed.
3. Push down on the pistons that are not at the top center position in order to clear the
crankshaft.
4. Remove main bearing cap bolts (5) and main bearing caps (6) from the cylinder block.
Illustration 3 g00503320
5. Remove thrust plates (7) from the rear main bearing.
Illustration 4 g00503353
6. Install Tool (A) and a suitable lifting device on crankshaft (8), as shown. Lift the crankshaft
straight up from the cylinder block. The weight of the 3304B crankshaft is 65 kg (143 lb).
The weight of the 3306B crankshaft is 95 Kg (210 lb).
3/4(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 5 g00503384
7. Use Tool (B) in order to remove the crankshaft gear and the oil seal wear sleeve from the
crankshaft.
Note: Put identification marks on the bearings and on the bearing caps prior to removal.
8. Remove the main bearings from the main bearing caps and from the cylinder block.
Remove the connecting rod bearings from the connecting rods and from the connecting rod
caps.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 28 20:09:05 UTC+0800 2020
4/4(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B L EXCAVATOR 5LS
Configuration: 330B & 330B L Excavators 5LS00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i03706543
Crankshaft - Install
SMCS - 1202-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B - Plastigage -
C 8T-5096 Dial Indicator Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Install the main bearings dry when the clearance checks are made. Put clean engine oil on
the main bearings for final assembly.
Note: Ensure that the upper halves and the lower halves of the main bearings are installed so that
the bearing tabs fit into the bearing tab grooves in the cylinder block and in the main bearing caps.
1/6(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 1 g00503582
1. If the bearings were removed from the engine, clean the bearing surfaces in the cylinder
block and the main bearing caps. Install the upper halves of connecting rod bearings (1) and
main bearings (2) .
Illustration 2 g00503642
Hot oil and hot components can cause personal injury. Do not allow hot
oil or hot components to contact the skin.
2. Heat crankshaft gear (3) to a maximum temperature of 315 °C (600 °F). Install crankshaft
gear (3) on the crankshaft.
2/6(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 3 g00503668
3. Install Tooling (A) on the ends of the crankshaft and use a hoist to lower the crankshaft into
position above the cylinder block. Align the connecting rods with the crankshaft. Align the
"C" mark on crankshaft gear (3) with the "C" mark on camshaft gear (4) . Lower the
crankshaft into position in the cylinder block.
Note: When the bearing clearance is checked and the engine is in an upright position or on
the engine's side, the crankshaft must be supported against the upper halves of the main
bearings. This is done in order to get a correct measurement with Tooling (B) . If the
crankshaft is not supported, the weight of the crankshaft will cause an incorrect reading. If
the engine is not in an upright position or on the engine's side, it is not necessary to support
the crankshaft. Do not rotate the crankshaft when Tooling (B) is positioned.
Note: Refer to Guideline For Reusable Parts, SEBV0544, "Engine Bearings and
Crankshafts" for complete details concerning the measurement of bearing clearances.
Illustration 4 g00503884
4. Check the main bearing clearance with Tooling (B) , as follows:
a. Put a piece of Tooling (B) on the crankshaft journal, as shown.
Note: Make sure that the part number on the main bearing cap is facing toward the
front of the engine. Also, make sure that the number on the main bearing cap matches
the number on the cylinder block on the left side of each main bearing cap.
3/6(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. b. Put the main bearing caps in position in the engine. Put 4C-5593 Anti-Seize
Compound on the bolt threads and the face of the washers. Install the bolts and
tighten the bolts to a torque of 40 ± 4 N·m (30 ± 3 lb ft).
c. Put a mark on each bolt and main bearing cap. Tighten the bolts for an additional 90
degrees (1/4 turn).
d. Remove the main bearing caps and measure Tooling (B) in order to find the bearing
clearance. The main bearing clearance for new bearings must be 0.076 to 0.165 mm
(0.0030 to 0.0065 inch). The maximum permissible clearance with used bearings is
0.25 mm (0.010 inch).
Illustration 5 g00503913
5. Put clean engine oil on thrust plate (7) for the rear main bearing. Install the new thrust plate
so that the mark that is identified as the "BLOCK SIDE" faces toward the cylinder block
and toward the tabs on the thrust plates in the machined area on the cylinder block. Tabs (6)
will not allow thrust plate (7) to be installed backward.
Illustration 6 g00504005
6. Install the remaining main bearing caps. Use the same procedure that is described in Step
4.b and Step 4.c.
4/6(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 7 g00504013
7. Check the crankshaft end play with Tooling (C) . The end play is controlled by the thrust
plates on the rear main bearing. End play with new thrust plates must be 0.122 to 0.579 mm
(0.0048 to 0.0228 inch).
Illustration 8 g00504198
8. Pull the connecting rod into position against the crankshaft.
Note: Install the connecting rod bearings dry when the clearance checks are made. Put clean
engine oil on the connecting rod bearings for final assembly.
9. Install the lower half of rod bearing (8) in the connecting rod cap. Align the tab in the
connecting rod bearing with the tab in the connecting rod cap.
10. In order to check the connecting rod bearing clearance, put Tooling (B) in position on the
crankshaft, as shown.
NOTICE
5/6(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. When the connecting rod caps are installed, ensure that the
identification marks are aligned.
Illustration 9 g00504276
11. Make sure that the connecting rod is in position on the crankshaft. Install connecting rod cap
(9) and the connecting rod nuts.
12. Tighten the connecting rod nuts to a torque of 40 ± 4 N·m (30 ± 3 lb ft). Mark the position
of the connecting rod nuts. Tighten each nut for an additional 90 degrees (1/4 turn).
13. Remove connecting rod cap (9) and measure the thickness of the Plastigage on the
crankshaft. The connecting rod clearance must be 0.076 to 0.168 mm (0.0030 to 0.0066) for
new bearings. The maximum clearance for used connecting rod bearings should be 0.25 mm
(0.010 inch).
14. Install connecting rod cap (9) and tighten the nuts. Refer to Step 12 for the tightening
procedure.
15. Repeat Steps 8 through 14 for the remaining connecting rod bearings.
End By:
a. Install the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate -
Remove and Install".
b. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
c. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
d. Install the front housing. Refer to Disassembly and Assembly, "Front Housing - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 28 20:10:01 UTC+0800 2020
6/6(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B L EXCAVATOR 5LS
Configuration: 330B & 330B L Excavators 5LS00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i05977048
Bearing Clearance - Check
SMCS - 1203-535; 1219-535
Measurement Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
198-9142
Plastic Gauge (Green)
0.025 to 0.076 mm
(0.001 to 0.003 inch)
1
198-9143
Plastic Gauge (Red)
0.051 to 0.152 mm
(0.002 to 0.006 inch)
1
198-9144
Plastic Gauge (Blue)
0.102 to 0.229 mm
(0.004 to 0.009 inch)
1
198-9145
Plastic Gauge (Yellow)
0.230 to 0.510 mm
(0.009 to 0.020 inch)
1
Note: Plastic gauge may not be necessary when the engine is in the chassis.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Note: Cat does not recommend the checking of the actual bearing clearances particularly on small
engines. This is because of the possibility of obtaining inaccurate results and the possibility of
damaging the bearing or the journal surfaces. Each Cat engine bearing is quality checked for
specific wall thickness.
Note: The measurements should be within specifications and the correct bearings should be used.
If the crankshaft journals and the bores for the block and the rods were measured during
disassembly, no further checks are necessary. However, if the technician still wants to measure the
bearing clearances, Tooling (A) is an acceptable method. Tooling (A) is less accurate on journals
with small diameters if clearances are less than 0.10 mm (0.004 inch).
NOTICE
Lead wire, shim stock or a dial bore gauge can damage the bearing
surfaces.
The technician must be very careful to use Tooling (A) correctly. The following points must be
remembered:
• Ensure that the backs of the bearings and the bores are clean and dry.
• Ensure that the bearing locking tabs are properly seated in the tab grooves.
• The crankshaft must be free of oil at the contact points of Tooling (A).
1. Put a piece of Tooling (A) on the crown of the bearing that is in the cap.
Note: Do not allow Tooling (A) to extend over the edge of the bearing.
2. Use the correct torque-turn specifications in order to install the bearing cap. Do not use an
impact wrench. Be careful not to dislodge the bearing when the cap is installed.
Note: Do not turn the crankshaft when Tooling (A) is installed.
3. Carefully remove the cap, but do not remove Tooling (A). Measure the width of Tooling
(A) while Tooling (A) is in the bearing cap or on the crankshaft journal. Refer to Illustration
1.
2/3(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 1 g01152855
Typical Example
4. Remove all of Tooling (A) before you install the bearing cap.
Note: When Tooling (A) is used, the readings can sometimes be unclear. For example, all
parts of Tooling (A) are not the same width. Measure the major width in order to ensure that
the parts are within the specification range. Refer to Specifications Manual, "Connecting
Rod Bearing Journal" and Specifications Manual, "Main Bearing Journal" for the correct
clearances.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 28 20:10:57 UTC+0800 2020
3/3(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B L EXCAVATOR 5LS
Configuration: 330B & 330B L Excavators 5LS00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i02107209
Coolant Temperature Sensor - Remove and Install
SMCS - 1906-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2(W)
w
2020/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...