This document provides instructions to remove and disassemble components of the rocker shaft and pushrods on a 325B L excavator powered by a 3116 engine. The summary is as follows:
1) Remove the valve mechanism cover, rocker shaft assembly bolts, and rocker shaft assembly to access the pushrods and rocker arms.
2) Remove the pushrods and individual rocker arms and inspect the rocker shaft assembly and rocker arm components.
3) Reassemble the rocker shaft by installing new bearings if needed, lubricating, and reinstalling the rocker arms and support bracket.
4) Install the rocker shaft assembly and pushrods
Caterpillar cat 325 b l excavator (prefix 5bs) service repair manual (5bs0000...fjjskekdmme
This document provides instructions for removing and installing the rocker shaft and pushrods on a 325B L excavator engine. It describes removing the valve mechanism cover, loosening the rocker arm adjustment screws, removing bolts and the rocker shaft assembly from the cylinder head. It also details installing the rocker shaft by positioning it in the engine and lining up the pushrods with the rocker arms, installing bolts, adjusting valve lash, and reinstalling the valve mechanism cover.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...fjsjjekdkme
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 b excavator (prefix 6dn) service repair manual (6dn00001 ...fjsjjekdkme
This service repair manual provides instructions for removing and installing inlet manifolds, valves, and valve guides on Caterpillar 325B and 325B LN excavator engines. The document outlines the required tools and safety procedures, and provides step-by-step instructions with illustrations for each repair procedure. Technicians are advised to keep parts clean, contain fluids properly, and refer to other documents for guidance on reusable components.
Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr0000...fjskefkemms
The document provides instructions for servicing components of a 330B L excavator including:
1. Installing a compression brake on the engine and connecting wires.
2. Removing and assembling the rocker shaft and pushrods, including disassembling the rocker shaft into individual components.
3. Removing the cylinder head from the engine which involves removing manifold, pushrods, and bolts holding the head in place. Proper lifting equipment is needed due to the head's weight.
Caterpillar cat 416 d backhoe loader (prefix cxp) service repair manual (cxp0...ujjfjkskekmme
This document provides instructions for removing, disassembling, assembling, and installing solenoid valves for the transmission of a Caterpillar 416D backhoe loader. The instructions cover removing floorplates, disconnecting wiring, and removing solenoid valves. Disassembly involves removing nuts, covers, seals, and solenoids. Assembly requires cleaning parts and replacing seals before reinstalling components. Safety notices warn of potential injuries from hydraulic pressure and recommend proper fluid handling and disposal.
Caterpillar cat 416 b backhoe loader (prefix 8zk) service repair manual (8zk0...fujsjefksekmm
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It describes using special tools to remove the pulley by loosening bolts and removing a locking plate. When installing the new pulley, the instructions specify tightening the bolts to the specified torque and installing a new locking plate. The summary is intended only to convey the main steps and should not be used as a replacement for the full instructions.
Caterpillar cat 330 b excavator (prefix 4rs) service repair manual (4rs00001 ...hfjsekekmmd
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe procedures for removing and installing the cylinder head, rocker shaft and pushrods. Specific steps include removing bolts and lifting the cylinder head from the engine block using proper lifting devices. The rocker shaft is disassembled by removing retaining rings, springs and rocker arms. It is then reassembled by installing these parts in the proper order and orientation.
Caterpillar cat 299 d xhp compact track loader (prefix jst) service repair ma...ujfdjjskkmsme
The document provides instructions for removing and installing various engine components on a Caterpillar 299D XHP compact track loader, including:
- Water pump removal and installation procedures involving removing guards, belts, bolts, and gaskets.
- Water temperature regulator removal involving disconnecting hoses and removing bolts, cover, and gasket.
- Flywheel removal involving removing bolts, pump coupling, and lifting the flywheel assembly off.
- Crankshaft rear seal removal by drilling holes in the seal and using a slide hammer, and installation using a driver tool.
- Crankshaft rear seal carrier removal by removing bolts and the bearing case cover, and installation by
Caterpillar cat 325 b l excavator (prefix 5bs) service repair manual (5bs0000...fjjskekdmme
This document provides instructions for removing and installing the rocker shaft and pushrods on a 325B L excavator engine. It describes removing the valve mechanism cover, loosening the rocker arm adjustment screws, removing bolts and the rocker shaft assembly from the cylinder head. It also details installing the rocker shaft by positioning it in the engine and lining up the pushrods with the rocker arms, installing bolts, adjusting valve lash, and reinstalling the valve mechanism cover.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...fjsjjekdkme
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 b excavator (prefix 6dn) service repair manual (6dn00001 ...fjsjjekdkme
This service repair manual provides instructions for removing and installing inlet manifolds, valves, and valve guides on Caterpillar 325B and 325B LN excavator engines. The document outlines the required tools and safety procedures, and provides step-by-step instructions with illustrations for each repair procedure. Technicians are advised to keep parts clean, contain fluids properly, and refer to other documents for guidance on reusable components.
Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr0000...fjskefkemms
The document provides instructions for servicing components of a 330B L excavator including:
1. Installing a compression brake on the engine and connecting wires.
2. Removing and assembling the rocker shaft and pushrods, including disassembling the rocker shaft into individual components.
3. Removing the cylinder head from the engine which involves removing manifold, pushrods, and bolts holding the head in place. Proper lifting equipment is needed due to the head's weight.
Caterpillar cat 416 d backhoe loader (prefix cxp) service repair manual (cxp0...ujjfjkskekmme
This document provides instructions for removing, disassembling, assembling, and installing solenoid valves for the transmission of a Caterpillar 416D backhoe loader. The instructions cover removing floorplates, disconnecting wiring, and removing solenoid valves. Disassembly involves removing nuts, covers, seals, and solenoids. Assembly requires cleaning parts and replacing seals before reinstalling components. Safety notices warn of potential injuries from hydraulic pressure and recommend proper fluid handling and disposal.
Caterpillar cat 416 b backhoe loader (prefix 8zk) service repair manual (8zk0...fujsjefksekmm
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It describes using special tools to remove the pulley by loosening bolts and removing a locking plate. When installing the new pulley, the instructions specify tightening the bolts to the specified torque and installing a new locking plate. The summary is intended only to convey the main steps and should not be used as a replacement for the full instructions.
Caterpillar cat 330 b excavator (prefix 4rs) service repair manual (4rs00001 ...hfjsekekmmd
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe procedures for removing and installing the cylinder head, rocker shaft and pushrods. Specific steps include removing bolts and lifting the cylinder head from the engine block using proper lifting devices. The rocker shaft is disassembled by removing retaining rings, springs and rocker arms. It is then reassembled by installing these parts in the proper order and orientation.
Caterpillar cat 299 d xhp compact track loader (prefix jst) service repair ma...ujfdjjskkmsme
The document provides instructions for removing and installing various engine components on a Caterpillar 299D XHP compact track loader, including:
- Water pump removal and installation procedures involving removing guards, belts, bolts, and gaskets.
- Water temperature regulator removal involving disconnecting hoses and removing bolts, cover, and gasket.
- Flywheel removal involving removing bolts, pump coupling, and lifting the flywheel assembly off.
- Crankshaft rear seal removal by drilling holes in the seal and using a slide hammer, and installation using a driver tool.
- Crankshaft rear seal carrier removal by removing bolts and the bearing case cover, and installation by
Caterpillar cat 325 b ln excavator (prefix 5bs) service repair manual (5bs000...fjjskekdmme
This document provides instructions for removing and installing a cylinder head on a 325B L & 325B LN Excavator powered by a 3116 engine. The removal procedure involves detaching various components from the engine and lifting the cylinder head off using a lifting device. The installation procedure specifies cleaning the mating surfaces and installing a new cylinder head gasket before lowering the cylinder head back onto the cylinder block.
Caterpillar cat 325 b ln excavator (prefix 8fn) service repair manual (8fn000...fjsjjekdkme
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...f98soeodidkdk
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar Cat 325B and 325B LN Excavator (Prefix 8FN) Service Repair Manual...yan77xunhao
This document provides instructions for removing and servicing components of the rocker shaft and cylinder head on a 325B and 325B LN Excavator powered by a 3116 engine. The procedures include removing the rocker shaft assembly, disassembling the rocker shaft, inspecting components, assembling the rocker shaft, installing the rocker shaft and pushrods, and removing the cylinder head. Detailed steps are outlined along with required tools and safety notices to keep parts clean and contain fluids.
Caterpillar cat 325 b ln excavator (prefix 8fn) service repair manual (8fn000...f98soeodidkdk
This document provides instructions for removing and servicing components of the rocker shaft and cylinder head on a 325B and 325B LN Excavator powered by a 3116 engine. The procedures include removing the rocker shaft assembly, disassembling the rocker shaft, inspecting components, assembling the rocker shaft, installing the rocker shaft and pushrods, and removing the cylinder head. Detailed steps are provided along with illustrations to guide the technician through the process while maintaining cleanliness and proper torque specifications.
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
This document provides instructions for removing and servicing components of the rocker shaft and cylinder head on a 325B and 325B LN Excavator powered by a 3116 engine. The procedures include removing the rocker shaft assembly, disassembling the rocker shaft, inspecting components, assembling the rocker shaft, installing the rocker shaft and pushrods, and removing the cylinder head. Detailed steps are outlined along with required tools and safety notices to keep parts clean and contain fluids.
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before installing the new gasket and bolting the cylinder head back into place. Technicians are advised to keep parts clean and contain fluids properly during the work.
This document contains a table of contents and specifications for parts related to the engine, fuel, exhaust, cooling, air conditioning, and intake systems of a Massey Ferguson TH.8043 130 S3A telescopic handler. It includes over 50 numbered items with descriptions and part numbers for components such as the radiator, muffler, hoses, clamps, sensors, and other engine accessories. The parts are grouped into sections for each vehicle system and subsystems.
The document is a parts catalog for a Massey Ferguson TH.7030 ST4 telescopic handler. It lists parts for the engine, fuel, and exhaust systems across multiple pages, with each page covering a different subsystem. The parts are organized in a table with the part number, quantity, description, and any additional comments. The parts listed include components for the cooling system, air intake, exhaust system, SCR system housing, and other engine systems.
This document provides parts information for a Massey Ferguson 89410/89410(L) telescopic handler, including:
- A list of 43 parts that make up the main frame, with part numbers, quantities, descriptions, and comments.
- A list of 9 parts that make up the counterweights and attachments on the frame.
- A list of 20 parts that make up the fuel system including the fuel tank and attachments.
- A list of 27 parts that make up the engine cover.
- A list of 21 parts that make up the engine support.
- A list of 30 parts that make up the cab.
- A list of 31 parts that make
Massey ferguson mf 9305 telescopic handler europe parts catalogue manualfjjskedmme
This document provides a table of contents and component listings for the engine, fuel, and exhaust systems of a Massey Ferguson MF 9305 telescopic handler. It includes over 50 pages detailing over 1000 individual components that make up these various mechanical systems of the vehicle. The pages provide diagrams and lists of parts, their numbers, quantities, and brief descriptions.
Massey ferguson mf 9205 telescopic handler parts catalogue manualfjjskedmme
This document provides a list of parts for a Massey Ferguson MF 9205 telescopic handler, including the main frame, counterweight, engine support and cover, cab installation, cab windows and door, and tractor cab windscreen wiper. It includes the part numbers, quantities, descriptions, and comments for 76 total parts.
This document provides parts information for a Massey Ferguson 8947 telescopic handler, including:
- A list of 40 parts for the main frame with part numbers, quantities, descriptions, and comments.
- A list of 9 parts for the counterweights with similar information.
- A list of 20 parts for the fuel system including the fuel tank, lines, caps, and attachments.
- A list of 48 parts for the engine cover and attachments up to a certain serial number.
- A list of 28 parts for the engine cover and attachments from another serial number range.
- A list of 18 parts for the engine support system.
- A list of 30 parts for the
Massey ferguson mf 8947 telescopic handler (3636 11187-999) parts catalogue...fjjskedmme
This document provides a table of contents and specifications for engine, fuel, exhaust and other systems for a Massey Ferguson MF 8947 telescopic handler. It includes over 30 pages detailing individual parts, part numbers, quantities and references for the engine, drivetrain, hydraulic, electrical and other systems. The level of detail provided in the document allows for identification and ordering of replacement parts for maintenance and repair of the telescopic handler.
Massey ferguson mf 8947 t3 (a8 hh13000 99999) mf 8947 cd t3 (a8hj13000-99999...fjjskedmme
This document provides a table of contents and sections for repair and maintenance of Massey Ferguson MF 8947 T3 and MF 8947 CD T3 telescopic handlers. The sections include the engine and fuel systems, drive train, hydraulics, electrical systems, chassis, and attachments. Each section lists relevant part numbers, quantities, and descriptions.
This document provides part numbers and descriptions for engine components of Massey Ferguson MF 8937 and MF 8939 telescopic handlers, including:
- Cylinder block parts for engines without and with turbocharger.
- Crankshaft, piston, and connecting rod components for non-turbocharged and turbocharged engines.
- The document lists part numbers, quantities, descriptions and other identifying information for each component.
Massey ferguson mf 8937 8939 telescopic handlers parts catalogue manualfjjskedmme
This document provides parts information for Massey Ferguson MF 8937 and MF 8939 telescopic handlers, including cylinder block, crankshaft, pistons, connecting rods, and cylinder head parts. It lists the part numbers, quantities, descriptions and comments such as replacement requirements for various engine components up to specific serial numbers for engines with and without turbochargers.
This document contains parts lists and diagrams for components of Massey Ferguson MF 8925/8926 telescopic handlers, including the main frame, counterweights, fuel system, engine cover, engine support, and cab. It provides detailed part numbers, quantities, descriptions and comments for each item listed. Footnotes indicate some seals and components should be ordered by the meter or are not serviced.
Massey ferguson ideal class 7 combine parts catalogue manualfjjskedmme
This document provides part numbers and descriptions for components related to the engine, starter, alternator, and air conditioning compressor for a Massey Ferguson Ideal Class 7 combine. It includes items such as engine mounts, belts, hoses, filters, drain valves, shields, bolts, and the engine, starter, alternator and compressor themselves. Technical specifications are provided for some parts.
Massey ferguson 9895 combine (effective sn hsc8101) parts catalogue manualfjjskedmme
This document provides a list of parts and their descriptions for a Massey Ferguson 9895 combine. It includes 26 items related to the combine's engine air intake and exhaust systems. The items listed are the air intake tube, turbocharger, exhaust manifold, and various hoses and clamps.
Massey ferguson 9795 rotary combine parts catalogue manualfjjskedmme
The document provides a parts list and technical specifications for the engine and cylinder block of a Massey Ferguson 9795 rotary combine. It includes over 50 individual parts for the engine and cylinder block, including the cylinder block, camshaft, liners, plugs, gaskets, bolts, and other components. The parts list includes the part numbers, quantities, descriptions, and any relevant technical specifications or comments for each part.
More Related Content
Similar to Caterpillar cat 325 b l excavator (prefix 5bs) service repair manual (5bs00001 and up)
Caterpillar cat 325 b ln excavator (prefix 5bs) service repair manual (5bs000...fjjskekdmme
This document provides instructions for removing and installing a cylinder head on a 325B L & 325B LN Excavator powered by a 3116 engine. The removal procedure involves detaching various components from the engine and lifting the cylinder head off using a lifting device. The installation procedure specifies cleaning the mating surfaces and installing a new cylinder head gasket before lowering the cylinder head back onto the cylinder block.
Caterpillar cat 325 b ln excavator (prefix 8fn) service repair manual (8fn000...fjsjjekdkme
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...f98soeodidkdk
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar Cat 325B and 325B LN Excavator (Prefix 8FN) Service Repair Manual...yan77xunhao
This document provides instructions for removing and servicing components of the rocker shaft and cylinder head on a 325B and 325B LN Excavator powered by a 3116 engine. The procedures include removing the rocker shaft assembly, disassembling the rocker shaft, inspecting components, assembling the rocker shaft, installing the rocker shaft and pushrods, and removing the cylinder head. Detailed steps are outlined along with required tools and safety notices to keep parts clean and contain fluids.
Caterpillar cat 325 b ln excavator (prefix 8fn) service repair manual (8fn000...f98soeodidkdk
This document provides instructions for removing and servicing components of the rocker shaft and cylinder head on a 325B and 325B LN Excavator powered by a 3116 engine. The procedures include removing the rocker shaft assembly, disassembling the rocker shaft, inspecting components, assembling the rocker shaft, installing the rocker shaft and pushrods, and removing the cylinder head. Detailed steps are provided along with illustrations to guide the technician through the process while maintaining cleanliness and proper torque specifications.
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
This document provides instructions for removing and servicing components of the rocker shaft and cylinder head on a 325B and 325B LN Excavator powered by a 3116 engine. The procedures include removing the rocker shaft assembly, disassembling the rocker shaft, inspecting components, assembling the rocker shaft, installing the rocker shaft and pushrods, and removing the cylinder head. Detailed steps are outlined along with required tools and safety notices to keep parts clean and contain fluids.
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before installing the new gasket and bolting the cylinder head back into place. Technicians are advised to keep parts clean and contain fluids properly during the work.
Similar to Caterpillar cat 325 b l excavator (prefix 5bs) service repair manual (5bs00001 and up) (8)
This document contains a table of contents and specifications for parts related to the engine, fuel, exhaust, cooling, air conditioning, and intake systems of a Massey Ferguson TH.8043 130 S3A telescopic handler. It includes over 50 numbered items with descriptions and part numbers for components such as the radiator, muffler, hoses, clamps, sensors, and other engine accessories. The parts are grouped into sections for each vehicle system and subsystems.
The document is a parts catalog for a Massey Ferguson TH.7030 ST4 telescopic handler. It lists parts for the engine, fuel, and exhaust systems across multiple pages, with each page covering a different subsystem. The parts are organized in a table with the part number, quantity, description, and any additional comments. The parts listed include components for the cooling system, air intake, exhaust system, SCR system housing, and other engine systems.
This document provides parts information for a Massey Ferguson 89410/89410(L) telescopic handler, including:
- A list of 43 parts that make up the main frame, with part numbers, quantities, descriptions, and comments.
- A list of 9 parts that make up the counterweights and attachments on the frame.
- A list of 20 parts that make up the fuel system including the fuel tank and attachments.
- A list of 27 parts that make up the engine cover.
- A list of 21 parts that make up the engine support.
- A list of 30 parts that make up the cab.
- A list of 31 parts that make
Massey ferguson mf 9305 telescopic handler europe parts catalogue manualfjjskedmme
This document provides a table of contents and component listings for the engine, fuel, and exhaust systems of a Massey Ferguson MF 9305 telescopic handler. It includes over 50 pages detailing over 1000 individual components that make up these various mechanical systems of the vehicle. The pages provide diagrams and lists of parts, their numbers, quantities, and brief descriptions.
Massey ferguson mf 9205 telescopic handler parts catalogue manualfjjskedmme
This document provides a list of parts for a Massey Ferguson MF 9205 telescopic handler, including the main frame, counterweight, engine support and cover, cab installation, cab windows and door, and tractor cab windscreen wiper. It includes the part numbers, quantities, descriptions, and comments for 76 total parts.
This document provides parts information for a Massey Ferguson 8947 telescopic handler, including:
- A list of 40 parts for the main frame with part numbers, quantities, descriptions, and comments.
- A list of 9 parts for the counterweights with similar information.
- A list of 20 parts for the fuel system including the fuel tank, lines, caps, and attachments.
- A list of 48 parts for the engine cover and attachments up to a certain serial number.
- A list of 28 parts for the engine cover and attachments from another serial number range.
- A list of 18 parts for the engine support system.
- A list of 30 parts for the
Massey ferguson mf 8947 telescopic handler (3636 11187-999) parts catalogue...fjjskedmme
This document provides a table of contents and specifications for engine, fuel, exhaust and other systems for a Massey Ferguson MF 8947 telescopic handler. It includes over 30 pages detailing individual parts, part numbers, quantities and references for the engine, drivetrain, hydraulic, electrical and other systems. The level of detail provided in the document allows for identification and ordering of replacement parts for maintenance and repair of the telescopic handler.
Massey ferguson mf 8947 t3 (a8 hh13000 99999) mf 8947 cd t3 (a8hj13000-99999...fjjskedmme
This document provides a table of contents and sections for repair and maintenance of Massey Ferguson MF 8947 T3 and MF 8947 CD T3 telescopic handlers. The sections include the engine and fuel systems, drive train, hydraulics, electrical systems, chassis, and attachments. Each section lists relevant part numbers, quantities, and descriptions.
This document provides part numbers and descriptions for engine components of Massey Ferguson MF 8937 and MF 8939 telescopic handlers, including:
- Cylinder block parts for engines without and with turbocharger.
- Crankshaft, piston, and connecting rod components for non-turbocharged and turbocharged engines.
- The document lists part numbers, quantities, descriptions and other identifying information for each component.
Massey ferguson mf 8937 8939 telescopic handlers parts catalogue manualfjjskedmme
This document provides parts information for Massey Ferguson MF 8937 and MF 8939 telescopic handlers, including cylinder block, crankshaft, pistons, connecting rods, and cylinder head parts. It lists the part numbers, quantities, descriptions and comments such as replacement requirements for various engine components up to specific serial numbers for engines with and without turbochargers.
This document contains parts lists and diagrams for components of Massey Ferguson MF 8925/8926 telescopic handlers, including the main frame, counterweights, fuel system, engine cover, engine support, and cab. It provides detailed part numbers, quantities, descriptions and comments for each item listed. Footnotes indicate some seals and components should be ordered by the meter or are not serviced.
Massey ferguson ideal class 7 combine parts catalogue manualfjjskedmme
This document provides part numbers and descriptions for components related to the engine, starter, alternator, and air conditioning compressor for a Massey Ferguson Ideal Class 7 combine. It includes items such as engine mounts, belts, hoses, filters, drain valves, shields, bolts, and the engine, starter, alternator and compressor themselves. Technical specifications are provided for some parts.
Massey ferguson 9895 combine (effective sn hsc8101) parts catalogue manualfjjskedmme
This document provides a list of parts and their descriptions for a Massey Ferguson 9895 combine. It includes 26 items related to the combine's engine air intake and exhaust systems. The items listed are the air intake tube, turbocharger, exhaust manifold, and various hoses and clamps.
Massey ferguson 9795 rotary combine parts catalogue manualfjjskedmme
The document provides a parts list and technical specifications for the engine and cylinder block of a Massey Ferguson 9795 rotary combine. It includes over 50 individual parts for the engine and cylinder block, including the cylinder block, camshaft, liners, plugs, gaskets, bolts, and other components. The parts list includes the part numbers, quantities, descriptions, and any relevant technical specifications or comments for each part.
Massey ferguson 9790 combine eff n america sn hm36101 eff s america sn 000 c9...fjjskedmme
This document contains listings of part numbers and descriptions for decals and labels used on a Massey Ferguson 9790 combine harvester. It includes decals for both North America and South America models, listing decals for the left side, front, right side and rear of the harvester. There are over 30 different decals described for labeling various parts, warnings and safety information.
Massey ferguson 9690 combine (eff sn hm87101) parts catalogue manualfjjskedmme
This document provides a parts list for engine and engine mounting components for a Massey Ferguson 9690 combine with a Cummins QSC 8.3 engine and prior serial number HR87101. It lists 44 items including the engine assembly, alternator, belts, hoses, brackets, rails, clamps, bolts, nuts, and washers that make up the engine and mounting system. Tightening specifications or additional details are not provided.
This document provides a table of contents and specifications for engine parts of a Massey Ferguson 9560 combine from 2012-2014, including the cylinder block, engine and mounting components, fuel lines and filters, and engine electrical systems. It lists over 100 individual parts that make up these engine systems, providing part numbers, descriptions, and other technical details for each component.
This document provides a table of contents and parts lists for a Massey Ferguson 9560 combine harvester engine and related systems. It includes over 40 pages detailing over 1000 individual part numbers for components such as the cylinder block, fuel injection system, engine mounts, sensors, wiring harnesses, filters and more. The level of detail provided allows for identification and ordering of any replacement part for the combine harvester engine.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930098
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of components of the rocker shaft, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8267, "Rocker Arms and Rocker Arm Shafts for
3114 and 3116 Engines".
1/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00629575
1. Loosen all rocker arm adjustment screws (3).
2. Remove bolts (1) from the rocker shaft assembly (2).
3. Remove rocker shaft assembly (2) from the cylinder head.
4. Repeat the procedure for each rocker shaft assembly.
5. Remove the pushrods.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:29:00 UTC+0800 2020
2/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930139
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-0083 Emery Polishing Paper 1
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of components of the rocker shaft, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8267, "Rocker Arms and Rocker Arm Shafts for
3114 and 3116 Engines".
1/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00629612
1. Remove support bracket (1) from rocker shaft assembly (4).
2. Remove valve rocker arms (2) and unit injector rocker arm (3) from rocker shaft assembly
(4).
Note: Do not force the rocker arms from the rocker shaft assembly. If necessary, use a piece
of Tooling (A) to lightly buff the surface of the shaft to aid in removal .
3. Check the adjustment screws on valve rocker arms (2) and unit injector rocker arm (3) for
damage.
4. Inspect rocker shaft assembly (4) for scratches and cracks.
Illustration 2 g00630277
5. Inspect bearing (5) on unit injector rocker arm (3). The bore in the rocker arm is
24.808 ± 0.20 mm (0.9767 ± 0.0079 inch). Refer to Specification, "Valve Rocker Arm and
Lifters". Replace the bearing, if necessary.
6. Ensure that button (6) on unit injector rocker arm (3) is not damaged. Also ensure that the
retaining ring for button (6) is in place.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:29:56 UTC+0800 2020
2/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930194
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of components of the rocker shaft, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8267, "Rocker Arms and Rocker Arm Shafts for
3114 and 3116 Engines".
1/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g00630277
1. Install button (6) and the retaining ring, if necessary.
2. Place clean engine oil on a new bearing (5) prior to installation.
3. Ensure that the oil hole in bearing (5) is aligned with the oil hole in the rocker arm. Hone
the bearing, if necessary. Refer to the Specifications Module for the correct dimensions.
Illustration 2 g00629612
4. Lubricate rocker shaft assembly (4) with clean engine oil.
5. Install valve rocker arms (2) and unit injector rocker arm (3) on rocker shaft assembly (4).
6. Install support bracket (1) on rocker shaft assembly (4).
End By:
a. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:30:52 UTC+0800 2020
2/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02736495
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 146-2597 Pushrod Holder 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of components of the rocker shaft, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8267, "Rocker Arms and Rocker Arm Shafts for
3114 and 3116 Engines".
1. Install the pushrods in the engine. The base of the pushrod should be in the seat of the
pushrod lifter.
2. Install Tooling (A).
1/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g00629575
3. Position rocker shaft assembly (2) in the engine. Line up the pushrods with the rocker arms.
4. Install bolts (1) in rocker shaft assembly (2). Tighten the bolts to a torque of 28 ± 7 N·m
(21 ± 5 lb ft).
5. Remove Tooling (A) from the pushrods.
6. Adjust the valve lash on all of the adjustment screws. Refer to Testing and Adjusting,
"Engine Valve Lash - Inspect/Adjust".
7. Repeat the procedure for the remaining rocker shaft assemblies.
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:31:48 UTC+0800 2020
2/2
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01935828
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
a. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
b. Remove the governor. Refer to Disassembly and Assembly, "Governor - Remove".
c. Remove the fuel control linkage. Refer to Disassembly and Assembly, "Fuel Injection
Control Linkage - Remove".
d. Remove the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
e. Remove the water temperature regulator housing. Refer to Disassembly and Assembly,
"Water Temperature Regulator Housing - Remove and Install".
f. Remove the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold -
Remove".
g. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: For information on the reusability of the cylinder head, refer to Guideline For Reusable
Parts And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114,
3116, and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 1 g01007597
Typical example
1. Attach a suitable lifting device to the cylinder head.
2/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g00654709
2. Remove bolts (1) and (2) that hold the cylinder head to the cylinder block. Carefully remove
the cylinder head from the cylinder block. The cylinder head for the 3116 engine weighs
approximately 85 kg (187 lb).
Illustration 3 g00611342
3. Remove cylinder head gasket (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:32:44 UTC+0800 2020
3/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i04147334
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4876 Lubricant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the cylinder head, refer to Guideline For Reusable
Parts And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114,
3116, and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
1. Thoroughly clean the mating surfaces of the cylinder head and the cylinder block.
1/5
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00611342
Typical example
2. Install a new cylinder head gasket (3) .
Note: For information on the cylinder head gasket for 3116 engines, refer to Special
Instruction, SEHS9395, "3116 Cylinder Head Gasket Usage".
Illustration 2 g01007597
Typical example
Note: To avoid damage to the cylinder head gasket, use guide bolts of an appropriate size to
install the cylinder head.
3. Attach a suitable lifting device to the cylinder head. Position the cylinder head assembly
onto the dowels in the cylinder block. Lower the cylinder head onto the cylinder block.
2/5
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00654709
4. Inspect the condition of cylinder head bolts (1) and (2) . For information on the reusability
of the bolts, refer to Guideline For Reusable Parts And Salvage Operations, SEBF8301,
"Inspection and Reuse of Critical Fasteners Used in All Engines". Replace cylinder head
bolts (1) and (2) , if necessary.
5. Lubricate cylinder head bolts (1) and (2) and both sides of the washers with Tooling (A) .
Install cylinder head bolts (1) and (2) . Follow Step 6 for the correct tightening procedure.
Illustration 4 g00641677
3114 Cylinder head
3/5
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 5 g00611358
6. Tighten the cylinder head bolts according to the following procedure:
7. Tighten bolts (1) through bolt (14) in a numerical sequence to a torque of 300 ± 15 N·m
(221 ± 11 lb ft).
8. Loosen bolts (1) through bolt (14) to a torque of 0 N·m.
9. Tighten bolts (1) through bolt (14) again in a numerical sequence to a torque of 130 ± 15
N·m (96 ± 11 lb ft).
10. Retighten bolts (1) through bolt (14) again in a numerical sequence to a torque of 130 ± 15
N·m (96 ± 11 lb ft).
11. Turn bolts (1) through bolt (14) by numerical sequence an additional 90° (1/4 turn).
12. Tighten bolt (15) through bolt (20) in a numerical sequence to a torque of 55 ± 7 N·m (41 ±
5 lb ft).
End By:
a. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
b. Install the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold - Install".
c. Install the water temperature regulator housing. Refer to Disassembly and Assembly,
"Water Temperature Regulator Housing- Remove and Install".
d. Install the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Install".
e. Install the fuel control linkage. Refer to Disassembly and Assembly, "Fuel Injection Control
Linkage - Install".
f. Install the governor. Refer to Disassembly and Assembly, "Governor - Install".
g. Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove
and Install".
4/5
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:33:39 UTC+0800 2020
5/5
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930413
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/4
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Dispose of all fluids according to local regulations and mandates.
Note: For information on reusability of components of the lifter group, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8264, "Camshaft Roller Followers Used in 3114
and 3116 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8067,
"Slipper Followers and Camshaft Roller Followers".
Illustration 1 g00747310
1. Remove bolts (1) from cover (2).
2. Carefully remove cover (2) and the gasket.
Note: It may be necessary to remove the governor in order to remove the cover at the front
of the engine.
Illustration 2 g00629677
3. Remove bolts (4), lifter shaft (5), and lifters (3) from cover (2).
Installation Procedure
2/4
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of components of the lifter group, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8264, "Camshaft Roller Followers Used in 3114
and 3116 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8067,
"Slipper Followers and Camshaft Roller Followers".
Illustration 3 g00629677
1. Position lifters (3) and lifter shaft (5) on cover (2). Install bolts (4).
Illustration 4 g00747310
2. Position the gasket and cover (2) on the engine.
3. Install bolts (1) in cover (2).
End By:
3/4
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. a. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:34:35 UTC+0800 2020
4/4
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930426
Camshaft - Remove
SMCS - 1210-011
Removal Procedure
Start By:
a. Remove the governor. Refer to Disassembly and Assembly, "Governor - Remove".
b. Remove the side covers. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
c. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: For information on reusability of the camshaft, refer to Guideline For Reusable Parts And
Salvage Operations, SEBF8097, "Camshaft Measurement", Guideline For Reusable Parts And
Salvage Operations, SEBF8146, "Visual Inspection of Camshafts", and Guideline For Reusable
Parts And Salvage Operations, SEBF8251, "Specifications for Measurement of Camshafts in
3114/3116 Engines". For information on reusability of the camshaft gear, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
Note: The air compressor was removed in order to accommodate the engine repair stand.
Note: It is not necessary to remove the cylinder head for removal of the camshaft.
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. Install the timing
bolt in the flywheel. This is for timing during installation.
Illustration 1 g01007643
Typical example
2. Ensure that timing mark (1) on the camshaft gear is aligned with timing mark (2) on the
idler gear.
2/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 2 g01007645
3. Remove bolts (4) and camshaft retainer plate (6).
4. Remove camshaft gear (5) and camshaft (3) from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:35:31 UTC+0800 2020
3/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 5BS
Configuration: 325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01936378
Camshaft - Install
SMCS - 1210-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of the camshaft, refer to Guideline For Reusable Parts And
Salvage Operations, SEBF8097, "Camshaft Measurement", Guideline For Reusable Parts And
Salvage Operations, SEBF8146, "Visual Inspection of Camshafts", and Guideline For Reusable
Parts And Salvage Operations, SEBF8251, "Specifications for Measurement of Camshafts in
3114/3116 Engines". For information on reusability of the camshaft gear, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
1. Lubricate the camshaft and the camshaft bearings with clean engine oil.
1/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g01007645
2. Carefully install camshaft (3) and camshaft gear (5) in the engine.
NOTICE
When installing the camshaft, make sure the number one cylinder is at
top center of the compression stroke with the timing bolt installed in
the flywheel. The camshaft timing is very important. The timing mark
on the camshaft drive gear must line up with the timing mark on the
idler gear. Refer to the Specifications Manual for more information.
Illustration 2 g01007643
Typical example
3. Ensure that timing mark (1) on the camshaft gear is aligned with timing mark (2) on the
idler gear.
2/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 4. Install camshaft retainer plate (6) and bolts (4).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
b. Install the side cover. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
c. Install the governor. Refer to Disassembly and Assembly, "Governor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 23:36:27 UTC+0800 2020
3/3
325B L & 325B LN Excavators 5BS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...