This document provides instructions for servicing components of a Caterpillar 324D and 324D L excavator engine. It includes procedures for removing and installing various parts like the front housing, camshaft idler gear, valve mechanism cover, rocker shaft, and pushrods. The document emphasizes cleaning parts and contains warnings about containing fluids to prevent contamination. Detailed illustrations accompany each multi-step procedure to ensure correct part placement and fastener tightening specifications.
Caterpillar cat 324 d l excavator (prefix dfp) service repair manual (dfp0000...fjskekdmmem
This document provides instructions for servicing components of a 324D and 324D L excavator powered by a C7 engine. It describes procedures for removing and installing components such as the front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft, and pushrods. The document emphasizes keeping parts clean and contains illustrations to support the text instructions.
Caterpillar cat 324 d excavator (prefix dfp) service repair manual (dfp00001 ...fjskekdmmem
This document provides instructions for servicing components of a 324D and 324D L excavator powered by a C7 engine. It describes procedures for removing and installing components such as the front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft, and pushrods. The document emphasizes keeping parts clean and contains illustrations to support the text instructions.
This service repair manual provides instructions for repairing Caterpillar 324D and 324D L excavators with C7 engines. It describes procedures for removing and installing various engine components like the front housing, camshaft idler gear, valve mechanism cover, and valve mechanism cover base. The manual emphasizes keeping components clean and applying sealant and primer as specified. Tools required are also listed for each procedure.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...shudun96087
This service repair manual provides instructions for repairing Caterpillar 324D and 324D L excavators with C7 engines. It describes procedures for removing and installing various engine components like the front housing, camshaft idler gear, valve mechanism cover, and valve mechanism cover base. The manual emphasizes keeping components clean and applying sealant and primer as specified. Tools required are also listed for each procedure.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...qme229722
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...kesi7153062
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
Caterpillar cat 324 d l excavator (prefix dfp) service repair manual (dfp0000...fjskekdmmem
This document provides instructions for servicing components of a 324D and 324D L excavator powered by a C7 engine. It describes procedures for removing and installing components such as the front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft, and pushrods. The document emphasizes keeping parts clean and contains illustrations to support the text instructions.
Caterpillar cat 324 d excavator (prefix dfp) service repair manual (dfp00001 ...fjskekdmmem
This document provides instructions for servicing components of a 324D and 324D L excavator powered by a C7 engine. It describes procedures for removing and installing components such as the front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft, and pushrods. The document emphasizes keeping parts clean and contains illustrations to support the text instructions.
This service repair manual provides instructions for repairing Caterpillar 324D and 324D L excavators with C7 engines. It describes procedures for removing and installing various engine components like the front housing, camshaft idler gear, valve mechanism cover, and valve mechanism cover base. The manual emphasizes keeping components clean and applying sealant and primer as specified. Tools required are also listed for each procedure.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...shudun96087
This service repair manual provides instructions for repairing Caterpillar 324D and 324D L excavators with C7 engines. It describes procedures for removing and installing various engine components like the front housing, camshaft idler gear, valve mechanism cover, and valve mechanism cover base. The manual emphasizes keeping components clean and applying sealant and primer as specified. Tools required are also listed for each procedure.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...qme229722
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...kesi7153062
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies any required tools for each procedure. Technicians are instructed to keep all parts clean and free of contaminants to prevent premature wear during reassembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 324 d ln excavator (prefix kjr) service repair manual (kjr000...ifoseidkkd
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
Caterpillar Cat 345C and 345C L Hydraulic Excavator (Prefix PJW) Service Repa...fijsekkdmdm2w
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, applying anti-seize compound, installing various seals and gears, and adjusting bearing preload using shims. Precision is required to prevent damage to seals and ensure proper engagement of gears. Lifting devices and care are needed due to components weighing up to 127 kg.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336E and 336E L Excavator (Prefix KED) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for assembling a travel motor on an excavator. It describes 27 steps to assemble internal components like seals, springs, and bearings. These components include pistons, a cam plate, and a rotating assembly. The final steps connect the travel motor to the final drive and install exterior covers. Proper assembly requires using the correct tools and lubricants, and ensuring parts are aligned and torques are set correctly.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to disassemble the pump by removing components like bolts, sensors, valves, springs, pistons, gears, and bearings. The assembly section lists 48 steps to reinstall these components in reverse order, noting the need to heat some bearings before installation and ensure proper placement of pins, seals, and other parts. Precautions are provided for releasing spring forces. Required tools include various pliers, pins, and links to aid in removal and installation of components.
Caterpillar Cat 330F and 330F L Excavator (Prefix GHT) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling a 330F excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, brake piston, rotating assembly, pistons, seals, and other parts. Tools required include retaining ring pliers, a bearing puller, bolts, threaded rods, and other hardware. Safety precautions are provided to release spring forces carefully.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling the travel motor on a 336D2L excavator. It describes 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, springs, seals, relief valves, plugs, and more. Precautions are provided to watch for spring forces and contain fluids. Tools needed include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Reassembly will follow the disassembly steps in reverse order.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and over 15 additional parts. The goal is to allow maintenance and repair of these core powertrain systems.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 336D L Excavator (Prefix JBF) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for installing a unit injector sleeve on a Caterpillar C9 engine. It lists the required tools and gives step-by-step details for cleaning the sleeve and cylinder head bore, applying seals and retaining compound, and installing the sleeve using a hammer and installer tool. Proper installation is important to prevent leaks that could cause low pressure or excess oil consumption.
More Related Content
Similar to Caterpillar Cat 324D and 324D L Excavator (Prefix DFP) Service Repair Manual Instant Download.pdf
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies any required tools for each procedure. Technicians are instructed to keep all parts clean and free of contaminants to prevent premature wear during reassembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 324 d ln excavator (prefix kjr) service repair manual (kjr000...ifoseidkkd
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
Similar to Caterpillar Cat 324D and 324D L Excavator (Prefix DFP) Service Repair Manual Instant Download.pdf (10)
Caterpillar Cat 345C and 345C L Hydraulic Excavator (Prefix PJW) Service Repa...fijsekkdmdm2w
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, applying anti-seize compound, installing various seals and gears, and adjusting bearing preload using shims. Precision is required to prevent damage to seals and ensure proper engagement of gears. Lifting devices and care are needed due to components weighing up to 127 kg.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336E and 336E L Excavator (Prefix KED) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for assembling a travel motor on an excavator. It describes 27 steps to assemble internal components like seals, springs, and bearings. These components include pistons, a cam plate, and a rotating assembly. The final steps connect the travel motor to the final drive and install exterior covers. Proper assembly requires using the correct tools and lubricants, and ensuring parts are aligned and torques are set correctly.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to disassemble the pump by removing components like bolts, sensors, valves, springs, pistons, gears, and bearings. The assembly section lists 48 steps to reinstall these components in reverse order, noting the need to heat some bearings before installation and ensure proper placement of pins, seals, and other parts. Precautions are provided for releasing spring forces. Required tools include various pliers, pins, and links to aid in removal and installation of components.
Caterpillar Cat 330F and 330F L Excavator (Prefix GHT) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling a 330F excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, brake piston, rotating assembly, pistons, seals, and other parts. Tools required include retaining ring pliers, a bearing puller, bolts, threaded rods, and other hardware. Safety precautions are provided to release spring forces carefully.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling the travel motor on a 336D2L excavator. It describes 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, springs, seals, relief valves, plugs, and more. Precautions are provided to watch for spring forces and contain fluids. Tools needed include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Reassembly will follow the disassembly steps in reverse order.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and over 15 additional parts. The goal is to allow maintenance and repair of these core powertrain systems.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 336D L Excavator (Prefix JBF) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for installing a unit injector sleeve on a Caterpillar C9 engine. It lists the required tools and gives step-by-step details for cleaning the sleeve and cylinder head bore, applying seals and retaining compound, and installing the sleeve using a hammer and installer tool. Proper installation is important to prevent leaks that could cause low pressure or excess oil consumption.
Caterpillar Cat 926 and 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing the cylinder head assembly on a 3204 vehicular engine. It describes:
1) Removing the cylinder head assembly by loosening hoses, removing bolts, and lifting it off with a hoist.
2) Cleaning and installing a new gasket before lowering the cylinder head back onto the cylinder block and tightening bolts in a specific sequence and torque.
3) Checking the flatness of the cylinder head and block surfaces during installation.
This document provides instructions for disassembling and assembling the torque converter and transmission of a Caterpillar 938F wheel loader. It details removing over 40 individual parts in 21 steps to disassemble the torque converter. A further 44 steps describe disassembling the transmission by removing components like shafts, gears, seals, and clutches. Precise tools and lifting devices are specified to carefully remove heavy parts. Reassembly is outlined in reverse order with notes to check components for wear and replace as needed.
Caterpillar Cat 325C and 325C L Excavator (Prefix BKW) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs to clean all parts thoroughly, apply lubricants, and install the parts in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Tools required include a transmission repair stand, link brackets, retaining ring pliers, and other specialized tools.
This document provides instructions for disassembling and assembling the piston pump of a 623G wheel scraper. Some key steps include:
1. Marking all mating components for alignment during assembly.
2. Removing various seals, springs, spools, and other internal parts from the pump housing and head.
3. Checking the preload on bearings during assembly by measuring clearance between the pump head and housing.
4. Cleaning all parts thoroughly before assembly and applying a light oil film. Precise alignment of marked components is important.
This document provides instructions for disassembling and assembling axle shaft assemblies for a 938F wheel loader. It describes removing components like the axle housing groups, axle shaft assembly, planetary carrier assembly, and installing new components in reverse order. Key steps include using various tools to remove retaining rings, planetary gears, and installing new bearings and seals at specified temperatures while ensuring proper torque specifications are met.
The document provides instructions for removing and installing fuel injection pumps on a Caterpillar 3406C diesel engine. Key steps include using various tools to hold components in place, loosening and removing bushings, seals and pumps. Reinstallation involves aligning pins and slots, installing spacers and seals correctly, and checking rack travel measurements to ensure proper installation. The document also describes disassembling and assembling the fuel injection pumps and fuel injection pump housing.
The document provides step-by-step instructions for disassembling and assembling the final drives of a 350L excavator. Key steps include removing the final drives and travel motors, disassembling the internal components of the final drives which include multiple planetary gear sets, carriers, and a sun gear, and then reassembling the final drives in reverse order. Proper cleaning, application of lubricants, and torque specifications are noted throughout to ensure correct reassembly.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, brake piston, rotating group, and seals. The instructions describe taking identifying marks on parts and cleaning components to prevent contamination. Reassembly is done in reverse order.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302664
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
A. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
B. Remove the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit
Injector Hydraulic Pump - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g01153092
1. Support the weight of the front of the engine. Remove bolts (1) and front engine support
(2) .
Illustration 2 g01153093
2. Remove bolts (3) and bolts (5). Remove front housing (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:47:19 UTC+0800 2020
2/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302689
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-9011 Component Cleaner 1
B 4C-9500 Quick Cure Primer 1
C 1U-8846 Gasket Sealant 1
1/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 1 g01153093
1. Clean the joint face on front housing (4) with Tooling (A) .
2. Apply Tooling (B) to the joint face. Allow the primer to dry for at least three to five
minutes.
3. Apply Tooling (C) to the joint face. Spread the sealant uniformly. Front housing (4) must be
installed within ten minutes of applying the sealant.
4. Position front housing (4) on the cylinder block.
5. Install bolts (3) and bolts (5) .
Illustration 2 g01153092
6. Position front engine support (2) and install bolts (1) .
End By:
a. Install the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector
Hydraulic Pump - Install".
b. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:48:18 UTC+0800 2020
2/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02230724
Camshaft Idler Gear - Remove and Install
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 1 g01125301
1. Remove bolts (4) and retaining plate (1) .
2. Remove camshaft idler gear (2) .
3. Remove bolt (7) and idler shaft (3) from the cylinder block. Remove thrust plate (5) .
4. Use Tooling (A) and a suitable press to remove bearing (6) from camshaft idler gear (2) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 2 g01125304
1. Use Tooling (A) and a suitable press to install bearing (6) in camshaft idler gear (2). Install
the bearing until the bearing is 1.080 ± 0.250 mm (0.0425 ± 0.0098 inch) below the front
face of camshaft idler gear (2) .
2. Position thrust plate (5) and idler shaft (3) on the cylinder block. Install bolt (7). Tighten the
bolt to a torque of 70 ± 15 N·m (51 ± 11 lb ft).
3. Install camshaft idler gear (2) on idler shaft (3). Ensure that timing mark (8) is facing
outward. Align timing mark (8) with timing mark (9) on crankshaft drive gear (10) .
4. Position plate (1) and install bolts (4). Tighten the bolts to a torque of 70 ± 15 N·m (51 ± 11
lb ft).
End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:49:18 UTC+0800 2020
3/3
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302870
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01153188
1/3
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. 1. Remove bolts (1) .
2. Remove valve mechanism cover (2) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01153188
2/3
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 3 g00945775
1. Position valve mechanism cover (2) on the engine.
2. Install bolts (1). Tighten bolts (1) in a numerical sequence to a torque of 15 ± 3 N·m (11 ± 2
lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:50:17 UTC+0800 2020
3/3
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302895
Valve Mechanism Cover Base - Remove and Install
SMCS - 1120-010
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 1 g01153198
1. Disconnect harness assembly (4) from valve mechanism cover base (3) .
2. Disconnect harness assemblies (1) .
3. Remove bolts (2), valve mechanism cover base (3), and the gasket from the cylinder head.
Installation Procedure
2/4
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 2 g01153198
Illustration 3 g01127431
1. Position the gasket and valve mechanism cover base (3) on the cylinder head. Install bolts
(2) and tighten bolts (2) in a numerical sequence to the standard torque.
2. Connect harness assemblies (1) .
3/4
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. 3. Connect harness assembly (4) to valve mechanism cover base (3) .
End By: Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:51:16 UTC+0800 2020
4/4
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02303847
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Place identification marks on each rocker arm and on each pushrod in order to identify the
proper location in the engine for installation.
1/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 1 g01153544
2. Loosen rocker arm adjustment screws (4) .
3. Remove bolts (1), bolts (2), and rocker shaft (3) .
4. Remove inlet valve bridges (5) and pushrods (6) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:52:16 UTC+0800 2020
2/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02307337
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Start By:
a. Remove the rocker shaft. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 1 g01155738
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
Note: Place an identification mark on each of the components of the rocker shaft for
installation purposes.
1. Remove retaining ring (2).
2. Remove stand (3), inlet rocker arms (4), exhaust rocker arms (5), stands (6), and springs (7)
from the rocker shaft.
3. Remove dowel pin (8) and stand (9) from the rocker shaft.
4. Remove plug (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:53:15 UTC+0800 2020
2/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02307338
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Lubricate all of the components of the rocker shaft with clean engine oil.
1/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 1 g01155738
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install plug (1).
3. Install stand (9) and dowel pin (8) on the rocker shaft.
4. Install springs (7), stands (6), exhaust rocker arms (5), inlet rocker arms (4), and stand (3)
on the rocker shaft.
5. Install retaining ring (2).
End By:
a. Install the rocker shaft. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:54:14 UTC+0800 2020
2/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02303869
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-2998 Lubricant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 1 g01153544
1. Apply Tooling (A) to both ends of pushrods (6) .
2. Lubricate pushrods (6) with clean engine oil. Install pushrods (6) and inlet valve bridges
(5) .
3. Position rocker shaft (3). Install bolts (1) and bolts (2). Finger tighten bolts (1) and bolts (2).
Tighten bolts (2) and bolts (1) to standard torque.
4. Apply Tooling (A) to each of the button faces of the rocker arms.
5. Adjust the valve lash of the rocker arm by turning rocker arm adjustment screws (4). Refer
to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust".
End By: Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:55:14 UTC+0800 2020
2/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02303932
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
A. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
B. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
And Pushrod - Remove".
C. Remove the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
D. Remove the fan drive mounting group. Refer to Disassembly and Assembly, "Fan Drive
Mounting Group - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01153598
1. Disconnect harness assemblies (1), (2), (3), (4), and (5) .
Illustration 2 g01153599
2/4
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. 2. Disconnect hose assembly (6) and tube assembly (7) .
Illustration 3 g01153600
3. Disconnect tube assembly (8) and tube assembly (10) from turbocharger (9) .
Illustration 4 g01153645
4. Attach a suitable lifting device to cylinder head (11). The weight of cylinder head (11) is
approximately 175 kg (385 lb).
3/4
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...