This document provides assembly and disassembly instructions for the swing drive of 323E excavator models. It includes 21 steps to disassemble components like the sun gear, carrier assembly, ring gear, housing and shaft. It also includes assembly steps applying anti-seize compound and torque specifications. Tools required include retaining ring pliers, link brackets, sleeves, pullers and hydraulic equipment. Cleanliness is emphasized to prevent contamination of parts.
Caterpillar cat 385 c excavator (prefix kgb) service repair manual (kgb00001 ...fjkskefksmeme
This document provides the disassembly and assembly procedures for the travel motor of 385C and 385C L excavator models. The disassembly procedure involves 40 steps to dismantle the various components of the travel motor. These include removing the head, relief valves, spools, pistons, springs, seals, port plate, friction plates, barrel assembly and other internal parts. Precautions are provided to handle parts under spring tension. The assembly procedure consists of 12 steps to reinstall the components in reverse order. Cleanliness and applying a light film of oil to parts is emphasized.
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar cat 325 d mobile hyd power unit (prefix c3n) service repair manua...fikkskmmdm
The document provides instructions for removing and installing an alternator from an engine that is still installed in a machine. The procedure involves:
1. Disconnecting the positive battery terminal to prevent wiring damage.
2. Removing the belt from the alternator pulley.
3. Removing bolts securing the alternator and removing it from the engine.
4. Installing the new alternator using the securing bolts and adjusting the belt tension.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 323 e l excavator (prefix yrp) service repair manual (yrp0000...fjskefkemms
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides instructions for reassembling these components, including installing seals, bearings, and gears, and using shims to set proper bearing preload. Bolts and seals must be tightened to the specified torques.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar cat 16 h motor grader (prefix ats) service repair manual (ats0000...fjskefkemms
This document provides disassembly instructions for the transmission and transfer gears of a 16H Motor Grader. It lists over 60 steps and required tools to disassemble components such as the transmission control module, planetary group, sleeves, gears, bearings, seals, and housing. Detailed illustrations accompany each step to show how to remove parts and subassemblies like the gear pump, coupling assembly, manifold, and housing. Safety precautions are provided for steps involving compressed springs.
Caterpillar cat 329 e l excavator (prefix rld) service repair manual (rld0000...fikkskmmdm
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar cat 385 c excavator (prefix kgb) service repair manual (kgb00001 ...fjkskefksmeme
This document provides the disassembly and assembly procedures for the travel motor of 385C and 385C L excavator models. The disassembly procedure involves 40 steps to dismantle the various components of the travel motor. These include removing the head, relief valves, spools, pistons, springs, seals, port plate, friction plates, barrel assembly and other internal parts. Precautions are provided to handle parts under spring tension. The assembly procedure consists of 12 steps to reinstall the components in reverse order. Cleanliness and applying a light film of oil to parts is emphasized.
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar cat 325 d mobile hyd power unit (prefix c3n) service repair manua...fikkskmmdm
The document provides instructions for removing and installing an alternator from an engine that is still installed in a machine. The procedure involves:
1. Disconnecting the positive battery terminal to prevent wiring damage.
2. Removing the belt from the alternator pulley.
3. Removing bolts securing the alternator and removing it from the engine.
4. Installing the new alternator using the securing bolts and adjusting the belt tension.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 323 e l excavator (prefix yrp) service repair manual (yrp0000...fjskefkemms
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides instructions for reassembling these components, including installing seals, bearings, and gears, and using shims to set proper bearing preload. Bolts and seals must be tightened to the specified torques.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar cat 16 h motor grader (prefix ats) service repair manual (ats0000...fjskefkemms
This document provides disassembly instructions for the transmission and transfer gears of a 16H Motor Grader. It lists over 60 steps and required tools to disassemble components such as the transmission control module, planetary group, sleeves, gears, bearings, seals, and housing. Detailed illustrations accompany each step to show how to remove parts and subassemblies like the gear pump, coupling assembly, manifold, and housing. Safety precautions are provided for steps involving compressed springs.
Caterpillar cat 329 e l excavator (prefix rld) service repair manual (rld0000...fikkskmmdm
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
Caterpillar cat 329 e excavator (prefix k2l) service repair manual (k2l00001 ...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
Caterpillar cat 326 d2 l excavator (prefix rec) service repair manual (rec000...fikkskmmdm
This document provides instructions to disassemble a final drive on an excavator. It outlines 33 steps to fully disassemble the final drive. Key steps include removing the cover, carrier assembly, planetary gears, and separating the main housing from the motor housing. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components. Cleanliness is important to prevent dirt from entering during reassembly.
Caterpillar cat 323 e l excavator (prefix rap) service repair manual (rap0000...fjskefkemms
The document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes steps to disassemble and remove the final drive components, such as the carrier assembly, ring gears, planetary gears, and seals. It also provides instructions for assembling the final drive, including pressing bearings into place, determining the correct shim thickness, installing seals and pins, and reassembling the carrier assembly. Tools required include lifting devices, presses, seal installers, and other specialized tools. Proper torque values and procedures are specified for reinstalling components.
Caterpillar cat 330 b l excavator (prefix 5lr) service repair manual (5lr0000...fjskefkemms
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the components and steps in the process.
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1. The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2. The installation procedure specifies using the same special tool to install the bearings at precise depths in the cylinder block and checking the bore size after installation.
3. Reinstalling components like the flywheel housing, balancer shaft, and oil pan completes the process.
Caterpillar cat 330 a l excavator (prefix 5 ym) service repair manual (5ym000...fjskefkemms
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w006...fjsekdmmeed
1) The document provides step-by-step instructions for disassembling and assembling the governor component of a 3304 engine. It includes 34 steps for disassembly and 33 steps for assembly.
2) Required tools include a driver group, spring clamp, and retaining ring pliers. Cleanliness is emphasized to prevent contaminants from causing wear.
3) Key parts that are disassembled and assembled include the governor shaft, carrier, flyweights, dashpot assembly, valve, piston, and governor servo. Detailed illustrations accompany each step.
Caterpillar cat 330 c mh excavator (prefix d3c) service repair manual (d3c000...jfdskekdmme
1) The document provides disassembly and assembly instructions for a 330C excavator travel motor.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
3) It then describes 13 steps for assembling the travel motor, including installing seals, bearings, springs, and securing components with bolts, pins, and retaining rings.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
The document provides instructions for removing and installing a pump drive on a C18 Industrial Engine. It includes:
1) A list of required tools and safety notices for working on the engine.
2) Step-by-step instructions to disassemble the pump drive by removing components like bolts, gears, and bearings.
3) Parallel steps for reassembling the pump drive, including installing new seals and adjusting end play clearances.
4) Instructions for installing the completed pump drive back onto the engine using lifting equipment due to component weights.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjskefkemms
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate removal and installation.
2. Camshaft removal and installation.
3. Camshaft bearing removal and installation.
4. Connecting rod bearing removal and installation.
5. Crankshaft main bearing removal and installation.
The instructions describe the individual steps for removing and installing each component, including the use of any necessary tools. Safety notices and additional notes are also provided throughout.
The document provides the disassembly procedure for a 330D2 excavator travel motor. It lists 28 steps to fully disassemble the travel motor, including removing the head, brake piston, plates and discs, rotating assembly, seals, and other internal components. Tools required are also listed. The procedure aims to clearly identify each part and ensure proper reinstallation of components in their original positions and orientations.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...fkjsekksmem
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
This document is an operation and maintenance manual for a Hitachi 70Z7 wheel loader. It provides safety information and instructions for operating, maintaining, and transporting the machine. The manual emphasizes following all safety procedures to prevent injuries or damage to the equipment. It also contains sections on machine identification numbers, component names, specifications, and troubleshooting.
Caterpillar cat d5 c d5c lgp xl series iii tractor dozer bulldozer (prefix 8z...fikkskkdmmd
The document provides instructions for removing and installing track carrier rollers and track rollers on D5C series tractors. It describes loosening the track, removing bolts and covers to access the rollers, lifting the track or machine to remove the rollers, and reversing the process to install new rollers and adjust the track. Proper cleaning, lubrication and torque specifications are noted to ensure correct assembly.
Caterpillar cat 385 c l excavator (prefix kgb) service repair manual (kgb0000...fikkskkdmmd
This document provides instructions for disassembling and assembling the travel motor on 385C and 385C L Excavator models. The disassembly procedure involves 40 steps to remove components like the head, relief valves, spools, pistons, plates, seals and more. The assembly procedure reverses the disassembly with 13 steps, including cleaning parts, applying oil, and ensuring proper installation of springs, seals and other components. Precautions are provided to prevent injury from parts under pressure.
Caterpillar cat 330 l track type excavator (prefix 6wj) service repair manual...fikkskkdmmd
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes removing the travel motor by draining oil, releasing hydraulic pressure, removing mounting bolts and hoses, and using a hoist. It then describes disassembling and assembling the travel motor by removing components like the head assembly, valves, springs, seals and pistons. Reinstallation involves cleaning, installing new seals, and reversing the removal steps while taking care not to damage components.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
Caterpillar cat 329 e excavator (prefix k2l) service repair manual (k2l00001 ...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
Caterpillar cat 326 d2 l excavator (prefix rec) service repair manual (rec000...fikkskmmdm
This document provides instructions to disassemble a final drive on an excavator. It outlines 33 steps to fully disassemble the final drive. Key steps include removing the cover, carrier assembly, planetary gears, and separating the main housing from the motor housing. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components. Cleanliness is important to prevent dirt from entering during reassembly.
Caterpillar cat 323 e l excavator (prefix rap) service repair manual (rap0000...fjskefkemms
The document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes steps to disassemble and remove the final drive components, such as the carrier assembly, ring gears, planetary gears, and seals. It also provides instructions for assembling the final drive, including pressing bearings into place, determining the correct shim thickness, installing seals and pins, and reassembling the carrier assembly. Tools required include lifting devices, presses, seal installers, and other specialized tools. Proper torque values and procedures are specified for reinstalling components.
Caterpillar cat 330 b l excavator (prefix 5lr) service repair manual (5lr0000...fjskefkemms
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the components and steps in the process.
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1. The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2. The installation procedure specifies using the same special tool to install the bearings at precise depths in the cylinder block and checking the bore size after installation.
3. Reinstalling components like the flywheel housing, balancer shaft, and oil pan completes the process.
Caterpillar cat 330 a l excavator (prefix 5 ym) service repair manual (5ym000...fjskefkemms
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w006...fjsekdmmeed
1) The document provides step-by-step instructions for disassembling and assembling the governor component of a 3304 engine. It includes 34 steps for disassembly and 33 steps for assembly.
2) Required tools include a driver group, spring clamp, and retaining ring pliers. Cleanliness is emphasized to prevent contaminants from causing wear.
3) Key parts that are disassembled and assembled include the governor shaft, carrier, flyweights, dashpot assembly, valve, piston, and governor servo. Detailed illustrations accompany each step.
Caterpillar cat 330 c mh excavator (prefix d3c) service repair manual (d3c000...jfdskekdmme
1) The document provides disassembly and assembly instructions for a 330C excavator travel motor.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
3) It then describes 13 steps for assembling the travel motor, including installing seals, bearings, springs, and securing components with bolts, pins, and retaining rings.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
The document provides instructions for removing and installing a pump drive on a C18 Industrial Engine. It includes:
1) A list of required tools and safety notices for working on the engine.
2) Step-by-step instructions to disassemble the pump drive by removing components like bolts, gears, and bearings.
3) Parallel steps for reassembling the pump drive, including installing new seals and adjusting end play clearances.
4) Instructions for installing the completed pump drive back onto the engine using lifting equipment due to component weights.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjskefkemms
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate removal and installation.
2. Camshaft removal and installation.
3. Camshaft bearing removal and installation.
4. Connecting rod bearing removal and installation.
5. Crankshaft main bearing removal and installation.
The instructions describe the individual steps for removing and installing each component, including the use of any necessary tools. Safety notices and additional notes are also provided throughout.
The document provides the disassembly procedure for a 330D2 excavator travel motor. It lists 28 steps to fully disassemble the travel motor, including removing the head, brake piston, plates and discs, rotating assembly, seals, and other internal components. Tools required are also listed. The procedure aims to clearly identify each part and ensure proper reinstallation of components in their original positions and orientations.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...fkjsekksmem
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
This document is an operation and maintenance manual for a Hitachi 70Z7 wheel loader. It provides safety information and instructions for operating, maintaining, and transporting the machine. The manual emphasizes following all safety procedures to prevent injuries or damage to the equipment. It also contains sections on machine identification numbers, component names, specifications, and troubleshooting.
Caterpillar cat d5 c d5c lgp xl series iii tractor dozer bulldozer (prefix 8z...fikkskkdmmd
The document provides instructions for removing and installing track carrier rollers and track rollers on D5C series tractors. It describes loosening the track, removing bolts and covers to access the rollers, lifting the track or machine to remove the rollers, and reversing the process to install new rollers and adjust the track. Proper cleaning, lubrication and torque specifications are noted to ensure correct assembly.
Caterpillar cat 385 c l excavator (prefix kgb) service repair manual (kgb0000...fikkskkdmmd
This document provides instructions for disassembling and assembling the travel motor on 385C and 385C L Excavator models. The disassembly procedure involves 40 steps to remove components like the head, relief valves, spools, pistons, plates, seals and more. The assembly procedure reverses the disassembly with 13 steps, including cleaning parts, applying oil, and ensuring proper installation of springs, seals and other components. Precautions are provided to prevent injury from parts under pressure.
Caterpillar cat 330 l track type excavator (prefix 6wj) service repair manual...fikkskkdmmd
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes removing the travel motor by draining oil, releasing hydraulic pressure, removing mounting bolts and hoses, and using a hoist. It then describes disassembling and assembling the travel motor by removing components like the head assembly, valves, springs, seals and pistons. Reinstallation involves cleaning, installing new seals, and reversing the removal steps while taking care not to damage components.
Caterpillar cat 330 l track type excavator (prefix 6sk) service repair manual...fikkskkdmmd
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a Caterpillar 330L excavator engine. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and properly dispose of fluids.
Caterpillar cat 330 l excavator (prefix 9ml) service repair manual (9ml00001 ...fikkskkdmmd
The document provides instructions for installing a fuel injection pump on a Caterpillar 330 excavator engine:
1. Install alignment tools and spacers to hold the fuel injection pump and rack in position.
2. Install the fuel injection pump, ensuring slots are aligned. Install an O-ring seal and bushing, tightening to the specified torque.
3. Use a measurement tool to check the rack travel and ensure proper installation of the fuel injection pump. Repeat steps for remaining pumps. Install the cover.
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fikkskkdmmd
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker assembly.
2. Remove bolts securing the cylinder head and lift it off using a lifting device.
3. To install, place a new gasket and bolt the clean cylinder head to the engine block. Reinstall attached components and adjust valve lash.
Caterpillar cat 330 l excavator (prefix 5ym) service repair manual (5ym00001 ...fikkskkdmmd
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fikkskkdmmd
This document provides instructions for installing a cylinder head and camshaft on a 330C FM EXCAVATOR powered by a C-9 engine. It outlines the required tools and lubricants, installation steps including tightening bolt sequences and torque specifications, and ensuring proper timing of gears. The summary focuses on the key steps of positioning the cylinder head and camshaft, applying lubricant, aligning timing marks between gears, and verifying end play clearance.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fikkskkdmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 330C FM EXCAVATOR including:
- Cylinder head removal which requires draining coolant and removing accessories before removing bolts and lifting off the head.
- Cylinder head installation which involves positioning a new gasket and torquing bolts in a specific sequence.
- Lifter group removal by using a hook tool to remove individual lifters and mark them for installation.
- Lifter group installation by applying lubricant to lifters before reinstalling them in the original locations.
- Camshaft removal which requires setting the #1 piston at top center and aligning timing
Caterpillar cat 330 b ln excavator (prefix 5lr) service repair manual (5lr000...fikkskkdmmd
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and torquing bolts to specifications. Technicians are advised to keep parts clean and mark components for original locations during disassembly and reinstallation.
Caterpillar cat 330 b ln excavator (prefix 3yr) service repair manual (3yr000...fikkskkdmmd
The document provides instructions for servicing components of a 330B L excavator, including:
1. Instructions for installing a compression brake on the engine, including connecting wires and bolts.
2. Procedures for removing and disassembling the rocker shaft and pushrods, including identifying pushrod locations and removing retaining rings and supports.
3. Steps for assembling the rocker shaft, including installing supports, springs, washers and an O-ring seal.
Caterpillar cat 330 b l excavator (prefix 6dr) service repair manual (6dr0000...fikkskkdmmd
The documents provide instructions for removing and installing various engine components on a 330B L Excavator with a 3306 engine. The steps include removing the cylinder head by first taking off the fuel injection lines. The rocker shaft is then disassembled by removing the rocker arms, springs and supports. The rocker shaft is assembled by installing these parts in the reverse order. Finally, the rocker shaft and pushrods are installed on the cylinder head and the valve lash is adjusted.
Caterpillar cat 330 b l excavator (prefix 5lr) service repair manual (5lr0000...fikkskkdmmd
This service repair manual provides instructions for installing a cylinder head on a 330B LN excavator engine. It describes cleaning the cylinder head and block surfaces, installing new gaskets and bolts, and tightening the bolts in a specific sequence. It also covers removing and installing related components like the spacer plate, water directors, and lifter group.
Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr0000...fikkskkdmmd
The document provides instructions for removing and installing various engine components on a Caterpillar 330B L excavator. It includes steps for removing and installing the cylinder head, rocker shaft and pushrods, compression brake, and valve mechanism cover. Technicians are advised to keep parts clean, apply lubricant to threads, and torque bolts to the specified values.
Caterpillar cat 330 b l excavator (prefix 1js) service repair manual (1js0000...fikkskkdmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 330B L excavator engine. The procedure involves using a special tool to extract the old seat inserts and press in the new ones. Technicians are advised to keep all parts clean and lubricated to prevent wear during reassembly.
Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml000...fikkskkdmmd
The document provides instructions for installing a fuel injection pump on a Caterpillar 330 excavator engine:
1. Install alignment tools and spacers to hold the fuel injection pump and rack in position.
2. Install the fuel injection pump, O-ring seal, and bushing, and tighten to the specified torque.
3. Use a measurement tool to check that the rack has the correct travel of 15.70 mm after installation.
Caterpillar cat 330 a l excavator (prefix 5 ym) service repair manual (5ym000...fikkskkdmmd
The document provides instructions for removing and installing various engine components, including:
1) Removing the cylinder head which involves first removing the fuel injection lines and exhaust manifold.
2) Instructions for disassembling the rocker shaft which includes removing rocker arms, springs, and supports.
3) Procedures for assembling the rocker shaft by installing the rocker arms, supports, springs and securing with a pin and plugs.
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...fikkskkdmmd
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes removing the travel motor by draining oil, releasing hydraulic pressure, removing mounting bolts and hoses, and using a hoist. It then describes disassembling and assembling the travel motor by removing components like the head assembly, valves, springs, seals and pistons. Reinstallation involves cleaning, installing new seals, and reversing the removal steps while taking care not to damage components.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fikkskkdmmd
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a Caterpillar 330L excavator engine. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and properly dispose of fluids.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323E LN EXCAVATOR TDW
Configuration: 323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04609390
Swing Drive
SMCS - 5459
Specifications
Illustration 1 g02724358
Table 1
Specification for 148-4679 Swing Drive Gp
Item Qty Part Specification Description
1 1 Torque to 45.0 ± 4.5 N·m (33.2 ± 3.3 lb ft).
1/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 227-6221
Breather As
2 1
114-1399
Gauge Pipe Torque to 60 ± 6 N·m (44 ± 4 lb ft).
3 - -
Apply blue Loctite High Flex GM to the mating surfaces of the ring
gear and the housing.
4 - -
Surfaces of the mounting area, contact area of the bolt and surfaces of
the pinion shaft must be free of paint. Before assembly, the contact
surfaces of the bolt, the washer, and the tightened parts must be clean
and free of protective coating and oil.
Disassembly Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5P-1863 Retaining Ring Pliers 1
B 138-7575 Link Brackets 2
C
4C-5660 Adapter 2
5F-7369 Puller Leg 2
3H-0465 Push-Puller Plate 2
1P-0820 Hydraulic Puller 1
3H-0468 Puller Plate 2
350-7768 Electric Hydraulic Pump Gp(1)
1
1U-9889 Crossblock 1
D 138-7573 Link Brackets 2
E FT-3023 Sleeve 1
F
5F-7343 Bearing Puller Gp 1
3H-0465 Push-Puller Plate 4
5F-7369 Puller Leg 2
5F-7342 Adapter 2
1P-0820 Hydraulic Puller 1
350-7768 Electric Hydraulic Pump Gp(1)
1
(1)
350-7769 (230 V)
2/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Start By:
a. Remove the swing motor and swing drive.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will prevent dirt from entering the internal
mechanism.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Illustration 2 g00702449
1. Remove sun gear (1) from carrier assembly (2).
3/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 3 g00702450
2. Remove spacer (3).
Illustration 4 g00702451
3. Remove carrier assembly (2) from ring gear (4).
Illustration 5 g00702452
4. Drive roll pin (5) into shaft (6). Remove shaft (6) and the gear assembly.
4/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g00702456
5. Disassemble the gear assembly, as follows: washer (7), gear (8), bearing (9), and washer (10).
Remove roll pin (5) from shaft (6).
6. Repeat Step 4 through Step 5 for the remaining gear assemblies.
Illustration 7 g00702457
7. Remove retaining ring (11). Remove carrier (13) from the sun gear.
Illustration 8 g00702459
8. Use Tooling (A) in order to remove retaining ring (14).
5/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 9 g00702583
9. Use two people in order to remove ring gear (15) from housing (16). The weight of ring gear
(15) is approximately 29 kg (65 lb).
Illustration 10 g00702584
10. Remove spacer (17) from carrier assembly (18).
Illustration 11 g00702596
11. Use Tooling (A) to remove retaining ring (19).
6/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g01338951
12. Remove carrier assembly (18) from the housing. The weight of carrier assembly (18) is
approximately 25 kg (55 lb).
Illustration 13 g00702640
13. Drive roll pin (20) into shaft (21). Remove shaft (21).
Illustration 14 g00702648
14. Disassemble the gear assembly, as follows: washer (22), bearing (23), gear (24), bearing (25),
and washer (26). Remove roll pin (20) from shaft (21).
15. Repeat Step 13 through Step 14 for the remaining gear assemblies.
7/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g01339732
16. Remove bolts (27) from the housing.
Illustration 16 g01339903
Illustration 17 g01339833
17. Attach Tooling (B) and a suitable lifting device in order to remove housing (28). The weight of
housing (28) is approximately 68 kg (150 lb). If shaft assembly (29) is stuck in housing (28)
install Tooling (C) in order to remove shaft assembly (29).
8/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g01338949
Illustration 19 g01339781
Illustration 20 g01339877
18. Use Tooling (A) in order to install retaining ring (19). Attach a suitable lifting device to shaft
assembly (29). The weight of shaft assembly (29) is approximately 45 kg (100 lb). Position
shaft assembly (29) onto Tooling (E). Install Tooling (D).
19. Position Tooling (E) and shaft assembly (29) as a unit into a suitable press. The weight of
Tooling (E) and the shaft assembly (29) is approximately 93 kg (205 lb). Use Tooling (A) in
order to remove retaining ring (19). Remove bearings (30) and spacer (31).
Note: If excessive force is required to remove bearings, use Tooling (F) in order to remove the
top bearing first.
9/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g01338948
20. Attach a suitable lifting device to Tooling (D) in order to remove cage (33) and Tooling (E).
Remove cage (33) and Tooling (E) from shaft (32).
Illustration 22 g01340053
21. Remove O-ring seal (34). Remove lip seals (35).
Assembly Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
A 5P-1863 Retaining Ring Pliers 1
B 138-7575 Link Brackets 2
D 138-7573 Link Brackets 2
E FT-3023 Sleeve 1
G 1P-0520 Driver Gp 1
H 5P-3931 Anti-Seize Compound 1
J 8M-4856 (1)
Sleeve 1
10/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. K -
Guide Stud
M16 - 2.00 by 140mm
2
L - Loctite Hi Flex GM 1
(1)
This part is being discontinued. Replace with 367-6742 Sleeve .
Note: Cleanliness is an important factor. Before assembly, clean all parts in cleaning fluid. Allow the
parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the
parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts
for replacement.
Illustration 23 g01339794
Illustration 24 g01339807
1. Use a suitable press and Tooling (G) in order to install lip seal (35) into cage (33).
2. Use two people to place shaft (32) in a suitable press. The weight of shaft (32) is approximately
30 kg (65 lb). Install cage (33). Install O-ring seal (34).
11/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 25 g01339812
Illustration 26 g01339149
3. Apply Tooling (H) to inner diameter of the bearing and the shaft. Use a suitable press and
Tooling (J) in order to install bearing (30). Install spacer (31). The bevel of the spacer must
face upward.
4. Install bearing (30).
Illustration 27 g01339824
12/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 28 g01339903
5. Attach a suitable lifting device to shaft assembly (29). Use Tooling (A) in order to install
retaining ring (19). Install shaft assembly (29) onto Tooling (E). Remove the suitable lifting
device.
6. Attach Tooling (B) and a suitable lifting device to housing (28). Install housing (28) on the
shaft assembly. Position the shaft assembly to the side by 90 degrees. Remove tooling (E).
Illustration 29 g01339732
7. Install bolts (27).
Illustration 30 g00703698
13/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 8. Assemble the gear assembly, as follows: washer (22), bearing (23), gear (24), bearing (25), and
washer (26).
Illustration 31 g00702640
Illustration 32 g00703700
9. Use a deburring tool in order to remove the metal burr from the openings in the carrier. Install
shaft (21) and the gear assembly into the carrier assembly. Drive roll pin (20) into shaft (21).
Orient the split in roll pin (20) vertically to the carrier. Align the split in the roll pin to the top
or to the bottom. Make a stake mark on each side of the roll pin hole in the carrier. Each stake
mark should be approximately 2.25 ± 0.75 mm (0.090 ± 0.030 inch) from the outside diameter
of the roll pin hole.
10. Repeat Step 8 through Step 9 for the remaining gear assemblies.
14/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 33 g01338951
11. Install carrier assembly (18) into the housing. The weight of carrier assembly (18) is
approximately 25 kg (55 lb).
Illustration 34 g00702596
12. Use Tooling (A) to install retaining ring (19).
Illustration 35 g00702584
13. Install spacer (17) into carrier assembly (18).
15/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 36 g01340279
Illustration 37 g00702583
14. Apply Tooling (L) to the face of housing (16). Install Tooling (K) in order to help align the
housing and the ring gear. Use two people in order to install ring gear (15) onto housing (16).
The weight of ring gear (15) is approximately 29 kg (65 lb).
Illustration 38 g00702459
15. Install retaining ring (14) into the sun gear.
16/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 39 g00702457
16. Install carrier (13) into the sun gear. Install retaining ring (11) into sun gear (12).
Illustration 40 g00703707
17. Assemble the gear assembly, as follows: washer (7), gear (8), bearing (9), and washer (10)
Illustration 41 g00702452
17/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 42 g00703700
18. Use a deburring tool in order to remove the metal burr from the openings in the carrier. Install
shaft (6) and the gear assembly into the carrier assembly. Drive roll pin (5) into shaft (6).
Orient the split in roll pin (5) vertically to the carrier. Align the split in the roll pin to the top or
to the bottom. Make a stake mark on each side of the roll pin hole in the carrier. Each stake
mark should be approximately 2.25 ± 0.75 mm (0.090 ± 0.030 inch) from the outside diameter
of the roll pin hole.
19. Repeat Step 17 through Step 18 for the remaining gear assemblies.
Illustration 43 g00702451
20. Install carrier assembly (2) into ring gear (4).
18/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 44 g00702450
21. Install spacer (3).
Illustration 45 g00702449
22. Install sun gear (1) into carrier assembly (2).
End By:
a. Install the swing motor and swing drive.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 12 14:12:36 UTC+0800 2020
19/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323E LN EXCAVATOR TDW
Configuration: 323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04491082
Swing Gear and Bearing
SMCS - 7063
Specifications
1/4
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g02724727
Typical example
Table 1
Specification for 333-2969 Gear and Bearing Gp and 333-2966 Gear and Bearing Gp
Item Qty Part Specification Description
- - -
Position "S" that is on inner race (12) relative to the carbody
assembly (1) and bearing stopper (2). Refer to Illustration 1.
- - - The five holes which are marked “3” are not for use.
4 4 8T-4136
Bolt
Apply blue Loctite 242 to the threads.
Torque to 20 ± 2 N·m (177 ± 18 lb in).
2/4
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 5 8
8T-4136
Bolt
Apply blue Loctite 242 to the threads.
Torque to 37 ± 4 N·m (27 ± 3 lb ft).
6 1
7Y-1650
Hose
Clamp
Torque to 5.39 ± 0.49 N·m (47.71 ± 4.34 lb in).
7 2
8T-4137
Bolt
Apply blue Loctite 242 to the threads.
Torque to 37 ± 4 N·m (27 ± 3 lb ft).
8 1
096-4902
Dowel
Apply Loctite C5A Cooper Anti-Seize to the dowel holes.
9 - -
Apply blue Loctite High Flex GM between the mating surfaces of
the gear group and upper frame assembly. Apply blue Loctite High
Flex GM between the mating surfaces of the gear group and
carbody assembly.
10 37
8T-0362
Bolt
Apply Loctite C5A Cooper Anti-Seize to the threads. Omit the bolt
seats and surfaces of the washers.
Torque for the bolts except for the Akashi facility to 568 ± 59 N·m
(419 ± 44 lb ft).
Torque for the bolts for the Akashi facility to 294 ± 29 N·m
(217 ± 21 lb ft).
Additional torque for the bolts for the Akashi facility to 50 ± 5
degrees.
11 40
8T-0360
Bolt
Apply Loctite C5A Cooper Anti-Seize to the threads. Omit the bolt
seats and surfaces of the washers.
Torque for the bolts except for the Akashi facility to 568 ± 59 N·m
(419 ± 44 lb ft).
Torque for the bolts for the Akashi facility to 294 ± 29 N·m
(217 ± 21 lb ft).
Additional torque for the bolts for the Akashi facility to 50 ± 5
degrees.
Removal Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7576 Link Bracket 4
B -
Guide Bolts
M20 x 2.5 by 150mm
2
Start By:
a. Separate the upper frame from the undercarriage frame.
3/4
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. 1. Remove all the grease from the swing gear and bearing. Put the grease in a suitable
container for storage or disposal.
Illustration 2 g02672179
2. Remove bolts (1). Install bolts and mark swing gear and bearing (2) or alignment purposes
Illustration 3 g02672908
3. Attach Tooling (A) and a suitable lifting device in order to remove swing gear and bearing
(2) from the undercarriage (3).
Installation Procedure
1. Install swing gear and bearings (2) in reverse order of removal.
End By:
a. Connect the upper frame from the undercarriage frame.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 12 14:13:35 UTC+0800 2020
4/4
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323E LN EXCAVATOR TDW
Configuration: 323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04507920
Pilot Valve
SMCS - 5059
Removal Procedure
Start By:
a. Release the hydraulic system pressure.
Illustration 1 g02686500
1. Disconnect all hose assemblies (1). Disconnect all harness assemblies (2).
1/2
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 2 g02686503
2. Remove four bolts (3) and pilot valve (4).
Installation Procedure
1. Install pilot valve (4) in reverse order of removal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 12 14:14:35 UTC+0800 2020
2/2
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...