This document provides instructions for removing and installing the crankshaft gear on a Caterpillar 3126B engine. It lists the required tools and gives step-by-step procedures for removing the crankshaft, removing the crankshaft gear using a bearing puller, cleaning the surfaces, installing the crankshaft gear, and reinstalling the crankshaft. The procedures are part of a service repair manual for a 322C FM excavator.
Caterpillar cat 322 c fm excavator (prefix lar) service repair manual (lar000...fjskekfkemm
This document provides instructions for removing and installing the crankshaft gear on a Caterpillar 3126B engine. It lists the required tools and gives the step-by-step removal and installation procedures. The crankshaft must first be removed according to a separate procedure. A hydraulic puller or bearing puller is then used to detach the gear from the crankshaft, taking care to keep all parts clean from contamination. Reinstallation requires aligning and pressing the gear onto the crankshaft shaft.
Caterpillar cat 322 c fm excavator (prefix lar) service repair manual (lar000...ujjfkskeksmem
This document provides instructions for installing and removing the crankshaft main bearings on a Caterpillar 3126B engine. It outlines the required tools and steps to install the upper and lower main bearing halves into the cylinder block and crankshaft main bearing caps. Technicians are instructed to check the crankshaft end play once installed using a dial indicator. The summary also includes removing the crankshaft, which must be done before removing the crankshaft gear.
Caterpillar cat 325 c mobile hyd power unit (prefix msg) service repair manua...f98soeodidkdk
The document provides instructions for removing and installing a crankshaft gear on a 3126B engine. It lists the required tools and steps to remove the crankshaft first before removing the gear using a bearing puller. The installation procedure is not described.
Caterpillar Cat 325C MOBILE HYD POWER UNIT (Prefix MSG) Service Repair Manual...yan77xunhao
This document provides instructions for installing a crankshaft in a 3126B engine used in a 325C Mobile Hydraulic Power Unit. The instructions include:
1) Cleaning the cylinder block bearing surfaces and applying oil to the upper main bearings.
2) Installing the lower crankshaft main bearing halves into the bearing caps and installing the caps onto the cylinder block.
3) Checking crankshaft end play with a dial indicator to ensure it is within specifications.
Caterpillar Cat 325C MOBILE HYD POWER UNIT (Prefix MSG) Service Repair Manual...jfkskmdmmdd
The document provides instructions for removing and installing a crankshaft gear on a 3126B engine. It lists the required tools and steps to remove the crankshaft first before removing the gear using a bearing puller. The installation procedure is not described.
Caterpillar Cat 325C MOBILE HYD POWER UNIT (Prefix MSG) Service Repair Manual...jfkskmmdmdm
This document provides instructions for installing a crankshaft in a 3126B engine used in a 325C Mobile Hydraulic Power Unit. The instructions include:
1) Cleaning the cylinder block bearing surfaces and applying oil to the upper main bearings.
2) Installing the lower crankshaft main bearing halves into the bearing caps and installing the caps onto the cylinder block.
3) Checking crankshaft end play with a dial indicator to ensure it is within specifications.
Caterpillar cat 325 c mobile hyd power unit (prefix msg) service repair manua...fjsjjekdkme
The document provides instructions for removing and installing a crankshaft gear on a 3126B engine. It lists the required tools and begins by instructing the user to first remove the crankshaft by following the procedure in another document. The removal procedure then instructs the user to use a bearing puller and hydraulic pump to pull the gear off the crankshaft. The installation procedure is not shown, but presumably provides instructions for pressing the gear back onto the crankshaft.
Caterpillar cat 320 d l excavator (prefix jfz) service repair manual (jfz0000...fjjsefkksemm
This document provides instructions for removing and installing various components of the flywheel and crankshaft area of a Caterpillar C6.4 engine, including the flywheel, flywheel housing, crankshaft rear seal, and crankshaft pulley. The procedures include using various specialty tools and taking precautions such as cleaning parts and applying retaining compounds. Detailed illustrations are provided to supplement the text instructions.
Caterpillar cat 322 c fm excavator (prefix lar) service repair manual (lar000...fjskekfkemm
This document provides instructions for removing and installing the crankshaft gear on a Caterpillar 3126B engine. It lists the required tools and gives the step-by-step removal and installation procedures. The crankshaft must first be removed according to a separate procedure. A hydraulic puller or bearing puller is then used to detach the gear from the crankshaft, taking care to keep all parts clean from contamination. Reinstallation requires aligning and pressing the gear onto the crankshaft shaft.
Caterpillar cat 322 c fm excavator (prefix lar) service repair manual (lar000...ujjfkskeksmem
This document provides instructions for installing and removing the crankshaft main bearings on a Caterpillar 3126B engine. It outlines the required tools and steps to install the upper and lower main bearing halves into the cylinder block and crankshaft main bearing caps. Technicians are instructed to check the crankshaft end play once installed using a dial indicator. The summary also includes removing the crankshaft, which must be done before removing the crankshaft gear.
Caterpillar cat 325 c mobile hyd power unit (prefix msg) service repair manua...f98soeodidkdk
The document provides instructions for removing and installing a crankshaft gear on a 3126B engine. It lists the required tools and steps to remove the crankshaft first before removing the gear using a bearing puller. The installation procedure is not described.
Caterpillar Cat 325C MOBILE HYD POWER UNIT (Prefix MSG) Service Repair Manual...yan77xunhao
This document provides instructions for installing a crankshaft in a 3126B engine used in a 325C Mobile Hydraulic Power Unit. The instructions include:
1) Cleaning the cylinder block bearing surfaces and applying oil to the upper main bearings.
2) Installing the lower crankshaft main bearing halves into the bearing caps and installing the caps onto the cylinder block.
3) Checking crankshaft end play with a dial indicator to ensure it is within specifications.
Caterpillar Cat 325C MOBILE HYD POWER UNIT (Prefix MSG) Service Repair Manual...jfkskmdmmdd
The document provides instructions for removing and installing a crankshaft gear on a 3126B engine. It lists the required tools and steps to remove the crankshaft first before removing the gear using a bearing puller. The installation procedure is not described.
Caterpillar Cat 325C MOBILE HYD POWER UNIT (Prefix MSG) Service Repair Manual...jfkskmmdmdm
This document provides instructions for installing a crankshaft in a 3126B engine used in a 325C Mobile Hydraulic Power Unit. The instructions include:
1) Cleaning the cylinder block bearing surfaces and applying oil to the upper main bearings.
2) Installing the lower crankshaft main bearing halves into the bearing caps and installing the caps onto the cylinder block.
3) Checking crankshaft end play with a dial indicator to ensure it is within specifications.
Caterpillar cat 325 c mobile hyd power unit (prefix msg) service repair manua...fjsjjekdkme
The document provides instructions for removing and installing a crankshaft gear on a 3126B engine. It lists the required tools and begins by instructing the user to first remove the crankshaft by following the procedure in another document. The removal procedure then instructs the user to use a bearing puller and hydraulic pump to pull the gear off the crankshaft. The installation procedure is not shown, but presumably provides instructions for pressing the gear back onto the crankshaft.
Caterpillar cat 320 d l excavator (prefix jfz) service repair manual (jfz0000...fjjsefkksemm
This document provides instructions for removing and installing various components of the flywheel and crankshaft area of a Caterpillar C6.4 engine, including the flywheel, flywheel housing, crankshaft rear seal, and crankshaft pulley. The procedures include using various specialty tools and taking precautions such as cleaning parts and applying retaining compounds. Detailed illustrations are provided to supplement the text instructions.
Caterpillar cat 320 d excavator (prefix jfz) service repair manual (jfz00001 ...fjjkekfksemmm
This document provides instructions for removing and installing various components of the flywheel and crankshaft area of a Caterpillar C6.4 engine, including the flywheel, flywheel housing, crankshaft rear seal, and crankshaft pulley. The procedures include using various specialty tools and taking precautions such as cleaning parts and applying retaining compounds. Detailed illustrations are provided to supplement the text instructions.
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...ze6074xunong
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...gongfuao7509
The document provides instructions for removing and installing the flywheel and crankshaft pulley on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing components like the flywheel, flywheel housing, and crankshaft rear seal. Instructions are provided for cleaning and preparing components, as well as torquing bolts to the specified values. The document aims to guide maintenance technicians in properly servicing these engine components.
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...yu5676962
The document provides instructions for removing and installing the flywheel and crankshaft pulley on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing components like the flywheel, flywheel housing, and crankshaft rear seal. Instructions are provided for cleaning and preparing components, as well as torquing bolts to the specified values. The document aims to guide maintenance technicians in properly servicing these engine components.
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...f8seodkdmdmed3
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, placing the housing back on the cylinder block, and securing it with bolts and washers.
Caterpillar Cat 320D L Excavator (Prefix JFZ) Service Repair Manual (JFZ00001...fusjekkdmdmd2w
The document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D excavator engine. It describes using various tools to remove components like the muffler, flywheel, flywheel bolts, and flywheel housing bolts. Detailed illustrations show each step, like installing a lifting bracket and bolts to remove the heavy flywheel. Cleaning and installing new gaskets is emphasized during reassembly.
The document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D excavator engine. It describes using various tools to remove components like the muffler, flywheel, flywheel bolts, and flywheel housing bolts. Detailed illustrations show each step, like installing a lifting bracket and bolts to remove the heavy flywheel. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new seal. The instructions cover engines with both a 14-bolt housing assembly and a 10-bolt housing assembly.
The document provides instructions for removing and installing camshaft bearings, engine oil pans, and piston cooling jets on a Caterpillar 3054C engine. It describes the required tools and parts, cleaning requirements, installation procedures including torque specifications, and references other documents for additional information.
This document provides instructions for removing and installing the front housing on a Caterpillar 3054 engine. It describes:
1) Removing bolts and the front housing, which contains gears and covers the camshaft.
2) Preparing and installing a new gasket and bolts to secure the front housing.
3) Ensuring proper alignment and torque specifications are followed for reinstallation.
This document provides instructions for removing and installing a steering cylinder on a 416D backhoe loader. It describes:
1. Removing the tie rods from the front axle. Removing the spanner nut and removing the steering cylinder assembly from the axle housing using a rubber mallet.
2. Disassembling the steering cylinder by removing retaining rings, seals, guides, and fittings.
3. Reassembling the steering cylinder by installing the parts in reverse order.
4. Installing the steering cylinder into the axle housing and installing the spanner nut and tie rods.
CASE IH WD1903 Self-Propelled Windrower Service Repair Manual (from PIN YCG66...jfksemmdm3e
This document is a service manual for Case IH self-propelled windrowers from PIN YCG667001 and above. It contains information on engine systems, front and rear axle systems, hydrostatic drive, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments and headers, and the platform, cab, bodywork and decals. The manual provides maintenance and repair instructions for qualified dealership personnel and warns that anyone performing repairs without following the procedures could be responsible for damages.
This document provides instructions for assembling a torque converter for a 730 Articulated Truck. It lists the required tools and parts and provides 43 steps and accompanying illustrations to assemble the torque converter. The steps include installing bearings, seals, gears, housings and other components. The final step is to connect the assembled torque converter housing to the planetary transmission.
John Deere 54, 60 and 72-Inch Mid Mount Mowers Service Repair Manual.pdfjfksemmdm3e
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two people.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a bearing pilot and puller plate tool, then installing new bearings with the same tool.
4) Removing the engine oil pan by draining oil, removing bolts and clips, then reinstalling and applying sealant in beads.
CASE IH WD2303 Self-Propelled Windrower Service Repair Manual (from PIN YCG66...jfksemmdm3e
This document is a service manual for Case IH self-propelled windrowers from PIN YCG667001 and above. It contains sections on the engine, front and rear axle systems, hydrostatic drive, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments/headers, and the platform, cab, bodywork, and decals. The introduction provides basic instructions for qualified dealership personnel on repair and maintenance work using the procedures in the manual.
This document provides instructions for removing and installing various components of a 3054C engine, including:
1) The crankshaft pulley, which is removed by taking out setscrews and the thrust block.
2) The crankshaft front seal, which is pulled out using a suitable puller to avoid damaging the housing.
3) The front cover, which is secured by setscrews and gasket and must be cleaned before installation.
This document provides assembly instructions for the transmission of a 416D Backhoe Loader. It includes notes on cleaning and preparation, lists required tools, and provides detailed step-by-step instructions and illustrations for assembling the transmission components in the following order: reverse shaft assembly, input shaft assembly, and shaft assembly. Precautions are given for lubrication, seals, and bearing installation temperatures.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and illustrations showing the removal and installation steps. The removal process involves using a lifting device to remove the flywheel and housing, while installation requires heating the flywheel ring gear and using a press and alignment tool to correctly position the rear seal and housing. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. Removal of the flywheel requires loosening bolts and using a lifting device due to its weight of 53 kg. Installation of the crankshaft rear seal involves cleaning, lubricating, and pressing the seal into place using the proper tool. Proper torque values are also provided for reinstalling components.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054C engine. It describes:
1. Removing the electric starting motor and flywheel first.
2. Using link brackets as required tools to support the flywheel housing during removal and installation.
3. Removing bolts to separate the flywheel housing from the engine, and installing new bolts to secure the housing during reinstallation.
More Related Content
Similar to Caterpillar Cat 322C FM EXCAVATOR (Prefix LAR) Service Repair Manual (LAR00001 and up).pdf
Caterpillar cat 320 d excavator (prefix jfz) service repair manual (jfz00001 ...fjjkekfksemmm
This document provides instructions for removing and installing various components of the flywheel and crankshaft area of a Caterpillar C6.4 engine, including the flywheel, flywheel housing, crankshaft rear seal, and crankshaft pulley. The procedures include using various specialty tools and taking precautions such as cleaning parts and applying retaining compounds. Detailed illustrations are provided to supplement the text instructions.
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...ze6074xunong
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...gongfuao7509
The document provides instructions for removing and installing the flywheel and crankshaft pulley on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing components like the flywheel, flywheel housing, and crankshaft rear seal. Instructions are provided for cleaning and preparing components, as well as torquing bolts to the specified values. The document aims to guide maintenance technicians in properly servicing these engine components.
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...yu5676962
The document provides instructions for removing and installing the flywheel and crankshaft pulley on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing components like the flywheel, flywheel housing, and crankshaft rear seal. Instructions are provided for cleaning and preparing components, as well as torquing bolts to the specified values. The document aims to guide maintenance technicians in properly servicing these engine components.
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...f8seodkdmdmed3
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, placing the housing back on the cylinder block, and securing it with bolts and washers.
Caterpillar Cat 320D L Excavator (Prefix JFZ) Service Repair Manual (JFZ00001...fusjekkdmdmd2w
The document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D excavator engine. It describes using various tools to remove components like the muffler, flywheel, flywheel bolts, and flywheel housing bolts. Detailed illustrations show each step, like installing a lifting bracket and bolts to remove the heavy flywheel. Cleaning and installing new gaskets is emphasized during reassembly.
The document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D excavator engine. It describes using various tools to remove components like the muffler, flywheel, flywheel bolts, and flywheel housing bolts. Detailed illustrations show each step, like installing a lifting bracket and bolts to remove the heavy flywheel. Precautions are provided to keep parts clean and contain fluids.
Similar to Caterpillar Cat 322C FM EXCAVATOR (Prefix LAR) Service Repair Manual (LAR00001 and up).pdf (8)
This document provides instructions for removing and installing the crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new seal. The instructions cover engines with both a 14-bolt housing assembly and a 10-bolt housing assembly.
The document provides instructions for removing and installing camshaft bearings, engine oil pans, and piston cooling jets on a Caterpillar 3054C engine. It describes the required tools and parts, cleaning requirements, installation procedures including torque specifications, and references other documents for additional information.
This document provides instructions for removing and installing the front housing on a Caterpillar 3054 engine. It describes:
1) Removing bolts and the front housing, which contains gears and covers the camshaft.
2) Preparing and installing a new gasket and bolts to secure the front housing.
3) Ensuring proper alignment and torque specifications are followed for reinstallation.
This document provides instructions for removing and installing a steering cylinder on a 416D backhoe loader. It describes:
1. Removing the tie rods from the front axle. Removing the spanner nut and removing the steering cylinder assembly from the axle housing using a rubber mallet.
2. Disassembling the steering cylinder by removing retaining rings, seals, guides, and fittings.
3. Reassembling the steering cylinder by installing the parts in reverse order.
4. Installing the steering cylinder into the axle housing and installing the spanner nut and tie rods.
CASE IH WD1903 Self-Propelled Windrower Service Repair Manual (from PIN YCG66...jfksemmdm3e
This document is a service manual for Case IH self-propelled windrowers from PIN YCG667001 and above. It contains information on engine systems, front and rear axle systems, hydrostatic drive, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments and headers, and the platform, cab, bodywork and decals. The manual provides maintenance and repair instructions for qualified dealership personnel and warns that anyone performing repairs without following the procedures could be responsible for damages.
This document provides instructions for assembling a torque converter for a 730 Articulated Truck. It lists the required tools and parts and provides 43 steps and accompanying illustrations to assemble the torque converter. The steps include installing bearings, seals, gears, housings and other components. The final step is to connect the assembled torque converter housing to the planetary transmission.
John Deere 54, 60 and 72-Inch Mid Mount Mowers Service Repair Manual.pdfjfksemmdm3e
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two people.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a bearing pilot and puller plate tool, then installing new bearings with the same tool.
4) Removing the engine oil pan by draining oil, removing bolts and clips, then reinstalling and applying sealant in beads.
CASE IH WD2303 Self-Propelled Windrower Service Repair Manual (from PIN YCG66...jfksemmdm3e
This document is a service manual for Case IH self-propelled windrowers from PIN YCG667001 and above. It contains sections on the engine, front and rear axle systems, hydrostatic drive, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments/headers, and the platform, cab, bodywork, and decals. The introduction provides basic instructions for qualified dealership personnel on repair and maintenance work using the procedures in the manual.
This document provides instructions for removing and installing various components of a 3054C engine, including:
1) The crankshaft pulley, which is removed by taking out setscrews and the thrust block.
2) The crankshaft front seal, which is pulled out using a suitable puller to avoid damaging the housing.
3) The front cover, which is secured by setscrews and gasket and must be cleaned before installation.
This document provides assembly instructions for the transmission of a 416D Backhoe Loader. It includes notes on cleaning and preparation, lists required tools, and provides detailed step-by-step instructions and illustrations for assembling the transmission components in the following order: reverse shaft assembly, input shaft assembly, and shaft assembly. Precautions are given for lubrication, seals, and bearing installation temperatures.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and illustrations showing the removal and installation steps. The removal process involves using a lifting device to remove the flywheel and housing, while installation requires heating the flywheel ring gear and using a press and alignment tool to correctly position the rear seal and housing. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. Removal of the flywheel requires loosening bolts and using a lifting device due to its weight of 53 kg. Installation of the crankshaft rear seal involves cleaning, lubricating, and pressing the seal into place using the proper tool. Proper torque values are also provided for reinstalling components.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054C engine. It describes:
1. Removing the electric starting motor and flywheel first.
2. Using link brackets as required tools to support the flywheel housing during removal and installation.
3. Removing bolts to separate the flywheel housing from the engine, and installing new bolts to secure the housing during reinstallation.
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and gives step-by-step procedures for both removing and installing the seal. For engines with a 14-bolt housing, the instructions explain how to remove the housing, seal, and gasket before installing the new gasket and seal and reattaching the housing. For engines with a 10-bolt housing, the one-piece housing assembly is removed and installed as a unit.
The document provides instructions for removing and disassembling the valve mechanism cover, rocker shaft, and associated components of a Caterpillar C4.4 engine. It describes removing the valve mechanism cover and brackets. It then details using a tool to rotate the crankshaft and position the valves, loosening threaded inserts on the rocker arms, and removing the rocker shaft assembly and pushrods while marking their positions. Finally, it explains disassembling the rocker shaft assembly by removing screws, retaining clips, springs, and separating the rocker arm assemblies.
John Deere XUV 620i Gator Utility Vehicle Service Repair Manual.pdfjfksemmdm3e
This technical manual provides service and repair information for the John Deere Gator XUV 620i utility vehicle. The manual is organized into sections covering specifications, safety, components, operation, maintenance, and repairs. It is intended as a resource for experienced technicians working with this product. Safety notices and procedures are highlighted throughout to warn of hazards during service.
John Deere XUV 850D Gator Utility Vehicle Service Repair Manual (tm1737).pdfjfksemmdm3e
This technical manual provides service and repair information for the John Deere XUV 850D Gator utility vehicle. The manual is organized into sections covering specifications, safety, components, operation, diagnostics, and repairs. It aims to keep all information for a particular system together to aid technicians in servicing this vehicle. Safety is the first section and warns of dangers of fuel and working around heaters or other fire hazards.
This document provides instructions for removing and installing an engine in a 420F2 backhoe loader. It outlines 17 steps for removing the engine, which include disconnecting wiring harnesses, hoses, and other components. It then outlines 17 steps for installing the new engine, which involve connecting all the removed components in reverse order. Tools required include a hydraulic jack and load leveling beam to lift the heavy engine. Safety notices are provided to keep components clean and contain fluids.
The document provides instructions for removing and installing various components of the rear drive and steering axle assembly of a 420D backhoe loader, including:
- Removing the rear tires, drive shaft brackets, parking brake assembly, hydraulic hoses, manifold brackets, rear steer sensor wire, and axle mounting nuts and plates.
- Positioning a hydraulic jack under the axle and using a lifting device to remove the axle from the vehicle.
- Removing additional components from the axle including a parking brake bracket, cover, retaining clip, pin and washer.
The procedures include illustrations of each step and require tools such as a puller, wrench, heat gun and hydraulic jack. Safety notices
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C FM EXCAVATOR LAR
Configuration: 322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01518323
Crankshaft Main Bearings - Install
SMCS - 1203-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Main Bearing Tool 1
B 8T-5096 Dial Indicator Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Place clean engine oil on the crankshaft main bearings prior to assembly. Ensure that the
tabs on the back side of the crankshaft main bearings fit in the grooves of the crankshaft main
bearing caps and the cylinder block.
1/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00516920
1. Use Tool (A) and install the upper halves of the crankshaft main bearings in the cylinder
block. Do not put oil on the back of the crankshaft main bearing.
Illustration 2 g00610152
2. Install the lower halves of the crankshaft main bearings in crankshaft main bearing caps (2).
Do not put oil on the back of the crankshaft main bearing.
NOTICE
Crankshaft main bearing caps should be installed with the part
number toward the right side of the engine. Crankshaft main bearing
caps are to be identified by stamped numbers 1 through 7 located on
the bottom surface. The thrust plate is used on the number 6
crankshaft main bearing only.
3. Place crankshaft main bearing caps (2) in position on the cylinder block. Place clean engine
oil or Molylube on the bolt threads and on the washer face. Install bolts (1).
4. Tighten bolts (1) to a torque of 54 ± 7 N·m (40 ± 5 lb ft). Tighten each bolt (1) for an
additional 90 ± 5 degrees (1/4 turn).
2/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00517003
5. Check the end play of the crankshaft with Tool (B). The end play must be 0.07 mm
(0.003 inch) to 0.32 mm (0.013 inch).
End By:
a. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 2 22:08:51 UTC+0800 2019
3/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C FM EXCAVATOR LAR
Configuration: 322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02374826
Crankshaft - Remove
SMCS - 1202-011
Removal Procedure
Start By:
a. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
b. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
c. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 3. Put identification marks on the gear train for installation purposes. Attach a suitable lifting
device to each end of crankshaft (1). Carefully remove crankshaft (1) from the cylinder
block. The weight of crankshaft (1) is approximately 60 kg (132 lb).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 2 22:09:46 UTC+0800 2019
3/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C FM EXCAVATOR LAR
Configuration: 322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01931442
Crankshaft Wear Sleeve (Rear) - Remove - If Equipped
SMCS - 1161-011-ZV
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-4869 Distorter Ring 1
B 5P-7312 Seal Distorter 1
Start By:
a. Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear
Seal - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g00614029
Note: Wear sleeves are not installed at the factory. The wear sleeve is included with the
replacement rear seal.
1. Install Tooling (A) in the bore of the crankshaft rear sleeve.
2. Install Tooling (B) between Tooling (A) and the crankshaft wear sleeve. Turn Tooling (B)
until the edge of Tooling (B) makes a crease in the crankshaft wear sleeve. Make a crease in
the crankshaft wear sleeve at two other locations around the crankshaft wear sleeve until the
crankshaft wear sleeve is loose.
3. Remove Tooling (B), Tooling (A), and the crankshaft wear sleeve from the end of the
crankshaft.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 2 22:10:42 UTC+0800 2019
2/2
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C FM EXCAVATOR LAR
Configuration: 322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01929732
Crankshaft Wear Sleeve (Rear) - Install
SMCS - 1161-012-ZV
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C(1)
132-8772 Seal Locator 1
D(1)
1U-7596 Bolt 2
E(1)
1U-7597 Sleeve Ring 1
F(1)
1U-7594 Seal Installer 1
G(1)
9S-8858 Nut 1
(1)
Part of the 1U-7598 Seal Installer
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the rear of the crankshaft is thoroughly clean and dry prior to the installation of
the crankshaft rear seal.
1/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g01003875
2. Fasten Tooling (C) to the rear of the crankshaft with Tooling (D). Hand tighten Tooling (D).
3. Position the crankshaft rear seal and crankshaft rear sleeve (1) on Tooling (C). Position
Tooling (E) on Tooling (C).
Illustration 2 g01003866
Typical example
4. Position Tooling (F) over Tooling (C) and Tooling (E). Install Tooling (G). Tighten Tooling
(G) in order to install the crankshaft rear seal and the crankshaft wear sleeve.
5. Remove Tooling (G), Tooling (F), and Tooling (E). Turn over Tooling (E). Install Tooling
(E), Tooling (F), and Tooling (G). Tighten Tooling (G) in order to complete the installation
of the crankshaft rear seal and the crankshaft wear sleeve.
6. Remove Tooling (G) and Tooling (F). Check Tooling (E) and Tooling (C). The faces of
Tooling (E) and Tooling (C) will be flush if the crankshaft rear seal and the crankshaft wear
sleeve are properly installed. Refer to the Specifications module for more information.
7. Remove Tooling (E), Tool (E), and Tooling (C).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
2/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C FM EXCAVATOR LAR
Configuration: 322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02374834
Crankshaft - Install
SMCS - 1202-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-5096 Dial Indicator Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Ensure that the crankshaft main bearing tabs engage with the grooves
in the block and the crankshaft main bearing cap.
Note: The number six main bearing is the thrust bearing.
1. Clean the bearing surfaces in the cylinder block for the main bearings. Apply clean engine
oil on the upper main bearing. Do not put engine oil on the back side of the bearing
1/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. surfaces. Install the upper main bearing in the cylinder block. Ensure that the tab on the
back side of the bearing engages with the groove in the cylinder block.
Illustration 1 g01184978
2. Put clean engine oil on the journals of the crankshaft bearing. Attach a suitable lifting
device to crankshaft (1). The weight of crankshaft (1) is approximately 60 kg (132 lb).
Carefully install the crankshaft in the cylinder block.
3. Clean the bearing surface of the main bearing caps. Install the lower main bearing in the
crankshaft main bearing caps. Ensure that the tab on the back side of the bearing engages
with the groove in the main bearing cap. Apply clean engine oil on the lower main bearing.
Do not put engine oil on the back side of the bearing surfaces.
4. Install crankshaft main bearing caps with the part numbers toward the right hand side of the
cylinder block. The numbers should start at the front of the engine. Place clean engine oil or
Molylube on the bolt threads and the washers.
2/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01028042
5. Install the bolts for main bearing caps (2). Tighten the bolts to a torque of 54 ± 7 N·m
(40 ± 5 lb ft).
6. Turn the bolts for an additional 90 ± 5 degrees (1/4 turn).
7. Install connecting rod caps (3). Refer to Disassembly and Assembly, "Pistons and
Connecting Rods - Install".
8. Check the end play of crankshaft (1) with Tooling (A). The end play must be
0.07 to 0.32 mm (0.003 to 0.013 inch).
End By:
a. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
b. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
c. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 2 22:12:34 UTC+0800 2019
3/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C FM EXCAVATOR LAR
Configuration: 322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01984006
Crankshaft Gear - Remove and Install
SMCS - 1204-010-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8B-7551 Bearing Puller 1
8B-7549 Puller Leg 2
3H-0465 Push-Puller Plate 4
6B-6682 Full Nut 2
8B-7560 Step Plate 1
1P-0820 Hydraulic Puller 1
9U-6600 Hand Hydraulic Pump 1
Start By:
a. Remove the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00988783
1. Use Tooling (A) in order to remove crankshaft gear (3) from crankshaft (1).
2. Remove woodruff key (2).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g00988783
1. Position woodruff key (2) in crankshaft (1).
Hot oil and hot components can cause personal injury. Do not allow hot
oil or hot components to contact the skin.
2. Raise the temperature of crankshaft gear (3). Install crankshaft gear (3) on crankshaft (1).
End By:
a. Install the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 2 22:13:30 UTC+0800 2019
3/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C FM EXCAVATOR LAR
Configuration: 322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i05977048
Bearing Clearance - Check
SMCS - 1203-535; 1219-535
Measurement Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
198-9142
Plastic Gauge (Green)
0.025 to 0.076 mm
(0.001 to 0.003 inch)
1
198-9143
Plastic Gauge (Red)
0.051 to 0.152 mm
(0.002 to 0.006 inch)
1
198-9144
Plastic Gauge (Blue)
0.102 to 0.229 mm
(0.004 to 0.009 inch)
1
198-9145
Plastic Gauge (Yellow)
0.230 to 0.510 mm
(0.009 to 0.020 inch)
1
Note: Plastic gauge may not be necessary when the engine is in the chassis.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Note: Cat does not recommend the checking of the actual bearing clearances particularly on small
engines. This is because of the possibility of obtaining inaccurate results and the possibility of
damaging the bearing or the journal surfaces. Each Cat engine bearing is quality checked for
specific wall thickness.
Note: The measurements should be within specifications and the correct bearings should be used.
If the crankshaft journals and the bores for the block and the rods were measured during
disassembly, no further checks are necessary. However, if the technician still wants to measure the
bearing clearances, Tooling (A) is an acceptable method. Tooling (A) is less accurate on journals
with small diameters if clearances are less than 0.10 mm (0.004 inch).
NOTICE
Lead wire, shim stock or a dial bore gauge can damage the bearing
surfaces.
The technician must be very careful to use Tooling (A) correctly. The following points must be
remembered:
• Ensure that the backs of the bearings and the bores are clean and dry.
• Ensure that the bearing locking tabs are properly seated in the tab grooves.
• The crankshaft must be free of oil at the contact points of Tooling (A).
1. Put a piece of Tooling (A) on the crown of the bearing that is in the cap.
Note: Do not allow Tooling (A) to extend over the edge of the bearing.
2. Use the correct torque-turn specifications in order to install the bearing cap. Do not use an
impact wrench. Be careful not to dislodge the bearing when the cap is installed.
Note: Do not turn the crankshaft when Tooling (A) is installed.
3. Carefully remove the cap, but do not remove Tooling (A). Measure the width of Tooling
(A) while Tooling (A) is in the bearing cap or on the crankshaft journal. Refer to Illustration
1.
2/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Illustration 1 g01152855
Typical Example
4. Remove all of Tooling (A) before you install the bearing cap.
Note: When Tooling (A) is used, the readings can sometimes be unclear. For example, all
parts of Tooling (A) are not the same width. Measure the major width in order to ensure that
the parts are within the specification range. Refer to Specifications Manual, "Connecting
Rod Bearing Journal" and Specifications Manual, "Main Bearing Journal" for the correct
clearances.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 2 22:14:25 UTC+0800 2019
3/3
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C FM EXCAVATOR LAR
Configuration: 322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01984226
Idler Pulley - Remove and Install
SMCS - 1358-010
Illustration 1 g01028295
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 2 22:15:21 UTC+0800 2019
1/1
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C FM EXCAVATOR LAR
Configuration: 322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01930316
Belt Tensioner - Remove and Install
SMCS - 1358-010
Removal Procedure
Illustration 1 g01011962
1. Use a breaker bar to release the tension on belt tensioner (1). Remove the drive belt.
2. Remove bolt (2) and belt tensioner (1).
Installation Procedure
1/2
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 2 g01011962
1. Position belt tensioner (1) on the cylinder block. Install bolt (2).
2. Install the drive belt. Use a breaker bar to release tension on belt tensioner (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 2 22:16:17 UTC+0800 2019
2/2
322C Forest Swing Machines LAR00001-UP (MACHINE) POWERED BY 3126B En...
2019/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...