This document provides instructions for installing a heating and air conditioning unit on a 321C EXCAVATOR. It describes 14 steps for installing various components of the unit like hoses, bolts, ducts, covers and connecting harnesses. Safety precautions are provided to avoid injury from refrigerant and proper use of recovery and recycling equipment is advised when working on air conditioning systems. Separate sections provide instructions for removing and installing the blower motor and refrigerant receiver-dryer.
Caterpillar cat 321 c excavator (prefix kcr) service repair manual (kcr00001 ...ufjjskekkmde
This document provides instructions for removing and installing various components of the heating and air conditioning system on a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent and front/rear vents
It includes detailed illustrations and step-by-step instructions for each component, as well as safety warnings about working with refrigerants. Personal protective equipment and proper refrigerant handling techniques are emphasized throughout.
Caterpillar cat 321 d lcr excavator (prefix txa) service repair manual (txa00...ufdjjsekkmdme
This document provides instructions for removing and installing fuel injection lines and other fuel system components on a Caterpillar 321D LCR excavator. The removal procedure includes disconnecting fuel lines, removing mounting hardware, and using protective tools and plugs to prevent fluid loss and contamination. Installation is the reverse of removal, including installing new fuel lines, fittings, and hoses, and verifying fuel system pressure is purged before startup.
Caterpillar cat 321 d lcr excavator (prefix mpg) service repair manual (mpg00...ufdjjsekkmdme
1. The document provides instructions for removing and installing an electronic unit injector, turbocharger, and exhaust manifold on a Caterpillar 321D LCR excavator.
2. The electronic unit injector removal procedure involves disconnecting harness assemblies and fuel lines before using a pry bar to remove the injector. Proper identification of parts is important.
3. Turbocharger removal requires disconnecting tubes, hoses and nuts before the turbocharger can be lifted off. Individual turbocharger components like the turbine housing and compressor housing are also removable.
4. Exhaust manifold removal is dependent on first removing the turbocharger. Cleanliness is emphasized throughout the procedures.
The document provides instructions for removing and installing the fuel ratio control and fuel shutoff solenoid on a Caterpillar 3306 engine. It details the removal and installation procedures in steps with illustrations. The procedures involve disconnecting lines, removing mounting bolts and nuts, cleaning parts, applying thread lock, and reinstalling in the reverse order. Special tools and safety precautions are noted to properly complete the tasks.
Caterpillar cat 272 d xhp skid steer loader (prefix shy) service repair manua...ufjjsjekdkemme
The document provides instructions for removing and installing various components of a Caterpillar 272D XHP Skid Steer Loader engine, including:
- Removing and installing the fuel injection pump by disconnecting fuel lines, removing mounting nuts and gears, and reinstalling in reverse order.
- Removing and installing electronic unit injectors by removing overflow pipes and clamps, using a pry bar to remove injectors, and reinstalling seals and components.
- Removing and installing the turbocharger by removing nuts and bolts, disconnecting hoses and tubes, and reinstalling with anti-seize on bolts and nuts.
- Removing and installing the mass air flow pressure sensor by
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3304 engine, including:
- The fuel priming pump, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel transfer pump, which is removed by disconnecting fuel lines and removing mounting bolts. Disassembly and assembly instructions are also provided.
Caterpillar cat 320 e lrr excavator (prefix tfx) service repair manual (tfx00...fujdfjjkskekme
The document provides instructions for removing and installing a flywheel on a Caterpillar 320E LRR excavator. It describes in detail:
1. The tools needed and safety precautions to take before removing the flywheel. The removal process involves removing bolts and using guide studs to lift the flywheel off the engine.
2. Inspecting the flywheel and removing the ring gear if needed by heating it and pounding it off with a punch and hammer.
3. The installation process which reverses the removal steps and includes heating and pressing the ring gear back on if replaced and torquing the bolts to the specified value.
4. Similar level of detail is provided for
Caterpillar cat 432 d backhoe loader (prefix wep) service repair manual (wep0...ujfdjjskkemme
This document provides instructions for removing and installing the engine oil cooler and water pump on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new seals and gaskets. Safety notices are included to wear protective equipment and contain fluids during disassembly and reassembly.
Caterpillar cat 321 c excavator (prefix kcr) service repair manual (kcr00001 ...ufjjskekkmde
This document provides instructions for removing and installing various components of the heating and air conditioning system on a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent and front/rear vents
It includes detailed illustrations and step-by-step instructions for each component, as well as safety warnings about working with refrigerants. Personal protective equipment and proper refrigerant handling techniques are emphasized throughout.
Caterpillar cat 321 d lcr excavator (prefix txa) service repair manual (txa00...ufdjjsekkmdme
This document provides instructions for removing and installing fuel injection lines and other fuel system components on a Caterpillar 321D LCR excavator. The removal procedure includes disconnecting fuel lines, removing mounting hardware, and using protective tools and plugs to prevent fluid loss and contamination. Installation is the reverse of removal, including installing new fuel lines, fittings, and hoses, and verifying fuel system pressure is purged before startup.
Caterpillar cat 321 d lcr excavator (prefix mpg) service repair manual (mpg00...ufdjjsekkmdme
1. The document provides instructions for removing and installing an electronic unit injector, turbocharger, and exhaust manifold on a Caterpillar 321D LCR excavator.
2. The electronic unit injector removal procedure involves disconnecting harness assemblies and fuel lines before using a pry bar to remove the injector. Proper identification of parts is important.
3. Turbocharger removal requires disconnecting tubes, hoses and nuts before the turbocharger can be lifted off. Individual turbocharger components like the turbine housing and compressor housing are also removable.
4. Exhaust manifold removal is dependent on first removing the turbocharger. Cleanliness is emphasized throughout the procedures.
The document provides instructions for removing and installing the fuel ratio control and fuel shutoff solenoid on a Caterpillar 3306 engine. It details the removal and installation procedures in steps with illustrations. The procedures involve disconnecting lines, removing mounting bolts and nuts, cleaning parts, applying thread lock, and reinstalling in the reverse order. Special tools and safety precautions are noted to properly complete the tasks.
Caterpillar cat 272 d xhp skid steer loader (prefix shy) service repair manua...ufjjsjekdkemme
The document provides instructions for removing and installing various components of a Caterpillar 272D XHP Skid Steer Loader engine, including:
- Removing and installing the fuel injection pump by disconnecting fuel lines, removing mounting nuts and gears, and reinstalling in reverse order.
- Removing and installing electronic unit injectors by removing overflow pipes and clamps, using a pry bar to remove injectors, and reinstalling seals and components.
- Removing and installing the turbocharger by removing nuts and bolts, disconnecting hoses and tubes, and reinstalling with anti-seize on bolts and nuts.
- Removing and installing the mass air flow pressure sensor by
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3304 engine, including:
- The fuel priming pump, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel transfer pump, which is removed by disconnecting fuel lines and removing mounting bolts. Disassembly and assembly instructions are also provided.
Caterpillar cat 320 e lrr excavator (prefix tfx) service repair manual (tfx00...fujdfjjkskekme
The document provides instructions for removing and installing a flywheel on a Caterpillar 320E LRR excavator. It describes in detail:
1. The tools needed and safety precautions to take before removing the flywheel. The removal process involves removing bolts and using guide studs to lift the flywheel off the engine.
2. Inspecting the flywheel and removing the ring gear if needed by heating it and pounding it off with a punch and hammer.
3. The installation process which reverses the removal steps and includes heating and pressing the ring gear back on if replaced and torquing the bolts to the specified value.
4. Similar level of detail is provided for
Caterpillar cat 432 d backhoe loader (prefix wep) service repair manual (wep0...ujfdjjskkemme
This document provides instructions for removing and installing the engine oil cooler and water pump on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new seals and gaskets. Safety notices are included to wear protective equipment and contain fluids during disassembly and reassembly.
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It includes detailed illustrations and numbered steps for each procedure, and safety warnings regarding working with refrigerants.
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It includes detailed illustrations and numbered steps for each procedure, and safety warnings regarding working with refrigerants.
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It describes each component and provides illustrated step-by-step instructions for removal and installation, noting safety precautions when working with refrigerants.
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It includes detailed illustrations and numbered steps for each procedure, and safety warnings regarding working with refrigerants.
This document provides instructions for installing and removing components of an air conditioning system on a 321C EXCAVATOR model. It describes removing and installing a blower motor and refrigerant receiver-dryer. Safety precautions are provided, including warnings about working with refrigerant and proper use of recovery and recycling equipment when removing refrigerant. Diagrams show the component locations and parts involved in the procedures.
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It describes each component and provides illustrated step-by-step instructions for removal and installation, noting safety precautions when working with refrigerants.
This document provides instructions for removing and installing various components of the heating and air conditioning system on a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It describes each component and provides illustrated step-by-step instructions for removal and installation, noting safety precautions when working with refrigerants.
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It includes detailed illustrations and numbered steps for each procedure, and safety warnings regarding working with refrigerants.
This document provides instructions for installing and removing components of an air conditioning system on a 321C EXCAVATOR model. It describes removing and installing a blower motor and refrigerant receiver-dryer. Safety precautions are provided, including warnings about working with refrigerant and proper use of recovery and recycling equipment when removing refrigerant. Diagrams show the component locations and parts involved in the procedures.
The document provides installation instructions for a pressure switch on an excavator's air conditioning system. It details 30 steps for installing various components like the evaporator coil, temperature sensor, tubes, motors, and wiring harnesses. Proper handling of refrigerant during the process is emphasized for safety.
The document provides installation and removal instructions for components of the heating and air conditioning system on a 320C excavator. It describes in detail how to remove and install components like the evaporator coil, temperature sensor, pressure switch, and control panel. The procedures include illustrations showing the component locations and steps to disconnect wiring harnesses, remove mounting hardware, and position insulation.
The document provides installation and removal instructions for components of the air conditioning system in a 320C excavator. It describes in detail how to remove and install parts like the evaporator coil, temperature sensor, pressure switch, and control panel. The procedures include illustrations and numbered steps for each component. The overall document provides technical service manual details for working on the excavator's air conditioning system.
The document provides installation and removal instructions for components of the air conditioning system of a 320C excavator. It describes in detail how to remove and install parts like the evaporator coil, temperature sensor, pressure switch, and control panel. The procedures include disconnecting wiring harnesses, removing mounting hardware and brackets, and ensuring proper installation of gaskets and seals. The goal is to properly service the air conditioning system while following safety protocols for working with refrigerants.
The document provides installation instructions for a pressure switch on an excavator's air conditioning system. It details 30 steps for installing various components like the evaporator coil, temperature sensor, tubes, motors, and wiring harnesses. Proper handling of refrigerant during installation is emphasized for safety.
The document provides installation and removal instructions for components of the heating and air conditioning system on a 320C excavator. It describes in detail how to remove and install components like the evaporator coil, temperature sensor, pressure switch, and control panel. The procedures include illustrations and step-by-step instructions to correctly remove parts, install new seals and components, and reconnect wiring harnesses. Cautions are provided regarding working with refrigerants and following regulations to properly recover refrigerant from the system.
The document provides installation instructions for a pressure switch on an excavator air conditioning system. It outlines 30 steps to correctly install insulation, coils, tubes, sensors, motors and other components. The summary ends by instructing technicians to install the heating and air conditioning unit once all internal components are in place.
The document provides installation instructions for a pressure switch on an excavator air conditioning system. It outlines 30 steps to correctly install insulation, coils, tubes, sensors, motors and other components. The summary ends by instructing technicians to install the heating and air conditioning unit once all internal components are in place.
Yamaha g2 a golf cart service repair manualjjskefkskemik
This document is a Yamaha service manual that provides information on servicing Yamaha G2-A and G2-E vehicles. It contains chapters covering general information, specifications, periodic inspection and adjustment procedures, engine overhaul, carburetion, power train, chassis, electrical systems, troubleshooting, and more. Special tools are listed for tasks like tune ups, engine service, power train service, chassis service, and electrical component maintenance. The manual provides detailed instructions and specifications to guide technicians in properly servicing and repairing Yamaha G2 vehicles.
Yale c875 gdp25 vxp lift truck service repair manualjjskefkskemik
The document provides service manual contents and procedures for removing an operator cab from various lift truck models. It contains the following key points:
- The operator cab is a separate unit that can be removed as a complete module from the frame.
- Steps include tilting the steering column, sliding the seat forward, disconnecting battery cables and air filter hoses, draining coolant by removing the radiator cap, and disconnecting heater hoses from the engine.
- Additional steps apply for models with air conditioning, which require extracting refrigerant from the AC system and disconnecting refrigerant lines.
- Removing the cab doors requires two people. Proper safety precautions are outlined when working on cooling
Yale b875 gp040 vx lift truck service repair manualjjskefkskemik
This service manual section provides descriptions and removal/installation procedures for components on the frame of certain lift truck models, including:
- The counterweight, hood, overhead guard, engine, cooling system, and exhaust system.
- Checks for the operator restraint system and procedures for repairing tanks and installing safety labels.
- Removal of the floor plate, side covers, hood, and other body parts to access components under the hood like the engine and transmission.
- Cautions are provided when putting the lift truck on blocks to maintain stability during repairs. Part numbers, component diagrams, and fastener locations are included.
Yale b875 gdp20 vx lift truck service repair manualjjskefkskemik
This document provides a service manual for GLP/GDP20VX, GLP/GDP25VX, GLP/GDP30VX, GLP/GDP35VX lift trucks. It contains sections on frame components, engine repair, transmissions, axles, hydraulics, electrical systems, and more. The frame includes the counterweight, fuel tank, hydraulic tank, and mounts for the overhead guard, hood, and cowl. Procedures are provided for removing and replacing components like the counterweight, hood, floor plates and side covers to access parts. Safety precautions are noted for when putting the truck on blocks for maintenance.
Yale (d875) gp040 vx lift truck service repair manualjjskefkskemik
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column up, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator covers, and draining coolant lines.
3. For models with air conditioning, extracting refrigerant and disconnecting AC lines.
4. Disconnecting wiring harnesses, heater lines, gas springs and removing door assemblies. The cab can then be lifted off as a complete unit.
More Related Content
Similar to Caterpillar cat 321 c excavator (prefix kcr) service repair manual (kcr00001 and up)
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It includes detailed illustrations and numbered steps for each procedure, and safety warnings regarding working with refrigerants.
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It includes detailed illustrations and numbered steps for each procedure, and safety warnings regarding working with refrigerants.
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It describes each component and provides illustrated step-by-step instructions for removal and installation, noting safety precautions when working with refrigerants.
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It includes detailed illustrations and numbered steps for each procedure, and safety warnings regarding working with refrigerants.
This document provides instructions for installing and removing components of an air conditioning system on a 321C EXCAVATOR model. It describes removing and installing a blower motor and refrigerant receiver-dryer. Safety precautions are provided, including warnings about working with refrigerant and proper use of recovery and recycling equipment when removing refrigerant. Diagrams show the component locations and parts involved in the procedures.
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It describes each component and provides illustrated step-by-step instructions for removal and installation, noting safety precautions when working with refrigerants.
This document provides instructions for removing and installing various components of the heating and air conditioning system on a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It describes each component and provides illustrated step-by-step instructions for removal and installation, noting safety precautions when working with refrigerants.
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It includes detailed illustrations and numbered steps for each procedure, and safety warnings regarding working with refrigerants.
This document provides instructions for installing and removing components of an air conditioning system on a 321C EXCAVATOR model. It describes removing and installing a blower motor and refrigerant receiver-dryer. Safety precautions are provided, including warnings about working with refrigerant and proper use of recovery and recycling equipment when removing refrigerant. Diagrams show the component locations and parts involved in the procedures.
The document provides installation instructions for a pressure switch on an excavator's air conditioning system. It details 30 steps for installing various components like the evaporator coil, temperature sensor, tubes, motors, and wiring harnesses. Proper handling of refrigerant during the process is emphasized for safety.
The document provides installation and removal instructions for components of the heating and air conditioning system on a 320C excavator. It describes in detail how to remove and install components like the evaporator coil, temperature sensor, pressure switch, and control panel. The procedures include illustrations showing the component locations and steps to disconnect wiring harnesses, remove mounting hardware, and position insulation.
The document provides installation and removal instructions for components of the air conditioning system in a 320C excavator. It describes in detail how to remove and install parts like the evaporator coil, temperature sensor, pressure switch, and control panel. The procedures include illustrations and numbered steps for each component. The overall document provides technical service manual details for working on the excavator's air conditioning system.
The document provides installation and removal instructions for components of the air conditioning system of a 320C excavator. It describes in detail how to remove and install parts like the evaporator coil, temperature sensor, pressure switch, and control panel. The procedures include disconnecting wiring harnesses, removing mounting hardware and brackets, and ensuring proper installation of gaskets and seals. The goal is to properly service the air conditioning system while following safety protocols for working with refrigerants.
The document provides installation instructions for a pressure switch on an excavator's air conditioning system. It details 30 steps for installing various components like the evaporator coil, temperature sensor, tubes, motors, and wiring harnesses. Proper handling of refrigerant during installation is emphasized for safety.
The document provides installation and removal instructions for components of the heating and air conditioning system on a 320C excavator. It describes in detail how to remove and install components like the evaporator coil, temperature sensor, pressure switch, and control panel. The procedures include illustrations and step-by-step instructions to correctly remove parts, install new seals and components, and reconnect wiring harnesses. Cautions are provided regarding working with refrigerants and following regulations to properly recover refrigerant from the system.
The document provides installation instructions for a pressure switch on an excavator air conditioning system. It outlines 30 steps to correctly install insulation, coils, tubes, sensors, motors and other components. The summary ends by instructing technicians to install the heating and air conditioning unit once all internal components are in place.
The document provides installation instructions for a pressure switch on an excavator air conditioning system. It outlines 30 steps to correctly install insulation, coils, tubes, sensors, motors and other components. The summary ends by instructing technicians to install the heating and air conditioning unit once all internal components are in place.
Similar to Caterpillar cat 321 c excavator (prefix kcr) service repair manual (kcr00001 and up) (17)
Yamaha g2 a golf cart service repair manualjjskefkskemik
This document is a Yamaha service manual that provides information on servicing Yamaha G2-A and G2-E vehicles. It contains chapters covering general information, specifications, periodic inspection and adjustment procedures, engine overhaul, carburetion, power train, chassis, electrical systems, troubleshooting, and more. Special tools are listed for tasks like tune ups, engine service, power train service, chassis service, and electrical component maintenance. The manual provides detailed instructions and specifications to guide technicians in properly servicing and repairing Yamaha G2 vehicles.
Yale c875 gdp25 vxp lift truck service repair manualjjskefkskemik
The document provides service manual contents and procedures for removing an operator cab from various lift truck models. It contains the following key points:
- The operator cab is a separate unit that can be removed as a complete module from the frame.
- Steps include tilting the steering column, sliding the seat forward, disconnecting battery cables and air filter hoses, draining coolant by removing the radiator cap, and disconnecting heater hoses from the engine.
- Additional steps apply for models with air conditioning, which require extracting refrigerant from the AC system and disconnecting refrigerant lines.
- Removing the cab doors requires two people. Proper safety precautions are outlined when working on cooling
Yale b875 gp040 vx lift truck service repair manualjjskefkskemik
This service manual section provides descriptions and removal/installation procedures for components on the frame of certain lift truck models, including:
- The counterweight, hood, overhead guard, engine, cooling system, and exhaust system.
- Checks for the operator restraint system and procedures for repairing tanks and installing safety labels.
- Removal of the floor plate, side covers, hood, and other body parts to access components under the hood like the engine and transmission.
- Cautions are provided when putting the lift truck on blocks to maintain stability during repairs. Part numbers, component diagrams, and fastener locations are included.
Yale b875 gdp20 vx lift truck service repair manualjjskefkskemik
This document provides a service manual for GLP/GDP20VX, GLP/GDP25VX, GLP/GDP30VX, GLP/GDP35VX lift trucks. It contains sections on frame components, engine repair, transmissions, axles, hydraulics, electrical systems, and more. The frame includes the counterweight, fuel tank, hydraulic tank, and mounts for the overhead guard, hood, and cowl. Procedures are provided for removing and replacing components like the counterweight, hood, floor plates and side covers to access parts. Safety precautions are noted for when putting the truck on blocks for maintenance.
Yale (d875) gp040 vx lift truck service repair manualjjskefkskemik
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column up, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator covers, and draining coolant lines.
3. For models with air conditioning, extracting refrigerant and disconnecting AC lines.
4. Disconnecting wiring harnesses, heater lines, gas springs and removing door assemblies. The cab can then be lifted off as a complete unit.
Yale (c875) gtp40 vx lift truck service repair manualjjskefkskemik
The document provides instructions for removing an operator cab from various lift truck models. Key steps include:
1. Tilting the steering column, sliding the seat forward, and opening doors/windows to access components.
2. Disconnecting the air filter hose, radiator cap, and heater hoses from the engine.
3. For models with air conditioning, extracting refrigerant from the system and disconnecting AC lines.
4. Removing fasteners to separate the cab from the lift truck frame. The cab can then be removed as a complete unit for replacement or repair.
Yale (b910) glc060 vx lift truck service repair manualjjskefkskemik
This service manual provides information on servicing and repairing various models of GC/GLC lift trucks. The document outlines procedures for removing and installing components like the counterweight, hood, overhead guard, engine, transmission, and covers. It contains sections on the frame description, removing the hood and seat, and replacing side covers. Safety warnings are provided, and diagrams show the locations of parts. Repair sections cover topics such as the cooling system, fuel systems, mast, cylinders, and electrical systems.
Yale (a985) erp100 vm lift truck service repair manualjjskefkskemik
This document provides a service manual for ERP080-1000VM (A985) that contains:
1. Sections covering various parts of the lift truck organized by part number, including the frame, operator's cab, AC motor repair, and more.
2. Descriptions and service procedures for parts of the frame including the counterweight assembly, overhead guard, and labels.
3. Information on the location of controllers and contactors for different lift truck models.
4. Warnings and procedures for discharging capacitors before working on electrical systems.
5. Details on an optional rapid charge system that some models may be equipped with.
Yale (a976) erp60 vl lift truck service repair manualjjskefkskemik
This document provides a service manual for lift truck model ERP040-070VL (A976). It contains sections covering various parts of the lift truck including the frame, operator's cab, AC motor, drive unit assembly, steering components, hydraulic system, electrical system, batteries, mast, and fasteners. The document describes the components that are located in the frame such as the counterweight, controllers, and Vehicle Systems Manager. It provides instructions for removing covers and plates to access components for service.
Perkins 2300 series 2306 c e14 6 cylinder turbocharged diesel engine service ...jjskefkskemik
This document provides a workshop manual for Perkins 2300 Series diesel engines, including models 2306A-E14 and 2306C-E14. It contains specifications, repair and maintenance instructions across 16 chapters covering the engine systems. The manual is intended to assist technicians in servicing and repairing these engine models. It includes detailed instructions, specifications, and torque values for disassembling, overhauling, and reassembling the engine components.
Perkins 400 series 402 d 403d 404d industrial engine (model gj) service repai...jjskefkskemik
This document provides instructions for disassembling and assembling various components of 402D-05, 403D-07, 403D-11, 403D-15, 403D-15T, 403D-17, 404D-15, 404D-22, 404D-22T, and 404D-22TA industrial engine models. The document covers procedures such as removing and installing the fuel filter base, fuel transfer pump, fuel lines, and other fuel system components, as well as servicing cooling system, valve train, cylinder head, crankshaft, and electrical parts. Safety warnings are provided throughout regarding hazards and preventing contamination.
New holland mh5.6 wheel excavator service repair manualjjskefkskemik
This document provides safety instructions for operating and servicing a hydraulic excavator. It emphasizes the importance of following all safety precautions to avoid risks and ensure personal safety. Specific safety topics covered include personal protective equipment, machine inspections, working from the operator's seat, travel safety, maintenance procedures, and waste disposal. Anyone performing service work must strictly follow the manufacturer's instructions using recommended tools, or they will be responsible for any damages resulting from improper repairs.
Kubota front loader service repair manualjjskefkskemik
This document provides a workshop manual for tractors, rotary mowers, and front loaders. It contains sections on identification, precautions, lubricants, tightening torques, maintenance checklists, special tools, tires, and implement limitations. The precautions section emphasizes safely handling electrical parts and wiring, including disconnecting negative battery terminals first, securely clamping wiring, avoiding damage, and checking for loose connections annually.
Komatsu wa430 5 wheel loader service repair manual sn60001 and upjjskefkskemik
This shop manual provides instructions for servicing a WA430-5 machine. It begins with safety precautions for technicians working on the machine. The manual contains sections on machine structure and function, testing and adjusting procedures, disassembly and assembly instructions, and maintenance standards. It also includes hydraulic and electrical diagrams. The WA430-5 is equipped with an SAA6D125E-3 engine, which is covered in its own engine manual. Technicians should consult both manuals as well as their local Komatsu distributor for any necessary parts to safely and effectively service the WA430-5.
Komatsu wa380 6 wheel loader service repair manual sn a54001 and upjjskefkskemik
This document is a shop manual for the WA380-6 wheel loader that provides instructions for maintenance, repair, and servicing of the vehicle. It contains sections on general information, vehicle structure and maintenance standards, specifications, testing and adjusting procedures, troubleshooting, disassembly and assembly, and diagrams. The manual is intended to help technicians correctly repair and service the vehicle. It is the property of Komatsu and may not be reproduced without authorization. Komatsu reserves the right to update the manual and make improvements to the vehicle without providing notice. Customers should contact their distributor for the latest revision of the manual.
Kioti daedong dk801 tractor service repair manualjjskefkskemik
This workshop manual provides service information for KIOTI tractors models DK651/751/801/901. The manual is divided into sections on mechanism, servicing, and safety procedures. It contains specifications, maintenance checklists, lubrication charts, and troubleshooting guides to aid servicing personnel in repairing and maintaining the tractors. Safety warnings are provided throughout and on decals installed on the tractors.
Jcb vm132 d smooth drum roller service repair manualjjskefkskemik
This document provides information about service tools and consumables for servicing JCB machines. It includes a list of common sealing and retaining compounds with their part numbers and intended uses. Torque specifications are also included for fasteners and hydraulic connections on the machines. The document is intended to aid JCB service engineers in maintaining and repairing hydraulic earthmoving equipment.
Jcb hm range medium and large hydraulic breakers service repair manual sn1095...jjskefkskemik
The document provides instructions for servicing JCB HM Range Medium and Large Hydraulic Breakers. It contains safety warnings and outlines the proper procedures for disassembling parts like the accumulator and piston. Tools required are listed, along with exploded part diagrams and specifications. The multi-page manual instructs technicians how to correctly maintain and repair the hydraulic breakers.
Ford 5640 tractor service repair manualjjskefkskemik
This document provides a shop manual for Ford tractor models 5640-6640-7740-7840-8240-8340. It contains instructions for servicing various components of the tractors, including the front axle assembly, steering linkage, brakes, clutch, cooling system, diesel fuel system, transmission, hydraulic and electrical systems. The manual includes an index, condensed service data with specifications, and diagrams.
Fendt 711 vario tractor service repair manualjjskefkskemik
The document provides safety instructions for working on and repairing the hydraulic system in Fendt tractors. It warns that the pressure pipes and accumulators connected to the central control block are pressurized up to 200 bar even with the engine off. The pressure must be manually relieved before performing any repairs in this area. Special care is required as the "Lock suspension / lower suspension" command does not relieve the pressure.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 321C EXCAVATOR KCR
Configuration: 321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
321C LCR Excavator Machine Systems
Media Number -RENR7108-03 Publication Date -01/04/2006 Date Updated -24/10/2018
i01861335
Heating and Air Conditioning Unit - Install
SMCS - 7304-012; 7309-012; 7320-012
Installation Procedure
Personal injury can result from contact with refrigerant.
Contact with refrigerant can cause frost bite. Keep face and hands away
to help prevent injury.
Protective goggles must always be worn when refrigerant lines are
opened, even if the gauges indicate the system is empty of refrigerant.
Always use precaution when a fitting is removed. Slowly loosen the
fitting. If the system is still under pressure, release it slowly in a well
ventilated area.
Personal injury or death can result from inhaling refrigerant through a
lit cigarette.
Inhaling air conditioner refrigerant gas through a lit cigarette or other
smoking method or inhaling fumes released from a flame contacting air
conditioner refrigerant gas, can cause bodily harm or death.
Do not smoke when servicing air conditioners or wherever refrigerant
gas may be present.
Use a certified recovery and recycling cart to properly remove the
refrigerant from the air conditioning system.
1/6321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00948849
1. Position the heating and air conditioning unit. Install bolt (27) and connect two hoses (26).
Tighten two hose clamps (25).
Illustration 2 g00948846
2. Install bolts (24), (23), and (22). Tighten bolt (22) to a torque of 3.85 � 0.65 N�m
(2.84 � 0.479 lb ft). Tighten bolt (23) to a torque of 9.35 � 1.45 N�m (6.90 � 1.070 lb ft).
Illustration 3 g00948845
3. Position mount (21) for the relays. Install bolts (19). Connect six harness assemblies (20).
2/6321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00948827
4. Use two people and position support assembly (18). The weight of support assembly (18) is
approximately 24 kg (52 lb). Install assembly (17) for the air distribution system.
Illustration 5 g00948820
5. Install duct (16) and bolt (15).
3/6321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g00948809
6. Install duct (14) and bolts (13). Install vents (12).
Illustration 7 g00948655
7. Install bolts (11) and duct (10).
Illustration 8 g00948649
8. Install panel (9) and five screws (8).
Illustration 9 g00948647
4/6321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 9. Install cover (6) and bolts (7).
Illustration 10 g00948642
10. Connect nine harness assemblies (5).
Illustration 11 g00948631
Left rear
Illustration 12 g00948629
Right rear
5/6321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 13 g00948628
11. Install bolts (4).
Illustration 14 g00948489
12. Roll floormat (2) backward and position plate (3). Install bolts (1).
13. Charge the air conditioner system. The correct charge is 0.9979 kg (2.2 lb). Refer to Service
Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for
the procedure. Refer to Special Publication, NEDG5065, "Air Conditioning Tools" for the
tools.
14. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual,
"Capacities (Refill)" for the proper amount of coolant. Refer to Operation and Maintenance
Manual, "Lubricant Viscosities" for the proper type of coolant.
End By:
a. Install the seat support. Refer to Disassembly and Assembly, "Seat Support - Remove and
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 3 18:40:32 UTC+0800 2019
6/6321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 321C EXCAVATOR KCR
Configuration: 321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
321C LCR Excavator Machine Systems
Media Number -RENR7108-03 Publication Date -01/04/2006 Date Updated -24/10/2018
i02532897
Blower Motor (Air Conditioner, Heater) - Remove and Install
SMCS - 7304-010-BW; 7309-010-BW; 7320-010-BW
Removal Procedure
Start By:
A. Remove the heating and air conditioning unit. Refer to Disassembly and Assembly,
"Heating and Air Conditioning Unit - Remove".
Illustration 1 g00949152
1. Remove screws (1) and cover (2) . Remove air filter (3) .
1/5321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g00949153
2. Disconnect hose (4) . Remove bolts (5) .
Illustration 3 g00949158
3. Remove screws (6) and the clips. Remove screw (7) and cap (8) . Remove clips (9) .
Illustration 4 g00949190
2/5321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 4. Remove three screws (12) and actuator (11) . Disconnect linkage (13) . Disconnect harness
assembly (14) . Remove clips (10) and separate the housing.
Illustration 5 g00949201
5. Remove blower motor (15) .
Installation Procedure
Illustration 6 g00949201
1. Install blower motor (15) into the housing.
3/5321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 7 g00949190
2. Connect the housing and install clips (10) . Connect harness assembly (14) . Connect
linkage (13) . Position actuator (11) and install three screws (12) .
Illustration 8 g00949158
3. Install clips (9) . Install cap (8) and screw (7) . Install the clips and screws (6) .
Illustration 9 g00949153
4/5321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 4. Install bolts (5) and connect hose (4) .
Illustration 10 g00949152
5. Install air filter (3) . Install cover (2) and screws (1) .
End By: Install the heating and air conditioning unit. Refer to Disassembly and Assembly,
"Heating and Air Conditioning Unit - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 3 18:41:28 UTC+0800 2019
5/5321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 321C EXCAVATOR KCR
Configuration: 321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
321C LCR Excavator Machine Systems
Media Number -RENR7108-03 Publication Date -01/04/2006 Date Updated -24/10/2018
i01934130
Refrigerant Receiver-Dryer - Remove and Install
SMCS - 7322-010
Removal Procedure
Personal injury can result from contact with refrigerant.
Contact with refrigerant can cause frost bite. Keep face and hands away
to help prevent injury.
Protective goggles must always be worn when refrigerant lines are
opened, even if the gauges indicate the system is empty of refrigerant.
Always use precaution when a fitting is removed. Slowly loosen the
fitting. If the system is still under pressure, release it slowly in a well
ventilated area.
Personal injury or death can result from inhaling refrigerant through a
lit cigarette.
Inhaling air conditioner refrigerant gas through a lit cigarette or other
smoking method or inhaling fumes released from a flame contacting air
conditioner refrigerant gas, can cause bodily harm or death.
Do not smoke when servicing air conditioners or wherever refrigerant
gas may be present.
Use a certified recovery and recycling cart to properly remove the
refrigerant from the air conditioning system.
1/4321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. NOTICE
Effective July 1, 1992 regulations prohibit the venting of any
refrigerant into the atmosphere. Refer to Caterpillar publications
Service Manuals, SENR3334, SENR5664, and NEDG5065 for the
proper procedure, the proper equipment, and the proper tools needed
in order to reclaim refrigerant from any Caterpillar equipment.
Note: Reclaim the refrigerant before any lines are loosened or any bolts are loosened.
1. Reclaim the refrigerant in the air conditioning system.
Reference: Refer to Testing and Adjusting, "Refrigerant Recovery" for the correct
procedure.
Illustration 1 g01006489
2. Remove bolts (2) and disconnect hose assemblies (1) from receiver-dryer (3).
Illustration 2 g01006490
3. Remove bolts (4), the clamp, and receiver-dryer (3).
2/4321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Installation Procedure
Illustration 3 g01006490
1. Position receiver-dryer (3). Install the clamp and bolts (4).
Illustration 4 g01006489
2. Connect hose assemblies (1) and install bolts (5) to receiver-dryer (3).
Personal injury can result from contact with refrigerant.
Contact with refrigerant can cause frost bite. Keep face and hands away
to help prevent injury.
Protective goggles must always be worn when refrigerant lines are
opened, even if the gauges indicate the system is empty of refrigerant.
Always use precaution when a fitting is removed. Slowly loosen the
fitting. If the system is still under pressure, release it slowly in a well
ventilated area.
3/4321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Personal injury or death can result from inhaling refrigerant through a
lit cigarette.
Inhaling air conditioner refrigerant gas through a lit cigarette or other
smoking method or inhaling fumes released from a flame contacting air
conditioner refrigerant gas, can cause bodily harm or death.
Do not smoke when servicing air conditioners or wherever refrigerant
gas may be present.
Use a certified recovery and recycling cart to properly remove the
refrigerant from the air conditioning system.
NOTICE
Effective July 1, 1992 regulations prohibit the venting of any
refrigerant into the atmosphere. Refer to Caterpillar publications
Service Manuals, SENR3334, SENR5664, and NEDG5065 for the
proper procedure, the proper equipment, and the proper tools needed
in order to reclaim refrigerant from any Caterpillar equipment.
3. Evacuate the air conditioning system.
Reference: Evacuate the system. Refer to Testing and Adjusting, "Refrigerant System -
Evacuate" for the correct procedure.
4. Charge the air conditioning system. The correct charge is 0.9 kg (2.0 lb).
Reference: Refer to Testing and Adjusting, "Refrigerant System - Charge" for the correct
procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 3 18:42:24 UTC+0800 2019
4/4321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 321C EXCAVATOR KCR
Configuration: 321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
321C LCR Excavator Machine Systems
Media Number -RENR7108-03 Publication Date -01/04/2006 Date Updated -24/10/2018
i01862589
Actuator Motor (Damper Assembly) - Remove and Install
SMCS - 7304-010-MQ; 7309-010-MQ; 7320-010-MQ
Removal Procedure
Start By:
a. Remove the seat support. Refer to Disassembly and Assembly, "Seat Support - Remove and
Install".
Removal Procedure for the Actuator Motor for the Floor Vent, Front and
Rear Vents
Illustration 1 g00948489
1. Remove bolts (1). Remove plate (3) and roll floormat (2) forward.
1/16321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 2 g00948628
Illustration 3 g00948629
Right rear
Illustration 4 g00948631
Left rear
2. Remove bolts (4).
2/16321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 5 g00948642
Note: Put identification marks on all of the harness assemblies for installation purposes.
3. Disconnect nine harness assemblies (5).
Illustration 6 g00948647
4. Remove bolts (7) and remove cover (6).
Illustration 7 g00948649
5. Remove five screws (8) and panel (9).
3/16321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Illustration 8 g00949512
6. Remove screw (10). Disconnect linkage (12) and remove plate (11).
Illustration 9 g00949515
7. Disconnect harness assembly (15). Remove screws (13). Remove actuator (14).
Removal Procedure for the Actuator Motor for the Temperature Control
Illustration 10 g00948489
1. Remove bolts (1). Remove plate (3) and roll floormat (2) forward.
4/16321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 11 g00948628
Illustration 12 g00948629
Right rear
Illustration 13 g00948631
Left rear
2. Remove bolts (4).
5/16321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 14 g00948642
Note: Put identification marks on all of the harness assemblies for installation purposes.
3. Disconnect nine harness assemblies (5).
Illustration 15 g00948647
4. Remove bolts (7) and remove cover (6).
Illustration 16 g00948649
5. Remove five screws (8) and panel (9).
6/16321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 8. Remove bolt (15) and remove duct (16).
Illustration 20 g00948827
9. Remove assembly (17) for the air distribution system. Use two people and remove support
assembly (18). The weight of support assembly (18) is approximately 24 kg (52 lb).
Illustration 21 g00949520
10. Disconnect linkage (20). Remove screws (21) and actuator (19).
Installation Procedure
Installation Procedure for the Actuator Motor for the Temperature Control
8/16321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 22 g00949520
1. Position actuator (19) and install screws (21). Connect linkage (20).
Illustration 23 g00948827
2. Use two people and position support assembly (18). The weight of support assembly (18) is
approximately 24 kg (52 lb). Install assembly (17) for the air distribution system.
Illustration 24 g00948820
3. Install duct (16) and bolt (15).
9/16321C LCR Excavator KCR00001-UP (MACHINE) POWERED BY 3066 Engine(SEB...
2019/10/3https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...