This document provides instructions for removing and installing the water pump, crankshaft vibration damper and pulley, crankshaft front seal, and oil pan on a Caterpillar 320D2 excavator engine. The procedures include lists of required tools, illustrations showing the component locations and part numbers, and step-by-step instructions for removal and installation of each component. Safety notices are included to keep all parts clean from contaminants.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
6. Illustration 5 g01307061
1. Install gasket (4). Install water pump (5) and bolts (9). Install gasket (7), cover (8), and bolts
(6). Tighten bolts (9) and bolts (6) in the sequence that is shown in Illustration 4 to a torque
of 22 N·m (16 lb ft).
5/6(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 6 g01306964
2. Connect hose (3).
Illustration 7 g02795203
3. Install guard (2). Install bolts (1).
End By:
a. Install the coolant tank (expansion).
b. Install the fan.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Feb 14 15:16:20 UTC+0800 2020
6/6(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 EXCAVATOR WDJ
Configuration: 320D2 & 320D2 L Excavators WDJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
320D2 Excavator Engine Supplement
Media Number -UENR0199-09 Publication Date -01/07/2015 Date Updated -25/07/2018
i05536911
Crankshaft Vibration Damper and Pulley - Remove and
Install
SMCS - 1205-010
S/N - EKT1-UP
S/N - ESG1-UP
S/N - TGJ1-UP
S/N - WDJ1-UP
S/N - XAN1-UP
S/N - XBB1-UP
S/N - XCC1-UP
Removal Procedure
Start By:
a. Remove the fan.
1. Remove the serpentine belt. Refer to Operation and Maintenance Manual, "Belt- Remove
and Install".
1/4(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 1 g01306599
1. Remove plug (1). Use a suitable pin in order to ensure that the crankshaft does not rotate.
Illustration 2 g01306601
2. Remove bolts (3) and damper (2).
Illustration 3 g01306602
3. Remove bolts (5) and retainer (6). Remove the adapter and pulley (4) as a unit.
2/4(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 4 g01306603
4. Remove pulley (7) from adapter (8).
Installation Procedure
Illustration 5 g01306603
1. Install adapter (8) to pulley (7).
Illustration 6 g01306602
3/4(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 2. Install the adapter and pulley (4) as a unit. Install retainer (6) and bolts (5). Tighten bolts (5)
to a torque of 200 N·m (148 lb ft).
Illustration 7 g01306601
3. Install damper (2) and bolts (3). Tighten bolts (3) to a torque of 115 N·m (85 lb ft).
Illustration 8 g01306599
4. Remove the suitable pin. Install plug (1). Install the serpentine belt. Refer to Operation and
Maintenance Manual, "Belt- Remove and Install".
End By:
a. Install the fan.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Feb 14 15:17:16 UTC+0800 2020
4/4(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. S/N - TMF1-UP
S/N - WDJ1-UP
S/N - XAN1-UP
S/N - XBB1-UP
S/N - XCC1-UP
S/N - YEA1-UP
S/N - ZBD1-UP
S/N - ZCS1-UP
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove".
Illustration 1 g01306599
1. Remove plug (1). Use a suitable pin to ensure that the crankshaft does not rotate.
2/5(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 2 g01306601
2. Remove bolts (3) and damper (2).
Illustration 3 g01306602
3. Remove bolts (5) and retainer (6). Remove the adapter and pulley (4) as a unit.
Illustration 4 g01306603
4. Remove pulley (7) from adapter (8).
Installation Procedure
3/5(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 5 g01306603
1. Install adapter (8) to pulley (7).
Illustration 6 g01306602
2. Install the adapter and pulley (4) as a unit. Install retainer (6) and bolts (5). Tighten bolts (5)
to a torque of 40 N·m (30 lb ft). Turn bolts (5) an extra 120 degrees.
Illustration 7 g01306601
3. Install damper (2) and bolts (3). Tighten bolts (3) to a torque of 115 N·m (85 lb ft).
4/5(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 8 g01306599
4. Remove the suitable pin. Install plug (1).
End By:
a. Install the fan. Refer to Disassembly and Assembly, "Fan - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Feb 14 15:18:12 UTC+0800 2020
5/5(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 EXCAVATOR WDJ
Configuration: 320D2 & 320D2 L Excavators WDJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
320D2 Excavator Engine Supplement
Media Number -UENR0199-09 Publication Date -01/07/2015 Date Updated -25/07/2018
i05545650
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
S/N - EKT1-UP
S/N - ESG1-UP
S/N - TGJ1-UP
S/N - WDJ1-UP
S/N - XAN1-UP
S/N - XBB1-UP
S/N - XCC1-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 367-3534 Oil Seal Removal & Installer Tool 1
Start By:
a. Remove the radiator.
b. Remove the crankshaft pulley.
NOTICE
1/4(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01989793
1. Position Tooling (A) onto crankshaft front seal (2).
2. Turn Tooling (A) in a counterclockwise direction and remove crankshaft front seal (2) from
front cover (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 367-3534 Oil Seal Removal & installer Tool 1
NOTICE
2/4(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the front cover is clean and free from damage.
Illustration 2 g01990013
2. Correctly position a new crankshaft front seal (2) in Position (X) onto front cover (1).
3. Position Tooling (A) onto crankshaft front seal (2).
4. Use Tooling (A) in order to turn crankshaft front seal (2) in clockwise direction.
5. If necessary, to apply a torque greater than 50 N·m (37 lb ft) in order to install crankshaft
front seal (2). Remove crankshaft front seal (2). Inspect the crankshaft front seal and the
front cover for faults or damage.
6. If necessary repeat Step 2 through Step 5 in order to install crankshaft front seal (2).
End By:
a. Install the crankshaft pulley.
b. Install radiator.
3/4(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. S/N - XBB1-UP
S/N - XCC1-UP
S/N - YEA1-UP
S/N - ZBD1-UP
S/N - ZCS1-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8846 Gasket Sealant 1
1. Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and
Maintenance Manual, "Engine Oil and Filter - Change".
Illustration 1 g02782017
2. Remove covers (1).
2/8(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 2 g01308777
3. Remove bolts (4) and (5). Remove oil pan (3) and gasket (2).
3/8(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
24. Illustration 3 g01308778
4. Remove screws (7). Remove frame (8) and gasket (6).
Installation Procedure
4/8(W)
w
2020/2/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
