The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It outlines the required tools and multi-step procedures for removal and installation, which include using various tools to turn the cylinder head, remove the guides and seats, and install new guides and seats at the proper depths. Safety notices are provided to keep parts clean and contain fluids properly during the process.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...shudun96087
The document provides instructions for removing and installing valve guides, valve seat inserts, and an engine oil cooler on a Caterpillar C6.4 engine. It describes the required tools and steps to remove the components, clean and prepare the parts, and install new components. The procedures include removing valves, electronic injectors, and other engine parts before accessing the components and reinstalling parts after replacing guides, seats, and the oil cooler.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...qme229722
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involves using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
This document provides instructions for removing and installing various components of the C6.4 engine, including the inlet and exhaust valve guides, inlet and exhaust valve seat inserts, engine oil cooler, and related tools. The procedures describe removing components, cleaning parts, installing new parts, and reassembling components in reverse order of removal. Precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...kesi7153062
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler by disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler by removing mounting hardware and components. Assembly is the reverse of disassembly.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...fijsekkdmdm2w
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...zan2736ban
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...shudun96087
The document provides instructions for removing and installing valve guides, valve seat inserts, and an engine oil cooler on a Caterpillar C6.4 engine. It describes the required tools and steps to remove the components, clean and prepare the parts, and install new components. The procedures include removing valves, electronic injectors, and other engine parts before accessing the components and reinstalling parts after replacing guides, seats, and the oil cooler.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...qme229722
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involves using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
This document provides instructions for removing and installing various components of the C6.4 engine, including the inlet and exhaust valve guides, inlet and exhaust valve seat inserts, engine oil cooler, and related tools. The procedures describe removing components, cleaning parts, installing new parts, and reassembling components in reverse order of removal. Precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...kesi7153062
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler by disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler by removing mounting hardware and components. Assembly is the reverse of disassembly.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...fijsekkdmdm2w
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...zan2736ban
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...f8uesjdkdmdm
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and cleaning procedures are provided, as well as instructions for lubricating and installing replacement parts.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...f7fujksekmdm8u
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...8ufjsekddm8u
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and cleaning procedures are provided, as well as instructions for lubricating and installing replacement parts.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar cat 323 d s excavator (prefix rac) service repair manual (rac0000...idkdkddmd
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and cleaning procedures are provided, as well as instructions for lubricating and installing replacement parts.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...fujkskemdmdm4r
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes:
1. Removing the valves, electronic unit injectors, and turning the cylinder head to access the valve guides.
2. Using specialty tools to remove the old valve guides and install new guides.
3. Grinding notches in the valve seats, extracting the old seats, and installing new seats using specialty tools and lowering the temperature of the seats.
4. Reinstalling the valves and electronic unit injectors after installing new guides and seats.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...ufjksemd8ujd
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described, including removal, disassembly, and reassembly steps.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...km7seydwuhdw
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...fskekkdmdmdm3e
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described, including removal, disassembly, and reassembly steps.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...jdkskmdmdm
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and associated parts. Precautions are provided to keep parts clean and contain fluids.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described, including removal, disassembly, and reassembly steps.
Caterpillar Cat 323F SA and 323F LN Excavator (Prefix FA2) Service Repair Man...yu5676962
This document provides instructions for disassembling and assembling the final drive of an excavator model 323F SA. It lists 30 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then lists 31 steps to reassemble the final drive by installing components like bearings, seals, gears, and shims in the reverse order of disassembly. Precise tools and procedures are required to properly preload the bearings during assembly.
Caterpillar Cat 323D2 and 323D2 L Excavator (Prefix JEX) Service Repair Manua...yu5676962
The document provides instructions for disassembling the final drive of an excavator model 323D2. It involves 33 steps including removing covers, gears, shafts, seals, and housings. Special tools are required and cleanliness is important to prevent dirt from entering internal parts. Weights of removed components are provided to assist with lifting and handling. Detailed illustrations supplement the text instructions.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual Instant ...yu5676962
The document provides instructions for removing the engine oil filter base from a 322C FM excavator. The procedure involves first removing the turbocharger. Then, using a strap wrench, loosen the oil filter base by turning it counterclockwise. Finally, clean the oil filter base mounting surface before installing the new oil filter base.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual Instant ...yu5676962
1. The document provides instructions for removing and installing the unit injector hydraulic pump and turbocharger on a Caterpillar 3126B engine.
2. The unit injector hydraulic pump removal instructions include disconnecting lines and harness, removing mounting bolts, and inspecting seals. Installation is the reverse.
3. Turbocharger removal requires removing bolts and nuts connecting it to the exhaust manifold and disconnecting lines. Disassembly separates housing components. Assembly reconnects parts and installation bolts the turbocharger back into place.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual Instant ...yu5676962
This document provides instructions for removing and installing a governor from a 322C FM excavator engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to remove the governor. The installation procedure outlines cleaning and lubricating parts, replacing seals, and using tools to install the governor along with associated lines, pins, and clips. Precautions are given to keep parts clean and ensure free movement of components.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...yu5676962
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The procedures include removing pins and bolts to separate the various linkage and cylinder components, as well as instructions for installing replacement components and adjusting clearances using shims. Proper lubrication of pins, bolts and other components is emphasized during assembly.
More Related Content
Similar to Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix HJC) Service Repair Manual Instant Download.pdf
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...f8uesjdkdmdm
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and cleaning procedures are provided, as well as instructions for lubricating and installing replacement parts.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...f7fujksekmdm8u
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...8ufjsekddm8u
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and cleaning procedures are provided, as well as instructions for lubricating and installing replacement parts.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar cat 323 d s excavator (prefix rac) service repair manual (rac0000...idkdkddmd
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and cleaning procedures are provided, as well as instructions for lubricating and installing replacement parts.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...fujkskemdmdm4r
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes:
1. Removing the valves, electronic unit injectors, and turning the cylinder head to access the valve guides.
2. Using specialty tools to remove the old valve guides and install new guides.
3. Grinding notches in the valve seats, extracting the old seats, and installing new seats using specialty tools and lowering the temperature of the seats.
4. Reinstalling the valves and electronic unit injectors after installing new guides and seats.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...ufjksemd8ujd
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described, including removal, disassembly, and reassembly steps.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...km7seydwuhdw
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...fskekkdmdmdm3e
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described, including removal, disassembly, and reassembly steps.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...jdkskmdmdm
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and associated parts. Precautions are provided to keep parts clean and contain fluids.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described, including removal, disassembly, and reassembly steps.
Similar to Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix HJC) Service Repair Manual Instant Download.pdf (16)
Caterpillar Cat 323F SA and 323F LN Excavator (Prefix FA2) Service Repair Man...yu5676962
This document provides instructions for disassembling and assembling the final drive of an excavator model 323F SA. It lists 30 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then lists 31 steps to reassemble the final drive by installing components like bearings, seals, gears, and shims in the reverse order of disassembly. Precise tools and procedures are required to properly preload the bearings during assembly.
Caterpillar Cat 323D2 and 323D2 L Excavator (Prefix JEX) Service Repair Manua...yu5676962
The document provides instructions for disassembling the final drive of an excavator model 323D2. It involves 33 steps including removing covers, gears, shafts, seals, and housings. Special tools are required and cleanliness is important to prevent dirt from entering internal parts. Weights of removed components are provided to assist with lifting and handling. Detailed illustrations supplement the text instructions.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual Instant ...yu5676962
The document provides instructions for removing the engine oil filter base from a 322C FM excavator. The procedure involves first removing the turbocharger. Then, using a strap wrench, loosen the oil filter base by turning it counterclockwise. Finally, clean the oil filter base mounting surface before installing the new oil filter base.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual Instant ...yu5676962
1. The document provides instructions for removing and installing the unit injector hydraulic pump and turbocharger on a Caterpillar 3126B engine.
2. The unit injector hydraulic pump removal instructions include disconnecting lines and harness, removing mounting bolts, and inspecting seals. Installation is the reverse.
3. Turbocharger removal requires removing bolts and nuts connecting it to the exhaust manifold and disconnecting lines. Disassembly separates housing components. Assembly reconnects parts and installation bolts the turbocharger back into place.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual Instant ...yu5676962
This document provides instructions for removing and installing a governor from a 322C FM excavator engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to remove the governor. The installation procedure outlines cleaning and lubricating parts, replacing seals, and using tools to install the governor along with associated lines, pins, and clips. Precautions are given to keep parts clean and ensure free movement of components.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...yu5676962
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The procedures include removing pins and bolts to separate the various linkage and cylinder components, as well as instructions for installing replacement components and adjusting clearances using shims. Proper lubrication of pins, bolts and other components is emphasized during assembly.
Caterpillar Cat 322B L EXCAVATOR (Prefix 1YS) Service Repair Manual Instant D...yu5676962
This document provides instructions for removing and installing the governor and associated components on a Caterpillar 3116 engine. The removal process involves disconnecting linkages and tubes, removing mounting bolts and clips, and using specialized tools. The installation follows the removal steps in reverse, applying lubricant to seals and ensuring proper adjustment of linkages. Required tools include various pliers and pin tools to facilitate disconnecting and reconnecting components.
Caterpillar Cat 322 L EXCAVATOR (Prefix 9RL) Service Repair Manual Instant Do...yu5676962
This document provides instructions for removing and installing a governor from a Caterpillar Cat 322 L excavator powered by a 3116 engine. The removal procedure involves disconnecting tubes, removing clips and bolts, and using special tools. The installation procedure describes cleaning and lubricating parts, replacing seals, and using tools to install the governor components in reverse order of removal. Proper torque specifications and checks are listed to ensure correct installation.
This document provides instructions for servicing the air conditioning system on Caterpillar 322 and 322L excavators. It describes safety precautions when working with refrigerant due to risks of injury. The document outlines procedures for preparing the machine, removing and installing various AC system components like lines, the compressor, and preparing the system for disassembly and reassembly. Detailed steps are provided for correctly connecting refrigerant lines and determining the proper amount of oil for recharging the system.
Caterpillar Cat 320F L Excavator (Prefix YBM) Service Repair Manual Instant D...yu5676962
The document provides instructions for removing and installing a boom cylinder on an excavator. Key steps include:
1. Lowering the boom and releasing hydraulic pressure before removal.
2. Detaching hoses and removing mounting bolts and pins to separate the cylinder from the excavator.
3. Lifting the cylinder, which weighs approximately 287kg, off the excavator using suitable lifting devices.
4. Reinstalling the cylinder by reversing the removal procedures, taking care when installing mounting pins and bolts. Proper torque specifications are provided.
This document provides instructions for removing and installing a flywheel on a 320E LRR excavator with a C6.6 engine. The removal procedure involves using guide studs and lifting equipment to support the flywheel, then removing mounting bolts. The installation procedure specifies cleaning and inspecting components, positioning the flywheel with guide studs and lifting equipment, and tightening mounting bolts to the specified torque. Instructions are also provided for removing and installing a crankshaft rear seal.
This document provides instructions for removing and installing various engine components on a Caterpillar 320E LRR excavator, including:
1. Removing and installing the crankshaft front seal using specific tools.
2. Removing and installing the front cover, which requires removing bolts in a specific order and position.
3. Installing a new gasket and front seal when reinstalling the front cover.
The document contains detailed step-by-step instructions and illustrations for completing each task while maintaining cleanliness and using the correct tools and torque specifications.
This document provides instructions for disassembling and assembling the gear pump (pilot) and main hydraulic pump on a Caterpillar 320D2 excavator. The summary includes steps to disassemble the gear pump by removing housing bolts, seals, gears, and plates. It also describes removing the main hydraulic pump by disconnecting hoses and harnesses, removing mounting bolts, and lifting out the pump along with attached auxiliary pumps and pilots.
The document provides instructions for disassembling and assembling the travel motor of a 320D2L excavator. The disassembly procedure involves removing 27 components from the travel motor body and head. The assembly procedure instructs installing the components in reverse order and provides notices to ensure proper installation of keys and engagement of parts. Tools and torque specifications are also listed.
1. The document provides instructions for removing and installing a flywheel, crankshaft rear seal, flywheel housing, and vibration damper and pulley on a 320D2L excavator.
2. The flywheel installation procedure includes cleaning and heating components, installing bolts while preventing rotation, and checking run out.
3. Crankshaft rear seal removal requires removing screws, while installation requires aligning with a tool and torquing screws in a specific sequence.
4. Flywheel housing removal and installation involves supporting with lifting devices, inspecting seals, and torquing bolts depending on grade.
This document provides instructions for removing and installing the water pump, crankshaft vibration damper and pulley, crankshaft front seal, and oil pan on a Caterpillar 320D2 excavator engine. The procedures include lists of required tools, illustrations showing the component locations and part numbers, and step-by-step instructions for removal and installation of each component. Safety notices are included to keep all parts clean from contaminants.
The document provides instructions for disassembling and assembling the final drive of a 320D2 excavator. Key steps include:
1. Removing the carrier assembly, sun gear, ring gears, and other components from the main housing.
2. Disassembling the carrier assembly by removing planetary gears, shafts, and bearings.
3. Assembling the carrier assembly by installing bearings, gears, shafts and securing with pins.
4. Installing seals, shims, gears and other components back into the main housing. Alignment and torque specifications are provided.
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D2 excavator engine. The procedure involves using special tools to compress the valve springs, remove the retainers and springs, and then install new springs and retainers. Safety precautions are outlined to prevent injury from the force of compressed springs. The process is also described for removing and installing the valves from the cylinder head.
The document provides instructions for removing and installing a fuel injection pump gear on a Caterpillar 320D2 excavator engine. Key steps include:
1. Using tools to lock the crankshaft and camshaft in position.
2. Ensuring timing marks are aligned and gears mesh correctly before installing the fuel pump gear.
3. Tightening the nut on the fuel pump gear shaft and checking backlash is within specifications.
4. Unlocking the fuel injection pump and removing locking tools before starting the engine.
Caterpillar Cat 320D2 and 320D2 L Excavator (Prefix YBK) Service Repair Manua...yu5676962
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 320D2 excavator engine. Key steps include:
1. Removing bolts from the flywheel housing and installing guide studs before lifting the housing off with a suitable device.
2. Inspecting the crankshaft rear seal for leaks and replacing if needed before cleaning surfaces and installing dowels on the cylinder block.
3. Positioning the flywheel housing onto guide studs using a lifting device, then installing and tightening bolts to secure the housing.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625003
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 384-8861 Valve Guide Remover 1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/4(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Illustration 2 g01377121
2. Use Tooling (A) in order to remove valve guides (2) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8862 Valve Guide Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/4(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Illustration 3 g01377130
1. Lubricate the outside of valve guides (2) (not shown) with clean engine oil.
2. Use Tooling (E) in order to install new valve guides (2) . Install valve guide (2) so that
valve guide (2) protrudes 16.000 mm (0.6299 inch) above Surface (X) of cylinder head (1) .
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
b. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:15:14 UTC+0800 2020
4/4(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625001
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
166-7441 Valve Seat Extractor Tool 1
6V-4194 Valve Seat Extractor (1)
1
6V-4196 Valve Seat Extractor (1)
1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
( 1 )
Component of the Valve Seat Extractor Tool Group.
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Remove".
NOTICE
Keep all parts clean from contaminants.
1/5(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Contaminants may cause rapid wear and shortened component life.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B ) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B ) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/5(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Illustration 2 g01376571
2. Use the valve seat grinder of Tooling (A) in order to notch the valve seat.
Illustration 3 g01376578
3. Use the valve seat extractor of Tooling (A) to remove the inlet and exhaust valve seats.
4. Clean the valve seat in the cylinder head. Remove any rough areas from the valve seat in the
cylinder head.
5. Repeat Steps 2 through 4 for the remaining inlet valve seat inserts and exhaust valve seat
inserts.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8859 Valve Seat Installer 1
F 384-8860 Valve Seat Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 4 g01377071
Typical Example
1. Lower the temperature of the new inlet valve seat inserts (2) . Use Tooling (E) in order to
install a new inlet valve seat insert (2) (not shown) in the cylinder head.
Illustration 5 g01376588
Typical Example
2. Lower the temperature of new exhaust valve seat inserts (3) . Use Tooling (E) and Tooling
(F) in order to install the new exhaust valve seat insert (3) (not shown) in the cylinder head.
Note: The temperature of exhaust valve seat insert (3) is lowered in order to ease the
installation of exhaust valve seat insert (3) .
3. Repeat Step 1 and 2 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
b. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Install".
4/5(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746253
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
a. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Illustration 1 g01375410
1. Disconnect harness assembly (1).
2. Remove bolts (2) and remove engine oil cooler (3). Remove gasket (4) (not shown) from the
engine cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:17:05 UTC+0800 2020
2/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746254
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
a. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the
components should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly
procedures on a clean work surface. Keep components covered and protected at all times.
1/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Illustration 1 g01375411
1. Remove bolts (9) and the washers. Remove cover (8) and gasket (7).
2. Remove nuts (5) and the washers from engine oil cooler cover (4). Remove nuts (6) and the washers
from engine oil cooler cover (4).
3. Remove engine oil cooler core (2) from engine oil cooler cover (4). Remove gaskets (1) and (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:18:01 UTC+0800 2020
2/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746255
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the gaskets for damage. Replace the components, if necessary.
1/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Illustration 1 g01375411
1. Install gaskets (3) and (1) to engine oil cooler core (2). Position engine oil cooler core (2) to engine
oil cooler cover (4).
2. Install the washers and nuts (6). Install the washers and nuts (5).
3. Install gasket (7) and position cover (8). Install the washers and bolts (9).
End By:
a. Install the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:18:56 UTC+0800 2020
2/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746256
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Illustration 1 g01375410
1. Install gasket (4) (not shown). Position engine oil cooler (3) to the engine block. Install bolts
(2).
1/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. 2. Connect harness assembly (1).
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:19:52 UTC+0800 2020
2/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751808
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
Start By:
a. Remove the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377673
1/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. 1. Remove engine oil relief valve (1).
2. Remove gasket (2) (not shown). Discard gasket (2).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01377673
1. Install a new gasket (2) (not shown).
2. Install engine oil relief valve (1). Tighten engine oil relief valve (1) to a torque of
49 ± 5 N·m (36 ± 4 lb ft).
End By:
a. Install the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:20:48 UTC+0800 2020
2/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751881
Engine Oil Bypass Valve - Remove and Install
SMCS - 1306-010-BV
Removal Procedure
Start By:
a. Remove the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377713
1. Remove engine oil bypass valve (1). Remove gasket (2) (not shown). Discard gasket (2).
1/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01377713
1. Install a new gasket (2) (not shown). Install engine oil bypass valve (1). Tighten engine oil
bypass valve (1) to a torque of 69 ± 5 N·m (51 ± 4 lb ft).
End By:
a. Install the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:21:44 UTC+0800 2020
2/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751822
Engine Oil Pump Relief Valve - Remove and Install
SMCS - 1304-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377698
1/3(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. Illustration 2 g01377701
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove engine oil pump relief valve (1).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
24. Illustration 3 g01377701
Illustration 4 g01377698
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install engine oil pump relief valve (1). Tighten engine oil pump relief valve (1) to a torque
of 59 ± 10 N·m (44 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:22:39 UTC+0800 2020
3/3(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02741773
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00607826
Note: Illustration 1 does not show that the front housing is removed from the cylinder
block.
1. Remove bolts (1) from the cover (2).
2. Remove cover (2) for the engine oil pump from the front housing. Remove gasket (3) (not
shown).
Illustration 2 g00607770
3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5)
(slip fit).
2/4(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...