Caterpillar cat 320 d2 l excavator (prefix xan) service repair manual (xan00001 and up)

Service Repair Manual
Models
320D2 and 320D2 L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 L EXCAVATOR XAN
Configuration: 320D2 & 320D2 L Excavators XAN00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
320D2 Excavator Engine Supplement
Media Number -UENR0199-09 Publication Date -01/07/2015 Date Updated -25/07/2018
i05536911
Crankshaft Vibration Damper and Pulley - Remove and
Install
SMCS - 1205-010
S/N - EKT1-UP
S/N - ESG1-UP
S/N - TGJ1-UP
S/N - WDJ1-UP
S/N - XAN1-UP
S/N - XBB1-UP
S/N - XCC1-UP
Removal Procedure
Start By:
a. Remove the fan.
1. Remove the serpentine belt. Refer to Operation and Maintenance Manual, "Belt- Remove
and Install".
1/4(W)w
2020/1/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...

Illustration 1 g01306599
1. Remove plug (1). Use a suitable pin in order to ensure that the crankshaft does not rotate.
2. Remove bolts (3) and damper (2).
3. Remove bolts (5) and retainer (6). Remove the adapter and pulley (4) as a unit.
2/4(W)w

4. Remove pulley (7) from adapter (8).
Installation Procedure
1. Install adapter (8) to pulley (7).
3/4(W)w

2. Install the adapter and pulley (4) as a unit. Install retainer (6) and bolts (5). Tighten bolts (5)
to a torque of 200 N·m (148 lb ft).
3. Install damper (2) and bolts (3). Tighten bolts (3) to a torque of 115 N·m (85 lb ft).
4. Remove the suitable pin. Install plug (1). Install the serpentine belt. Refer to Operation and
Maintenance Manual, "Belt- Remove and Install".
End By:
a. Install the fan.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 8 00:36:38 UTC+0800 2020
4/4(W)w

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05897156
Install
SMCS - 1205-010
S/N - TGJ1-UP
S/N - XAN1-UP
Removal Procedure
Start By:
a. Remove the fan.
b. Remove counter weight.
1. Remove the serpentine belt. Refer to Operation and Maintenance Manual, "Belt-
Inspect/Replace" to remove and install the belt.
1/3(W)w

1. Remove plug (1). Use a suitable pin in order to ensure that the crankshaft does not rotate.
Picture for reference only.
2. Remove bolts (3) and damper (2). The weight of damper (2) is approximately 14 kg (31 lb).
Picture for reference only.
2/3(W)w

1. Install damper (2) and pulley (7) in the reverse order of removal.
a. Tighten bolts (5) to a torque of 200 N·m (148 lb ft).
b. Tighten bolts (3) to a torque of 115 N·m (85 lb ft).
Wed Jan 8 00:37:33 UTC+0800 2020
3/3(W)w

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i06536594
Install
SMCS - 1205-010
S/N - DFM1-UP
S/N - DNP1-UP
S/N - EAL1-UP
S/N - EKT1-UP
S/N - ESG1-UP
S/N - FKK1-UP
S/N - GBA1-UP
S/N - HDM1-UP
S/N - JFM1-UP
S/N - KHR1-UP
S/N - LMA1-UP
S/N - NBT1-UP
S/N - RDZ1-UP
S/N - SDZ291-UP
S/N - STN1-UP
S/N - TGJ1-UP
1/5(W)w

S/N - TMF1-UP
S/N - WDJ1-UP
S/N - XAN1-UP
S/N - XBB1-UP
S/N - XCC1-UP
S/N - YEA1-UP
S/N - ZBD1-UP
S/N - ZCS1-UP
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove".
1. Remove plug (1). Use a suitable pin to ensure that the crankshaft does not rotate.
2/5(W)w

2. Remove bolts (3) and damper (2).
3/5(W)w

1. Install adapter (8) to pulley (7).
2. Install the adapter and pulley (4) as a unit. Install retainer (6) and bolts (5). Tighten bolts (5)
to a torque of 40 N·m (30 lb ft). Turn bolts (5) an extra 120 degrees.
3. Install damper (2) and bolts (3). Tighten bolts (3) to a torque of 115 N·m (85 lb ft).
4/5(W)w

4. Remove the suitable pin. Install plug (1).
End By:
a. Install the fan. Refer to Disassembly and Assembly, "Fan - Install".
Wed Jan 8 00:38:29 UTC+0800 2020
5/5(W)w

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05545650
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
S/N - EKT1-UP
S/N - ESG1-UP
S/N - TGJ1-UP
S/N - WDJ1-UP
S/N - XAN1-UP
S/N - XBB1-UP
S/N - XCC1-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 367-3534 Oil Seal Removal & Installer Tool 1
Start By:
a. Remove the radiator.
b. Remove the crankshaft pulley.
NOTICE
1/4(W)w

Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Position Tooling (A) onto crankshaft front seal (2).
2. Turn Tooling (A) in a counterclockwise direction and remove crankshaft front seal (2) from
front cover (1).
Table 2
Required Tools
A 367-3534 Oil Seal Removal & installer Tool 1
NOTICE
2/4(W)w

1. Ensure that the front cover is clean and free from damage.
2. Correctly position a new crankshaft front seal (2) in Position (X) onto front cover (1).
4. Use Tooling (A) in order to turn crankshaft front seal (2) in clockwise direction.
5. If necessary, to apply a torque greater than 50 N·m (37 lb ft) in order to install crankshaft
front seal (2). Remove crankshaft front seal (2). Inspect the crankshaft front seal and the
front cover for faults or damage.
6. If necessary repeat Step 2 through Step 5 in order to install crankshaft front seal (2).
End By:
a. Install the crankshaft pulley.
b. Install radiator.
3/4(W)w

Wed Jan 8 00:39:25 UTC+0800 2020
4/4(W)w

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05897166
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
S/N - TGJ1-UP
S/N - XAN1-UP
Removal Procedure
Table 1
Required Tools
Start By:
a. Remove the damper and crankshaft pulley.
NOTICE
1/3(W)w

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

2. Turn Tooling (A) in a counterclockwise direction and remove crankshaft front seal (2) from
front cover (1).
Table 2
Required Tools
NOTICE
2/3(W)w

1. Ensure that the front cover is clean and free from damage.
2. Correctly position a new crankshaft front seal (2) in Position (X) onto front cover (1).
4. Use Tooling (A) in order to turn crankshaft front seal (2) in clockwise direction.
5. If necessary, to apply a torque greater than 50 N·m (37 lb ft) in order to install crankshaft
front seal (2). Remove crankshaft front seal (2). Inspect the crankshaft front seal and the
front cover for faults or damage.
6. If necessary repeat Step 2 through Step 5 in order to install crankshaft front seal (2).
End By:
a. Install the damper and crankshaft pulley.
Wed Jan 8 00:40:20 UTC+0800 2020
3/3(W)w

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i04637217
Oil Pan - Remove and Install
SMCS - 1302-010
S/N - DFM1-UP
S/N - DNP1-UP
S/N - EAL1-UP
S/N - EKT1-UP
S/N - ESG1-UP
S/N - FKK1-UP
S/N - GBA1-UP
S/N - HDM1-UP
S/N - JFM1-UP
S/N - KHR1-UP
S/N - LMA1-UP
S/N - NBT1-UP
S/N - RDZ1-UP
S/N - SDZ291-UP
S/N - STN1-UP
S/N - TGJ1-UP
S/N - TMF1-UP
S/N - WDJ1-UP
S/N - XAN1-UP
1/8(W)w

S/N - XBB1-UP
S/N - XCC1-UP
S/N - YEA1-UP
S/N - ZBD1-UP
S/N - ZCS1-UP
Removal Procedure
Table 1
Required Tools
A 1U-8846 Gasket Sealant 1
1. Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and
Maintenance Manual, "Engine Oil and Filter - Change".
2. Remove covers (1).
2/8(W)w

Caterpillar cat 320 d2 l excavator (prefix xan) service repair manual (xan00001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (7)

Similar to Caterpillar cat 320 d2 l excavator (prefix xan) service repair manual (xan00001 and up)

Similar to Caterpillar cat 320 d2 l excavator (prefix xan) service repair manual (xan00001 and up) (20)

More from fusjfjskefksmem

More from fusjfjskefksmem (20)

Recently uploaded

Recently uploaded (17)

Caterpillar cat 320 d2 l excavator (prefix xan) service repair manual (xan00001 and up)