The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and cleaning procedures are provided, as well as instructions for lubricating and installing replacement parts.
Caterpillar cat 323 d ln excavator (prefix rac) service repair manual (rac000...fjjsekmsmmes
The document provides instructions for removing and installing valve guides and valve seat inserts in a Caterpillar C6.4 engine. It describes:
1) Removing the valves, electronic unit injectors, and turning the cylinder head upside down to access the valve guides.
2) Using specialty tools to remove the old valve guides and install new guides.
3) Notching and extracting the valve seat inserts using specialty tools before cleaning and installing new inserts.
4) Reinstalling the valves and electronic unit injectors after installing new guides and inserts.
Caterpillar cat 323 d s excavator (prefix rac) service repair manual (rac0000...fusjejkdkmse
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes:
1. Removing the valves, electronic unit injectors, and turning the cylinder head over to access the valve guides.
2. Using specialty tools to remove the old valve guides and install new guides.
3. Notching and extracting the valve seat inserts using specialty tools before cleaning and installing new inserts.
4. Installing the valve seat inserts, valves, and electronic unit injectors to complete the job.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...shudun96087
The document provides instructions for removing and installing valve guides, valve seat inserts, and an engine oil cooler on a Caterpillar C6.4 engine. It describes the required tools and steps to remove the components, clean and prepare the parts, and install new components. The procedures include removing valves, electronic injectors, and other engine parts before accessing the components and reinstalling parts after replacing guides, seats, and the oil cooler.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...qme229722
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involves using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
This document provides instructions for removing and installing various components of the C6.4 engine, including the inlet and exhaust valve guides, inlet and exhaust valve seat inserts, engine oil cooler, and related tools. The procedures describe removing components, cleaning parts, installing new parts, and reassembling components in reverse order of removal. Precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...kesi7153062
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler by disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler by removing mounting hardware and components. Assembly is the reverse of disassembly.
Caterpillar cat 323 d ln excavator (prefix rac) service repair manual (rac000...fjjsekmsmmes
The document provides instructions for removing and installing valve guides and valve seat inserts in a Caterpillar C6.4 engine. It describes:
1) Removing the valves, electronic unit injectors, and turning the cylinder head upside down to access the valve guides.
2) Using specialty tools to remove the old valve guides and install new guides.
3) Notching and extracting the valve seat inserts using specialty tools before cleaning and installing new inserts.
4) Reinstalling the valves and electronic unit injectors after installing new guides and inserts.
Caterpillar cat 323 d s excavator (prefix rac) service repair manual (rac0000...fusjejkdkmse
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes:
1. Removing the valves, electronic unit injectors, and turning the cylinder head over to access the valve guides.
2. Using specialty tools to remove the old valve guides and install new guides.
3. Notching and extracting the valve seat inserts using specialty tools before cleaning and installing new inserts.
4. Installing the valve seat inserts, valves, and electronic unit injectors to complete the job.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...shudun96087
The document provides instructions for removing and installing valve guides, valve seat inserts, and an engine oil cooler on a Caterpillar C6.4 engine. It describes the required tools and steps to remove the components, clean and prepare the parts, and install new components. The procedures include removing valves, electronic injectors, and other engine parts before accessing the components and reinstalling parts after replacing guides, seats, and the oil cooler.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...qme229722
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involves using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
This document provides instructions for removing and installing various components of the C6.4 engine, including the inlet and exhaust valve guides, inlet and exhaust valve seat inserts, engine oil cooler, and related tools. The procedures describe removing components, cleaning parts, installing new parts, and reassembling components in reverse order of removal. Precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...kesi7153062
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler by disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler by removing mounting hardware and components. Assembly is the reverse of disassembly.
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...zatao0179249295
The document provides instructions for servicing components of a Caterpillar 336D2 L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...luanxianshi27
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...cnp692569
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and tapping guides into place. Safety notices warn of potential injury from parts propelled by springs and ensure clean parts to prevent premature wear.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and tapping guides into place. Safety notices warn of potential injury from parts propelled by springs and ensure clean parts to prevent premature wear.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001...f8uesjdkdmdm
The document provides instructions for installing a hydraulic lockout control on an excavator. It describes:
1) Installing the hydraulic lockout control using bolts and securing a switch.
2) Installing a panel and screws to cover the components.
3) The document contains detailed step-by-step instructions and illustrations for assembling and disassembling various components of an excavator such as a piston motor and fan. Safety warnings are provided throughout.
This document provides assembly instructions for repairing the transmission of a 329DL excavator. It consists of 52 steps to assemble the transmission components in the correct order, including installing gaskets, bearings, pistons, seals, covers, and other parts into the pump housing. Precautions are provided for steps involving spring tension. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
This document provides instructions for disassembling and assembling the recoil spring on a 329D L excavator. It describes:
1. The required tools and sockets for disassembly and assembly.
2. The disassembly procedure which involves using a special recoil spring bench tool to safely compress the spring and remove components.
3. The assembly procedure which again uses the bench tool to compress the spring and measure its length during assembly. Proper spring length is critical.
This document provides repair instructions for a 329DL excavator transmission. It outlines 38 steps to disassemble and reassemble the transmission, including instructions to clean parts, replace seals and O-rings, measure bearing clearance using shims, and install various transmission components like gears, seals, and housing pieces. Special tools are required for tasks like installing duo-cone seals and bearing surfaces must be coated with anti-seize compound before assembly.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...f8uesjdkdmdm
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix RGA) Service Repair Manual...f8uesjdkdmdm
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, springs, and valves in the proper sequence.
3. Lifting the swing motor or drive using lifting brackets and removing bolts to separate the components.
Caterpillar Cat 326D2 L Excavator (Prefix KER) Service Repair Manual (KER0000...f8uesjdkdmdm
This document provides the disassembly procedure for a travel motor in 27 steps. It begins by cleaning the outside of the travel motor and fastening it vertically. The first steps include removing the head and various internal components like seals, springs, plates, and pistons. Later steps dismantle the rotating assembly, remove bearings from the shaft, and disassemble the barrel assembly. Throughout, care is taken to mark components for reinstallation in their original positions. Required tools are also listed.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...f8uesjdkdmdm
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing supports and clamps, and disconnecting tubes and hoses to remove the cylinder head.
3. Installing a new gasket and torquing bolts to specified values to install the cylinder head. Reconnecting all tubes, hoses and harness assemblies.
1. The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine.
2. The removal procedure includes disconnecting harness assemblies, removing bolts, and draining coolant from the cooling system.
3. The installation procedure specifies applying anti-seize compound to bolts and tightening them in a numerical sequence to the specified torques. Connecting harness assemblies and installing supports are also described.
Caterpillar Cat 326D2 L (Prefix KGY) Service Repair Manual (KGY00001 and up).pdff8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
More Related Content
Similar to Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001 and up).pdf
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...zatao0179249295
The document provides instructions for servicing components of a Caterpillar 336D2 L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...luanxianshi27
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...cnp692569
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and tapping guides into place. Safety notices warn of potential injury from parts propelled by springs and ensure clean parts to prevent premature wear.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and tapping guides into place. Safety notices warn of potential injury from parts propelled by springs and ensure clean parts to prevent premature wear.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
Similar to Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001 and up).pdf (11)
Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001...f8uesjdkdmdm
The document provides instructions for installing a hydraulic lockout control on an excavator. It describes:
1) Installing the hydraulic lockout control using bolts and securing a switch.
2) Installing a panel and screws to cover the components.
3) The document contains detailed step-by-step instructions and illustrations for assembling and disassembling various components of an excavator such as a piston motor and fan. Safety warnings are provided throughout.
This document provides assembly instructions for repairing the transmission of a 329DL excavator. It consists of 52 steps to assemble the transmission components in the correct order, including installing gaskets, bearings, pistons, seals, covers, and other parts into the pump housing. Precautions are provided for steps involving spring tension. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
This document provides instructions for disassembling and assembling the recoil spring on a 329D L excavator. It describes:
1. The required tools and sockets for disassembly and assembly.
2. The disassembly procedure which involves using a special recoil spring bench tool to safely compress the spring and remove components.
3. The assembly procedure which again uses the bench tool to compress the spring and measure its length during assembly. Proper spring length is critical.
This document provides repair instructions for a 329DL excavator transmission. It outlines 38 steps to disassemble and reassemble the transmission, including instructions to clean parts, replace seals and O-rings, measure bearing clearance using shims, and install various transmission components like gears, seals, and housing pieces. Special tools are required for tasks like installing duo-cone seals and bearing surfaces must be coated with anti-seize compound before assembly.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...f8uesjdkdmdm
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix RGA) Service Repair Manual...f8uesjdkdmdm
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, springs, and valves in the proper sequence.
3. Lifting the swing motor or drive using lifting brackets and removing bolts to separate the components.
Caterpillar Cat 326D2 L Excavator (Prefix KER) Service Repair Manual (KER0000...f8uesjdkdmdm
This document provides the disassembly procedure for a travel motor in 27 steps. It begins by cleaning the outside of the travel motor and fastening it vertically. The first steps include removing the head and various internal components like seals, springs, plates, and pistons. Later steps dismantle the rotating assembly, remove bearings from the shaft, and disassemble the barrel assembly. Throughout, care is taken to mark components for reinstallation in their original positions. Required tools are also listed.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...f8uesjdkdmdm
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing supports and clamps, and disconnecting tubes and hoses to remove the cylinder head.
3. Installing a new gasket and torquing bolts to specified values to install the cylinder head. Reconnecting all tubes, hoses and harness assemblies.
1. The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine.
2. The removal procedure includes disconnecting harness assemblies, removing bolts, and draining coolant from the cooling system.
3. The installation procedure specifies applying anti-seize compound to bolts and tightening them in a numerical sequence to the specified torques. Connecting harness assemblies and installing supports are also described.
Caterpillar Cat 326D2 L (Prefix KGY) Service Repair Manual (KGY00001 and up).pdff8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
This document provides instructions for disassembling a travel motor. It begins by having the technician clean and secure the travel motor vertically. They are instructed to mark the head and body for alignment during reassembly. Over 25 steps are then outlined to remove various components of the travel motor like the head, brake piston, plates, and barrel assembly. Throughout, technicians are warned to be careful not to damage parts and ensure components are reinstalled in their original positions.
The document provides the disassembly procedure for a travel motor in 27 steps. It begins by removing the travel motor and cleaning it. Key steps include removing the head, brake piston, friction plates, and rotating assembly. The rotating assembly contains a shaft that requires removing retaining rings and bearing races using various tools. Piston assemblies are also removed from the barrel assembly after marking their positions.
Caterpillar Cat 325D L EXCAVATOR (Prefix T2S) Service Repair Manual (T2S00001...f8uesjdkdmdm
The document provides instructions to disassemble a final drive for a 325D L excavator. Key steps include:
1. Cleaning and marking the final drive assembly.
2. Removing the cover and gears using various tools.
3. Taking apart the carrier assemblies by removing pins, washers, and gears.
4. Using presses and hammers to separate additional components from the housing.
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdff8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavator models. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, seals and housing cover. Corresponding assembly instructions are also provided, specifying the use of various tools and noting that all seals and gaskets must be replaced. Cleanliness is emphasized throughout the assembly process.
The document provides step-by-step instructions to disassemble a final drive on an excavator. It begins by removing the final drive from the machine and securing it to a repair stand. Various components like gears, shafts, seals and housings are then removed individually using an assortment of tools. Detailed illustrations accompany each step to show how to properly disassemble the final drive. Cleanliness is emphasized to prevent dirt from entering the mechanism during reassembly.
Caterpillar Cat 325D L Excavator (Prefix SCR) Service Repair Manual (SCR00001...f8uesjdkdmdm
The document provides instructions for removing and installing a lifter group on a Caterpillar C7 engine. It describes disconnecting related components like the rocker arms and pushrods. It then instructs removing bolts and side covers to access the lifter arms and shaft. Identification marks should be made on each lifter before removal to ensure proper reinstallation.
Caterpillar Cat 325D L Excavator (Prefix NAC) Service Repair Manual (NAC00001...f8uesjdkdmdm
This service repair manual provides instructions for repairing a 325D L excavator transmission. It details 33 steps for disassembling and assembling the transmission components. Cleanliness is important during repair. O-rings and seals should always be replaced. Various tools are used to install bearings, seals, gears, and other parts in the correct order. Proper torque specifications and safety precautions are noted throughout the process.
Caterpillar Cat 325D L Excavator (Prefix LAL) Service Repair Manual (LAL00001...f8uesjdkdmdm
This document provides the disassembly procedure for a 325D L excavator travel motor. It lists the required tools and gives step-by-step instructions to disassemble the various components of the travel motor. Some key steps include removing the head from the motor body, extracting the brake piston, removing plates and discs, and taking apart the rotating assembly. Proper cleaning and replacement of seals is emphasized for reassembly.
Caterpillar Cat 325D L Excavator (Prefix MCL) Service Repair Manual (MCL00001...f8uesjdkdmdm
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Fasten the final drive assembly to a repair stand and remove the cover by taking out bolts and setscrews.
2) Remove additional components from the cover including a gear, check plate, and seals.
3) Clean all components thoroughly before disassembly to prevent dirt from entering during reassembly.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625003
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 384-8861 Valve Guide Remover 1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/4
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01377121
2. Use Tooling (A) in order to remove valve guides (2) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8862 Valve Guide Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/4
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 3 g01377130
1. Lubricate the outside of valve guides (2) (not shown) with clean engine oil.
2. Use Tooling (E) in order to install new valve guides (2) . Install valve guide (2) so that
valve guide (2) protrudes 16.000 mm (0.6299 inch) above Surface (X) of cylinder head (1) .
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
b. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:29:06 UTC+0800 2020
4/4
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625001
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
166-7441 Valve Seat Extractor Tool 1
6V-4194 Valve Seat Extractor (1)
1
6V-4196 Valve Seat Extractor (1)
1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
( 1 )
Component of the Valve Seat Extractor Tool Group.
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Remove".
NOTICE
Keep all parts clean from contaminants.
1/5
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Contaminants may cause rapid wear and shortened component life.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B ) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B ) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/5
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 2 g01376571
2. Use the valve seat grinder of Tooling (A) in order to notch the valve seat.
Illustration 3 g01376578
3. Use the valve seat extractor of Tooling (A) to remove the inlet and exhaust valve seats.
4. Clean the valve seat in the cylinder head. Remove any rough areas from the valve seat in the
cylinder head.
5. Repeat Steps 2 through 4 for the remaining inlet valve seat inserts and exhaust valve seat
inserts.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8859 Valve Seat Installer 1
F 384-8860 Valve Seat Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 4 g01377071
Typical Example
1. Lower the temperature of the new inlet valve seat inserts (2) . Use Tooling (E) in order to
install a new inlet valve seat insert (2) (not shown) in the cylinder head.
Illustration 5 g01376588
Typical Example
2. Lower the temperature of new exhaust valve seat inserts (3) . Use Tooling (E) and Tooling
(F) in order to install the new exhaust valve seat insert (3) (not shown) in the cylinder head.
Note: The temperature of exhaust valve seat insert (3) is lowered in order to ease the
installation of exhaust valve seat insert (3) .
3. Repeat Step 1 and 2 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
b. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Install".
4/5
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746253
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
a. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g01375410
1. Disconnect harness assembly (1).
2. Remove bolts (2) and remove engine oil cooler (3). Remove gasket (4) (not shown) from the
engine cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:31:04 UTC+0800 2020
2/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746254
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
a. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the
components should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly
procedures on a clean work surface. Keep components covered and protected at all times.
1/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g01375411
1. Remove bolts (9) and the washers. Remove cover (8) and gasket (7).
2. Remove nuts (5) and the washers from engine oil cooler cover (4). Remove nuts (6) and the washers
from engine oil cooler cover (4).
3. Remove engine oil cooler core (2) from engine oil cooler cover (4). Remove gaskets (1) and (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:32:03 UTC+0800 2020
2/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746255
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the gaskets for damage. Replace the components, if necessary.
1/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g01375411
1. Install gaskets (3) and (1) to engine oil cooler core (2). Position engine oil cooler core (2) to engine
oil cooler cover (4).
2. Install the washers and nuts (6). Install the washers and nuts (5).
3. Install gasket (7) and position cover (8). Install the washers and bolts (9).
End By:
a. Install the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:33:03 UTC+0800 2020
2/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746256
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Illustration 1 g01375410
1. Install gasket (4) (not shown). Position engine oil cooler (3) to the engine block. Install bolts
(2).
1/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 2. Connect harness assembly (1).
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:34:02 UTC+0800 2020
2/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751808
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
Start By:
a. Remove the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377673
1/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 1. Remove engine oil relief valve (1).
2. Remove gasket (2) (not shown). Discard gasket (2).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01377673
1. Install a new gasket (2) (not shown).
2. Install engine oil relief valve (1). Tighten engine oil relief valve (1) to a torque of
49 ± 5 N·m (36 ± 4 lb ft).
End By:
a. Install the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:35:01 UTC+0800 2020
2/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751881
Engine Oil Bypass Valve - Remove and Install
SMCS - 1306-010-BV
Removal Procedure
Start By:
a. Remove the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377713
1. Remove engine oil bypass valve (1). Remove gasket (2) (not shown). Discard gasket (2).
1/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01377713
1. Install a new gasket (2) (not shown). Install engine oil bypass valve (1). Tighten engine oil
bypass valve (1) to a torque of 69 ± 5 N·m (51 ± 4 lb ft).
End By:
a. Install the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:36:00 UTC+0800 2020
2/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751822
Engine Oil Pump Relief Valve - Remove and Install
SMCS - 1304-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377698
1/3
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g01377701
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove engine oil pump relief valve (1).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 3 g01377701
Illustration 4 g01377698
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install engine oil pump relief valve (1). Tighten engine oil pump relief valve (1) to a torque
of 59 ± 10 N·m (44 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:37:00 UTC+0800 2020
3/3
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02741773
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00607826
Note: Illustration 1 does not show that the front housing is removed from the cylinder
block.
1. Remove bolts (1) from the cover (2).
2. Remove cover (2) for the engine oil pump from the front housing. Remove gasket (3) (not
shown).
Illustration 2 g00607770
3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5)
(slip fit).
2/4
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...