This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine, including:
- Removing and installing the fuel filter base
- Removing and installing the fuel injection lines
- Removing the fuel injection nozzles
- Installing new fuel injection nozzles
The summaries provide the high-level steps for each procedure in 3 sentences or less.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft. Safety notes are included to warn of potential injury from improper assembly of spring-loaded parts.
The document provides instructions for removing and installing various components of a Caterpillar 992K wheel loader, including:
1) Removing and disassembling the rear power take-off, which involves using various tools to remove nuts, bearings, and other parts.
2) Instructions for reassembling the rear power take-off by installing bearings and other components in the reverse order of disassembly.
3) Procedures for removing and installing the vibration damper and pulley, which includes using guide studs and lifting equipment to handle the heavy components.
The document contains detailed step-by-step instructions along with illustrations to correctly perform maintenance on specific parts of the 992K
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
This document provides instructions for removing and disassembling the transmission of a 416D Backhoe Loader. It outlines 14 steps to remove the transmission, which includes draining fluids, removing mounting bolts, and lowering the transmission. It then details disassembling the transmission into its major components, such as removing the front and rear output shafts, planetary gears, clutch packs, seals, and bearings. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
The document provides instructions for removing and installing the fuel transfer pump on a Caterpillar 322N excavator powered by a 3116 engine. It details removing the pump cover, spring, piston and seals. It also describes inspecting parts and lubricating them with oil during installation. Installation involves reversing the removal steps and ensuring proper alignment of components.
The document provides instructions for removing and installing final drive sprockets, travel brake valves, and travel motors on a 322-A excavator model. Key steps include separating the track assemblies, using tools to support heavy components like the sprocket while removing fasteners, cleaning mating surfaces, replacing seals, and torquing fasteners to the specified values. The process also requires draining oil from the final drive and hydraulic system before removing components.
This document provides instructions for disassembling the control valve (auxiliary) on a 322C excavator. It describes removing and disassembling various components of the control valve such as solenoid valves, line relief valves, fittings, seals, and spools. Cleanliness is emphasized to prevent contamination of hydraulic systems during disassembly and reassembly. Detailed illustrations and part numbers are provided for each step. Personal protective equipment is recommended when removing or releasing parts under spring pressure.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft. Safety notes are included to warn of potential injury from improper assembly of spring-loaded parts.
The document provides instructions for removing and installing various components of a Caterpillar 992K wheel loader, including:
1) Removing and disassembling the rear power take-off, which involves using various tools to remove nuts, bearings, and other parts.
2) Instructions for reassembling the rear power take-off by installing bearings and other components in the reverse order of disassembly.
3) Procedures for removing and installing the vibration damper and pulley, which includes using guide studs and lifting equipment to handle the heavy components.
The document contains detailed step-by-step instructions along with illustrations to correctly perform maintenance on specific parts of the 992K
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
This document provides instructions for removing and disassembling the transmission of a 416D Backhoe Loader. It outlines 14 steps to remove the transmission, which includes draining fluids, removing mounting bolts, and lowering the transmission. It then details disassembling the transmission into its major components, such as removing the front and rear output shafts, planetary gears, clutch packs, seals, and bearings. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
The document provides instructions for removing and installing the fuel transfer pump on a Caterpillar 322N excavator powered by a 3116 engine. It details removing the pump cover, spring, piston and seals. It also describes inspecting parts and lubricating them with oil during installation. Installation involves reversing the removal steps and ensuring proper alignment of components.
The document provides instructions for removing and installing final drive sprockets, travel brake valves, and travel motors on a 322-A excavator model. Key steps include separating the track assemblies, using tools to support heavy components like the sprocket while removing fasteners, cleaning mating surfaces, replacing seals, and torquing fasteners to the specified values. The process also requires draining oil from the final drive and hydraulic system before removing components.
This document provides instructions for disassembling the control valve (auxiliary) on a 322C excavator. It describes removing and disassembling various components of the control valve such as solenoid valves, line relief valves, fittings, seals, and spools. Cleanliness is emphasized to prevent contamination of hydraulic systems during disassembly and reassembly. Detailed illustrations and part numbers are provided for each step. Personal protective equipment is recommended when removing or releasing parts under spring pressure.
Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...udjkskdmmd
This document provides instructions for removing and installing a governor from a 322 L, 322 LN, and 322 N excavator powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and tubes connecting the governor to the engine. Individual parts like O-rings and seals must be removed and replaced. The installation procedure specifies lubricating new seals and using tools to reconnect everything in the reverse order of removal. Special attention is given to properly adjusting the fuel setting after installing the new governor.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...udjkskdmmd
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
- Removing and installing the crankshaft vibration damper and pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing and installing the front cover.
- Removing and installing the front housing.
The summaries provide the high level steps for removing and installing the listed components from the 3126B engine in 3 sentences or less per the request.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
This document provides instructions for removing and installing various engine components on a Caterpillar 993K wheel loader, including:
- Inlet and exhaust valves, guides, and seat inserts
- Engine oil filter base
- Engine oil cooler
The procedures describe using various tools to remove parts like the cylinder head, valves, guides, filters, hoses, and the oil cooler assembly. Installation is generally the reverse of removal, with instructions to clean parts, apply sealant or lubricant, and torque fasteners to the specified values. Safety notices warn of spring hazards and keeping parts clean to prevent wear.
This document provides instructions for removing and installing various components of the rear power take-off (RPTO) and vibration damper on a 993K wheel loader. It describes in detail how to disassemble the RPTO by removing nuts, bearings, and gears. It then explains the reverse process to assemble the RPTO. Separate sections provide procedures for installing the RPTO and removing/installing the vibration damper and pulley, including the use of various tools. Detailed illustrations accompany each step.
This document provides instructions for disassembling and assembling the parking brake on a Caterpillar 993K Wheel Loader. It describes removing 16 different components of the parking brake including pistons, springs, discs, plates, and housings. Detailed illustrations and torque specifications are provided for each step of disassembly and assembly. Tools required include a slide hammer, puller, driver group, link brackets, lever puller hoist, and sealant. Personnel safety warnings and proper procedures are noted throughout.
The document provides instructions for disassembling and assembling the torque converter of a 966F wheel loader. It describes 31 steps to disassemble the various components of the torque converter including removing housing bolts, gears, bearings, seals, and other parts. It then describes 26 steps for reassembling the torque converter components in reverse order, noting specific alignment and torque specifications. The overall document provides detailed technical instructions for maintenance personnel to fully disassemble and reassemble the machine's torque converter.
The document provides instructions for disassembling and assembling the service brake on a Caterpillar 993K wheel loader. The disassembly procedure involves removing reaction plates, discs, springs, pistons, seals and other brake components. The assembly procedure describes installing these components in reverse order and applying grease and torques as specified. Safety precautions are provided to prevent injury from spring forces.
The document provides instructions for servicing components of a Caterpillar 3306 engine, including:
- Installing and removing fuel injection nozzles
- Disassembling and assembling the fuel ratio control
- Removing and installing the fuel shutoff solenoid
The instructions include diagrams illustrating the components and numbered steps for disassembly, cleaning, inspection, and reassembly of the parts. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the swing drive of a M325C MH wheeled excavator. It lists 31 steps for disassembly, removing components like the cover, carrier assembly, gears, shafts, and seals. It then lists 35 steps for assembly, installing these components in reverse order along with tools needed and special instructions. Precautions are given to contain fluids, clean parts thoroughly, and use lifting devices due to component weights up to 310 kg.
This document provides instructions for disassembling the front final drive, carrier, hubs, and brakes of an M320 Excavator. It outlines 28 steps to remove components like the planetary carrier, sun gear, ring gear, brake piston, hub, bearings and seals. Various tools are required including retaining ring pliers, pullers, wrenches and adapters. Safety notices are included about containing fluids, releasing hydraulic pressure and avoiding damage during disassembly.
This document provides instructions for disassembling and assembling the rear axle of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, roller bearings, brake discs, carrier gear, and hub. The assembly procedure instructs installing these 23 components in reverse order and provides torque specifications for tightening nuts. Tools required include retaining ring pliers, drivers, a spanner, pry bar, three jaw puller, and torque multiplier group.
This document provides instructions for disassembling and assembling the input transfer gears of a 993K wheel loader transmission. It is a 26 step process that involves removing housing components and gears, inspecting and replacing parts as needed, heating and pressing bearings into place, measuring gear end play, and reassembling components using torque specifications and feeler gauges to ensure proper spacing. Tools required include eyebolts, drivers, dial indicators, thickness gauges, and lifting devices to maneuver the various heavy transmission parts.
This document provides instructions for removing and installing a fuel injection control linkage on a Caterpillar M325B wheeled excavator with a 3116 engine. The removal procedure involves using special tools to remove clips and pins connecting the governor and linkage. The installation involves applying lubricant to seals, connecting the governor and linkage with pins and clips, and adjusting the fuel setting. Special manuals and tools are referenced for additional guidance on governors, linkages, and adjustments.
This document provides instructions for disassembling and assembling the parking brake on a Caterpillar 993K wheel loader. The disassembly process involves removing 16 specific components from the parking brake assembly using various tools. The assembly process reverses this, instructing technicians to install 17 components in the proper order using tools as needed. Safety precautions are provided regarding releasing spring tension.
The document provides instructions for removing and installing an engine on a 432E Backhoe Loader. It lists 50 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses and hoses, and removing mounting hardware. It then lists 21 steps for installing the engine, which is the reverse of the removal process and includes reconnecting all wiring harnesses, hoses, and installing new mounting hardware. Special tools are required to lift and support the heavy engine during removal and installation.
This document provides instructions for disassembling the transmission of a 432E Backhoe Loader. It lists required tools and outlines 50 steps to disassemble the various transmission components, including removing gears, bearings, seals, and other parts from the front and rear output shafts, countershaft, idler shaft, input shaft, and transmission case. Detailed illustrations accompany each step to show how to use pulling and pressing tools to properly remove the parts. Safety precautions are provided for steps involving compressed springs.
This document provides assembly instructions for the axle housing of a 432F backhoe loader. It outlines 37 steps to assemble components like bearing cups, cones, brake cylinders, seals, gears, and pins. Precise measurements and torque specifications are given for each step to ensure proper assembly. Cleanliness is stressed as important to prevent contamination and wear of parts.
The document provides instructions for removing, disassembling, assembling, and installing transmission solenoid valves on Caterpillar 416D backhoe loaders. It describes removing floorplates, disconnecting wiring, and removing bolts to access the valves. Disassembly steps include removing nuts, covers, seals, and other parts. Assembly requires cleaning parts and replacing seals before reinstalling components. Precautions are outlined for safety and containing fluids.
Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...udjkskdmmd
This document provides instructions for removing and installing a governor from a 322 L, 322 LN, and 322 N excavator powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and tubes connecting the governor to the engine. Individual parts like O-rings and seals must be removed and replaced. The installation procedure specifies lubricating new seals and using tools to reconnect everything in the reverse order of removal. Special attention is given to properly adjusting the fuel setting after installing the new governor.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...udjkskdmmd
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
- Removing and installing the crankshaft vibration damper and pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing and installing the front cover.
- Removing and installing the front housing.
The summaries provide the high level steps for removing and installing the listed components from the 3126B engine in 3 sentences or less per the request.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
This document provides instructions for removing and installing various engine components on a Caterpillar 993K wheel loader, including:
- Inlet and exhaust valves, guides, and seat inserts
- Engine oil filter base
- Engine oil cooler
The procedures describe using various tools to remove parts like the cylinder head, valves, guides, filters, hoses, and the oil cooler assembly. Installation is generally the reverse of removal, with instructions to clean parts, apply sealant or lubricant, and torque fasteners to the specified values. Safety notices warn of spring hazards and keeping parts clean to prevent wear.
This document provides instructions for removing and installing various components of the rear power take-off (RPTO) and vibration damper on a 993K wheel loader. It describes in detail how to disassemble the RPTO by removing nuts, bearings, and gears. It then explains the reverse process to assemble the RPTO. Separate sections provide procedures for installing the RPTO and removing/installing the vibration damper and pulley, including the use of various tools. Detailed illustrations accompany each step.
This document provides instructions for disassembling and assembling the parking brake on a Caterpillar 993K Wheel Loader. It describes removing 16 different components of the parking brake including pistons, springs, discs, plates, and housings. Detailed illustrations and torque specifications are provided for each step of disassembly and assembly. Tools required include a slide hammer, puller, driver group, link brackets, lever puller hoist, and sealant. Personnel safety warnings and proper procedures are noted throughout.
The document provides instructions for disassembling and assembling the torque converter of a 966F wheel loader. It describes 31 steps to disassemble the various components of the torque converter including removing housing bolts, gears, bearings, seals, and other parts. It then describes 26 steps for reassembling the torque converter components in reverse order, noting specific alignment and torque specifications. The overall document provides detailed technical instructions for maintenance personnel to fully disassemble and reassemble the machine's torque converter.
The document provides instructions for disassembling and assembling the service brake on a Caterpillar 993K wheel loader. The disassembly procedure involves removing reaction plates, discs, springs, pistons, seals and other brake components. The assembly procedure describes installing these components in reverse order and applying grease and torques as specified. Safety precautions are provided to prevent injury from spring forces.
The document provides instructions for servicing components of a Caterpillar 3306 engine, including:
- Installing and removing fuel injection nozzles
- Disassembling and assembling the fuel ratio control
- Removing and installing the fuel shutoff solenoid
The instructions include diagrams illustrating the components and numbered steps for disassembly, cleaning, inspection, and reassembly of the parts. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the swing drive of a M325C MH wheeled excavator. It lists 31 steps for disassembly, removing components like the cover, carrier assembly, gears, shafts, and seals. It then lists 35 steps for assembly, installing these components in reverse order along with tools needed and special instructions. Precautions are given to contain fluids, clean parts thoroughly, and use lifting devices due to component weights up to 310 kg.
This document provides instructions for disassembling the front final drive, carrier, hubs, and brakes of an M320 Excavator. It outlines 28 steps to remove components like the planetary carrier, sun gear, ring gear, brake piston, hub, bearings and seals. Various tools are required including retaining ring pliers, pullers, wrenches and adapters. Safety notices are included about containing fluids, releasing hydraulic pressure and avoiding damage during disassembly.
This document provides instructions for disassembling and assembling the rear axle of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, roller bearings, brake discs, carrier gear, and hub. The assembly procedure instructs installing these 23 components in reverse order and provides torque specifications for tightening nuts. Tools required include retaining ring pliers, drivers, a spanner, pry bar, three jaw puller, and torque multiplier group.
This document provides instructions for disassembling and assembling the input transfer gears of a 993K wheel loader transmission. It is a 26 step process that involves removing housing components and gears, inspecting and replacing parts as needed, heating and pressing bearings into place, measuring gear end play, and reassembling components using torque specifications and feeler gauges to ensure proper spacing. Tools required include eyebolts, drivers, dial indicators, thickness gauges, and lifting devices to maneuver the various heavy transmission parts.
This document provides instructions for removing and installing a fuel injection control linkage on a Caterpillar M325B wheeled excavator with a 3116 engine. The removal procedure involves using special tools to remove clips and pins connecting the governor and linkage. The installation involves applying lubricant to seals, connecting the governor and linkage with pins and clips, and adjusting the fuel setting. Special manuals and tools are referenced for additional guidance on governors, linkages, and adjustments.
This document provides instructions for disassembling and assembling the parking brake on a Caterpillar 993K wheel loader. The disassembly process involves removing 16 specific components from the parking brake assembly using various tools. The assembly process reverses this, instructing technicians to install 17 components in the proper order using tools as needed. Safety precautions are provided regarding releasing spring tension.
The document provides instructions for removing and installing an engine on a 432E Backhoe Loader. It lists 50 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses and hoses, and removing mounting hardware. It then lists 21 steps for installing the engine, which is the reverse of the removal process and includes reconnecting all wiring harnesses, hoses, and installing new mounting hardware. Special tools are required to lift and support the heavy engine during removal and installation.
This document provides instructions for disassembling the transmission of a 432E Backhoe Loader. It lists required tools and outlines 50 steps to disassemble the various transmission components, including removing gears, bearings, seals, and other parts from the front and rear output shafts, countershaft, idler shaft, input shaft, and transmission case. Detailed illustrations accompany each step to show how to use pulling and pressing tools to properly remove the parts. Safety precautions are provided for steps involving compressed springs.
This document provides assembly instructions for the axle housing of a 432F backhoe loader. It outlines 37 steps to assemble components like bearing cups, cones, brake cylinders, seals, gears, and pins. Precise measurements and torque specifications are given for each step to ensure proper assembly. Cleanliness is stressed as important to prevent contamination and wear of parts.
The document provides instructions for removing, disassembling, assembling, and installing transmission solenoid valves on Caterpillar 416D backhoe loaders. It describes removing floorplates, disconnecting wiring, and removing bolts to access the valves. Disassembly steps include removing nuts, covers, seals, and other parts. Assembly requires cleaning parts and replacing seals before reinstalling components. Precautions are outlined for safety and containing fluids.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564836
Fuel Filter Base - Remove and Install
SMCS - 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/4(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00813127
1. Use Tool (A) to remove fuel filter (3) from fuel filter base (2) .
Note: It is not necessary to remove the fuel filter in order to remove the fuel filter base.
2. Remove banjo bolts (1) and copper washers in order to disconnect the fuel lines (4) from the
fuel filter base (2).
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
Illustration 2 g00813147
3. Remove two bolts (5) and the washers that secure the fuel filter base (2) to the air inlet
manifold. Remove the fuel filter base (2) from the fuel filter bracket.
Installation Procedure
2/4(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00813147
1. Place the fuel filter base (2) in position on the fuel filter bracket. Install the washers and two
bolts (5) that secure the fuel filter base tothe fuel filter bracket.
Illustration 4 g00813127
2. Install the banjo bolts (1) and install new copper washers in order to connect the fuel lines
(4) to the fuel filter base (2) .
3. If the fuel filter was removed, install the fuel filter (3) to the fuel filter base (2). Tighten the
fuel filter by hand according to the instructions that are shown on the fuel filter. Do not
overtighten the fuel filter.
3/4(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565021
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
Start By:
A. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/5(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 1 g00606301
The 3066 Engine is shown.
1. Remove the bolts (1), the washers, and the clamps (2), which secure the fuel lines to the
inlet manifold (3) .
Illustration 2 g00606310
2. Disconnect the fuel injection lines (4) from the fuel injection nozzles (5) .
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
2/5(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 3 g00606314
Fuel injection pump for a 3066 Engine
3. Disconnect the end of the fuel injection lines (4) from the fuel injection pump (6) .
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
4. Remove the fuel injection lines (4) from the engine.
Illustration 4 g00606317
5. Loosen the acorn nuts (7), which secure the fuel return line to the fuel injection nozzles.
6. Remove one bolt (8) and the washer from the clamp that secures the fuel return line to the
intake manifold.
Note: The clamp will remain with the fuel return line, when the fuel return line is removed
from the engine.
7. Disconnect fitting (9). Remove fuel return line (10) from the engine.
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
3/5(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 5 g00606317
1. Place the fuel return line (10) in position on the engine. Connect fitting (9) of the fuel return
line to the fuel injection pump.
2. Install the washer and bolt (8) through the clamp in order to secure the fuel return line to the
inlet manifold.
3. Install the fuel return line (10) to the fuel injection nozzles. Secure the fuel return line to the
fuel injection nozzle with acorn nuts (7) .
4/5(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 6 g00606399
Fuel injection pump for a 3066 Engine
4. Place the fuel injection lines (4) on the engine.
5. Connect the fuel injection lines (4) to the fuel injection pump (6) .
6. Connect the fuel injection lines (4) to the fuel injection nozzles (5) .
Note: The fuel lines (4) should be connected at the fuel injection nozzle (5) and at the fuel
injection pump (6) before tightening the nuts for the fuel injection line.
7. Tighten the nuts for the fuel injection line to a torque of 25 N·m (18 lb ft).
Illustration 7 g00606301
Fuel lines for a 3066 Engine
8. Install the clamps (2), the washers, and the bolts (1), which secure the fuel lines to the inlet
manifold (3) .
End By: Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 19:21:00 UTC+0800 2019
5/5(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01151321
Fuel Injection Nozzles - Remove
SMCS - 1254-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B 9U-6278 Adapter 1
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 1 g00652319
1. Remove bolt (1) and the washer that secures the clamp (2) to the cylinder head assembly.
2. Remove the clamp (2) that secures the fuel injection nozzle (3) in position in the cylinder
head assembly.
Note: Put caps or plugs on all openings immediately in order to prevent contamination in
the fuel system.
Note: Mark the clamp for later installation.
3. Install Tool (B) (not shown) to the fuel injection nozzle.
Note: Tool (B) is installed at the connection (4) for the fuel injection lines.
4. Connect Tool (A) (not shown) to Tool (B) in order to carefully remove fuel injection nozzle
(3) .
Note: Align the centerline of Tool (A) with the extended centerline of fuel injection nozzle
(3). This procedure will help prevent distortion of the fuel injection nozzle which can cause
the fuel injection nozzle to bend or break.
5. Remove the seat washer from the fuel injection nozzle.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 19:21:56 UTC+0800 2019
2/2(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01151648
Fuel Injection Nozzles - Install
SMCS - 1254-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00652319
1/2(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. 1. Install a new seat washer (5) .
2. Install fuel injection nozzle (3).
3. Install clamp (2), the washer, and bolt (1) that secures the fuel injection nozzle to the
cylinder head assembly.
4. Tighten bolt (1), that secures the fuel injection nozzle, to a torque of 22 N·m (16 lb ft).
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 19:22:51 UTC+0800 2019
2/2(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615152
Fuel Shutoff Solenoid - Remove and Install
SMCS - 1259-010
Removal Procedure
Illustration 1 g00618938
1. Disconnect two wire leads (1). Mark the wires for later installation.
2. Disconnect actuator lever (2) from the governor lever.
3. Remove two bolts (3) and washers that secure the fuel shutoff solenoid to the bracket.
4. Remove shutoff solenoid (4) from the bracket.
Installation Procedure
1/2(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 2 g00618938
1. Place the shutoff solenoid (4) in position on the bracket.
2. Install the two washers and bolts (3) that secure the fuel shutoff solenoid to the bracket.
3. Connect actuator lever (2) to the governor lever.
4. Connect two wire leads (1) to the fuel shutoff solenoid. Ensure that the wires are properly
connected.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 19:23:47 UTC+0800 2019
2/2(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565175
Fuel Injection Pump - Remove
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6124 Universal Metric Socket Set 1
B 9U-6128 Universal Metric Socket (1)
1
( 1 )
Part of the Universal Metric Socket Set
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
1/3(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Ensure that the engine is the top center position on number one piston. Refer to Testing and
Adjusting, "Finding Center Position for No. 1 Piston".
Illustration 1 g00813442
2. Remove bolts (1) and washers that secure the cover (2) to the engine front housing.
3. Remove the access cover. Note the timing marks on the fuel injection pump drive gear and
the idler gear for later installation.
Illustration 2 g00813430
2/3(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. 4. Scribe a line across the front plate (3) and the mounting flange for the fuel injection pump
(4). This ensures proper alignment for the installation of fuel injection pump (8) .
5. Loosen fitting (5) for oil line (6) .
6. Remove oil line (6) from nipple (7) (not shown).
Note: Put caps or plugs on all openings immediately in order to prevent contamination.
7. Use a lifting sling and a hoist in order to secure the fuel injection pump. The weight of the
fuel injection pump is 13 kg (29 lb).
Note: Use Tool (B) to remove the bolts and the washers that mount the fuel injection pump
(8) .
8. Remove bolt (9) and the washer from the cylinder block.
9. Remove four bolts (10) and the washers that secure the fuel injection pump to the front
housing.
Illustration 3 g00813593
10. Remove the fuel injection pump (8). The gear and the mounting flange will remain with the
fuel injection pump.
Note: The fuel injection pump must be mounted to the engine in order to loosen the nut for
the drive gear.
Note: Do not rotate the engine after the fuel injection pump is removed.
11. Ensure that the old gasket material is removed from all mating surfaces of the pump
mounting flange and the face of the fuel injection pump flange.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 19:24:43 UTC+0800 2019
3/3(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565619
Fuel Injection Pump - Install
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part number Part Description Qty
A 9U-6124 Universal Metric Socket Set 1
B 9U-6128 Universal Metric Socket (1)
1
( 1 )
Part of the Universal Metric Socket Set
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: If the nut for the fuel injection pump drive gear is removed, you must tighten the nut
for the fuel injection pump drive gear to 88 ± 5 N·m (65 ± 4 lb ft).
1/2(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 1 g00813430
1. Use a lifting sling and a hoist in order to secure the fuel injection pump (8). The weight of
the fuel injection pump is 13 kg (29 lb).
2. Install a new gasket and install fuel injection pump (8) .
3. Ensure that the engine is in the top center position on No. 1 piston. Refer to Testing and
Adjusting, "Finding Top Center Position for No. 1 Piston".
4. Ensure that the mark on the front plate (3) and the mark on the fuel injection pump flange
(4) are aligned.
Refer to Testing and Adjusting, "Fuel Injection Timing-Check" for more information on
fuel injection pump timing.
Note: Use Tool (B) to install the bolts and washers that secure the fuel injection pump to the
cylinder block.
5. Install the washers and bolts (9) that secure the fuel injection pump to the engine cylinder
block.
6. Remove the sling from the fuel injection pump.
7. Connect oil line (6) to nipple (7) (not shown).
8. Tighten fitting (5) for oil line (6) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 19:25:39 UTC+0800 2019
2/2(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564499
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 1 g00608136
1. Loosen the hose clamp (1) on hose (2) .
2. Remove hose (2) from the turbocharger (3) .
Illustration 2 g00812846
3. Disconnect oil supply line (4) from the cylinder block.
4. Loosen two clamps (5) on hose (7) .
5. Slide hose (7) off fitting (8) onto oil return line (6) .
2/3(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 3 g00608177
6. Remove eight nuts (9) from the studs on the exhaust manifold.
Note: The four studs have two nuts for a total of eight nuts.
7. Remove turbocharger (3), oil supply line (4), and oil return line (6) as an unit.
8. Remove metal gasket (10) (not shown). Check the gasket for wear or damage. Replace the
gasket, if necessary.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 19:26:34 UTC+0800 2019
3/3(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615171
Turbocharger - Disassemble
SMCS - 1052-015
Disassembly Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/4(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. 1. Place an index mark on all of the components. The marks will help to align the components
during the assembly procedure.
Illustration 1 g00608212
2. Remove two bolts (1) from the oil return line. Remove bolt (2) from the oil supply line.
3. Remove oil return line (3) from the cartridge.
4. Remove oil supply line (4) from the cartridge.
Illustration 2 g00608210
5. Remove gasket (5) from the cartridge.
6. Remove gasket (6) from the turbine housing.
2/4(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. Illustration 3 g00608342
7. Remove the bolt and nut (7) from clamp (8). Remove clamp (8) that secures the turbine
housing (9) to the cartridge (10) .
8. Separate turbine housing (9) from the cartridge (10) .
Illustration 4 g00608415
Illustration 5 g00608452
3/4(W)
w
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...