This document provides instructions for removing and installing a fuel injection pump on a 320D2 excavator. Key steps include:
1. Turning off fuel and battery power. Locking the crankshaft and camshaft using tools.
2. Cleaning the pump and area. Disconnecting fuel lines and capping openings. Removing mounting bolts and bracket.
3. Inspecting the housing bore. Installing a new O-ring and bolts. Ensuring proper timing. Reconnecting lines and installing the pump gear.
The instructions provide safety warnings and emphasize cleanliness when working on the fuel system. Tools are listed and illustrations show the pump and surrounding components.
Caterpillar cat 426 c backhoe loader (prefix 1mr) service repair manual (1mr0...fujsjefjkskekfm
This document provides instructions for removing and installing a cylinder head on a 3054 engine. The removal procedure involves draining fluids, removing various components attached to the cylinder head like the air inlet manifold and fuel injection nozzles, and then loosening bolts to lift the cylinder head off. The installation procedure specifies cleaning surfaces, positioning the cylinder head gasket and cylinder head, tightening bolts in a sequence, and further tightening bolts using a degree wheel. Tools required include guide bolts and a degree wheel.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fujsjefjkskekfm
This document provides instructions for removing and installing piston and connecting rod bearings on a 3054 engine. The key steps are:
1. Remove the engine oil pan to access the connecting rods.
2. Remove bolts and other components to access the connecting rods, including the engine oil relief valve, oil line, and oil strainer.
3. Turn the crankshaft to position the piston at bottom center and remove either two bolts and nuts (for type A connecting rods) or two bolts (for type B connecting rods) to separate the connecting rod cap.
Caterpillar cat 312 c excavator (prefix fds) service repair manual (fds00301 ...fjsjjekdkme
1. The document provides instructions for removing and installing the front housing of a 312C excavator engine.
2. To remove the front housing, several other components must first be removed, including the alternator, water pump, and crankshaft pulley. Bolts securing the front housing to other parts are then loosened and removed.
3. Installation involves cleaning surfaces, installing new seals if needed, and securing the front housing with bolts to the cylinder block, oil pan, and other parts. Timing gear alignment must also be checked during installation.
Caterpillar cat 140 h motor grader (prefix 8jm) service repair manual (8jm000...yhhjjkfkseme
This document provides instructions for removing and assembling the fuel injection pump housing and governor from a Caterpillar 3306 engine. It describes 10 steps to remove the components, including disconnecting fuel lines and other connections, removing mounting bolts and nuts, and lifting out the assembly. It then describes 8 steps to disassemble the housing further. The assembly section outlines 9 steps, including installing bearings in the proper locations and depths, inserting the camshaft, washer, and snap ring. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fusjejfskekfmsme
This document provides instructions for removing and installing a camshaft gear on a Caterpillar 3054 engine. It describes:
1) Rotating the crankshaft to align timing marks and removing the bolt and washer from the camshaft gear.
2) Using a puller tool to remove the camshaft gear and inspecting it for wear or damage.
3) Installing the camshaft gear, checking that the timing marks are aligned, and tightening the bolt.
Caterpillar cat el200 b excavator (prefix 4sg) service repair manual (4sg0000...udfjjsjkekemm
This document provides instructions for removing and installing engine accessories for an excavator model EL200B powered by an S6KT engine. It describes in detail removing components like the turbocharger, exhaust manifold, thermostat, fuel filter, injection nozzles, inlet manifold, and more. When installing accessories, it notes to follow the reverse removal procedure and ensure matching marks on gears are aligned to have the #1 piston at top dead center on compression.
The document provides instructions for removing the fuel injection pump from a 320D2 excavator with a C7.1 engine. Key steps include:
1. Turning the fuel supply and battery disconnect switch to the off position.
2. Using tools to lock the crankshaft and camshaft in position.
3. Disconnecting fuel lines from the pump and capping the lines.
4. Removing mounting bolts and carefully removing the fuel injection pump.
The document emphasizes safety precautions for working on the high pressure fuel system and provides illustrations of the pump and surrounding components.
Komatsu PC220LC-7L Excavator Service Repair Manual SN:A86001 and upudfjjsjefkkekmm
This shop manual provides instructions for servicing the PC200LC-7L and PC220LC-7L hydraulic excavators. It details removal and installation procedures for components like the radiator, hydraulic oil cooler, and engine/hydraulic pumps. Safety precautions are outlined and technicians are advised to follow the manual closely to properly service the excavators and avoid injury.
Caterpillar cat 426 c backhoe loader (prefix 1mr) service repair manual (1mr0...fujsjefjkskekfm
This document provides instructions for removing and installing a cylinder head on a 3054 engine. The removal procedure involves draining fluids, removing various components attached to the cylinder head like the air inlet manifold and fuel injection nozzles, and then loosening bolts to lift the cylinder head off. The installation procedure specifies cleaning surfaces, positioning the cylinder head gasket and cylinder head, tightening bolts in a sequence, and further tightening bolts using a degree wheel. Tools required include guide bolts and a degree wheel.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fujsjefjkskekfm
This document provides instructions for removing and installing piston and connecting rod bearings on a 3054 engine. The key steps are:
1. Remove the engine oil pan to access the connecting rods.
2. Remove bolts and other components to access the connecting rods, including the engine oil relief valve, oil line, and oil strainer.
3. Turn the crankshaft to position the piston at bottom center and remove either two bolts and nuts (for type A connecting rods) or two bolts (for type B connecting rods) to separate the connecting rod cap.
Caterpillar cat 312 c excavator (prefix fds) service repair manual (fds00301 ...fjsjjekdkme
1. The document provides instructions for removing and installing the front housing of a 312C excavator engine.
2. To remove the front housing, several other components must first be removed, including the alternator, water pump, and crankshaft pulley. Bolts securing the front housing to other parts are then loosened and removed.
3. Installation involves cleaning surfaces, installing new seals if needed, and securing the front housing with bolts to the cylinder block, oil pan, and other parts. Timing gear alignment must also be checked during installation.
Caterpillar cat 140 h motor grader (prefix 8jm) service repair manual (8jm000...yhhjjkfkseme
This document provides instructions for removing and assembling the fuel injection pump housing and governor from a Caterpillar 3306 engine. It describes 10 steps to remove the components, including disconnecting fuel lines and other connections, removing mounting bolts and nuts, and lifting out the assembly. It then describes 8 steps to disassemble the housing further. The assembly section outlines 9 steps, including installing bearings in the proper locations and depths, inserting the camshaft, washer, and snap ring. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fusjejfskekfmsme
This document provides instructions for removing and installing a camshaft gear on a Caterpillar 3054 engine. It describes:
1) Rotating the crankshaft to align timing marks and removing the bolt and washer from the camshaft gear.
2) Using a puller tool to remove the camshaft gear and inspecting it for wear or damage.
3) Installing the camshaft gear, checking that the timing marks are aligned, and tightening the bolt.
Caterpillar cat el200 b excavator (prefix 4sg) service repair manual (4sg0000...udfjjsjkekemm
This document provides instructions for removing and installing engine accessories for an excavator model EL200B powered by an S6KT engine. It describes in detail removing components like the turbocharger, exhaust manifold, thermostat, fuel filter, injection nozzles, inlet manifold, and more. When installing accessories, it notes to follow the reverse removal procedure and ensure matching marks on gears are aligned to have the #1 piston at top dead center on compression.
The document provides instructions for removing the fuel injection pump from a 320D2 excavator with a C7.1 engine. Key steps include:
1. Turning the fuel supply and battery disconnect switch to the off position.
2. Using tools to lock the crankshaft and camshaft in position.
3. Disconnecting fuel lines from the pump and capping the lines.
4. Removing mounting bolts and carefully removing the fuel injection pump.
The document emphasizes safety precautions for working on the high pressure fuel system and provides illustrations of the pump and surrounding components.
Komatsu PC220LC-7L Excavator Service Repair Manual SN:A86001 and upudfjjsjefkkekmm
This shop manual provides instructions for servicing the PC200LC-7L and PC220LC-7L hydraulic excavators. It details removal and installation procedures for components like the radiator, hydraulic oil cooler, and engine/hydraulic pumps. Safety precautions are outlined and technicians are advised to follow the manual closely to properly service the excavators and avoid injury.
This is the Highly Detailed factory service repair manual for theCLAAS C490 CUTTER BAR, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.CLAAS C490 CUTTER BAR Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
Introduction
CCN Explanations
Safety Precautions
Gearbox / Clutch / Universal Drive Shaft
Drives
Hydraulic System
Crop Feeding
Feeder Unit
Mower Unit
Ground Guidance
Various Components / Machine Body
CCN (CLAAS Component Number)
Index
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveCLAAS C490 CUTTER BAR Service Repair Workshop Manual.
Thanks for visiting!
Liebherr r954 c 780 hydraulic excavator service repair manualudfjjsjefkkekmm
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance personnel but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn technicians of dangers.
Liebherr r944 c 1339 hydraulic excavator service repair manualudfjjsjefkkekmm
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance personnel but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn technicians of dangers.
Liebherr r934 c 1088 hydraulic excavator service repair manualudfjjsjefkkekmm
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance personnel but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn technicians of hazards.
Liebherr r934 c 918 hydraulic excavator service repair manualudfjjsjefkkekmm
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn of dangers during maintenance and repair work.
Liebherr r934 c 033 hydraulic excavator service repair manualudfjjsjefkkekmm
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance personnel but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn technicians of dangers.
Liebherr r934 c 027 hydraulic excavator service repair manualudfjjsjefkkekmm
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance personnel but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn technicians of dangers.
Liebherr r317 li tcd hydraulic excavator service repair manual serial no 3001...udfjjsjefkkekmm
This service manual provides technical information for Liebherr hydraulic excavators models A 309 - R 317 Litronic TCD. It contains sections on general information, tools, technical data, maintenance guidelines, the engine, hydraulic system, electrical system, and other major components. The manual is intended for use by customer support services and includes symbols, instructions, and tips for operating and repairing the equipment. It is copyrighted and the property of Liebherr-Hydraulikbagger GmbH.
Jcb tlt 25 g teletruk (variable reach truck)service repair manual sn 2317866 ...udfjjsjefkkekmm
This service manual provides information for servicing a Teletruk (variable reach truck). It contains sections on the machine components, including the engine. The engine section provides an overview of the 4-cylinder LPG engine and its operation. It includes descriptions of the engine components, 4-stroke operating cycle, safety information, and technical specifications. Procedures for inspection, maintenance and repair of the engine are outlined.
Jcb 560 80 tier 4 telescopic handler service repair manual sn from 2902000 on...udfjjsjefkkekmm
The document provides instructions for servicing fuel injectors and related components on JCB Loadall vehicles. It begins with an introduction to fuel injectors and their purpose. The main sections include checking injector operation using leak-off tests, removing and installing individual injectors, removing and installing injector seals, and removing and installing the common fuel rail assembly. Torque specifications are provided for reinstalling components.
Jcb 560 80 tier 4 telescopic handler service repair manual sn from 2460601 on...udfjjsjefkkekmm
This document provides service and repair instructions for fuel injectors in JCB Loadall vehicles. It describes injector components and identification, includes a check procedure using diagnostic tools, and outlines removal and installation steps. Special tools are required for tasks like leak testing and installing injector seals. Torque specifications are provided for tightening injector clamps and sleeves.
Jcb 540 170 telescopic handler service repair manualudfjjsjefkkekmm
This document provides instructions for removing and replacing front wheel axles on JCB machines. It includes warnings about safely supporting the machine before working underneath. The section describes removing the driveshaft, steering linkages, brake lines, and mounting bolts. Replacement involves reversing these steps and reconnecting lines, bleeding the brakes and steering, and checking torque settings. Specification tables list the component types and torque values.
Jcb 418 s wheeled loading shovel service repair manual (from 2335673 to 2336423)udfjjsjefkkekmm
This document provides information about identifying machines and standard torque settings for fasteners on JCB machines. It includes the following:
- Details on how to identify a machine using its identification plate and component plates including serial numbers.
- Instructions on identifying zinc plated and Dacromet fasteners and the appropriate torque settings for each.
- Tables listing torque settings for UNF and metric grade fasteners under lubricated and unlubricated conditions.
- Notes about using the correct fastener type and not interchanging zinc and Dacromet components when tightening.
Jcb 403 wheel loader service repair manual (sn 2394946 and up)udfjjsjefkkekmm
This service manual section provides information on servicing the brake system for a JCB 403 loader. It includes safety warnings and technical specifications for brake components. The manual describes the operation of the brake system and procedures for adjusting, bleeding, disassembling and assembling the brakes. Safety precautions are outlined for working with brake fluid, accumulators, and other brake components.
Jcb 320 t skid steer loader service repair manual sn from 2675500 to 2675700udfjjsjefkkekmm
The document provides instructions for removing and installing a crankshaft on an engine. Key steps include: removing components like the drive belt, pulley, oil sump, fuel injectors and rocker assembly; positioning the engine upside down; removing components attached to the crankshaft like the flywheel, gears and camshaft; and undoing and removing the main bearing caps. Cleaning and checking tolerances of the crankshaft is also described. The installation procedure is the reverse of removal and includes applying sealant and torquing bolts to the specified values.
Jcb 320 t skid steer loader service repair manual sn from 2478301 to 2478700udfjjsjefkkekmm
This service manual provides instructions for servicing JCB skid steer loaders and their components. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics and electrical system. The section summarized here provides instructions for removing and installing the crankshaft from the engine. It describes cleaning and inspecting the crankshaft, lists the required tools and consumables, and outlines the step-by-step removal and installation procedures. Precautions are given such as allowing the engine to cool before working on it and using lifting devices due to the heavy weight of components.
Jcb 67 c 1 mini excavator service repair manual (sn from 1912903 to 1913903)udfjjsjefkkekmm
This service manual provides instructions for servicing an excavator engine. It contains sections on general information, components, operation, maintenance, removal and installation procedures for the rocker and fittings assembly. The summary focuses on the rocker and fittings section, which describes the components of the rocker assembly such as the rocker arms, shaft and hydraulic tappets. It provides details on how the assembly works, lubrication system, removal and installation, disassembly/assembly, and specifications for individual components like the rocker arm, shaft, cover, and push rods.
Jcb 65 r 1 compact excavator service repair manual (sn from 1913904 to 1914244)udfjjsjefkkekmm
This service manual contains instructions for servicing and maintaining an excavator undercarriage track system. The summary includes:
1) The document provides safety warnings and technical specifications for the excavator's track system including components, construction details, and track tension specifications.
2) Instructions are given for adjusting track tension using a grease cylinder, and for removing and installing tracks, with separate procedures for steel tracks and rubber tracks.
3) Detailed steps are outlined for changing between steel and rubber tracks which involves removing/installing different components like idler wheels, rollers and recoil units to accommodate the different track types.
Jcb 57 c 1 mini excavator service repair manual (perkins engine)udfjjsjefkkekmm
This service manual section provides information on servicing the valves in the engine. It includes specifications for valve components, identification diagrams, operating principles, and procedures for checking, adjusting, and removing/installing valves. The summary covers inspecting valves for wear, adjusting valve lash, and checking valve depth using a dial indicator to ensure correct clearance and positioning below the cylinder head face.
This is the Highly Detailed factory service repair manual for theCLAAS C490 CUTTER BAR, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.CLAAS C490 CUTTER BAR Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
Introduction
CCN Explanations
Safety Precautions
Gearbox / Clutch / Universal Drive Shaft
Drives
Hydraulic System
Crop Feeding
Feeder Unit
Mower Unit
Ground Guidance
Various Components / Machine Body
CCN (CLAAS Component Number)
Index
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveCLAAS C490 CUTTER BAR Service Repair Workshop Manual.
Thanks for visiting!
Liebherr r954 c 780 hydraulic excavator service repair manualudfjjsjefkkekmm
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance personnel but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn technicians of dangers.
Liebherr r944 c 1339 hydraulic excavator service repair manualudfjjsjefkkekmm
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance personnel but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn technicians of dangers.
Liebherr r934 c 1088 hydraulic excavator service repair manualudfjjsjefkkekmm
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance personnel but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn technicians of hazards.
Liebherr r934 c 918 hydraulic excavator service repair manualudfjjsjefkkekmm
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn of dangers during maintenance and repair work.
Liebherr r934 c 033 hydraulic excavator service repair manualudfjjsjefkkekmm
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance personnel but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn technicians of dangers.
Liebherr r934 c 027 hydraulic excavator service repair manualudfjjsjefkkekmm
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance personnel but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn technicians of dangers.
Liebherr r317 li tcd hydraulic excavator service repair manual serial no 3001...udfjjsjefkkekmm
This service manual provides technical information for Liebherr hydraulic excavators models A 309 - R 317 Litronic TCD. It contains sections on general information, tools, technical data, maintenance guidelines, the engine, hydraulic system, electrical system, and other major components. The manual is intended for use by customer support services and includes symbols, instructions, and tips for operating and repairing the equipment. It is copyrighted and the property of Liebherr-Hydraulikbagger GmbH.
Jcb tlt 25 g teletruk (variable reach truck)service repair manual sn 2317866 ...udfjjsjefkkekmm
This service manual provides information for servicing a Teletruk (variable reach truck). It contains sections on the machine components, including the engine. The engine section provides an overview of the 4-cylinder LPG engine and its operation. It includes descriptions of the engine components, 4-stroke operating cycle, safety information, and technical specifications. Procedures for inspection, maintenance and repair of the engine are outlined.
Jcb 560 80 tier 4 telescopic handler service repair manual sn from 2902000 on...udfjjsjefkkekmm
The document provides instructions for servicing fuel injectors and related components on JCB Loadall vehicles. It begins with an introduction to fuel injectors and their purpose. The main sections include checking injector operation using leak-off tests, removing and installing individual injectors, removing and installing injector seals, and removing and installing the common fuel rail assembly. Torque specifications are provided for reinstalling components.
Jcb 560 80 tier 4 telescopic handler service repair manual sn from 2460601 on...udfjjsjefkkekmm
This document provides service and repair instructions for fuel injectors in JCB Loadall vehicles. It describes injector components and identification, includes a check procedure using diagnostic tools, and outlines removal and installation steps. Special tools are required for tasks like leak testing and installing injector seals. Torque specifications are provided for tightening injector clamps and sleeves.
Jcb 540 170 telescopic handler service repair manualudfjjsjefkkekmm
This document provides instructions for removing and replacing front wheel axles on JCB machines. It includes warnings about safely supporting the machine before working underneath. The section describes removing the driveshaft, steering linkages, brake lines, and mounting bolts. Replacement involves reversing these steps and reconnecting lines, bleeding the brakes and steering, and checking torque settings. Specification tables list the component types and torque values.
Jcb 418 s wheeled loading shovel service repair manual (from 2335673 to 2336423)udfjjsjefkkekmm
This document provides information about identifying machines and standard torque settings for fasteners on JCB machines. It includes the following:
- Details on how to identify a machine using its identification plate and component plates including serial numbers.
- Instructions on identifying zinc plated and Dacromet fasteners and the appropriate torque settings for each.
- Tables listing torque settings for UNF and metric grade fasteners under lubricated and unlubricated conditions.
- Notes about using the correct fastener type and not interchanging zinc and Dacromet components when tightening.
Jcb 403 wheel loader service repair manual (sn 2394946 and up)udfjjsjefkkekmm
This service manual section provides information on servicing the brake system for a JCB 403 loader. It includes safety warnings and technical specifications for brake components. The manual describes the operation of the brake system and procedures for adjusting, bleeding, disassembling and assembling the brakes. Safety precautions are outlined for working with brake fluid, accumulators, and other brake components.
Jcb 320 t skid steer loader service repair manual sn from 2675500 to 2675700udfjjsjefkkekmm
The document provides instructions for removing and installing a crankshaft on an engine. Key steps include: removing components like the drive belt, pulley, oil sump, fuel injectors and rocker assembly; positioning the engine upside down; removing components attached to the crankshaft like the flywheel, gears and camshaft; and undoing and removing the main bearing caps. Cleaning and checking tolerances of the crankshaft is also described. The installation procedure is the reverse of removal and includes applying sealant and torquing bolts to the specified values.
Jcb 320 t skid steer loader service repair manual sn from 2478301 to 2478700udfjjsjefkkekmm
This service manual provides instructions for servicing JCB skid steer loaders and their components. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics and electrical system. The section summarized here provides instructions for removing and installing the crankshaft from the engine. It describes cleaning and inspecting the crankshaft, lists the required tools and consumables, and outlines the step-by-step removal and installation procedures. Precautions are given such as allowing the engine to cool before working on it and using lifting devices due to the heavy weight of components.
Jcb 67 c 1 mini excavator service repair manual (sn from 1912903 to 1913903)udfjjsjefkkekmm
This service manual provides instructions for servicing an excavator engine. It contains sections on general information, components, operation, maintenance, removal and installation procedures for the rocker and fittings assembly. The summary focuses on the rocker and fittings section, which describes the components of the rocker assembly such as the rocker arms, shaft and hydraulic tappets. It provides details on how the assembly works, lubrication system, removal and installation, disassembly/assembly, and specifications for individual components like the rocker arm, shaft, cover, and push rods.
Jcb 65 r 1 compact excavator service repair manual (sn from 1913904 to 1914244)udfjjsjefkkekmm
This service manual contains instructions for servicing and maintaining an excavator undercarriage track system. The summary includes:
1) The document provides safety warnings and technical specifications for the excavator's track system including components, construction details, and track tension specifications.
2) Instructions are given for adjusting track tension using a grease cylinder, and for removing and installing tracks, with separate procedures for steel tracks and rubber tracks.
3) Detailed steps are outlined for changing between steel and rubber tracks which involves removing/installing different components like idler wheels, rollers and recoil units to accommodate the different track types.
Jcb 57 c 1 mini excavator service repair manual (perkins engine)udfjjsjefkkekmm
This service manual section provides information on servicing the valves in the engine. It includes specifications for valve components, identification diagrams, operating principles, and procedures for checking, adjusting, and removing/installing valves. The summary covers inspecting valves for wear, adjusting valve lash, and checking valve depth using a dial indicator to ensure correct clearance and positioning below the cylinder head face.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
2. Contact with high pressure fuel may cause fluid penetration and burn
hazards. High pressure fuel spray may cause a fire hazard. Failure to
follow these inspection, maintenance and service instructions may cause
personal injury or death.
NOTICE
Ensure that all adjustments and repairs that are carried out to the fuel
system are performed by authorized personnel that have the correct
training.
Before beginning ANY work on the fuel system, refer to Operation and
Maintenance Manual, "General Hazard Information and High
Pressure Fuel Lines" for safety information.
Refer to System Operation, Testing and Adjusting, "Cleanliness of
Fuel System Components" for detailed information on the standards of
cleanliness that must be observed during ALL work on the fuel system.
1. Turn the fuel supply to the OFF position.
2. Turn the battery disconnect switch to the OFF position.
2/5(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g02695477
3. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center position . Refer to System Operation, Testing and Adjusting, "Finding Top Center
Position for No.1 Piston" for the correct procedure.
4. Use Tooling (B) in order to lock the crankshaft so that number one piston is at top dead
center position.
5. Use Tooling (C) in order to lock the camshaft.
6. Loosen locking screw (1) . Rotate spacer (2) in order to allow locking screw (1) to tighten
against the shaft of the fuel injection pump. Rotate the fuel injection pump gear in a
counterclockwise direction in order to remove the backlash. Tighten locking screw (1) to a
torque of 15 N·m (133 lb in).
Note: Locking the screw must be tightened in order to prevent the shaft of the fuel injection
pump from rotating. The shaft of the fuel injection pump must not be rotated after the fuel
injection pump has been removed from the engine.
7. Remove the backlash from the fuel pump gear. Lock the fuel injection pump in the correct
position and remove the fuel pump gear. Refer to Disassembly and Assembly, "Fuel Pump
Gear - Remove and Install" for the correct procedure.
3/5(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 2 g02695396
8. Clean fuel injection pump (7) and the area around the fuel injection pump. Ensure that the
area is free from contamination before beginning disassembly.
9. Place a suitable container below fuel injection pump (7) in order to catch any fuel that might
be spilled.
10. Disconnect plastic tube assembly (3) , and plastic tube assembly (5) from fuel injection
pump (7) .
11. Remove plastic tube assembly (3) , and plastic tube assembly (5) from clips (4) and clip
(6) . Position the plastic tube assemblies away from the fuel injection pump.
12. Use Tooling (D) in order to plug plastic tube assembly (3) , and plastic tube assembly (5) .
13. Use Tooling (D) in order to cap connection for the plastic tube assemblies on fuel injection
pump (7) .
14. Disconnect the Original Equipment Manufactures (OEM) harness assembly from governor
(8) .
15. Disconnect the OEM harness assemblies from solenoid (9) and solenoid (10) .
16. If necessary, disconnect the OEM harness assemblies from solenoid (10) .
17. Remove the nut and bolt (11) from fuel injection pump (7) .
4/5(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 18. Remove bolt (13) and remove bracket (12) from the cylinder block and the fuel injection
pump.
Illustration 3 g02695516
19. Remove bolts (14) and sealing washers (15) from fuel injection pump (7) .
Note: The fuel injection pump should be supported by hand as the bolts are removed.
20. Carefully remove fuel injection pump (7) from front housing (16) .
21. Remove O-ring seal (17) from fuel injection pump (7) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 23 18:38:53 UTC+0800 2020
5/5(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 EXCAVATOR KBS
Configuration: 320D2 & 320D2 L Excavators KBS00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i06257875
Fuel Injection Pump - Remove - With Boost Control
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A (1)
9U-7336 Crankshaft Turning Tool 1
A (2)
5P-7305 Housing 1
5P-7305 Engine Turning Tool 1
B
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
C 230-6284 Timing Pin (Camshaft) 1
D 422-7170 Capping Kit 1
( 1 )
The Crankshaft Turning Tool is used on the front pulley.
( 2 )
This Tool is used in the aperture for the electric starting motor.
Start By:
A. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure .
B. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove" for the correct procedure.
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
1/5(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Contact with high pressure fuel may cause fluid penetration and burn
hazards. High pressure fuel spray may cause a fire hazard. Failure to
follow these inspection, maintenance and service instructions may cause
personal injury or death.
NOTICE
Ensure that all adjustments and repairs that are carried out to the fuel
system are performed by authorized personnel that have the correct
training.
Before beginning ANY work on the fuel system, refer to Operation and
Maintenance Manual, "General Hazard Information and High
Pressure Fuel Lines" for safety information.
Refer to System Operation, Testing and Adjusting, "Cleanliness of
Fuel System Components" for detailed information on the standards of
cleanliness that must be observed during ALL work on the fuel system.
1. Turn the fuel supply to the OFF position.
2. Turn the battery disconnect switch to the OFF position.
2/5(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g02791601
3. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center position . Refer to System Operation, Testing and Adjusting, "Finding Top Center
Position for No.1 Piston" for the correct procedure.
4. Use Tooling (B) in order to lock the crankshaft so that number one piston is at top dead
center position.
5. Use Tooling (C) in order to lock the camshaft.
6. Loosen locking screw (1) . Rotate spacer (2) in order to allow locking screw (1) to tighten
against the shaft of the fuel injection pump. Rotate the fuel injection pump gear in a
counterclockwise direction in order to remove the backlash. Tighten locking screw (1) to a
torque of 15 N·m (133 lb in).
Note: Locking the screw must be tightened in order to prevent the shaft of the fuel injection
pump from rotating. The shaft of the fuel injection pump must not be rotated after the fuel
injection pump has been removed from the engine.
7. Remove the backlash from the fuel pump gear. Lock the fuel injection pump in the correct
position and remove the fuel pump gear. Refer to Disassembly and Assembly, "Fuel Pump
Gear - Remove and Install" for the correct procedure.
3/5(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 2 g02791603
8. Clean fuel injection pump (8) and the area around the fuel injection pump. Ensure that the
area is free from contamination before beginning disassembly.
9. Place a suitable container below fuel injection pump (8) in order to catch any fuel that might
be spilled.
10. Disconnect plastic tube assembly (3) , plastic tube assembly (4) , and plastic tube assembly
(6) from fuel injection pump (8) .
11. Remove plastic tube assembly (3) , plastic tube assembly (4) , and plastic tube assembly (6)
from clips (5) and clip (7) . Position the plastic tube assemblies away from the fuel injection
pump.
12. Use Tooling (D) in order to plug plastic tube assembly (3) , plastic tube assembly (4) , and
plastic tube assembly (6) .
13. Use Tooling (D) in order to cap connections for the plastic tube assemblies on fuel injection
pump (8) .
14. Remove tube assembly (9) from fuel injection pump (8) and the cylinder head.
15. Remove seal (10) (not shown).
16. Disconnect the OEM harness assemblies from solenoid (11) and solenoid (12) .
17. Remove the nut and bolt (13) from fuel injection pump (8) .
4/5(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. 18. Remove bolt (15) and remove bracket (14) from the cylinder block and the fuel injection
pump.
Illustration 3 g02791604
19. Remove bolts (17) and sealing washers (16) from fuel injection pump (8) .
Note: The fuel injection pump should be supported by hand as the bolts are removed.
20. Carefully remove fuel injection pump (8) from front housing (18) .
21. Remove O-ring seal (19) from fuel injection pump (8) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 23 18:39:49 UTC+0800 2020
5/5(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 EXCAVATOR KBS
Configuration: 320D2 & 320D2 L Excavators KBS00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780451
Fuel Injection Pump - Install - With Boost Control
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
C 230-6284 Timing Pin (Camshaft) 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
NOTICE
Ensure that all adjustments and repairs that are carried out to the fuel
system are performed by authorized personnel that have the correct
training.
1/6(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Before beginning ANY work on the fuel system, refer to Operation and
Maintenance Manual, "General Hazard Information and High
Pressure Fuel Lines" for safety information.
Refer to System Operation, Testing and Adjusting, "Cleanliness of
Fuel System Components" for detailed information on the standards of
cleanliness that must be observed during ALL work on the fuel system.
1. Inspect the bore in the front housing for damage. If the bore is damaged, replace the front
housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove" for the correct
procedure.
Illustration 1 g02791604
2. Install a new O-ring seal (19) to fuel injection pump (8).
3. Install new sealing washers (16) to bolts (17).
4. Carefully install fuel injection pump (8) to front housing (18).
Note: The fuel injection pump should be supported by hand as the bolts are installed.
5. Install bolts (17) to fuel injection pump (8) hand tight.
6. Tighten bolts (17) to a torque of 22 N·m (195 lb in).
2/6(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 3 g02792516
7. Position bracket (14) onto the cylinder block and the fuel injection pump. Install bolt (15) to
the cylinder block finger tight.
8. Install the nut and bolt (13) to fuel injection pump (8) finger tight.
9. Tighten bolts (15) to a torque of 44 N·m (32 lb ft). Tighten the nut and bolt (13) to a torque
of 22 N·m (195 lb in).
Note: Ensure that the fuel injection pump is not stressed as the bolts for the bracket are
tightened.
10. Ensure that the No. 1 cylinder is at top dead center on the compression stroke. Refer to
Systems Operation, Testing and Adjusting, "Fuel Injection Timing - Check". If necessary,
use Tooling (A) in order to rotate the crankshaft so that number one piston is at the top
center position on the compression stroke. Refer to Systems Operation, Testing and
Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure.
11. Use Tooling (C) in order to lock the camshaft in the correct position. Use Tooling (B) in
order to lock the crankshaft in the correct position.
12. Install the fuel injection pump gear to fuel injection pump (8). Refer to Disassembly and
Assembly, "Fuel Injection Pump Gear - Install".
13. Remove Tooling (C) and Tooling (B).
4/6(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. 14. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Install" for the correct procedure.
15. Install a new seal (10) (not shown) to tube assembly (9).
16. Connect tube assembly (9) to fuel injection pump (8) and the cylinder head.
17. Tighten tube nut (20) to a torque of 8 N·m (71 lb in).
18. Tighten tube nut (21) to a torque of 6 N·m (53 lb in).
19. Remove the plugs from fuel injection pump (8).
20. Remove the caps from plastic tube assembly (3), plastic tube assembly (4), and plastic tube
assembly (6).
21. Connect plastic tube assembly (3), plastic tube assembly (4), and plastic tube assembly (4)
to fuel injection pump (8).
22. Install plastic tube assembly (3), plastic tube assembly (5), and plastic tube assembly (6) to
clips (5) and clip (7).
23. Connect the OEM harness assemblies to solenoid (11) and solenoid (12).
Illustration 4 g02791601
5/6(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. 24. Loosen locking screw (1). Rotate spacer (2) in order to allow locking screw (1) to tighten
against spacer (2). Tighten locking screw (1) to a torque of 12 N·m (106 lb in).
Note: Ensure that the fuel injection pump is in the unlocked position.
25. Turn the fuel supply to the OFF position.
26. Turn the battery disconnect switch to the ON position.
27. Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel
System - Prime" for the correct procedure.
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 23 18:40:44 UTC+0800 2020
6/6(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 EXCAVATOR KBS
Configuration: 320D2 & 320D2 L Excavators KBS00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780453
Fuel Injection Pump - Install - With Electronic Governor
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
C 230-6284 Timing Pin (Camshaft) 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
NOTICE
Ensure that all adjustments and repairs that are carried out to the fuel
system are performed by authorized personnel that have the correct
training.
1/5(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Before beginning ANY work on the fuel system, refer to Operation and
Maintenance Manual, "General Hazard Information and High
Pressure Fuel Lines" for safety information.
Refer to System Operation, Testing and Adjusting, "Cleanliness of
Fuel System Components" for detailed information on the standards of
cleanliness that must be observed during ALL work on the fuel system.
1. Inspect the bore in the front housing for damage. If the bore is damaged, replace the front
housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove" for the correct
procedure.
Illustration 1 g02695516
2. Install a new O-ring seal (17) to fuel injection pump (7).
3. Install new sealing washers (15) to bolts (14).
4. Carefully install fuel injection pump (7) to front housing (16).
Note: The fuel injection pump should be supported by hand as the bolts are installed.
5. Install bolts (14) to fuel injection pump (7) hand tight.
6. Tighten bolts (14) to a torque of 22 N·m (195 lb in).
2/5(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 2 g02695396
7. Position bracket (12) onto the cylinder block and the fuel injection pump. Install bolt (13) to
the cylinder block finger tight.
8. Install the nut and bolt (11) to fuel injection pump (7) finger tight.
9. Tighten bolts (13) to a torque of 44 N·m (32 lb ft). Tighten the nut and bolt (11) to a torque
of 22 N·m (195 lb in).
Note: Ensure that the fuel injection pump is not stressed as the bolts for the bracket are
tightened.
10. Ensure that the No. 1 cylinder is at top dead center on the compression stroke. Refer to
Systems Operation, Testing and Adjusting, "Fuel Injection Timing - Check". If necessary,
use Tooling (A) in order to rotate the crankshaft so that number one piston is at the top
center position on the compression stroke. Refer to Systems Operation, Testing and
Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure.
11. Use Tooling (C) in order to lock the camshaft in the correct position. Use Tooling (B) in
order to lock the crankshaft in the correct position.
12. Install the fuel injection pump gear to fuel injection pump (7). Refer to Disassembly and
Assembly, "Fuel Injection Pump Gear - Install".
13. Remove Tooling (C) and Tooling (B).
3/5(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. 14. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Install" for the correct procedure.
15. Remove the plugs from fuel injection pump (7).
16. Remove the caps from plastic tube assembly (3), and plastic tube assembly (5).
17. Connect plastic tube assembly (3), and plastic tube assembly (5) to fuel injection pump (7).
18. Install plastic tube assembly (3), and plastic tube assembly (5) to clips (4) and clip (6).
19. Connect the OEM harness assembly to governor (8).
20. Connect the OEM harness assemblies to solenoid (9) and solenoid (10).
21. If necessary, connect the OEM harness assemblies to solenoid (10).
Illustration 3 g02695477
22. Loosen locking screw (1). Rotate spacer (2) in order to allow locking screw (1) to tighten
against spacer (2). Tighten locking screw (1) to a torque of 12 N·m (106 lb in).
Note: Ensure that the fuel injection pump is in the unlocked position.
23. Turn the fuel supply to the OFF position.
24. Turn the battery disconnect switch to the ON position.
4/5(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. 25. Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel
System - Prime" for the correct procedure.
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 23 18:41:40 UTC+0800 2020
5/5(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 EXCAVATOR KBS
Configuration: 320D2 & 320D2 L Excavators KBS00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780457
Fuel Injection Pump Gear - Remove
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-7336 Crankshaft Turning Tool 1
A(2)
5P-7305 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
D - Puller (Three Leg) 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Start By:
a. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install".
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
NOTICE
1/6(W)w
2020/2/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...