The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It describes:
1) Removing the electric starting motor and flywheel before removing the flywheel housing.
2) Using tools to install lifting brackets and remove bolts securing the housing.
3) Removing the gasket and oil seal from the housing and checking dowels before installation.
4) Cleaning surfaces, installing a new gasket and oil seal, and reinstalling the housing with bolts.
Caterpillar cat 320 d l excavator (prefix fal) service repair manual (fal0000...fusjefjskekem
This document provides instructions for removing and installing various components of a Caterpillar C6.4 engine, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing just the idler gear from the front gear group.
The document includes diagrams to illustrate the procedures and lists any required tools. Removal and installation steps are provided for each component.
Caterpillar cat 320 d log loader (prefix gks) service repair manual (gks00001...ufuusefjjsekkm
This document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It outlines the required tools and steps to:
1) Remove the flywheel housing by removing bolts and lifting it off using a lifting device.
2) Use a puller tool to remove the oil seal from the housing.
3) Install a new oil seal using the puller tool.
4) Clean surfaces, install a new gasket, and reattach the housing using bolts.
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujjdfjkksekmem
This document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator. It describes how to remove and install the crankshaft rear seal using various tools. It also describes removing and installing the flywheel housing, removing the idler gear from the front gear group, and removing and installing the crankshaft front seal. The document provides detailed step-by-step instructions and illustrations for each procedure.
Caterpillar cat 320 c ln excavator (prefix axk) service repair manual (axk000...ujfjjsjekkmsmd
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator powered by a 3066 engine. It describes removing the front housing, cover, gears, seals, and spindle. It then describes installing new seals, heating components, and reinstalling gears, cover, and front housing. Removal and installation of the water pump is also described.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 ...fjkskedmme
This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Tools required are listed for each procedure.
Caterpillar cat 236 b skid steer loader (prefix hen) service repair manual (h...ufjjsjekksemmd
This document provides instructions for removing the cylinder head from a Caterpillar 236B Skid Steer Loader engine. The procedure involves draining coolant, disconnecting hoses, removing accessories attached to the head like the exhaust manifold and fuel injectors. Bolts are then loosened in a specified sequence before being removed. Lifting devices are attached to lift the heavy cylinder head off without damaging surfaces. The gasket and dowel pins are also removed.
Caterpillar cat 966 h wheel loader (prefix bs6) service repair manual (bs6000...fudjsjfekskkem
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C11 engine. It describes:
1) Using a valve spring compressor tool to remove valve locks, springs, rotators, and valves.
2) Lubricating and installing new valves, seals, springs and locks using the compressor tool.
3) To begin, the cylinder head must be removed and cleaned of contaminants before starting the valve job.
Caterpillar cat 320 d l excavator (prefix fal) service repair manual (fal0000...fusjefjskekem
This document provides instructions for removing and installing various components of a Caterpillar C6.4 engine, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing just the idler gear from the front gear group.
The document includes diagrams to illustrate the procedures and lists any required tools. Removal and installation steps are provided for each component.
Caterpillar cat 320 d log loader (prefix gks) service repair manual (gks00001...ufuusefjjsekkm
This document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It outlines the required tools and steps to:
1) Remove the flywheel housing by removing bolts and lifting it off using a lifting device.
2) Use a puller tool to remove the oil seal from the housing.
3) Install a new oil seal using the puller tool.
4) Clean surfaces, install a new gasket, and reattach the housing using bolts.
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujjdfjkksekmem
This document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator. It describes how to remove and install the crankshaft rear seal using various tools. It also describes removing and installing the flywheel housing, removing the idler gear from the front gear group, and removing and installing the crankshaft front seal. The document provides detailed step-by-step instructions and illustrations for each procedure.
Caterpillar cat 320 c ln excavator (prefix axk) service repair manual (axk000...ujfjjsjekkmsmd
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator powered by a 3066 engine. It describes removing the front housing, cover, gears, seals, and spindle. It then describes installing new seals, heating components, and reinstalling gears, cover, and front housing. Removal and installation of the water pump is also described.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 ...fjkskedmme
This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Tools required are listed for each procedure.
Caterpillar cat 236 b skid steer loader (prefix hen) service repair manual (h...ufjjsjekksemmd
This document provides instructions for removing the cylinder head from a Caterpillar 236B Skid Steer Loader engine. The procedure involves draining coolant, disconnecting hoses, removing accessories attached to the head like the exhaust manifold and fuel injectors. Bolts are then loosened in a specified sequence before being removed. Lifting devices are attached to lift the heavy cylinder head off without damaging surfaces. The gasket and dowel pins are also removed.
Caterpillar cat 966 h wheel loader (prefix bs6) service repair manual (bs6000...fudjsjfekskkem
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C11 engine. It describes:
1) Using a valve spring compressor tool to remove valve locks, springs, rotators, and valves.
2) Lubricating and installing new valves, seals, springs and locks using the compressor tool.
3) To begin, the cylinder head must be removed and cleaned of contaminants before starting the valve job.
This document is an operation and maintenance manual for McCormick tractor models. It contains sections on general information, instruments and controls, operation, maintenance and adjustments, electrical systems, specifications, hitches and implements. The manual provides instructions for identifying the tractor, engine and safety information, operating instructions, maintenance schedules and safety decals. It is intended to instruct owners and users on safe and proper operation and maintenance of the tractors.
This document provides an introduction and overview of McCormick tractors. It discusses McCormick's commitment to quality and reliability. Authorized dealers will inspect new tractors and provide training to ensure customers benefit from their machine. Regular maintenance is important for continued value, operation, and reliability of the tractor. The manual then provides a table of contents outlining the various sections contained within.
Kubota v3800 di t-e3bg diesel engine service repair manualfjjsekfxswzksmem
This document provides specifications for several Kubota diesel engine models including the V3600-E3B, V3600-T-E3B, V3800DI-T-E3B, V3300-E3BG, V3600-T-E3BG, and V3800DI-T-E3BG. It lists technical details such as the number of cylinders, displacement, power output, operating speed range, lubrication system, cooling system, and dimensions. The specifications are divided into standard engine specifications and conversion formulas.
Kioti daedong ex40 ch tractor parts catalogue manualfjjsekfxswzksmem
The document provides instructions for using a service manual for Daedong machinery. It explains that the labor hours specified were carefully set based on experienced mechanics and are meant to standardize times across skill levels and regions. It also lists several rules for selecting appropriate job codes when submitting warranty requests, such as only using one code per repair and not combining codes if one is included in another. Failure to follow the instructions could result in warranty claim rejection.
1. Read and understand the entire owner's manual before operating the tractor.
2. Only properly trained persons should operate the tractor.
3. Read and follow all warning labels and decals on the tractor.
4. Replace any missing or damaged warning decals.
5. Keep safety decals clean and free of dirt and debris.
Kioti daedong dk901 tractor parts catalogue manualfjjsekfxswzksmem
This document provides instructions and a table of contents for a tractor parts list manual. The instructions explain that the parts list is organized into groups and sub-groups with identifying codes and numbers. It also provides guidance on using the parts list for ordering parts and making repairs. The table of contents lists over 30 engine, drivetrain, and auxiliary system groups that are detailed further in the manual.
Kioti daedong dk451 tractor parts catalogue manualfjjsekfxswzksmem
This document provides instructions for using a parts list manual for tractors. It includes 10 items that describe what each section of the parts list will include such as group codes, part names, component identifiers, reference numbers, and notes. It notes that the parts list is intended to help identify correct part numbers when ordering parts and to assist with repairs by referencing illustrations. Serial numbers and interchangeability are also addressed. The document provides an overview of what information can be found in a tractor parts manual.
The document provides an overview of safety precautions for operating a KIOTI DK451/501/551 tractor. Key points include:
- Read the entire owner's manual before operating the tractor. Only properly trained persons should operate it.
- Replace any missing or damaged safety decals and keep decals clean.
- Do not operate the tractor under the influence of drugs or alcohol or while fatigued. Communicate intentions when working with other tractors.
- Never start the engine from the ground and only have the operator ride the tractor unless a passenger seat is installed.
- Use the seat belt if the tractor has a ROPS and cabin installed and never use the seat belt
Kioti daedong dk55 c tractor parts catalogue manualfjjsekfxswzksmem
This document provides instructions and information for a tractor parts list, including:
1. It outlines 10 items that provide information about how the parts list is organized and how to use it for ordering parts and making repairs.
2. It lists the table of contents which includes over 1000 part groups for the tractor, organized by system.
3. It indicates that the parts list is subject to change without notice due to continuous product improvements.
Kioti daedong dk45 sc tractor parts catalogue manualfjjsekfxswzksmem
This manual provides standard operation times for servicing jobs on Daedong tractors. It instructs technicians to use the provided job codes and times when filling out warranty forms. The times are based on average conditions and a mechanic's ability. They include preparation, inspection and spare times added to the service time. Removal and reinstallation item times cover drainage, removal, inspection/replacement, installation and testing. Conditions excluded from warranty are listed. The manual then provides an extensive table of contents and sections with job codes and times for servicing various tractor components and systems.
Kioti daedong dk35 tractor parts catalogue manualfjjsekfxswzksmem
This document is a spare parts list for DK 35-40-450L tractors. It provides information on part groups, components, references, interchangeability, and specifications for different models. The list contains details on each part, including part number, name, quantity, and remarks. It is intended to help with ordering replacement parts and repair by providing the correct part identification and specifications based on the tractor model and country. The list may be modified over time as products are continuously improved.
Bobcat 873 g series skid steer loader parts catalogue manual (sn 514240001 &a...fjjsekfxswzksmem
This document provides a parts list for a main frame that includes the part numbers, descriptions, remarks, serial numbers, and quantities of each part. Some key parts listed include the main frame, bushings, nuts, bolts, plugs, hooks, brackets, spacers, covers, blocks, guides, braces and more. The parts list is broken into several pages including for an operator cab, seat & seat bar, and seat.
The parts are for various components of a machine or vehicle including the main frame, drive train, axle, disc brakes, operator cab, seat, and seat bar. The document provides detailed information on replacement parts that would be needed to repair or replace components.
Bobcat 853 skid steer loader parts catalogue manual (sn 5102 50001 & above)fjjsekfxswzksmem
This document provides a parts list for the main frame of a machine. It includes 38 line items with descriptions of insulation crossmembers, fenders, covers, bushings, nuts, bolts, breathers, doors, seals, hooks, brackets and other parts. The serial numbers and quantities are also provided for each part listed.
Bobcat 853 skid steer loader parts catalogue manual (sn 508418001 & above )fjjsekfxswzksmem
This document contains parts lists and descriptions for various components of a vehicle. It includes sections for the main frame, operator cab, seat and seat bar. The main frame section lists 27 parts including insulation crossmembers, bushings, nuts, bolts, plugs, covers, and brackets. The operator cab section lists 33 parts such as the cab itself, hardware, insulation, seals, and manuals. The seat and seat bar section provides information on 51 parts for the seat, cushions, tracks, sensors, linkages, and safety equipment.
Bobcat 773 g series skid steer loader parts catalogue manual (sn 500 k 11001 ...fjjsekfxswzksmem
This document contains a parts list for a main frame and various components of an operator cab. It includes the part numbers, descriptions, serial numbers and quantities of 16 main frame parts and 34 operator cab parts. The parts are grouped into sections for the main frame, rear door, bolts, bushings, nuts, covers, brackets, and other components. Specifications like weld on, hinge, and serial number ranges are provided for some parts.
Bobcat 753 skid steer loader parts catalogue manual (sn 511476001 and above )fjjsekfxswzksmem
This document provides a list of parts and descriptions for the main frame, operator cab, seat and seat bar of a machine. It includes 61 references to different parts needed for these assemblies along with descriptions, remarks on usage, and serial number ranges. Key parts listed include the main frame, operator cab enclosure, seat, seat belt, pedal lock shield, and components for the seat bar and suspension. Quantities of individual parts are provided along with notes on applications based on serial number ranges.
Kioti daedong ck22 tractor parts catalogue manualfjjsekfxswzksmem
This document provides instructions for using a labor hour manual for vehicle repairs. It explains that labor hours have been precisely set by experienced mechanics and adjusted for various experience levels. It provides indexes to search for codes and outlines rules for selecting codes, such as only using one code per repair and not using subordinate codes if a higher-level code applies. Codes are also provided for diagnosis time, component mounting/dismounting, and additional time required over standard hours. Failure to follow the instructions could result in warranty claim rejection.
Bobcat 753 g series skid steer loader parts catalogue manual (g-series sn5162...fjjsekfxswzksmem
This document provides a parts list for the main frame and operator cab of an equipment. It includes over 40 parts with descriptions and identifies quantities for each. Some key parts listed are the main frame, operator cab, seat, seat bar, tracks, cushions, brackets, covers, plates, sensors, nuts, bolts, bushings and other hardware. Serial numbers are provided for some items. Remarks columns provide information on updated or replacement parts.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
This document is an operation and maintenance manual for McCormick tractor models. It contains sections on general information, instruments and controls, operation, maintenance and adjustments, electrical systems, specifications, hitches and implements. The manual provides instructions for identifying the tractor, engine and safety information, operating instructions, maintenance schedules and safety decals. It is intended to instruct owners and users on safe and proper operation and maintenance of the tractors.
This document provides an introduction and overview of McCormick tractors. It discusses McCormick's commitment to quality and reliability. Authorized dealers will inspect new tractors and provide training to ensure customers benefit from their machine. Regular maintenance is important for continued value, operation, and reliability of the tractor. The manual then provides a table of contents outlining the various sections contained within.
Kubota v3800 di t-e3bg diesel engine service repair manualfjjsekfxswzksmem
This document provides specifications for several Kubota diesel engine models including the V3600-E3B, V3600-T-E3B, V3800DI-T-E3B, V3300-E3BG, V3600-T-E3BG, and V3800DI-T-E3BG. It lists technical details such as the number of cylinders, displacement, power output, operating speed range, lubrication system, cooling system, and dimensions. The specifications are divided into standard engine specifications and conversion formulas.
Kioti daedong ex40 ch tractor parts catalogue manualfjjsekfxswzksmem
The document provides instructions for using a service manual for Daedong machinery. It explains that the labor hours specified were carefully set based on experienced mechanics and are meant to standardize times across skill levels and regions. It also lists several rules for selecting appropriate job codes when submitting warranty requests, such as only using one code per repair and not combining codes if one is included in another. Failure to follow the instructions could result in warranty claim rejection.
1. Read and understand the entire owner's manual before operating the tractor.
2. Only properly trained persons should operate the tractor.
3. Read and follow all warning labels and decals on the tractor.
4. Replace any missing or damaged warning decals.
5. Keep safety decals clean and free of dirt and debris.
Kioti daedong dk901 tractor parts catalogue manualfjjsekfxswzksmem
This document provides instructions and a table of contents for a tractor parts list manual. The instructions explain that the parts list is organized into groups and sub-groups with identifying codes and numbers. It also provides guidance on using the parts list for ordering parts and making repairs. The table of contents lists over 30 engine, drivetrain, and auxiliary system groups that are detailed further in the manual.
Kioti daedong dk451 tractor parts catalogue manualfjjsekfxswzksmem
This document provides instructions for using a parts list manual for tractors. It includes 10 items that describe what each section of the parts list will include such as group codes, part names, component identifiers, reference numbers, and notes. It notes that the parts list is intended to help identify correct part numbers when ordering parts and to assist with repairs by referencing illustrations. Serial numbers and interchangeability are also addressed. The document provides an overview of what information can be found in a tractor parts manual.
The document provides an overview of safety precautions for operating a KIOTI DK451/501/551 tractor. Key points include:
- Read the entire owner's manual before operating the tractor. Only properly trained persons should operate it.
- Replace any missing or damaged safety decals and keep decals clean.
- Do not operate the tractor under the influence of drugs or alcohol or while fatigued. Communicate intentions when working with other tractors.
- Never start the engine from the ground and only have the operator ride the tractor unless a passenger seat is installed.
- Use the seat belt if the tractor has a ROPS and cabin installed and never use the seat belt
Kioti daedong dk55 c tractor parts catalogue manualfjjsekfxswzksmem
This document provides instructions and information for a tractor parts list, including:
1. It outlines 10 items that provide information about how the parts list is organized and how to use it for ordering parts and making repairs.
2. It lists the table of contents which includes over 1000 part groups for the tractor, organized by system.
3. It indicates that the parts list is subject to change without notice due to continuous product improvements.
Kioti daedong dk45 sc tractor parts catalogue manualfjjsekfxswzksmem
This manual provides standard operation times for servicing jobs on Daedong tractors. It instructs technicians to use the provided job codes and times when filling out warranty forms. The times are based on average conditions and a mechanic's ability. They include preparation, inspection and spare times added to the service time. Removal and reinstallation item times cover drainage, removal, inspection/replacement, installation and testing. Conditions excluded from warranty are listed. The manual then provides an extensive table of contents and sections with job codes and times for servicing various tractor components and systems.
Kioti daedong dk35 tractor parts catalogue manualfjjsekfxswzksmem
This document is a spare parts list for DK 35-40-450L tractors. It provides information on part groups, components, references, interchangeability, and specifications for different models. The list contains details on each part, including part number, name, quantity, and remarks. It is intended to help with ordering replacement parts and repair by providing the correct part identification and specifications based on the tractor model and country. The list may be modified over time as products are continuously improved.
Bobcat 873 g series skid steer loader parts catalogue manual (sn 514240001 &a...fjjsekfxswzksmem
This document provides a parts list for a main frame that includes the part numbers, descriptions, remarks, serial numbers, and quantities of each part. Some key parts listed include the main frame, bushings, nuts, bolts, plugs, hooks, brackets, spacers, covers, blocks, guides, braces and more. The parts list is broken into several pages including for an operator cab, seat & seat bar, and seat.
The parts are for various components of a machine or vehicle including the main frame, drive train, axle, disc brakes, operator cab, seat, and seat bar. The document provides detailed information on replacement parts that would be needed to repair or replace components.
Bobcat 853 skid steer loader parts catalogue manual (sn 5102 50001 & above)fjjsekfxswzksmem
This document provides a parts list for the main frame of a machine. It includes 38 line items with descriptions of insulation crossmembers, fenders, covers, bushings, nuts, bolts, breathers, doors, seals, hooks, brackets and other parts. The serial numbers and quantities are also provided for each part listed.
Bobcat 853 skid steer loader parts catalogue manual (sn 508418001 & above )fjjsekfxswzksmem
This document contains parts lists and descriptions for various components of a vehicle. It includes sections for the main frame, operator cab, seat and seat bar. The main frame section lists 27 parts including insulation crossmembers, bushings, nuts, bolts, plugs, covers, and brackets. The operator cab section lists 33 parts such as the cab itself, hardware, insulation, seals, and manuals. The seat and seat bar section provides information on 51 parts for the seat, cushions, tracks, sensors, linkages, and safety equipment.
Bobcat 773 g series skid steer loader parts catalogue manual (sn 500 k 11001 ...fjjsekfxswzksmem
This document contains a parts list for a main frame and various components of an operator cab. It includes the part numbers, descriptions, serial numbers and quantities of 16 main frame parts and 34 operator cab parts. The parts are grouped into sections for the main frame, rear door, bolts, bushings, nuts, covers, brackets, and other components. Specifications like weld on, hinge, and serial number ranges are provided for some parts.
Bobcat 753 skid steer loader parts catalogue manual (sn 511476001 and above )fjjsekfxswzksmem
This document provides a list of parts and descriptions for the main frame, operator cab, seat and seat bar of a machine. It includes 61 references to different parts needed for these assemblies along with descriptions, remarks on usage, and serial number ranges. Key parts listed include the main frame, operator cab enclosure, seat, seat belt, pedal lock shield, and components for the seat bar and suspension. Quantities of individual parts are provided along with notes on applications based on serial number ranges.
Kioti daedong ck22 tractor parts catalogue manualfjjsekfxswzksmem
This document provides instructions for using a labor hour manual for vehicle repairs. It explains that labor hours have been precisely set by experienced mechanics and adjusted for various experience levels. It provides indexes to search for codes and outlines rules for selecting codes, such as only using one code per repair and not using subordinate codes if a higher-level code applies. Codes are also provided for diagnosis time, component mounting/dismounting, and additional time required over standard hours. Failure to follow the instructions could result in warranty claim rejection.
Bobcat 753 g series skid steer loader parts catalogue manual (g-series sn5162...fjjsekfxswzksmem
This document provides a parts list for the main frame and operator cab of an equipment. It includes over 40 parts with descriptions and identifies quantities for each. Some key parts listed are the main frame, operator cab, seat, seat bar, tracks, cushions, brackets, covers, plates, sensors, nuts, bolts, bushings and other hardware. Serial numbers are provided for some items. Remarks columns provide information on updated or replacement parts.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D EXCAVATOR FAL
Configuration: 320D & 320D L Excavators FAL00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742697
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
b. Remove the flywheel and ring gear. Refer to Disassembly and Assembly, "Flywheel -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Illustration 1 g01374571
1. Install Tooling (A), and a suitable lifting device onto flywheel housing (3).
2. Remove bolts (2) and the washers that secure flywheel housing (3) to the cylinder block.
3. Remove flywheel housing (3). The weight of flywheel (3) is approximately 29 kg (65 lb).
4. Remove gasket (1) (not shown).
Illustration 2 g01374572
5. Use Tooling (B) in order to remove the oil seal (4) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
NOTICE
2/4(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01374614
1. Use Tooling (B) in order to install the oil seal (4) (not shown).
Illustration 4 g01374571
2. Check the condition of two dowels (not shown). If dowels are damaged, use new parts for
replacement.
3. Clean old gasket (1) (not shown) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
4. Place flywheel housing (3) in position on the cylinder block.
5. Install the washers and bolts (2) in order to secure flywheel housing (3) to the cylinder
block.
6. Remove Tooling (A).
End By:
3/4(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 26 17:32:36 UTC+0800 2019
4/4(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D EXCAVATOR FAL
Configuration: 320D & 320D L Excavators FAL00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i06790404
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket(1)
1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Remove the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
1/4(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Illustration 1 g00604778
2. Use Tooling (B) in order to remove nut (1) and washer (2) from the threaded end of the
crankshaft.
Illustration 2 g00604784
3. Use Tooling (A) in order to remove crankshaft pulley (3) from the engine.
2/4(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Illustration 3 g00604792
4. If it is necessary to remove wear sleeve (4) from crankshaft pulley (3), use a suitable
hammer and a suitable chisel. Hold the suitable chisel at right angles to the surface of the
wear sleeve. Tap the wear sleeve in three places. You can remove the wear sleeve once the
tension is released.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 6V-9120 Socket(1)
1
C 1P-0510 Driver Gp 1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Raise the temperature of the wear sleeve. Use Tooling (C) in order to install the wear sleeve
onto the crankshaft pulley.
3/4(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 4 g01377941
2. Ensure that baffle plate (5) is oriented, as shown.
Illustration 5 g00604778
3. Position crankshaft pulley (3) onto the engine.
4. Install washer (2) and nut (1). Use Tooling (B) in order to tighten nut (1) to a torque of
707.5 ± 57.5 N·m (522 ± 42 lb ft).
5. Install the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 26 17:33:31 UTC+0800 2019
4/4(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D EXCAVATOR FAL
Configuration: 320D & 320D L Excavators FAL00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742689
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
Typical Example
1. Drill three evenly spaced 3.0 mm (0.12 inch) holes in crankshaft front seal (1).
2. Use Tooling (A) in order to remove crankshaft front seal (1). Remove the seal evenly by
alternating the position of Tooling (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 26 17:34:27 UTC+0800 2019
2/2(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D EXCAVATOR FAL
Configuration: 320D & 320D L Excavators FAL00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742692
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Illustration 1 g00612743
Typical Example
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Use Tooling (A) in order to install new crankshaft front seal (1) in the front housing.
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 26 17:35:23 UTC+0800 2019
2/2(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D EXCAVATOR FAL
Configuration: 320D & 320D L Excavators FAL00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742863
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
2/4(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. Illustration 2 g01374789
1. Remove idler gear bolt (5) and the washer from the idler gear shaft .
2. Remove thrust plate (6) from the idler gear shaft.
Illustration 3 g01374793
3. Remove idler gear (2) from the idler gear shaft.
Illustration 4 g01374804
4. If necessary, use Tooling (B) and a suitable press in order to remove bushing (7) (not
shown) from idler gear (2).
3/4(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Illustration 5 g01374810
Illustration 6 g01374811
5. The following items are components of Tooling (A).
◦ 9U-6147 Stud (9)
◦ 6V-8231 Nut (10)
◦ 9U-6146 Sleeve Assembly (11)
◦ 8T-4244 Nut (12)
6. Use Tooling (A) in order to remove idler shaft (8) (not shown) from the cylinder block.
Check idler shaft (8) for wear and damage. Replace idler shaft (8), if necessary.
Note: See the following list for the removal of the other gears in the front gear group.
◦ In order to remove camshaft gear (3), refer to Disassembly and Assembly, "Camshaft
- Remove".
◦ In order to remove fuel injection pump gear (1), refer to Disassembly and Assembly,
"Fuel Injection Pump - Remove".
◦ In order to remove the gear from the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Remove".
◦ In order to remove crankshaft gear (4), refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 26 17:36:18 UTC+0800 2019
4/4(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D EXCAVATOR FAL
Configuration: 320D & 320D L Excavators FAL00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02879402
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
a 1p-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Illustration 1 g01374804
1. Use Tooling (A) and a suitable press in order to install a new bushing (7) (not shown), if the
bushing was removed.
Illustration 2 g01374810
2. Lower the temperature of idler shaft (8) . Install idler shaft (8) (not shown) onto the cylinder
block.
Note: When idler shaft (8) is installed, ensure that the oil hole of idler shaft (8) is up.
Illustration 3 g01374827
3. Install idler gear (2) onto idler shaft (8) .
2/5(W)w
2019/11/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...