This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D and 320D L excavator. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket. The installation procedure specifies cleaning components, positioning a new gasket, and reattaching hoses and bolts in the reverse order of removal. Tools including a link bracket are listed for both removal and installation.
Caterpillar cat 320 d l 320dl excavator (prefix a6f) service repair manual (a...ufjjsjekkmdme
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320D excavator. It includes the following key details:
- Tools and parts required for the job, including a valve spring compressor and cylinder head repair stand.
- Steps to remove the cylinder head, mark valves for identification, compress springs with the tooling, and remove springs, retainers, seals and valves.
- Inspection criteria for valve and cylinder head components.
- Cleaning and lubrication requirements before installing new seals, valves, springs and retainers in reverse order of removal.
Caterpillar cat 320 d excavator (prefix mch) service repair manual (mch00001 ...ufjjsejfkskemme
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D and 320D L excavator. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket. The installation procedure specifies cleaning components, positioning a new gasket, reattaching hoses and bolts, and torquing to the specified values. Tools, safety notices, and illustrations are included to aid the process.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...ufdjjsekkmdme
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened to the specified torques, and the fuel manifold is reinstalled at the end. Separate sections provide similar instructions for removing and installing inlet and exhaust valves, and related components like valve springs. Safety notices are included throughout regarding keeping parts clean and ensuring components are properly secured.
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C7.1 engine. It describes the required tools and outlines the step-by-step process which includes positioning the piston at top dead center, compressing the valve spring with a tool, removing the valve keepers and spring, and reversing the process for installation. Safety notices are provided to wear protective equipment when working with compressed springs and ensure parts are kept clean to prevent premature wear.
1) The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D2 excavator engine.
2) It describes the required tools and outlines the step-by-step procedures for correctly positioning the piston, compressing the valve springs, and removing or installing the valve spring components.
3) Technicians are advised to take various safety precautions when working with compressed valve springs and reminded to keep all engine parts clean and free of contaminants.
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 320D excavator engine. It consists of the following steps:
1. Remove bolts and clips to detach hoses and lift the manifold off the engine using lifting brackets.
2. Clean surfaces and install a new gasket before lowering the manifold back into place and reattaching hoses and clips.
3. Tighten all bolts to the specified torques and reinstall the fuel manifold to complete the job.
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 320D excavator engine. It consists of the following steps:
1. Remove bolts and clips to detach hoses and lift the manifold off the engine using lifting brackets.
2. Clean surfaces and install a new gasket before lowering the manifold back into place and reattaching hoses and clips.
3. Tighten all bolts to the specified torques and reinstall the fuel manifold to complete the job.
Caterpillar Cat 320D L 320DL Excavator (Prefix A6F) Service Repair Manual (A6...jfkksemmdmd
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D and 320D L excavator with a C6.4 engine. The removal procedure involves using various tools to remove bolts, clips, and hoses to detach the inlet manifold. Proper lifting equipment is required due to the manifold's weight of approximately 29 kg. The installation procedure specifies cleaning components and installing new washers and bolts to reattach the inlet manifold using the same lifting equipment. Precautions are outlined to keep parts clean and torque bolts to the specified values.
Caterpillar cat 320 d l 320dl excavator (prefix a6f) service repair manual (a...ufjjsjekkmdme
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320D excavator. It includes the following key details:
- Tools and parts required for the job, including a valve spring compressor and cylinder head repair stand.
- Steps to remove the cylinder head, mark valves for identification, compress springs with the tooling, and remove springs, retainers, seals and valves.
- Inspection criteria for valve and cylinder head components.
- Cleaning and lubrication requirements before installing new seals, valves, springs and retainers in reverse order of removal.
Caterpillar cat 320 d excavator (prefix mch) service repair manual (mch00001 ...ufjjsejfkskemme
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D and 320D L excavator. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket. The installation procedure specifies cleaning components, positioning a new gasket, reattaching hoses and bolts, and torquing to the specified values. Tools, safety notices, and illustrations are included to aid the process.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...ufdjjsekkmdme
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened to the specified torques, and the fuel manifold is reinstalled at the end. Separate sections provide similar instructions for removing and installing inlet and exhaust valves, and related components like valve springs. Safety notices are included throughout regarding keeping parts clean and ensuring components are properly secured.
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C7.1 engine. It describes the required tools and outlines the step-by-step process which includes positioning the piston at top dead center, compressing the valve spring with a tool, removing the valve keepers and spring, and reversing the process for installation. Safety notices are provided to wear protective equipment when working with compressed springs and ensure parts are kept clean to prevent premature wear.
1) The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D2 excavator engine.
2) It describes the required tools and outlines the step-by-step procedures for correctly positioning the piston, compressing the valve springs, and removing or installing the valve spring components.
3) Technicians are advised to take various safety precautions when working with compressed valve springs and reminded to keep all engine parts clean and free of contaminants.
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 320D excavator engine. It consists of the following steps:
1. Remove bolts and clips to detach hoses and lift the manifold off the engine using lifting brackets.
2. Clean surfaces and install a new gasket before lowering the manifold back into place and reattaching hoses and clips.
3. Tighten all bolts to the specified torques and reinstall the fuel manifold to complete the job.
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 320D excavator engine. It consists of the following steps:
1. Remove bolts and clips to detach hoses and lift the manifold off the engine using lifting brackets.
2. Clean surfaces and install a new gasket before lowering the manifold back into place and reattaching hoses and clips.
3. Tighten all bolts to the specified torques and reinstall the fuel manifold to complete the job.
Caterpillar Cat 320D L 320DL Excavator (Prefix A6F) Service Repair Manual (A6...jfkksemmdmd
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D and 320D L excavator with a C6.4 engine. The removal procedure involves using various tools to remove bolts, clips, and hoses to detach the inlet manifold. Proper lifting equipment is required due to the manifold's weight of approximately 29 kg. The installation procedure specifies cleaning components and installing new washers and bolts to reattach the inlet manifold using the same lifting equipment. Precautions are outlined to keep parts clean and torque bolts to the specified values.
Caterpillar Cat 320D L Excavator (Prefix A6F) Service Repair Manual Instant D...udjkskdmmd
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D and 320D L excavator with a C6.4 engine. The removal procedure involves using various tools to remove bolts, clips, and hoses to detach the inlet manifold. Proper lifting equipment is required due to the manifold's weight of approximately 29 kg. The installation procedure specifies cleaning components and installing new washers before reattaching hoses and bolts with the specified torques.
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 320D excavator engine. It consists of the following steps:
1. Remove bolts and clips to detach hoses and lift the manifold off using a lifting tool.
2. Clean and position a new gasket before lowering the manifold back into place and reattaching hoses and bolts.
3. Reinstall any removed components like the air inlet heater and fuel manifold when complete.
Caterpillar Cat 320D and 320D L 320DL Excavator (Prefix A6F) Service Repair M...yan77xunhao
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 320D excavator engine. It consists of the following steps:
1. Remove bolts and clips to detach hoses and lift the manifold off the engine using lifting brackets.
2. Clean surfaces and install a new gasket before lowering the manifold back into place and reattaching hoses and clips.
3. Tighten all bolts to the specified torques once the manifold is reinstalled.
Caterpillar cat 320 d excavator (prefix mch) service repair manual (mch00001 ...yfhjsjefkksemme
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D and 320D L excavator. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket. The installation procedure specifies cleaning components, positioning a new gasket, reattaching hoses and bolts, and torquing to the specified values. Tools, safety notices, and illustrations are included to aid the process.
Caterpillar cat 320 d l excavator (prefix mch) service repair manual (mch0000...fusejkskemfm
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D and 320D L excavator. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket. The installation procedure specifies cleaning components, positioning a new gasket, reattaching hoses and bolts, and torquing to the specified values. Tools, safety notices, and illustrations are included to aid the process.
Caterpillar cat 320 d excavator (prefix mch) service repair manual (mch00001 ...fujsekfkksmemxs
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C6.4 engine.
The removal procedure involves using various tools to compress the valve springs, remove the valve keepers and spring retainer, and lift the valves out of the cylinder head. The installation procedure outlines cleaning and preparing the valve guides and stems, and using a valve spring compressor tool to carefully replace the springs, retainers and keepers in the correct orientation. Safety notices are provided to avoid injury from the compressed springs.
Caterpillar cat 320 d l excavator (prefix mch) service repair manual (mch0000...fusjefjskekmem
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D and 320D L excavator. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket. The installation procedure specifies cleaning components, positioning a new gasket, reattaching hoses and bolts, and torquing to the specified values. Tools, safety notices, and illustrations are included to aid the process.
Caterpillar cat 320 d l excavator (prefix mch) service repair manual (mch0000...jfkseksmemqw
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D excavator engine. The key steps are:
1. Remove bolts and clips to detach hoses and lift off the inlet manifold using lifting tools, as it weighs approximately 29 kg.
2. Clean and inspect gasket surfaces before installing the new gasket and inlet manifold. Attach lifting tools and position the manifold, then install bolts and clips.
3. Reattach hoses by installing new washers and bolts, and tighten bolts to the specified torques. Install the fuel manifold to complete the job.
Caterpillar cat 320 d excavator (prefix mch) service repair manual (mch00001 ...fjkskekemm
This document provides instructions for removing and installing the inlet manifold and inlet and exhaust valves on a Caterpillar C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket. Installation is the reverse process, and includes replacing washers, tightening bolts to the specified torques, and ensuring all components are clean. Removing the valves requires compressing the springs using a special tool while the piston is at top dead center. Installation involves lubricating the stems, inserting new seals, and carefully compressing the springs into place.
1. The document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR EXCAVATOR powered by a C6.4 engine.
2. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket.
3. The installation procedure specifies cleaning and preparing surfaces, positioning a new gasket, attaching hoses and bolts, and torquing bolts to the specified values.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...fujsjfkskemm
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened to the specified torques, and the fuel manifold is reinstalled at the end. Separate sections provide similar instructions for removing and installing inlet and exhaust valves, and related components like valve springs. Safety notices are included throughout regarding keeping parts clean and ensuring components are properly secured.
New holland l221 tier 4 b (final) skid steer loader service repair manual [ne...fujsjfkkskefsme
This document is a service manual for CNH Industrial America LLC 200 Series skid steer loaders and compact track loaders that meet Tier 4B and Stage IV emissions standards. It contains sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides repair and maintenance instructions for qualified dealership personnel and emphasizes using approved parts and following procedures to maintain equipment and comply with emissions regulations.
New holland cs660 combine harvesters service repair manualfujsjfkkskefsme
This repair manual provides technical information for repairing and servicing New Holland agricultural equipment models CS520, CS540, CS640, CS660, and CL560. The manual is divided into sections covering different machine systems. Sections include distribution systems, power production, power train, travelling, body and structure, tool positioning, and crop processing. Each section contains chapters that provide technical specifications, descriptions of how systems work, diagnostic information like fault codes, and procedures for removal and installation of components. Information is coded using ICE (Information, Classification, Equipment) to allow easy searching by location, type, and product model.
New holland cr8.90 combine harvesters service repair manualfujsjfkkskefsme
This document is a service manual for various combine harvester models from CNH Industrial. It contains over 20 sections that provide information on systems of the combines like the engine, transmission, axles, brakes, hydraulics, steering, tracks, electrical systems, and more. Each section includes subsections that go into further detail on specific components. The manual also includes a table linking product models to their corresponding engine.
New holland c232 stage iv compact track loader service repair manual [nfm4021...fujsjfkkskefsme
The document is a service manual that provides maintenance and repair instructions for CNH Industrial 200 Series skid steer loaders and compact track loaders with Tier 4B and Stage IV engines. It contains sections on the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and the platform, cab, bodywork and decals. The manual provides detailed procedures, part numbers, and diagrams for servicing and repairing components.
New holland l228 stage iv skid steer loader service repair manual [nfm401134 ]fujsjfkkskefsme
The document is a service manual that provides maintenance and repair instructions for CNH Industrial 200 Series skid steer loaders and compact track loaders with Tier 4B and Stage IV engines. It contains sections on the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and the platform, cab, bodywork and decals. The manual provides detailed procedures and specifications to guide qualified service technicians in servicing and repairing components of the machines.
New holland cr9.80 combine harvesters service repair manualfujsjfkkskefsme
This document is a service manual for CNH Industrial combine harvesters and covers models CX7.80 through CR10.90. It contains over 200 sections on the various systems of the combines, including the engine, transmission, hydraulics, electrical systems, attachments and more. Safety guidelines are provided at the beginning, emphasizing disengaging drives, lowering attachments and shutting off the engine before servicing.
New holland c227 tier 4 b (final) compact track loader service repair manual ...fujsjfkkskefsme
This document is a service manual for CNH Industrial America LLC 200 Series skid steer loaders and compact track loaders that meet Tier 4B and Stage IV emissions standards. It contains sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides repair and maintenance instructions for qualified dealership personnel to service these machines. It stresses the importance of only using approved parts and following procedures to maintain safe and environmentally-friendly operation.
Caterpillar cat 951 b track loader (prefix 86j) service repair manual (86j040...fujsjfkkskefsme
This document provides instructions for disassembling three types of starting motors - 37-MT, 41-MT, and 42-MT. The instructions include removing parts like the rear housing, brush holder, pinion drive housing, shift lever housing, field winding coil, and pole shoes. Detailed steps are provided with accompanying illustrations to identify each part. Cleaning and inspection procedures are described at the end.
Caterpillar cat 951 b track loader (prefix 69h) service repair manual (69h036...fujsjfkkskefsme
This document provides instructions for servicing a 951B/C track loader. It discusses general instructions for disassembly and assembly including safety, cleanliness, removal and installation of parts, cleaning and handling of parts, and reassembly. It also provides details on specific procedures like pressing parts, using bolts and applying proper torque, and installing various components like bearings, gaskets, and locks. Service tools are described and proper use of tools is emphasized for safety.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...fujsjfkkskefsme
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts and bolts, and using alignment pins to ensure proper timing when removing and installing components.
Caterpillar cat 322 l excavator (prefix 9 rl) service repair manual (9rl00001...fujsjfkkskefsme
This document provides instructions for removing and installing a governor and fuel injection control linkage on a Caterpillar 322L excavator powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and remove mounting hardware. The installation procedure specifies applying lubricant to seals, inserting linkages, and torquing bolts to the correct specifications while ensuring free movement of components. Special instructions are referenced for inspecting certain parts.
More Related Content
Similar to Caterpillar cat 320 d excavator (prefix a6f) service repair manual (a6f00001 and up)
Caterpillar Cat 320D L Excavator (Prefix A6F) Service Repair Manual Instant D...udjkskdmmd
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D and 320D L excavator with a C6.4 engine. The removal procedure involves using various tools to remove bolts, clips, and hoses to detach the inlet manifold. Proper lifting equipment is required due to the manifold's weight of approximately 29 kg. The installation procedure specifies cleaning components and installing new washers before reattaching hoses and bolts with the specified torques.
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 320D excavator engine. It consists of the following steps:
1. Remove bolts and clips to detach hoses and lift the manifold off using a lifting tool.
2. Clean and position a new gasket before lowering the manifold back into place and reattaching hoses and bolts.
3. Reinstall any removed components like the air inlet heater and fuel manifold when complete.
Caterpillar Cat 320D and 320D L 320DL Excavator (Prefix A6F) Service Repair M...yan77xunhao
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 320D excavator engine. It consists of the following steps:
1. Remove bolts and clips to detach hoses and lift the manifold off the engine using lifting brackets.
2. Clean surfaces and install a new gasket before lowering the manifold back into place and reattaching hoses and clips.
3. Tighten all bolts to the specified torques once the manifold is reinstalled.
Caterpillar cat 320 d excavator (prefix mch) service repair manual (mch00001 ...yfhjsjefkksemme
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D and 320D L excavator. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket. The installation procedure specifies cleaning components, positioning a new gasket, reattaching hoses and bolts, and torquing to the specified values. Tools, safety notices, and illustrations are included to aid the process.
Caterpillar cat 320 d l excavator (prefix mch) service repair manual (mch0000...fusejkskemfm
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D and 320D L excavator. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket. The installation procedure specifies cleaning components, positioning a new gasket, reattaching hoses and bolts, and torquing to the specified values. Tools, safety notices, and illustrations are included to aid the process.
Caterpillar cat 320 d excavator (prefix mch) service repair manual (mch00001 ...fujsekfkksmemxs
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C6.4 engine.
The removal procedure involves using various tools to compress the valve springs, remove the valve keepers and spring retainer, and lift the valves out of the cylinder head. The installation procedure outlines cleaning and preparing the valve guides and stems, and using a valve spring compressor tool to carefully replace the springs, retainers and keepers in the correct orientation. Safety notices are provided to avoid injury from the compressed springs.
Caterpillar cat 320 d l excavator (prefix mch) service repair manual (mch0000...fusjefjskekmem
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D and 320D L excavator. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket. The installation procedure specifies cleaning components, positioning a new gasket, reattaching hoses and bolts, and torquing to the specified values. Tools, safety notices, and illustrations are included to aid the process.
Caterpillar cat 320 d l excavator (prefix mch) service repair manual (mch0000...jfkseksmemqw
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 320D excavator engine. The key steps are:
1. Remove bolts and clips to detach hoses and lift off the inlet manifold using lifting tools, as it weighs approximately 29 kg.
2. Clean and inspect gasket surfaces before installing the new gasket and inlet manifold. Attach lifting tools and position the manifold, then install bolts and clips.
3. Reattach hoses by installing new washers and bolts, and tighten bolts to the specified torques. Install the fuel manifold to complete the job.
Caterpillar cat 320 d excavator (prefix mch) service repair manual (mch00001 ...fjkskekemm
This document provides instructions for removing and installing the inlet manifold and inlet and exhaust valves on a Caterpillar C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket. Installation is the reverse process, and includes replacing washers, tightening bolts to the specified torques, and ensuring all components are clean. Removing the valves requires compressing the springs using a special tool while the piston is at top dead center. Installation involves lubricating the stems, inserting new seals, and carefully compressing the springs into place.
1. The document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR EXCAVATOR powered by a C6.4 engine.
2. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket.
3. The installation procedure specifies cleaning and preparing surfaces, positioning a new gasket, attaching hoses and bolts, and torquing bolts to the specified values.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...fujsjfkskemm
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened to the specified torques, and the fuel manifold is reinstalled at the end. Separate sections provide similar instructions for removing and installing inlet and exhaust valves, and related components like valve springs. Safety notices are included throughout regarding keeping parts clean and ensuring components are properly secured.
Similar to Caterpillar cat 320 d excavator (prefix a6f) service repair manual (a6f00001 and up) (11)
New holland l221 tier 4 b (final) skid steer loader service repair manual [ne...fujsjfkkskefsme
This document is a service manual for CNH Industrial America LLC 200 Series skid steer loaders and compact track loaders that meet Tier 4B and Stage IV emissions standards. It contains sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides repair and maintenance instructions for qualified dealership personnel and emphasizes using approved parts and following procedures to maintain equipment and comply with emissions regulations.
New holland cs660 combine harvesters service repair manualfujsjfkkskefsme
This repair manual provides technical information for repairing and servicing New Holland agricultural equipment models CS520, CS540, CS640, CS660, and CL560. The manual is divided into sections covering different machine systems. Sections include distribution systems, power production, power train, travelling, body and structure, tool positioning, and crop processing. Each section contains chapters that provide technical specifications, descriptions of how systems work, diagnostic information like fault codes, and procedures for removal and installation of components. Information is coded using ICE (Information, Classification, Equipment) to allow easy searching by location, type, and product model.
New holland cr8.90 combine harvesters service repair manualfujsjfkkskefsme
This document is a service manual for various combine harvester models from CNH Industrial. It contains over 20 sections that provide information on systems of the combines like the engine, transmission, axles, brakes, hydraulics, steering, tracks, electrical systems, and more. Each section includes subsections that go into further detail on specific components. The manual also includes a table linking product models to their corresponding engine.
New holland c232 stage iv compact track loader service repair manual [nfm4021...fujsjfkkskefsme
The document is a service manual that provides maintenance and repair instructions for CNH Industrial 200 Series skid steer loaders and compact track loaders with Tier 4B and Stage IV engines. It contains sections on the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and the platform, cab, bodywork and decals. The manual provides detailed procedures, part numbers, and diagrams for servicing and repairing components.
New holland l228 stage iv skid steer loader service repair manual [nfm401134 ]fujsjfkkskefsme
The document is a service manual that provides maintenance and repair instructions for CNH Industrial 200 Series skid steer loaders and compact track loaders with Tier 4B and Stage IV engines. It contains sections on the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and the platform, cab, bodywork and decals. The manual provides detailed procedures and specifications to guide qualified service technicians in servicing and repairing components of the machines.
New holland cr9.80 combine harvesters service repair manualfujsjfkkskefsme
This document is a service manual for CNH Industrial combine harvesters and covers models CX7.80 through CR10.90. It contains over 200 sections on the various systems of the combines, including the engine, transmission, hydraulics, electrical systems, attachments and more. Safety guidelines are provided at the beginning, emphasizing disengaging drives, lowering attachments and shutting off the engine before servicing.
New holland c227 tier 4 b (final) compact track loader service repair manual ...fujsjfkkskefsme
This document is a service manual for CNH Industrial America LLC 200 Series skid steer loaders and compact track loaders that meet Tier 4B and Stage IV emissions standards. It contains sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides repair and maintenance instructions for qualified dealership personnel to service these machines. It stresses the importance of only using approved parts and following procedures to maintain safe and environmentally-friendly operation.
Caterpillar cat 951 b track loader (prefix 86j) service repair manual (86j040...fujsjfkkskefsme
This document provides instructions for disassembling three types of starting motors - 37-MT, 41-MT, and 42-MT. The instructions include removing parts like the rear housing, brush holder, pinion drive housing, shift lever housing, field winding coil, and pole shoes. Detailed steps are provided with accompanying illustrations to identify each part. Cleaning and inspection procedures are described at the end.
Caterpillar cat 951 b track loader (prefix 69h) service repair manual (69h036...fujsjfkkskefsme
This document provides instructions for servicing a 951B/C track loader. It discusses general instructions for disassembly and assembly including safety, cleanliness, removal and installation of parts, cleaning and handling of parts, and reassembly. It also provides details on specific procedures like pressing parts, using bolts and applying proper torque, and installing various components like bearings, gaskets, and locks. Service tools are described and proper use of tools is emphasized for safety.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...fujsjfkkskefsme
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts and bolts, and using alignment pins to ensure proper timing when removing and installing components.
Caterpillar cat 322 l excavator (prefix 9 rl) service repair manual (9rl00001...fujsjfkkskefsme
This document provides instructions for removing and installing a governor and fuel injection control linkage on a Caterpillar 322L excavator powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and remove mounting hardware. The installation procedure specifies applying lubricant to seals, inserting linkages, and torquing bolts to the correct specifications while ensuring free movement of components. Special instructions are referenced for inspecting certain parts.
Caterpillar cat 321 c lcr excavator (prefix mcf) service repair manual (mcf00...fujsjfkkskefsme
This document provides instructions for removing and installing the alternator, electric starting motor, and governor control motor on a Caterpillar 321C LCR excavator. The procedures describe disconnecting electrical connections, removing mounting bolts, and installing components in reverse order. Precautions like deactivating electrical systems and properly torquing bolts are noted to safely complete the work.
Caterpillar cat 428 c backhoe loader (prefix 2cr) service repair manual (2cr1...fujsjfkkskefsme
This document provides instructions for servicing an alternator and 3054 engine. It describes:
1. The alternator assembly procedure involving cleaning parts, connecting leads, installing components like the rectifier and rotor, and attaching the pulley.
2. Details about Type 1 and Type 2 3054 engine designs, including cylinder arrangements, specifications, and valve locations.
3. The procedure to remove a fuel filter base, which involves disconnecting fuel lines and removing mounting bolts.
Caterpillar cat 321 c excavator (prefix kcr) service repair manual (kcr00001 ...fujsjfkkskefsme
This document provides instructions for removing and installing various components of the heating and air conditioning system on a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent and front/rear vents
It includes detailed illustrations and step-by-step instructions for each component, as well as safety warnings about working with refrigerants. Personal protective equipment and proper refrigerant handling techniques are emphasized throughout.
Caterpillar cat 321 c excavator (prefix kbb) service repair manual (kbb00001 ...fujsjfkkskefsme
This document provides instructions for removing and installing the engine oil bypass valve and engine oil pump on a Caterpillar 321C EXCAVATOR. It describes in detail:
1) Removing the engine oil pan, threaded plug, shim, spring, and spring seat from the cylinder block to remove the oil bypass valve.
2) Removing the oil pump cover, gears, seals, and spindle to remove the oil pump. Proper cleaning and inspection of parts is emphasized.
3) Reinstalling the oil bypass valve components and oil pump by reversing the removal procedures. Heating of gears is required for installation.
Caterpillar cat 428 c backhoe loader (prefix 2cr) service repair manual (2cr1...fujsjfkkskefsme
This document provides instructions for removing and installing the fuel injection pump on a Caterpillar 3054 engine. It includes:
1) A list of required tools for the job.
2) Steps to remove the fuel injection pump by loosening a locking spacer, removing bolts, and taking off the pump.
3) Steps to install the fuel injection pump by checking the O-ring, positioning the pump, installing bolts, using a timing pin to set timing, and replacing other components.
Caterpillar cat 321 c excavator (prefix dax) service repair manual (dax00001 ...fujsjfkkskefsme
This document provides instructions for removing, disassembling, and assembling an engine oil filter base and engine oil cooler on a Caterpillar 321C excavator. The summary is:
1) The instructions describe using a strap wrench and removing bolts to detach the oil filter base and filter from the engine.
2) To disassemble the oil cooler, nuts are removed to separate the core from the cover, and gaskets are checked for wear.
3) Reassembly involves installing new gaskets on the core, securing the core to the cover with nuts, and reinstalling the assembled oil cooler.
Caterpillar cat 426 c backhoe loader (prefix 7wn) service repair manual (7wn0...fujsjfkkskefsme
This document provides instructions for servicing various components of a Caterpillar 426C BACKHOE LOADER, including removing and installing the steering cylinder, air conditioner compressor group, air conditioner filter, and full air conditioner system. Safety precautions are outlined, such as containing fluids, wearing protective equipment when working with refrigerants, and referring to additional manuals for purging and charging procedures. The procedures provide a list of removal and installation steps that include disconnecting hoses and lines, removing mounting bolts, and reversing the process for reinstallation.
Caterpillar cat 320 c excavator (prefix hbc) service repair manual (hbc00001 ...fujsjfkkskefsme
This document provides instructions for removing and installing various fuel system components on a 320C excavator with a 3066 engine. It describes removing the fuel injection pump by first removing the fuel injection lines. Several nuts, bolts, and clamps must then be removed to detach the fuel injection pump from the engine. Proper cleaning and containment of fluids is emphasized to prevent contamination.
This document provides instructions for removing and disassembling and assembling the piston pump (hydrostatic) on a 279C2 Compact Track Loader. The removal procedure involves disconnecting hoses and harness assemblies, removing mounting bolts, and lifting the pump off. The disassembly procedure involves removing valves, coils, cartridges, seals, and other components. The assembly procedure describes installing these components in reverse order and adjusting set screws to center the swashplate. Tools required include wrenches, drivers, pullers, and retaining ring pliers. Precautions are given to clean parts and plug openings to prevent contamination.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D EXCAVATOR A6F
Configuration: 320D & 320D L Excavators A6F00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02879378
Inlet Manifold - Remove and Install
SMCS - 1058-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
Start By:
A. Remove the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold (Rail) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g01375420
1. Remove bolts (1) and remove clip (2) .
Illustration 2 g01375421
2. Remove bolt (4) . Disconnect hose assembly (3) and the washers. Discard the washers.
3. Remove bolt (6) . Disconnect hose assembly (5) and the washers. Discard the washers.
Illustration 3 g01375422
2/5(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 4. Attach Tooling (A) and a suitable lifting device to inlet manifold (9) . The weight of inlet
manifold (9) is approximately 29 kg (65 lb).
5. Remove clip (7) and clip (8) .
6. Remove bolts (10) . Use Tooling (A) and the suitable lifting device in order to remove inlet
manifold (9) and the gasket.
7. If necessary, remove the air inlet heater. Refer to Disassembly and Assembly, "Air Inlet
Heater - Remove".
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Illustration 4 g01375422
1. If necessary, install the air inlet heater. Refer to Disassembly and Assembly, "Air Inlet
Heater - Install".
3/5(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 2. Attach Tooling (A) and a suitable lifting device to inlet manifold (9) . The weight of inlet
manifold (9) is approximately 29 kg (65 lb). Position the gasket. Use Tooling (A) and the
suitable lifting device in order to position inlet manifold (9) to the engine. Install bolts (10) .
Tighten bolts (10) to a torque of 18 ± 2 N·m (13 ± 1 lb ft).
3. Install clips (8) and (7) .
Illustration 5 g01375421
4. Install new washers and connect hose assembly (5) . Install bolt (6) . Tighten bolt (6) to a
torque of 34 ± 4 N·m (25 ± 3 lb ft).
5. Install new washers and connect hose assembly (3) . Install bolt (4) . Tighten bolt (4) to a
torque of 34 ± 4 N·m (25 ± 3 lb ft).
Illustration 6 g01375420
6. Install clip (2) and install bolts (1) .
End By: Install the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold (Rail) -
Install".
Tue Sep 17 09:54:27 UTC+0800 2019
4/5(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
5/5(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D EXCAVATOR A6F
Configuration: 320D & 320D L Excavators A6F00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02747674
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
B 9U-6198 Crankshaft Turning Tool 1
Start By:
a. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove".
b. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The following procedure should be adopted in order to remove the valve springs when the
cylinder head is installed to the engine.
1/6(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed.
Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder
bore.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Plug the apertures for the push rods in the cylinder head in order to
prevent the entry of loose parts into the engine.
Illustration 1 g01376301
2/6(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 2 g01376302
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
1. Install Tooling (A) into position on the cylinder head in order to compress a valve spring (4)
for the appropriate piston.
2. Use Tooling (A) in order to compress valve spring (4) and open valve (1) slightly.
Note: Do not compress valve spring (4) so that valve spring retainer (3) touches valve stem
seal (5).
3. Use Tooling (B) in order to rotate the crankshaft carefully, until the piston touches the
valve.
Note: Do not use excessive force to turn the crankshaft. The use of force can result in bent
valve stems.
4. Continue to rotate the crankshaft and gradually release the pressure on Tooling (A) until the
piston is at the top dead center position. The valve is now held in a position that allows
valve spring (4) to be safely removed.
Note: Valve springs must be replaced in pairs for the inlet valve or the exhaust valve of
each cylinder. If all valve springs require replacement the procedure can be carried out on
two cylinders at the same time. The procedure can be carried out on the following pairs of
cylinders. 1 with 6, 2 with 5 and 3 with 4. Ensure that all of the valve springs are installed
before changing from one pair of cylinders to another pair of cylinders.
3/6(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. NOTICE
Do not turn the crankshaft while the valve springs are removed.
5. Apply sufficient pressure to Tooling (A) in order to allow removal of valve keepers (2).
Note: Do not compress valve spring (4) so that valve spring retainer (3) touches valve stem
seal (5).
Remove valve keepers (2).
6. Slowly release the pressure on Tooling (A).
7. Remove valve spring retainer (3) and remove valve spring (4).
8. If necessary, remove valve stem seals (5).
9. Remove Tooling (A).
Note: The installation of each set of valve springs (4) must be completed before attempting to
remove the next set of valve springs (4).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
4/6(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 3 g01376913
Illustration 4 g01376302
1. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (5). Install new valve stem seal (5) onto the valve guide.
2. Install valve spring (4) onto the cylinder head. Position valve spring retainer (3) on valve
spring (4).
3. Install Tooling (A) in the appropriate position on the cylinder head in order to compress
valve spring (4).
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
5/6(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. 4. Apply sufficient pressure to Tooling (A) in order to install valve keepers (2). Do not
compress valve spring (4) so that valve spring retainer (3) touches valve stem seal (5).
5. Carefully release the pressure on Tooling (A).
End By:
a. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
b. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 17 09:55:23 UTC+0800 2019
6/6(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D EXCAVATOR A6F
Configuration: 320D & 320D L Excavators A6F00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i06051426
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
C 5P-1720 Seal Pick 1
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Note the location and orientation of all components for assembly purposes.
1. Clean the bottom face of the cylinder head. Check the depth of the valves below the face of
the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder
Head Valves" for the correct dimensions.
1/6(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. 2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
Illustration 1 g01376164
3. Use a suitable lifting device in order to position cylinder head (1) onto Tooling (A) with the
valve springs upward. The weight of cylinder head (1) is approximately 113 kg (250 lb).
Note: Ensure that cylinder head (1) is kept on a clean, soft surface in order to prevent
damage to the machined face.
Illustration 2 g01376174
2/6(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 3 g01376184
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Install Tooling (B) on cylinder head (1) in order to compress valve spring (5).
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
5. Apply sufficient pressure to Tooling (B) in order to remove valve keepers (3). Do not
compress the spring so that valve spring retainer (4) touches valve stem seal (6).
6. Slowly release the pressure on Tooling (B).
7. Remove valve spring retainer (4). Remove valve spring (5). Remove valve (2).
8. Use Tooling (C) in order to remove valve stem seal (6).
3/6(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. 9. Repeat Steps 4 through 7 for the remaining valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
D 312-8755 Valve Stem Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages, and all lubrication passages in the cylinder head are free from debris. Follow
Steps 1.a through 1.d in order to inspect the components of the cylinder head assembly.
Replace any components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to Testing and Adjusting,
"Cylinder Head Inspect".
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" and Testing and Adjusting, "Valve Guide - Inspect" for further
information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves ".
e. Inspect valve springs (5) for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves ".
4/6(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 4 g01376184
Illustration 5 g01376926
2. Lubricate the stem of valve (2) with clean engine oil. Install valve (2) in the appropriate
position in the cylinder head.
3. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (6). Use Tooling (C) in order to install new valve stem seal (6) onto the valve guide.
4. Install valve spring (5) onto the cylinder head. Position valve spring retainer (4) on valve
spring (5).
5. Install Tooling (B) in the appropriate position on cylinder head (1) in order to compress
valve spring (5).
Improper assembly of parts that are spring loaded can cause bodily
injury.
5/6(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
6. Apply sufficient pressure to Tooling (B) in order to install valve keepers (3). Do not
compress spring (5) so that valve spring retainer (4) touches valve stem seal (6).
7. Carefully release the pressure on Tooling (B).
8. Repeat Steps 2 through 7 for the remaining valves.
End By:
a. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 17 09:56:18 UTC+0800 2019
6/6(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D EXCAVATOR A6F
Configuration: 320D & 320D L Excavators A6F00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625003
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 384-8861 Valve Guide Remover 1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/4(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 2 g01377121
2. Use Tooling (A) in order to remove valve guides (2) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8862 Valve Guide Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/4(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 3 g01377130
1. Lubricate the outside of valve guides (2) (not shown) with clean engine oil.
2. Use Tooling (E) in order to install new valve guides (2) . Install valve guide (2) so that
valve guide (2) protrudes 16.000 mm (0.6299 inch) above Surface (X) of cylinder head (1) .
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
b. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 17 09:57:14 UTC+0800 2019
4/4(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D EXCAVATOR A6F
Configuration: 320D & 320D L Excavators A6F00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625001
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
166-7441 Valve Seat Extractor Tool 1
6V-4194 Valve Seat Extractor (1)
1
6V-4196 Valve Seat Extractor (1)
1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
( 1 )
Component of the Valve Seat Extractor Tool Group.
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Remove".
NOTICE
Keep all parts clean from contaminants.
1/5(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Contaminants may cause rapid wear and shortened component life.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B ) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B ) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/5(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 2 g01376571
2. Use the valve seat grinder of Tooling (A) in order to notch the valve seat.
Illustration 3 g01376578
3. Use the valve seat extractor of Tooling (A) to remove the inlet and exhaust valve seats.
4. Clean the valve seat in the cylinder head. Remove any rough areas from the valve seat in the
cylinder head.
5. Repeat Steps 2 through 4 for the remaining inlet valve seat inserts and exhaust valve seat
inserts.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8859 Valve Seat Installer 1
F 384-8860 Valve Seat Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Illustration 4 g01377071
Typical Example
1. Lower the temperature of the new inlet valve seat inserts (2) . Use Tooling (E) in order to
install a new inlet valve seat insert (2) (not shown) in the cylinder head.
Illustration 5 g01376588
Typical Example
2. Lower the temperature of new exhaust valve seat inserts (3) . Use Tooling (E) and Tooling
(F) in order to install the new exhaust valve seat insert (3) (not shown) in the cylinder head.
Note: The temperature of exhaust valve seat insert (3) is lowered in order to ease the
installation of exhaust valve seat insert (3) .
3. Repeat Step 1 and 2 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
b. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Install".
4/5(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 17 09:58:10 UTC+0800 2019
5/5(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D EXCAVATOR A6F
Configuration: 320D & 320D L Excavators A6F00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746253
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
a. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
30. Illustration 1 g01375410
1. Disconnect harness assembly (1).
2. Remove bolts (2) and remove engine oil cooler (3). Remove gasket (4) (not shown) from the
engine cylinder block.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 17 09:59:05 UTC+0800 2019
2/2(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
31. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D EXCAVATOR A6F
Configuration: 320D & 320D L Excavators A6F00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746254
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
a. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the
components should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly
procedures on a clean work surface. Keep components covered and protected at all times.
1/2(W)w
2019/9/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...