The document provides instructions for assembling and disassembling components of a 320C excavator travel motor. The disassembly procedure involves removing 27 individual parts from the travel motor in 28 steps. The assembly procedure instructs assembling the travel motor components in reverse order. Cleanliness is emphasized to prevent contamination of hydraulic components.
The document provides removal and installation instructions for a precooler, water temperature regulator housing, water pump, and other engine components. It includes illustrations and lists required tools. The procedures describe disconnecting hoses and harness assemblies, removing bolts and parts like housings and manifolds, and installing components in the reverse order of removal while applying sealant compounds and ensuring cleanliness. Cautions are provided about containing fluids and preventing contamination.
Caterpillar cat 320 c l 320cl excavator (prefix gla) service repair manual (...ujjdfjkskdme
The document provides instructions for disassembling a swing drive component from an excavator. It involves 29 steps, including removing gears, carriers, retaining rings, seals and other parts from the housing. Cleanliness is important to prevent contaminating the hydraulic system. Tools include retaining ring pliers, drivers and presses. The process separates all internal components to allow inspection and replacement of parts.
Caterpillar cat 345 b l excavator (prefix 9cw) service repair manual (9cw0000...fjsekdmmeed
This document provides instructions for removing and installing a cylinder head on a Caterpillar 345B L excavator engine. It details removing components like the valve mechanism cover, rocker shaft, and pushrods. It then explains how to remove the cylinder head by disconnecting sensors and tubes, and removing bolts. Reinstallation involves cleaning surfaces, installing new gaskets and seals, tightening bolts in a specific sequence, and reconnecting all removed components and hoses. Tools required are also listed.
Caterpillar cat 345 b excavator (prefix 8kw) service repair manual (8kw00001 ...fjsekdmmeed
This document provides instructions for removing and installing a cylinder head on a 345B excavator engine. It includes 14 steps to remove the head, such as removing sensors, tubes, and bolts. The 20 step installation procedure describes cleaning surfaces, installing gaskets and seals, tightening bolts in a specific sequence, and reconnecting related components like sensors and tubes. Special tools are listed for tasks like removing the fuel filter. Cautions are provided about containing fluids and keeping parts clean to prevent damage and wear.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fujsjefjkskekfm
This document provides instructions for removing and installing exhaust manifolds and air inlet manifolds on Caterpillar 3054 engines. It describes the specific removal and installation procedures for different engine types, including removing nuts/bolts, manifolds, gaskets, and related components. Proper cleaning and installation of new gaskets/sealants is emphasized to prevent contamination.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
The documents provide instructions for servicing the travel motor of a 320C excavator, including removing and installing the counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe each step in detail and include illustrations to identify the relevant components. Proper cleaning, containment of fluids, and replacement of O-rings are emphasized throughout.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...nai93qing
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
The document provides removal and installation instructions for a precooler, water temperature regulator housing, water pump, and other engine components. It includes illustrations and lists required tools. The procedures describe disconnecting hoses and harness assemblies, removing bolts and parts like housings and manifolds, and installing components in the reverse order of removal while applying sealant compounds and ensuring cleanliness. Cautions are provided about containing fluids and preventing contamination.
Caterpillar cat 320 c l 320cl excavator (prefix gla) service repair manual (...ujjdfjkskdme
The document provides instructions for disassembling a swing drive component from an excavator. It involves 29 steps, including removing gears, carriers, retaining rings, seals and other parts from the housing. Cleanliness is important to prevent contaminating the hydraulic system. Tools include retaining ring pliers, drivers and presses. The process separates all internal components to allow inspection and replacement of parts.
Caterpillar cat 345 b l excavator (prefix 9cw) service repair manual (9cw0000...fjsekdmmeed
This document provides instructions for removing and installing a cylinder head on a Caterpillar 345B L excavator engine. It details removing components like the valve mechanism cover, rocker shaft, and pushrods. It then explains how to remove the cylinder head by disconnecting sensors and tubes, and removing bolts. Reinstallation involves cleaning surfaces, installing new gaskets and seals, tightening bolts in a specific sequence, and reconnecting all removed components and hoses. Tools required are also listed.
Caterpillar cat 345 b excavator (prefix 8kw) service repair manual (8kw00001 ...fjsekdmmeed
This document provides instructions for removing and installing a cylinder head on a 345B excavator engine. It includes 14 steps to remove the head, such as removing sensors, tubes, and bolts. The 20 step installation procedure describes cleaning surfaces, installing gaskets and seals, tightening bolts in a specific sequence, and reconnecting related components like sensors and tubes. Special tools are listed for tasks like removing the fuel filter. Cautions are provided about containing fluids and keeping parts clean to prevent damage and wear.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fujsjefjkskekfm
This document provides instructions for removing and installing exhaust manifolds and air inlet manifolds on Caterpillar 3054 engines. It describes the specific removal and installation procedures for different engine types, including removing nuts/bolts, manifolds, gaskets, and related components. Proper cleaning and installation of new gaskets/sealants is emphasized to prevent contamination.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
The documents provide instructions for servicing the travel motor of a 320C excavator, including removing and installing the counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe each step in detail and include illustrations to identify the relevant components. Proper cleaning, containment of fluids, and replacement of O-rings are emphasized throughout.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...nai93qing
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...fusjekkdmdmd2w
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning components, replacing seals and filters, installing and removing parts using various tools, and precautions to take to prevent contamination of hydraulic systems.
The documents provide instructions for installing a counterbalance valve on an excavator travel motor, removing the travel motor, and disassembling and assembling the travel motor. The documents describe cleaning parts and plugging lines to prevent contamination, then list the specific steps to install, remove, and disassemble parts like seals, bolts, plates, and shafts while taking safety precautions.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning components, replacing seals and filters, installing and removing specific parts, and required tools. Safety notices are included to contain fluids, prevent contamination, and warn of spring forces.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...zoat27912076
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning components, replacing seals and filters, installing and removing parts using various tools, and precautions to take to prevent contamination of hydraulic systems.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, plates, springs, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning components, replacing seals and filters, installing and removing parts using various tools, and precautions to take to prevent contamination of hydraulic systems.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...f8skjdkdmdmd
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, plates, springs, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...fhjsekdmdm3e
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning components, replacing seals and filters, installing and removing parts using various tools, and precautions to take to prevent contamination of hydraulic systems.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning parts and containing fluids, detail the required tools, and outline the step-by-step processes for installing, removing, and disassembling/assembling various components while taking appropriate safety precautions.
The document provides instructions for assembling and disassembling components of an excavator travel motor. It includes 28 steps for disassembling the travel motor along with illustrations. The assembly procedure lists the required tools and notes that all O-rings and seals should be replaced and parts should be cleaned before assembly. It also recommends applying a light film of oil to components before assembly.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning parts and containing fluids, detail the required tools, and outline the step-by-step processes for installing, removing, and disassembling/assembling various components while taking appropriate safety precautions.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...f8usjejkdmmd
The documents provide instructions for servicing the travel motor of a 320C excavator, including removing and installing the counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe each step in detail and include illustrations to identify the relevant components. Proper cleaning, containment of fluids, and replacement of O-rings are emphasized throughout.
The document provides instructions for assembling and disassembling components of an excavator travel motor. It includes 28 steps for disassembling the travel motor along with illustrations. The assembly procedure lists the required tools and notes that all O-rings and seals should be replaced and parts should be cleaned before assembly. It also recommends applying a light film of oil to components before assembly.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning components, replacing seals and filters, installing and removing parts using various tools, and precautions to take to prevent contamination of hydraulic systems.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...8dusjkdmmdmd
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning components, replacing seals and filters, installing and removing parts using various tools, and precautions to take to prevent contamination of hydraulic systems.
New holland tj375 tractor service repair manualufjjsjekkeidol
- This document provides safety information and warnings for operating machinery.
- Operators should read the entire manual and all safety signs on the machine before operating.
- When servicing a machine, always turn off the engine, set the parking brake, remove the key and block the wheels before working on it.
- Wear proper clothing and safety equipment like a hard hat, safety shoes, gloves, and eye protection when operating machinery.
More Related Content
Similar to Caterpillar cat 320 c ln excavator (prefix jtg) service repair manual (jtg00001 and up)
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...fusjekkdmdmd2w
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning components, replacing seals and filters, installing and removing parts using various tools, and precautions to take to prevent contamination of hydraulic systems.
The documents provide instructions for installing a counterbalance valve on an excavator travel motor, removing the travel motor, and disassembling and assembling the travel motor. The documents describe cleaning parts and plugging lines to prevent contamination, then list the specific steps to install, remove, and disassemble parts like seals, bolts, plates, and shafts while taking safety precautions.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning components, replacing seals and filters, installing and removing specific parts, and required tools. Safety notices are included to contain fluids, prevent contamination, and warn of spring forces.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...zoat27912076
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning components, replacing seals and filters, installing and removing parts using various tools, and precautions to take to prevent contamination of hydraulic systems.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, plates, springs, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning components, replacing seals and filters, installing and removing parts using various tools, and precautions to take to prevent contamination of hydraulic systems.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...f8skjdkdmdmd
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, plates, springs, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...fhjsekdmdm3e
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning components, replacing seals and filters, installing and removing parts using various tools, and precautions to take to prevent contamination of hydraulic systems.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning parts and containing fluids, detail the required tools, and outline the step-by-step processes for installing, removing, and disassembling/assembling various components while taking appropriate safety precautions.
The document provides instructions for assembling and disassembling components of an excavator travel motor. It includes 28 steps for disassembling the travel motor along with illustrations. The assembly procedure lists the required tools and notes that all O-rings and seals should be replaced and parts should be cleaned before assembly. It also recommends applying a light film of oil to components before assembly.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning parts and containing fluids, detail the required tools, and outline the step-by-step processes for installing, removing, and disassembling/assembling various components while taking appropriate safety precautions.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...f8usjejkdmmd
The documents provide instructions for servicing the travel motor of a 320C excavator, including removing and installing the counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe each step in detail and include illustrations to identify the relevant components. Proper cleaning, containment of fluids, and replacement of O-rings are emphasized throughout.
The document provides instructions for assembling and disassembling components of an excavator travel motor. It includes 28 steps for disassembling the travel motor along with illustrations. The assembly procedure lists the required tools and notes that all O-rings and seals should be replaced and parts should be cleaned before assembly. It also recommends applying a light film of oil to components before assembly.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning components, replacing seals and filters, installing and removing parts using various tools, and precautions to take to prevent contamination of hydraulic systems.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...8dusjkdmmdmd
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning components, replacing seals and filters, installing and removing parts using various tools, and precautions to take to prevent contamination of hydraulic systems.
Similar to Caterpillar cat 320 c ln excavator (prefix jtg) service repair manual (jtg00001 and up) (20)
New holland tj375 tractor service repair manualufjjsjekkeidol
- This document provides safety information and warnings for operating machinery.
- Operators should read the entire manual and all safety signs on the machine before operating.
- When servicing a machine, always turn off the engine, set the parking brake, remove the key and block the wheels before working on it.
- Wear proper clothing and safety equipment like a hard hat, safety shoes, gloves, and eye protection when operating machinery.
New holland speedrower 240 tier 3 self propelled windrower service repair man...ufjjsjekkeidol
This service manual section provides specifications and repair procedures for the engine and crankcase components of the Speedrower® 200 and Speedrower® 240 self-propelled windrowers. The document covers models destined for Australia/New Zealand, Asia Pacific, Latin America, and Middle East/Africa markets, both with and without factory draper header compatibility. It addresses maintenance of the engine block, crankcase, oil pans, seals, and related parts.
Massey ferguson mf 575 tractor (gb) service parts catalogue manual (part numb...ufjjsjekkeidol
1. The document provides parts information for the cylinder block, cylinder head, crankshaft, and other components of a Massey Ferguson 575 tractor engine.
2. It includes detailed lists of each part required for the engine, including the part numbers, quantities, descriptions, and any relevant notes.
3. The parts are organized into diagrams showing their layout and assembly within the engine systems such as the cylinder head, crankshaft, timing gears, and lubrication systems.
Massey ferguson mf 560 tractor (fr) service parts catalogue manual (part numb...ufjjsjekkeidol
This document provides a parts list for the engine and accessories of a Massey Ferguson 560 tractor. It contains 75 items numbered 1 through 75 with part numbers, quantities, descriptions, and additional comments. The parts listed include the engine, cylinder block, crankshaft, cylinder head, and air induction and exhaust systems.
Massey ferguson mf 397 tractor service parts catalogue manual (part number 3...ufjjsjekkeidol
The document provides parts information for the engine of a Massey Ferguson 397 tractor. It includes 3 pages listing engine parts, their part numbers, and other identifying information. It details parts for the engine assembly, short engine, cylinder block, crankshaft and connecting rods, and cylinder head. Over 50 individual parts are specified across the various engine systems and components.
Massey ferguson mf 393 tlx tractor service parts catalogue manual (part numbe...ufjjsjekkeidol
This document provides a parts list for an MF 393 TLX tractor engine. It includes 66 items with part numbers, quantities, descriptions, and additional comments. The parts listed are for the engine block, crankshaft, pistons, connecting rods, cylinder head, and various gaskets and fasteners.
Massey ferguson mf 393 lx tractor service parts catalogue manual (part number...ufjjsjekkeidol
This document contains parts listings and descriptions for components of a Massey Ferguson 393 LX tractor engine. It includes 5 pages describing items such as the cylinder block, crankshaft, pistons, connecting rods, cylinder head, and rocker shaft assembly. Each item lists the part number, quantity, description, and any relevant comments. The purpose is to provide specifications for engine repair and ordering replacement parts.
Massey ferguson mf 390 t tractor ( b18008) service parts catalogue manual (p...ufjjsjekkeidol
This document provides part numbers and descriptions for components of a Massey Ferguson 390 T tractor engine. It includes sections on the engine installation, cylinder block, crankshaft, pistons, connecting rods, cylinder head, and rocker shaft. Each section lists the relevant part numbers, quantities, and short descriptions for repairing or replacing engine components. Serial number ranges are specified for some parts.
Massey ferguson mf 373 tractor service parts catalogue manual (part number 3...ufjjsjekkeidol
This document contains parts lists and descriptions for components of a Massey Ferguson MF 373 tractor engine. It includes lists of parts for the engine assembly, cylinder block, crankshaft and connecting rods, cylinder head, and rocker shaft. For each component, it provides the part numbers, quantities, and additional details for each part listed.
Massey ferguson mf 265 tractor (fr) service parts catalogue manual (part numb...ufjjsjekkeidol
This document provides a parts list for an MF 265 tractor engine. It contains 20 items and their corresponding part numbers needed for the engine and its components. The list includes parts for the cylinder block, crankshaft, pistons, cylinder head, flywheel, and other internal engine parts. Measurement variations or replacement part numbers are noted for some items.
Massey ferguson mf 253 tractor (it) service parts catalogue manual (part numb...ufjjsjekkeidol
This document provides a parts list and descriptions for a Massey Ferguson MF 253 tractor engine cylinder block. It includes 65 line items with part numbers, quantities, descriptions, and additional comments. The list is separated into two tables, one for the original specifications up to a certain serial number, and one for updated specifications from another serial number onward which includes some replaced or repaired parts.
Massey ferguson 7465 tractor ( tier 3 sisu engine ) service parts catalogue m...ufjjsjekkeidol
This document provides a list of parts for a Massey Ferguson 7465 tractor with a Tier 3 Sisu engine. It includes 65 line items with part numbers, quantities, descriptions, and footnote comments for engine components. The main systems covered are the engine, cylinder block, timing gear housing, crankshaft/pistons/rods, and camshaft/valve mechanism. Footnotes provide additional part number variants and application details.
Massey ferguson 6495 tractor ( dyna 6 tier 3 ) service parts catalogue manua...ufjjsjekkeidol
This document provides part numbers and descriptions for components of the crankshaft, pistons, and connecting rods of a Massey Ferguson 6495 tractor engine. It lists 51 individual parts, including the crankshaft, pistons, connecting rods, bearings, thrust washers, screws, and rings. Footnotes provide additional details on some part numbers and applicability based on the engine serial number.
Massey ferguson 6475 tractor (tier 3 sisu engine) service parts catalogue man...ufjjsjekkeidol
This document provides exploded view diagrams and part lists for the engine and various engine components of a Massey Ferguson 6475 tractor with a Tier 3 Sisu engine. The first section lists 35 parts for the overall engine assembly. Subsequent sections detail parts for the cylinder block, timing gear housing, crankshaft, pistons and connecting rods, camshaft and valve mechanism, and other engine subassemblies. Each item is accompanied by part number, quantity, description, and footnote comments for some parts.
Massey ferguson 6465 tractor (tier 3 perkins engine) service parts catalogue...ufjjsjekkeidol
This document provides part numbers and descriptions for components of a Massey Ferguson 6465 tractor with a Tier 3 Perkins engine. It includes lists of parts for the engine and its various subassemblies such as the cylinder block, cylinder head, camshaft, crankshaft, and rocker arm. Footnotes provide additional details on some part numbers. The lists contain over 40 individual part items in total.
This document provides instructions for disassembling, cleaning, inspecting, and reassembling an idler wheel for an excavator model E240. The disassembly process involves removing the tapered plug, spring pins, seals, bushing, and other components from the wheel, bearing, and shaft. Parts are then cleaned using kerosene and rinsed. Reassembly follows the reverse order of disassembly. The document also provides standards for repairing the wheel through welding, storage of parts, and preventing internal rust.
This document provides instructions for disassembling, cleaning, inspecting, and reassembling an idler wheel for an excavator model E240. The disassembly process involves removing the tapered plug, spring pins, seals, bushing, and other components from the wheel, bearing, and shaft. Parts are then cleaned using kerosene and rinsed. Reassembly follows the reverse order of disassembly. The document also provides standards for repairing the wheel through welding, storage of parts, and preventing internal rust.
Caterpillar cat 322 b l excavator (prefix 1ys) service repair manual (1ys0000...ufjjsjekkeidol
This document provides instructions for removing and installing a governor and fuel injection control linkage on a Caterpillar 3116 engine. The removal procedure involves disconnecting linkages, removing clips and pins to detach the governor. Installation requires cleaning and lubricating seals, reattaching the governor with pins and clips, and reconnecting linkages. Tools including special pliers and pins are required.
Caterpillar cat 322 b l excavator (prefix 1as) service repair manual (1as0000...ufjjsjekkeidol
The document provides instructions for removing and installing a governor from a 3116 diesel engine. It describes:
1) Removing the governor by disconnecting linkages, tubes, and clips then removing mounting bolts. O-rings must also be removed from the governor and cylinder head.
2) Installing the governor requires replacing the O-rings, reconnecting linkages and tubes using special tools, and adjusting fuel settings after installation.
3) Additional documents are referenced for more information on governor inspection, testing, and components. Precautions are provided to keep parts clean and contain fluids during the process.
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressionsVictor Morales
K8sGPT is a tool that analyzes and diagnoses Kubernetes clusters. This presentation was used to share the requirements and dependencies to deploy K8sGPT in a local environment.
Embedded machine learning-based road conditions and driving behavior monitoringIJECEIAES
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
We have compiled the most important slides from each speaker's presentation. This year’s compilation, available for free, captures the key insights and contributions shared during the DfMAy 2024 conference.
International Conference on NLP, Artificial Intelligence, Machine Learning an...gerogepatton
International Conference on NLP, Artificial Intelligence, Machine Learning and Applications (NLAIM 2024) offers a premier global platform for exchanging insights and findings in the theory, methodology, and applications of NLP, Artificial Intelligence, Machine Learning, and their applications. The conference seeks substantial contributions across all key domains of NLP, Artificial Intelligence, Machine Learning, and their practical applications, aiming to foster both theoretical advancements and real-world implementations. With a focus on facilitating collaboration between researchers and practitioners from academia and industry, the conference serves as a nexus for sharing the latest developments in the field.
CHINA’S GEO-ECONOMIC OUTREACH IN CENTRAL ASIAN COUNTRIES AND FUTURE PROSPECTjpsjournal1
The rivalry between prominent international actors for dominance over Central Asia's hydrocarbon
reserves and the ancient silk trade route, along with China's diplomatic endeavours in the area, has been
referred to as the "New Great Game." This research centres on the power struggle, considering
geopolitical, geostrategic, and geoeconomic variables. Topics including trade, political hegemony, oil
politics, and conventional and nontraditional security are all explored and explained by the researcher.
Using Mackinder's Heartland, Spykman Rimland, and Hegemonic Stability theories, examines China's role
in Central Asia. This study adheres to the empirical epistemological method and has taken care of
objectivity. This study analyze primary and secondary research documents critically to elaborate role of
china’s geo economic outreach in central Asian countries and its future prospect. China is thriving in trade,
pipeline politics, and winning states, according to this study, thanks to important instruments like the
Shanghai Cooperation Organisation and the Belt and Road Economic Initiative. According to this study,
China is seeing significant success in commerce, pipeline politics, and gaining influence on other
governments. This success may be attributed to the effective utilisation of key tools such as the Shanghai
Cooperation Organisation and the Belt and Road Economic Initiative.
6th International Conference on Machine Learning & Applications (CMLA 2024)ClaraZara1
6th International Conference on Machine Learning & Applications (CMLA 2024) will provide an excellent international forum for sharing knowledge and results in theory, methodology and applications of on Machine Learning & Applications.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR JTG
Configuration: 320C, 320C L, 320C LN Excavators JTG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i02334471
Counterbalance Valve (Travel) - Install
SMCS - 5111; 5811-012-KV
Installation Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
1/3(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Illustration 1 g00651063
1. Install new O-ring seals (5) and (6).
Illustration 2 g01021074
2. Position counterbalance valve (1) on the travel motor.
3. Install bolts (2). Tighten bolts (2) to a torque of 80 ± 8 N·m (59 ± 6 lb ft).
Note: Replace the O-ring face seals in the hose assemblies.
4. Install the split flanges and bolts (3) in order to connect hose assemblies (4).
5. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
6. Check the hydraulic oil level.
2/3(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Reference: Refer to Operation and Maintenance Manual, "Hyrdaulic System Oil Level -
Check" for the correct filling procedure.
End By:
a. Install the travel motor guard. Refer to Disassembly and Assembly, "Travel Motor Guard -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 28 13:14:15 UTC+0800 2019
3/3(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR JTG
Configuration: 320C, 320C L, 320C LN Excavators JTG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i03524303
Travel Motor - Remove
SMCS - 4351-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded RodM16x381 mm 15 inch 2
Start By:
A. Remove the counterbalance valve. Refer to Disassembly and Assembly, "Counterbalance
Valve (Travel) - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
1. Drain the oil from the final drive into a suitable container for storage or disposal.
Illustration 1 g00707275
2. Disconnect hose assemblies (1) and (3) . Remove two bolts (2) .
2/3(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Illustration 2 g00944825
3. Install Tooling (A) in the place of bolts (2) .
4. Remove remaining bolt (2A) that secures travel motor (4) to the final drive.
Illustration 3 g00707267
5. Attach a suitable lifting device to travel motor (4) . The weight of travel motor (4) is
approximately 57 kg (125 lb). Carefully pull travel motor (4) out of the final drive.
Illustration 4 g00651795
6. Remove O-ring seal (5) from the travel motor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 28 13:15:11 UTC+0800 2019
3/3(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR JTG
Configuration: 320C, 320C L, 320C LN Excavators JTG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i01959727
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0074 Slide Hammer 1
C 9S-9152 Bearing Puller 1
D
1U-9895 Crossblock 1
3H-0465 Push-Puller Plate 2
8T-0649 Bolt 2
9X-8257 Washer 2
E 5P-0975 Plate 1
Start By:
a. Remove the piston motor (travel). Refer to Disassembly and Assembly, "Piston Motor
(Travel) - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/12(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on the motor and on all hose assemblies for installation purposes
and for the purpose of orientation. Plug all hose assemblies. This will help to prevent fluid loss
and this helps to keep contaminants from entering the system.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g00779154
1. Remove bolts (1).
Illustration 2 g00779159
2/12(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. 2. Remove bolts (2) from the traction control valve in order to install Tooling (A).
Illustration 3 g00779163
3. Remove traction control valve (3) and travel motor (4) from the final drive.
Illustration 4 g00779215
4. Remove Tooling (A). Remove four bolts (2). Remove traction control valve (3).
Illustration 5 g01018464
5. Remove socket head bolts (5). Remove O-ring seal (6) and O-ring seals (7). Remove head
(8).
3/12(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Illustration 9 g01018466
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove adapter (14) and the O-ring seal. Remove spool (13) and spring (12) from head (8).
Illustration 10 g00779279
10. Remove washer set (15).
5/12(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Illustration 11 g00779289
11. Remove port plate (16).
Illustration 12 g00780482
Illustration 13 g01020385
12. Remove three small O-ring seals (17). Install Tooling (D) and Tooling (E), as shown.
Tooling (E) provides a protective cover for the barrel assembly. Tooling (E) prevents
Tooling (D) from damaging the surface of the barrel assembly.
6/12(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. 13. Retain piston (18) with Tooling (D) and apply approximately 517 kPa (75 psi) of shop air
pressure to brake release port (Y). Brake piston (18) will move out of the piston guide.
Remove brake piston (18) from the main housing.
Illustration 14 g00779307
14. Remove O-ring seal (19) and the backup ring and remove O-ring seal (20) and the backup
ring.
Illustration 15 g00779310
15. Remove piston guide (21). Remove O-ring seal (22).
Illustration 16 g00779341
7/12(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. 16. Remove O-ring seal (23) and backup ring (24).
Illustration 17 g00779343
17. Lay the travel motor housing on one side in order to remove rotating group (25) and brake
pack (26) as a unit.
Illustration 18 g00780107
18. Remove brake pack (26).
Illustration 19 g00780290
8/12(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. NOTICE
In order to ensure that each piston assembly is installed into its original
bore, identify and mark each piston assembly, retaining plate and the
barrel before removing the piston assembly.
To avoid damage to the barrel assembly parts, do not allow the parts to
separate from the assembly during removal or installation.
19. Remove pistons (27) and retainer plate (28) from barrel (29) as a unit. Separate the pistons
from the retainer plate.
Illustration 20 g00780317
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
20. Remove guide (30), spacer (31), and nine springs (32) from the barrel.
9/12(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. Illustration 21 g00780328
21. Remove swashplate (33).
Illustration 22 g00780348
22. Use a magnet in order to remove keys (34) and pistons (35).
Illustration 23 g00780352
23. Use a magnet in order to remove pins (36).
10/12(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Illustration 24 g00780345
24. Remove shaft assembly (37). Remove plugs (38) and the O-ring seals.
Illustration 25 g01020388
25. Use Tooling (B) in order to remove seal (39).
Illustration 26 g00780494
26. Remove retaining rings (40) from each side of the bearing.
11/12(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. Illustration 27 g00780502
27. Use a suitable press in order to remove bearing assembly (41) from shaft (42).
Illustration 28 g00780544
28. Use a suitable press and Tooling (C) in order to remove inner race (43) from shaft (42).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 28 13:16:07 UTC+0800 2019
12/12(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR JTG
Configuration: 320C, 320C L, 320C LN Excavators JTG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i01959745
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
F 1P-0510 Driver Group 1
G 206-3689 Turning Tool 1
H 5P-0960 Molybdenum Grease 1
Note: Replace all O-ring seals and gaskets. Apply a light film of "10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/13(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. Illustration 1 g00780677
1. Raise the temperature of inner race (43). Lower the temperature of shaft (42). Use a soft
hammer in order to install inner race (43) on shaft (42).
Illustration 2 g00780698
2. Raise the temperature of bearing assembly (41). Lower the temperature of shaft (42). Install
bearing assembly (41) on shaft (42).
Illustration 3 g00780494
3. Install retaining rings (40) on each side of the bearing.
2/13(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. Illustration 4 g01018474
4. Use Tooling (F) in order to install seal (39).
Illustration 5 g00780715
5. Use a soft hammer in order to install shaft assembly (37).
Illustration 6 g00780723
6. Install plugs (38) and the O-ring seals. Tighten plugs (38) to a torque of 140 ± 14 N·m
(103 ± 10 lb ft).
3/13(W)w
2019/10/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...