This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator powered by a 3066 engine. It describes removing the front housing, cover, gears, seals, and spindle. It then describes installing these components in reverse order, including heating some parts for easier installation. Precautions are provided regarding cleaning, fluids, and personal protective equipment.
Caterpillar cat 320 c ln excavator (prefix axk) service repair manual (axk000...ujfjjsjekkmsmd
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator powered by a 3066 engine. It describes removing the front housing, cover, gears, seals, and spindle. It then describes installing new seals, heating components, and reinstalling gears, cover, and front housing. Removal and installation of the water pump is also described.
Caterpillar cat 966 h wheel loader (prefix bs6) service repair manual (bs6000...fudjsjfekskkem
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C11 engine. It describes:
1) Using a valve spring compressor tool to remove valve locks, springs, rotators, and valves.
2) Lubricating and installing new valves, seals, springs and locks using the compressor tool.
3) To begin, the cylinder head must be removed and cleaned of contaminants before starting the valve job.
Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 ...fjkskedmme
This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Tools required are listed for each procedure.
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujjdfjkksekmem
This document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator. It describes how to remove and install the crankshaft rear seal using various tools. It also describes removing and installing the flywheel housing, removing the idler gear from the front gear group, and removing and installing the crankshaft front seal. The document provides detailed step-by-step instructions and illustrations for each procedure.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
Caterpillar cat 320 d log loader (prefix gks) service repair manual (gks00001...ufuusefjjsekkm
This document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It outlines the required tools and steps to:
1) Remove the flywheel housing by removing bolts and lifting it off using a lifting device.
2) Use a puller tool to remove the oil seal from the housing.
3) Install a new oil seal using the puller tool.
4) Clean surfaces, install a new gasket, and reattach the housing using bolts.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
Caterpillar cat 320 c ln excavator (prefix axk) service repair manual (axk000...ujfjjsjekkmsmd
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator powered by a 3066 engine. It describes removing the front housing, cover, gears, seals, and spindle. It then describes installing new seals, heating components, and reinstalling gears, cover, and front housing. Removal and installation of the water pump is also described.
Caterpillar cat 966 h wheel loader (prefix bs6) service repair manual (bs6000...fudjsjfekskkem
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C11 engine. It describes:
1) Using a valve spring compressor tool to remove valve locks, springs, rotators, and valves.
2) Lubricating and installing new valves, seals, springs and locks using the compressor tool.
3) To begin, the cylinder head must be removed and cleaned of contaminants before starting the valve job.
Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 ...fjkskedmme
This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Tools required are listed for each procedure.
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujjdfjkksekmem
This document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator. It describes how to remove and install the crankshaft rear seal using various tools. It also describes removing and installing the flywheel housing, removing the idler gear from the front gear group, and removing and installing the crankshaft front seal. The document provides detailed step-by-step instructions and illustrations for each procedure.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
Caterpillar cat 320 d log loader (prefix gks) service repair manual (gks00001...ufuusefjjsekkm
This document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It outlines the required tools and steps to:
1) Remove the flywheel housing by removing bolts and lifting it off using a lifting device.
2) Use a puller tool to remove the oil seal from the housing.
3) Install a new oil seal using the puller tool.
4) Clean surfaces, install a new gasket, and reattach the housing using bolts.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator. The removal procedure involves taking off the front housing, cover, gears, seals and spindle. The installation procedure specifies heating some components, using tools to press in seals and gears, and ensuring proper alignment and torque of fasteners. Proper cleaning and containment of fluids is emphasized.
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator. It describes:
1. Removing the front housing, cover, gears, seals, and spindle to access the oil pump.
2. Using tools like a puller and driver to remove specific components.
3. Installing the spindle, gears, seals, cover, and front housing, ensuring clean surfaces and applying the correct torque.
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 320C LN excavator. It outlines 10 steps to remove the pump, including removing the front housing, cover, gears, seals and spindle. It then outlines 8 steps to install the pump, including heating components, installing seals, gears and the cover. Safety notices are provided regarding keeping components clean and containing fluids.
The document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D excavator. It includes 6 steps to remove the oil pump, requiring various tools. The oil pump installation has 6 steps as well, including heating components to aid installation. The water pump removal requires 3 steps including removing bolts and the pump. The water pump disassembly has 6 steps after heating the pump. Reassembly of the water pump lists 7 steps including installing seals and bearings using press tools.
The document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D excavator. It describes in step-by-step detail how to disassemble, remove, and install each component while maintaining cleanliness and containing fluids. Tools required are listed for each procedure.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to clean and lubricate the parts before reinstalling them in reverse order. Proper use of tooling is emphasized to safely compress springs during the process.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to prepare and install the components in reverse order. Safety notices are included regarding preventing contamination and injury from parts under spring pressure.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to prepare and install the components in reverse order. Safety notices are included regarding preventing contamination and injury from parts under spring pressure.
The document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump of a Caterpillar 320D LRR excavator. The oil pump removal instructions describe removing covers, gears, and other components. The water pump instructions describe removing the pump, pulley, and disassembling internal components like bearings and seals. Reassembly and installation procedures are also provided.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like gears, covers, and seals. Detailed illustrations and cautions about cleaning and containing fluids are provided. Components are to be checked for wear and replaced as needed during disassembly and reassembly.
The document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump of a Caterpillar 320D LRR excavator. The oil pump removal instructions describe removing covers, gears, and other components. The water pump instructions describe removing the pump, pulley, and disassembling internal components like bearings and seals. Reassembly and installation procedures are also provided.
Caterpillar Cat 320C U, 320C LU Excavator (Prefix CLM) Service Repair Manual ...ze6074xunong
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...fusjekkdmdmd2w
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then guide reversing the disassembly process, noting the importance of cleanliness and replacing worn parts. Proper bearing installation and alignment of gears and shafts is emphasized.
3. Additional documents cover removing and installing the assembled auxiliary pump drive group and performing maintenance on other excavator systems.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...fusjekkdmdmd2w
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, bearings and seals.
2. The assembly instructions then guide rebuilding the pump drive group, including pressing in new bearings, installing seals and covers, and reassembling the shafts and gears.
3. Cleanliness is emphasized throughout to prevent contamination of hydraulic systems.
Caterpillar Cat 320C U, 320C LU Excavator (Prefix CLM) Service Repair Manual ...f8usejkdmmd8i
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...fusjekdkmd8ddjd
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then guide reversing the disassembly process, noting the importance of cleanliness and replacing worn parts. Proper bearing installation and alignment of gears and shafts is emphasized.
3. The overall purpose is to repair or replace internal components while preventing contamination of the hydraulic system.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...f8ujkskdmdm
The document provides step-by-step instructions to disassemble and assemble the auxiliary pump drive group of an excavator. It details removing covers, shafts, gears, seals, and bearings during disassembly. The assembly section instructs lowering bearing temperatures and installing components in reverse order while applying sealant. Cleanliness is emphasized throughout to prevent contamination of hydraulic systems.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...f8ujkskdmdm
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then detail how to install the bearings at the proper temperatures and reassemble the components in reverse order.
3. Proper cleaning and replacement of seals is emphasized to prevent contamination of hydraulic systems.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...fusjekdkmd8ddjd
This document provides instructions for disassembling and assembling the auxiliary pump drive of an excavator. It begins with safety notices and a list of required tools. The disassembly steps include removing alignment pins, bolts, covers, seals, shafts, gears, and bearings from the pump drive body. The assembly steps list installing these components in reverse order, noting the importance of cleanliness and replacing seals. Torque and heating specifications are provided for installing bearings. The process is completed by reinstalling the auxiliary pump drive.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...zoat27912076
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
New holland cx6080 tier 3 combine harvester service repair manualujfdjdjfkjksk
The document is a service manual that provides information on hydraulic, pneumatic, electrical, and electronic systems for CX5000 and CX6000 series equipment. It includes:
- Specifications and torque values for hydraulic fittings and connections
- Details on the primary hydraulic power system, including locations and functions of key components like pumps, valves, cylinders, and reservoirs
- Schematics and diagrams showing hydraulic system layout and component locations
The manual provides technical data, descriptions of functionality, and service information on critical fluid power and electrical systems to support maintenance and repair of the equipment.
New holland cx6080 cx6090 tier 4 combine harvester service repair manualujfdjdjfkjksk
The document is a service manual that provides information on hydraulic, pneumatic, electrical and electronic systems for CX5000 and CX6000 series equipment. It includes:
- Specifications and torque values for hydraulic fittings and connections.
- Details of the primary hydraulic system including three hydraulic pumps that power different circuits.
- A hydraulic schematic showing the layout of components in the hydraulic system.
- Images and descriptions locating hydraulic components on the front of the machine.
More Related Content
Similar to Caterpillar cat 320 c ln excavator (prefix axk) service repair manual (axk00001 and up)
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator. The removal procedure involves taking off the front housing, cover, gears, seals and spindle. The installation procedure specifies heating some components, using tools to press in seals and gears, and ensuring proper alignment and torque of fasteners. Proper cleaning and containment of fluids is emphasized.
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator. It describes:
1. Removing the front housing, cover, gears, seals, and spindle to access the oil pump.
2. Using tools like a puller and driver to remove specific components.
3. Installing the spindle, gears, seals, cover, and front housing, ensuring clean surfaces and applying the correct torque.
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 320C LN excavator. It outlines 10 steps to remove the pump, including removing the front housing, cover, gears, seals and spindle. It then outlines 8 steps to install the pump, including heating components, installing seals, gears and the cover. Safety notices are provided regarding keeping components clean and containing fluids.
The document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D excavator. It includes 6 steps to remove the oil pump, requiring various tools. The oil pump installation has 6 steps as well, including heating components to aid installation. The water pump removal requires 3 steps including removing bolts and the pump. The water pump disassembly has 6 steps after heating the pump. Reassembly of the water pump lists 7 steps including installing seals and bearings using press tools.
The document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D excavator. It describes in step-by-step detail how to disassemble, remove, and install each component while maintaining cleanliness and containing fluids. Tools required are listed for each procedure.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to clean and lubricate the parts before reinstalling them in reverse order. Proper use of tooling is emphasized to safely compress springs during the process.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to prepare and install the components in reverse order. Safety notices are included regarding preventing contamination and injury from parts under spring pressure.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to prepare and install the components in reverse order. Safety notices are included regarding preventing contamination and injury from parts under spring pressure.
The document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump of a Caterpillar 320D LRR excavator. The oil pump removal instructions describe removing covers, gears, and other components. The water pump instructions describe removing the pump, pulley, and disassembling internal components like bearings and seals. Reassembly and installation procedures are also provided.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like gears, covers, and seals. Detailed illustrations and cautions about cleaning and containing fluids are provided. Components are to be checked for wear and replaced as needed during disassembly and reassembly.
The document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump of a Caterpillar 320D LRR excavator. The oil pump removal instructions describe removing covers, gears, and other components. The water pump instructions describe removing the pump, pulley, and disassembling internal components like bearings and seals. Reassembly and installation procedures are also provided.
Caterpillar Cat 320C U, 320C LU Excavator (Prefix CLM) Service Repair Manual ...ze6074xunong
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...fusjekkdmdmd2w
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then guide reversing the disassembly process, noting the importance of cleanliness and replacing worn parts. Proper bearing installation and alignment of gears and shafts is emphasized.
3. Additional documents cover removing and installing the assembled auxiliary pump drive group and performing maintenance on other excavator systems.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...fusjekkdmdmd2w
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, bearings and seals.
2. The assembly instructions then guide rebuilding the pump drive group, including pressing in new bearings, installing seals and covers, and reassembling the shafts and gears.
3. Cleanliness is emphasized throughout to prevent contamination of hydraulic systems.
Caterpillar Cat 320C U, 320C LU Excavator (Prefix CLM) Service Repair Manual ...f8usejkdmmd8i
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...fusjekdkmd8ddjd
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then guide reversing the disassembly process, noting the importance of cleanliness and replacing worn parts. Proper bearing installation and alignment of gears and shafts is emphasized.
3. The overall purpose is to repair or replace internal components while preventing contamination of the hydraulic system.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...f8ujkskdmdm
The document provides step-by-step instructions to disassemble and assemble the auxiliary pump drive group of an excavator. It details removing covers, shafts, gears, seals, and bearings during disassembly. The assembly section instructs lowering bearing temperatures and installing components in reverse order while applying sealant. Cleanliness is emphasized throughout to prevent contamination of hydraulic systems.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...f8ujkskdmdm
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then detail how to install the bearings at the proper temperatures and reassemble the components in reverse order.
3. Proper cleaning and replacement of seals is emphasized to prevent contamination of hydraulic systems.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...fusjekdkmd8ddjd
This document provides instructions for disassembling and assembling the auxiliary pump drive of an excavator. It begins with safety notices and a list of required tools. The disassembly steps include removing alignment pins, bolts, covers, seals, shafts, gears, and bearings from the pump drive body. The assembly steps list installing these components in reverse order, noting the importance of cleanliness and replacing seals. Torque and heating specifications are provided for installing bearings. The process is completed by reinstalling the auxiliary pump drive.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...zoat27912076
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Similar to Caterpillar cat 320 c ln excavator (prefix axk) service repair manual (axk00001 and up) (20)
New holland cx6080 tier 3 combine harvester service repair manualujfdjdjfkjksk
The document is a service manual that provides information on hydraulic, pneumatic, electrical, and electronic systems for CX5000 and CX6000 series equipment. It includes:
- Specifications and torque values for hydraulic fittings and connections
- Details on the primary hydraulic power system, including locations and functions of key components like pumps, valves, cylinders, and reservoirs
- Schematics and diagrams showing hydraulic system layout and component locations
The manual provides technical data, descriptions of functionality, and service information on critical fluid power and electrical systems to support maintenance and repair of the equipment.
New holland cx6080 cx6090 tier 4 combine harvester service repair manualujfdjdjfkjksk
The document is a service manual that provides information on hydraulic, pneumatic, electrical and electronic systems for CX5000 and CX6000 series equipment. It includes:
- Specifications and torque values for hydraulic fittings and connections.
- Details of the primary hydraulic system including three hydraulic pumps that power different circuits.
- A hydraulic schematic showing the layout of components in the hydraulic system.
- Images and descriptions locating hydraulic components on the front of the machine.
New holland cr9090 elevation combine harvesters service repair manualujfdjdjfkjksk
The primary hydraulic power system uses a variable displacement pump to power the work hydraulics and steering. Oil is filtered and distributed to valves controlling header height, reel functions, and other components. It is linked to the hydrostatic system, sharing a reservoir and using hydrostatic return oil as charge pressure. Key components include the pump, filters, relief valves, and control valves.
Caterpillar cat 903 d compact wheel loader (prefix mzy) service repair manual...ujfdjdjfkjksk
This service manual document provides instructions for removing and installing various components on a 903D Compact Wheel Loader, including:
1) The steering frame lock, which must be connected before working on the machine to prevent frame movement.
2) The hydraulic tank, which requires draining fluid and removing numerous hoses, fittings and bolts.
3) The joystick control and mounting, which is removed by disconnecting cables and harnesses after opening cab doors and covers.
4) The steering cylinder, which is removed after relieving pressure and disconnecting hoses by removing pins and clamps.
The document provides instructions for removing and installing various components of a Caterpillar 903C2 compact wheel loader engine, including:
- Removing the fuel manifold by removing bolts and disconnecting fuel injection lines.
- Removing fuel injection lines by disconnecting hoses and removing clamps and bolts.
- Removing the turbocharger by disconnecting hoses and removing mounting bolts.
- Removing the exhaust gas recirculation valve by removing mounting bolts and disconnecting hoses.
Caterpillar cat 903 c compact wheel loader (prefix w6t) service repair manual...ujfdjdjfkjksk
This document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It includes procedures for removing and installing fuel injection lines, nozzles, and the governor/camshaft assembly. Removal involves disconnecting lines, removing retaining bolts and brackets. Installation follows the removal process in reverse order. Precautions are given to prevent contamination of parts.
Caterpillar cat 903 c compact wheel loader (prefix mw4) service repair manual...ujfdjdjfkjksk
This document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader powered by a C2.4 engine. It includes procedures for removing and installing fuel injection lines and nozzles, as well as disassembling, assembling, removing and installing the governor and camshaft. Detailed illustrations accompany each step-by-step procedure to ensure correct part placement and tool usage. Proper cleanup and containment of fluids is emphasized throughout.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It outlines the disassembly and assembly procedures, including removing hoses and nuts to remove the pump. Detailed steps are provided to disassemble the pump components like the compensator, head, cylinders and pistons. Assembly instructions then describe cleaning and installing parts like seals, springs, bearings and swashplate in reverse order of disassembly. Safety notices are included to relieve pressure before removing lines or components.
This document provides instructions for removing and installing various components on a Caterpillar 527 Track Skidder, including the turbocharger, water temperature regulator, and radiator. The removal and installation procedures are described in detail in a step-by-step format and include illustrations. Safety and contamination prevention notices are also provided throughout the document.
This service repair manual provides instructions for removing and installing various fuel system components on a Caterpillar 527 Track Skidder with a 3304 engine, including:
- The fuel priming pump, which is removed by disconnecting hoses and removing bolts securing it to the engine block.
- The fuel filter base, which is removed by disconnecting fuel lines and removing bolts securing it to the fuel injection pump housing.
- The fuel transfer pump, which is removed by disconnecting inlet and outlet hoses and removing bolts securing it to the engine block.
The manual provides detailed step-by-step instructions and illustrations for each removal and installation procedure. Safety and contamination prevention procedures
This document provides instructions for connecting and disconnecting track components on a 517 Track Skidder. It describes a 13 step procedure for connecting the track that involves installing connection brackets, pulling the track over rollers using a loader, and engaging the sprocket segments. It also provides multi-step procedures for removing and installing track roller assemblies and sprocket segments on the final drive.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The removal process involves removing various lines and components to access the housing. Disassembly involves using various tools to remove parts like the camshaft, bearings, and lifters. Reassembly requires installing these parts in reverse order and ensuring proper clearance and positioning.
Caterpillar cat 428 d backhoe loader (prefix bll) service repair manual (bll0...ujfdjdjfkjksk
This document provides instructions for assembling the transmission of a 428D backhoe loader. It describes installing various transmission components like bearings, gears, shafts, and cases in multiple steps. It also explains how to install the fully assembled transmission in the machine and connect relevant components. The assembly procedure involves cleaning parts, applying oil, heating bearings, using various tools, and verifying clearances during installation.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...ujfdjdjfkjksk
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block that holds the pulley in position. The installation procedure specifies cleaning parts and installing in the reverse order, tightening the bolts to the specified torque.
Caterpillar cat 320 c l excavator (prefix mab) service repair manual (mab0000...ujfdjdjfkjksk
The document provides instructions for removing and disassembling the track, front idler, recoil spring, and hydraulic track adjuster on an excavator model 320C. Key steps include using tools to separate the track, remove the master pin, and separate the track links. Additional steps include using lifting devices to remove the front idler, recoil spring and hydraulic track adjuster assembly as a unit from the track roller frame, then separating these components. The recoil spring is further disassembled using a special tooling bench to adjust and remove the spring under controlled conditions due to its compressed state.
Caterpillar cat 257 d multi terrain loader (prefix fmr) service repair manual...ujfdjdjfkjksk
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including the engine oil relief valve, engine oil pump, water pump, water temperature regulator, and flywheel. The procedures describe removing parts, inspecting and cleaning components, and installing parts in the reverse order of removal while following safety precautions and using the appropriate tools. Torque specifications are provided where relevant.
Caterpillar cat 257 d multi terrain loader (prefix ezw) service repair manual...ujfdjdjfkjksk
The document provides instructions for removing and installing a piston pump on a 257D Multi Terrain Loader. It describes disconnecting hoses and harness assemblies, using various tools to support the pump during removal, and reversing the steps for installation. Detailed illustrations show each step in the disassembly and assembly process, including removing internal components like valves, seals, and bearings, and pressing them out or installing them back into place.
Caterpillar cat 247 b3 multi terrain loader (prefix tsl) service repair manua...ujfdjdjfkjksk
This document provides instructions for disassembling and assembling the piston pump of a 247B3 Multi Terrain Loader. It lists 69 required steps for disassembly, including removing fittings, springs, seals, pins, and other components. Similarly, it lists 17 steps for reassembling components like liners, seals, actuators, bearings, and retaining rings. Tools required include rulers, pliers, drivers, pullers, and grease. Cautions are provided about spring forces and ensuring dowel pin alignment during assembly.
Caterpillar cat 247 b3 multi terrain loader (prefix kb3) service repair manua...ujfdjdjfkjksk
This document provides disassembly and assembly instructions for the piston pump of a 247B3 Multi Terrain Loader powered by a C2.2 engine. The disassembly procedure involves 69 steps to remove components like fittings, springs, seals, bearings, and shafts. The assembly procedure reverses the disassembly steps and provides additional guidance like applying grease or thread lock compounds during reassembly. Tools required include various pliers, pullers, rulers, drivers and grease.
Caterpillar cat 247 b3 multi terrain loader (prefix esl) service repair manua...ujfdjdjfkjksk
This document provides disassembly instructions for a piston motor (hydrostatic) on a Caterpillar 247B3 Multi Terrain Loader. It lists 31 steps to fully disassemble the piston motor, including removing covers, gaskets, seals, discs, shafts, cases, bushings, pins, springs, pistons, rotors and bearings. Tools required include drivers, punches, retaining ring pliers, bolts, washers, bearings pullers and blocking fixtures. Personal protective equipment is recommended when removing or blocking parts under spring pressure.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01146335
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00607826
Note: Illustration 1 does not show that the front housing is removed from the cylinder
block.
1. Remove bolt (1) from the cover (2) .
2. Remove cover (2) for the engine oil pump from the front housing. Check gasket (3) (not
shown) for damage or wear. Replace the gasket, if the gasket is worn or damaged.
Illustration 2 g00607770
2/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5)
(slip fit).
Illustration 3 g00607857
4. Position the front housing on a work bench in order to remove the oil pump gear from the
rear of the housing.
5. Use Tool (A) to remove oil pump gear (6) from the front housing.
Illustration 4 g00607885
6. Position the front housing on a work bench in order to remove the drive gear from the front
of the housing.
7. Remove drive gear (7) from the front housing.
3/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 5 g00607947
8. Use Tool (B) to remove front oil seal (8) (not shown) from the front housing.
Illustration 6 g00607955
Note: Illustration 6 does not show that the front seal (8) is removed.
9. Remove set screw (9) from the front housing.
Illustration 7 g00607962
4/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 8 g00607966
Note: Illustration 7 does not show that the front seal (8) is removed.
10. Remove spindle (10) and idler gear (11) as an assembly. Push on the gear with a hardwood
bar (12) through the mounting hole for the front seal. Rotate the gear while the gear is
pushed.
Note: Use care not to damage the pump idler gear and the crankshaft gear.
Note: Replace the drive gear and the driven gear as an assembly.
Note: Do not attempt to reuse the oil pump gear and drive gear assembly. Replace the oil pump
gear and the drive gear assembly with new parts.
Note: Check all of the gears for worn teeth or damaged teeth. Replace the gears, if necessary.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:10:22 UTC+0800 2019
5/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01146555
Engine Oil Pump - Install
SMCS - 1304-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g00646132
1. Use Tool (A) to install the front oil seal (8) (not shown).
Illustration 2 g00607962
2. Lower the temperature of the spindle (10). Install spindle (10) and idler gear (11) as an
assembly in the front housing.
Note: The temperature of the spindle is lowered in order to ease the installation of the
spindle in the front housing.
Illustration 3 g00607955
3. Install set screw (9) in the front housing.
2/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 4 g00607885
4. Lower the temperature of the drive gear assembly. Install drive gear (7) in the front housing.
Note: The temperature of the drive gear assembly is lowered in order to ease the installation
of the drive gear assembly in the front housing.
Illustration 5 g00608012
Always wear protective gloves when handling parts that have been
heated.
3/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. 5. Heat the oil pump gear up to 180 to 220 °C (356 to 428 °F). Support end (X) of the shaft (7)
(drive gear). Install oil pump gear (6) onto the shaft. The end of the gear (Z) should be flush
with the end of the shaft (Y) .
Illustration 6 g00607770
6. Install driven gear (4) into the front housing (slip fit).
Illustration 7 g00607826
7. Place gasket (3) and cover (2) in position on the front housing.
Note: Ensure that the old gasket material is removed from the mating surfaces.
8. Install the washer and bolt (1) that secures the cover to the front housing. Tighten bolt (1) to
a torque of 34 ± 5 N·m (25 ± 4 lb ft).
Refer to the Specifications Module, "Engine Oil Pump" for more information on the engine oil
pump.
End By: Install the front housing. Refer to Disassembly and Assembly, " Housing (Front) -
Install".
4/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:11:18 UTC+0800 2019
5/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01149671
Water Pump - Remove
SMCS - 1361-011
Removal Procedure
Start By:
A. Remove V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
filler cap is cool enough to touch with the bare hand.
Remove the filler cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid contact with skin and
eyes to prevent personal injury.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Illustration 1 g00609950
2. Remove four bolts (1) that secure the water pump to the engine.
3. Remove water pump pulley (2) and water pump (3) as an unit from the engine.
4. Remove O-ring (4) (not shown) from water pump (3). Discard the old O-ring.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:12:13 UTC+0800 2019
2/2(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01566087
Water Pump - Disassemble
SMCS - 1361-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Group 1
Start By:
A. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
Note: If the water pump is heated up to 80 °C (176 °F), the components can be easily removed.
1/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 1 g00610108
1. Remove four bolts (1) and the washers that secure the water pump pulley to the water pump.
2. Remove water pump pulley (2) from the water pump.
Note: Check the groove for the V-belt of the water pump pulley for wear and damage. Replace the
water pump pulley, if necessary.
Note: Use Tool (C) during disassembly procedures of the water pump, which require the use of a
press or a hammer.
Illustration 2 g00610120
3. Use Tool (A) to remove flange (3) from the water pump.
2/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 3 g00610127
4. Use Tool (B) to remove retaining ring (4) from the water pump.
Illustration 4 g00610140
5. Use a press and Tool (C) to remove shaft assembly (5) from water pump assembly (6) .
3/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 5 g00813948
6. Remove impeller (8) from the shaft assembly (5) .
Note: Check the impeller for wear, corrosion, and metal to metal contact. Replace the impeller, if
necessary.
7. Remove the following items from shaft (9) :
◦ Bearing (10)
◦ Spacer (11)
◦ Bearing (12)
◦ Washer (13)
8. Once all of the components have been removed, then check shaft (9) for distortion. Replace the shaft,
if necessary.
9. Check seal (14) for wear and damage. Use Tool (C) in order to remove the seal from the water pump
housing, if necessary.
Note: Replace the seal if any signs of leakage occurs during the operation of the water pump.
10. Replace O-ring (7) with a new O-ring.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:13:09 UTC+0800 2019
4/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01566223
Water Pump - Assemble
SMCS - 1361-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 1P-1861 Retaining Ring Pliers 1
Note: Refer to Specifications, "Water Pump" for specifications that are required during assembly.
1/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 1 g00813948
1. Install seal (14), if the seal was removed during the disassembly procedures.
2. The following components are installed on shaft (9) :
◦ Washer (13)
◦ Bearing (12)
◦ Spacer (11)
◦ Bearing (10)
Note: Check two bearings (10) and (12) for correct rotation.
2/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 2 g00610140
3. Use a press and Tool (A) to install shaft assembly (5) into the water pump housing.
4. Use a press and Tool (A) to install impeller (8) onto shaft assembly (5) .
Illustration 3 g00610127
5. Use Tool (B) to install retaining ring (4) into the water pump housing.
6. Use a press and Tool (A) to install flange (3) onto shaft assembly (5) .
Illustration 4 g00610108
3/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. 7. Install water pump pulley (2) onto the flange.
8. Install four bolts (1) in order to secure water pump pulley (2) to the flange.
End By: Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:14:05 UTC+0800 2019
4/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01149732
Water Pump - Install
SMCS - 1361-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00609950
1. Replace O-ring (4) (not shown) with a new part. Apply glycerine to the O-ring before the
installation of the water pump (3) and water pump pulley (2) .
1/2(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. 2. Install the water pump (3) and water pump pulley (2) as a unit onto the engine.
Note: When the water pump is installed, ensure that the grease fitting is up. Also, ensure
that the weep hole is down.
3. Install bolts (1) in order to secure water pump (3) to the cylinder block.
4. Fill the cooling system to the correct level. Refer to the appropriate Operation and
Maintenance Manual for the correct fluid and the correct filling procedure.
End By: Install V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:15:00 UTC+0800 2019
2/2(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01148678
Water Temperature Regulator - Remove and Install
SMCS - 1355-010
Removal Procedure
At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
filler cap is cool enough to touch with the bare hand.
Remove the filler cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid contact with skin and
eyes to prevent personal injury.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant level below the water temperature regulator.
Illustration 1 g00609693
2. Loosen hose clamp (1) and disconnect hose (2) from cover (4) of the water temperature
regulator.
3. Remove two bolts (3) and the washers from cover (4) of the water temperature regulator.
4. Separate cover (4) from elbow (5) .
5. Remove bolts (6). Separate elbow (5) from the water outlet manifold.
6. Remove water temperature regulator (8) (not shown) from cover (4) .
7. Remove gasket (7) (not shown) and gasket (9) (not shown) from the mounting surfaces of
cover (4) and elbow (5) .
8. Use the following procedure in order to test the water temperature regulator:
a. Put the water temperature regulator in a tub of water. Heat the water in order to test
the water temperature regulator for thermostatic action.
Note: Stir the water in the tub in order to maintain even temperature during the test.
2/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. b. When the valve of the water temperature regulator lifts more than 10 mm (0.4 inch),
measure the water temperature.
Note: The opening temperature for the water temperature regulator is 71° ± 2°C (160°
± 3.6°F).
c. If the valve fails to operate properly, replace the water temperature regulator.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all of the mounting surfaces for the gaskets and remove all gasket material.
NOTICE
If the water temperature regulator is installed incorrectly, it will cause
the engine to overheat.
Illustration 2 g00609693
2. Install water temperature regulator (8) (not shown) into elbow (5) .
Note: When the water temperature regulator is installed, ensure that the hole for the air vent
is up.
3. Install gasket (7) (not shown) and gasket (9) (not shown).
3/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...