This document provides instructions for removing and installing a flywheel housing on a 320C excavator engine. It describes:
1. Removing the electric starting motor and flywheel/ring gear as preliminary steps.
2. Using various tools like a link bracket and driver group to remove the 12 bolts securing the adapter to the flywheel housing and then remove the housing.
3. Reversing the process to install a new or repaired flywheel housing, ensuring all bolts are properly tightened.
Caterpillar cat 320 track type excavator (prefix 9 kk) service repair manual ...ufujjdjkskemme
- The document provides instructions for removing and installing a flywheel, flywheel housing, crankshaft pulley, and crankshaft rear seal on an excavator engine.
- To remove the flywheel, the bolts securing it must be removed, then a lifting device is used to pull it off. The flywheel housing is removed by lifting it off with bolts and contains an oil seal that may need replacing.
- The crankshaft rear seal is removed using a slide hammer and distorter tools, and installed using a installer tool and retaining compound. The crankshaft pulley is removed using a puller tool and a socket.
Caterpillar cat 320 track type excavator (prefix 1 xm) service repair manual ...ufjdfjjkskemme
This document provides instructions for removing and installing a crankshaft pulley on an excavator engine. The removal procedure involves using a combination puller tool to pull the pulley off the crankshaft. For installation, the pulley is pressed back onto the crankshaft using an installer tool. Safety precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 323 d l excavator (prefix nzf) service repair manual (nzf0000...fjjsekmsmmes
This service manual provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.6 engine. The procedure involves using special tools to compress the valve springs, remove the keepers, and access the valves. The springs must be removed and installed in pairs per cylinder to ensure proper valve timing. Technicians are advised to clean all parts thoroughly and position the pistons carefully before compressing the springs.
Caterpillar cat 323 d l excavator (prefix wne) service repair manual (wne0000...fjskksmem
The document provides instructions for installing the crankshaft in a Caterpillar C6.4 engine:
1. Thrust washers and main bearings are installed in the cylinder block and bearing caps.
2. The crankshaft is positioned onto the main bearings using a lifting device.
3. Main bearing caps with bearings are installed and torqued to specifications.
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
Caterpillar cat 312 b excavator (prefix 2ns) service repair manual (2ns00001 ...fjsekksmemm
The document provides instructions for removing and installing a flywheel on a Caterpillar 312B excavator engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel out of the housing using a strap and lifting device.
3) Removing the ring gear by heating it and tapping it off.
4) Reversing the process to install a new flywheel, pressing the heated ring gear onto the flywheel if needed.
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1. The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2. The installation procedure specifies using the same special tool to install the bearings at precise depths in the cylinder block and checking the bore size after installation.
3. Reinstalling components like the flywheel housing, balancer shaft, and oil pan completes the process.
Caterpillar cat 320 e lrr excavator (prefix pnl) service repair manual (pnl00...fujdfjjkskekme
1) The document provides instructions for removing and installing a front cover on a Caterpillar C6.6 engine.
2) It describes using various tools to remove bolts and separate the front cover from the front housing. The front seal and gasket must also be removed.
3) Cleaning surfaces and installing a new gasket and seal are covered. Alignment tools are used to correctly position the new front cover assembly before tightening bolts.
Caterpillar cat 320 track type excavator (prefix 9 kk) service repair manual ...ufujjdjkskemme
- The document provides instructions for removing and installing a flywheel, flywheel housing, crankshaft pulley, and crankshaft rear seal on an excavator engine.
- To remove the flywheel, the bolts securing it must be removed, then a lifting device is used to pull it off. The flywheel housing is removed by lifting it off with bolts and contains an oil seal that may need replacing.
- The crankshaft rear seal is removed using a slide hammer and distorter tools, and installed using a installer tool and retaining compound. The crankshaft pulley is removed using a puller tool and a socket.
Caterpillar cat 320 track type excavator (prefix 1 xm) service repair manual ...ufjdfjjkskemme
This document provides instructions for removing and installing a crankshaft pulley on an excavator engine. The removal procedure involves using a combination puller tool to pull the pulley off the crankshaft. For installation, the pulley is pressed back onto the crankshaft using an installer tool. Safety precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 323 d l excavator (prefix nzf) service repair manual (nzf0000...fjjsekmsmmes
This service manual provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.6 engine. The procedure involves using special tools to compress the valve springs, remove the keepers, and access the valves. The springs must be removed and installed in pairs per cylinder to ensure proper valve timing. Technicians are advised to clean all parts thoroughly and position the pistons carefully before compressing the springs.
Caterpillar cat 323 d l excavator (prefix wne) service repair manual (wne0000...fjskksmem
The document provides instructions for installing the crankshaft in a Caterpillar C6.4 engine:
1. Thrust washers and main bearings are installed in the cylinder block and bearing caps.
2. The crankshaft is positioned onto the main bearings using a lifting device.
3. Main bearing caps with bearings are installed and torqued to specifications.
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
Caterpillar cat 312 b excavator (prefix 2ns) service repair manual (2ns00001 ...fjsekksmemm
The document provides instructions for removing and installing a flywheel on a Caterpillar 312B excavator engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel out of the housing using a strap and lifting device.
3) Removing the ring gear by heating it and tapping it off.
4) Reversing the process to install a new flywheel, pressing the heated ring gear onto the flywheel if needed.
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1. The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2. The installation procedure specifies using the same special tool to install the bearings at precise depths in the cylinder block and checking the bore size after installation.
3. Reinstalling components like the flywheel housing, balancer shaft, and oil pan completes the process.
Caterpillar cat 320 e lrr excavator (prefix pnl) service repair manual (pnl00...fujdfjjkskekme
1) The document provides instructions for removing and installing a front cover on a Caterpillar C6.6 engine.
2) It describes using various tools to remove bolts and separate the front cover from the front housing. The front seal and gasket must also be removed.
3) Cleaning surfaces and installing a new gasket and seal are covered. Alignment tools are used to correctly position the new front cover assembly before tightening bolts.
Caterpillar cat 330 b l excavator (prefix 1js) service repair manual (1js0000...fjskefkemms
This document provides instructions for removing and installing various engine components on a 330B L EXCAVATOR, including:
- Exhaust manifold removal and installation requiring removal of the turbocharger and fuel lines.
- Inlet and exhaust valve removal and installation using specialized tools to compress springs.
- Removal and installation of valve guides, seats, and inserts using driver tools to precisely install components.
- Removal of the engine oil filter base requiring a strap wrench to remove the oil filter.
Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml000...fjskefkemms
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr0000...fjskefkemms
The document provides instructions for servicing components of a 330B L excavator including:
1. Installing a compression brake on the engine and connecting wires.
2. Removing and assembling the rocker shaft and pushrods, including disassembling the rocker shaft into individual components.
3. Removing the cylinder head from the engine which involves removing manifold, pushrods, and bolts holding the head in place. Proper lifting equipment is needed due to the head's weight.
This document provides installation and removal procedures for components of a C27 industrial locomotive engine:
1) It details the removal and installation of the front gear group, including bushings, shafts, and plates.
2) The removal of the front housing requires disconnecting various components and brackets before lifting the housing off.
3) Reinstallation of the front housing involves lowering it onto dowel pins and torquing bolts in a specific sequence.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
Caterpillar cat 320 c excavator (prefix dbg) service repair manual (dbg00001 ...ufjjsjekkeemme
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 345 b series ii excavator (prefix dcw) service repair manual ...fujsekfkksemm
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176 engine. The removal procedure involves removing components like the valve mechanism cover, rocker shaft, and pushrods. Sensors and tubes must be disconnected from the cylinder head before removing bolts and lifting the head off. For installation, the mating surfaces are cleaned and the correct gasket is installed before lowering the head onto the cylinder block and installing bolts.
Caterpillar cat 345 b series ii excavator (prefix ald) service repair manual ...fujsekfkksemm
This document provides instructions for installing a cylinder head on a 3176C engine. It involves cleaning surfaces, installing gaskets and seals, lifting the cylinder head into place using guide bolts, and tightening head bolts in a specific sequence to the correct torque specifications. Sensors and wiring are then reconnected, coolant is added to the system, and remaining components like the rocker shaft and pushrods are reinstalled to complete the job.
Caterpillar cat 345 b series ii excavator (prefix ccc) service repair manual ...fujsekfkksemm
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds. The cylinder head bolts are then removed and the head lifted off using a suitable lifting device. For installation, the mating surfaces are cleaned and new gaskets installed before positioning the cylinder head on the block and installing the bolts.
Caterpillar cat 345 c excavator (prefix dhp) service repair manual (dhp00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and piston assemblies. It notes to mark parts for reinstallation and clean components to prevent contamination. Reassembly follows the reverse order of disassembly.
Caterpillar cat 345 c excavator (prefix spc) service repair manual (spc00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C L EXCAVATOR. It lists 31 steps to disassemble the various components of the travel motor using different tools. These components include the head, plates, seals, pins, brake piston, disks, rotating group, shaft assembly, barrels, seals, and more. It notes to mark parts for reinstallation and clean components thoroughly. The assembly procedure is listed but not described in detail.
Caterpillar cat 345 c excavator (prefix wde) service repair manual (wde00001 ...fujsekfkksemm
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 30 parts from the final drive assembly using various tools. The assembly procedure is the reverse of the disassembly process and includes applying thread lock compound and gasket sealant to specific joints.
Caterpillar cat 345 c hydraulic excavator (prefix tdg) service repair manual ...fujsekfkksemm
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 13 steps for assembly, reinstalling these components in reverse order and noting to clean all parts, apply lubricant, and replace all seals and gaskets. Precise measurements and tooling are required to properly assemble the travel motor.
Caterpillar cat 345 c l excavator (prefix scn) service repair manual (scn0000...fujsekfkksemm
This document provides step-by-step instructions for disassembling and assembling the final drive of a 345C L excavator. It details removing over 30 individual components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. Reassembly follows the reverse order, with notes to reinstall parts in their original positions and orientations. Required tools include transmission stands, eyebolts, retaining ring pliers, and seal installers.
Caterpillar cat 345 c l excavator (prefix s5m) service repair manual (s5m0000...fujsekfkksemm
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C L Excavator. The disassembly process involves removing over 20 individual parts from the final drive housing including gears, shafts, bearings, seals and other components. Proper identification of part locations and orientations is emphasized for reassembly. Required tools include lifting devices, retaining ring pliers, eyebolts and other specialized tools.
Caterpillar cat 345 c l excavator (prefix spc) service repair manual (spc0000...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C L EXCAVATOR. It lists 31 steps to disassemble the various components of the travel motor including removing the head, brake piston, disks, rotating group, piston assemblies, seals and more. Detailed illustrations are provided to identify each part. When assembling, the instructions note to clean all parts and reinstall components in their original locations and orientations. Precautions are outlined to contain fluids, avoid damage, and prevent contamination.
Caterpillar cat 345 c l excavator (prefix wde) service repair manual (wde0000...fujsekfkksemm
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 30 parts from the final drive assembly using various tools. The assembly procedure is the reverse of the disassembly steps and includes applying thread lock compound and gasket sealant to specific joints.
Caterpillar cat 345 b l excavator (prefix 9cw) service repair manual (9cw0000...fujsekfkksemm
This document provides instructions for removing and installing the rocker shaft, pushrods, and cylinder head on a Caterpillar 345B L excavator engine. The removal procedure involves removing covers, shafts, rods, sensors and manifolds. The cylinder head is then lifted off. The installation procedure specifies cleaning components, installing gaskets and seals, and torquing bolts to specifications when reassembling the cylinder head and related parts.
Caterpillar cat 345 b l excavator (prefix 8rw) service repair manual (8rw0000...fujsekfkksemm
This document provides instructions for installing a cylinder head on a 345B L EXCAVATOR engine. It describes cleaning and inspecting the cylinder head and block mating surfaces. The correct cylinder head gasket must be installed, along with new O-rings. The cylinder head is placed on guide bolts and bolts are tightened in a specific sequence to the correct torques. Sensors and lines are then reconnected to the cylinder head before installing the water outlet manifold.
Caterpillar cat 345 b excavator (prefix ayr) service repair manual (ayr00001 ...fujsekfkksemm
This document provides instructions for disassembling and assembling the final drive components of an excavator model 345B. It describes removing 27 components including the travel motor, final drive, carrier assemblies, ring gear, and sprocket housing. Detailed illustrations and notes are provided to aid in correctly identifying parts and maintaining proper orientation during reassembly. Required tools include various link brackets, retaining ring pliers, seal installer, anti-seize compound, grease, thread lock, gasket sealant and a transmission stand.
Caterpillar cat 345 b excavator (prefix amn) service repair manual (amn00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pistons, bearings and housing. It also lists tools required for the job and safety notices about keeping parts clean and containing fluids.
Caterpillar cat 330 b l excavator (prefix 1js) service repair manual (1js0000...fjskefkemms
This document provides instructions for removing and installing various engine components on a 330B L EXCAVATOR, including:
- Exhaust manifold removal and installation requiring removal of the turbocharger and fuel lines.
- Inlet and exhaust valve removal and installation using specialized tools to compress springs.
- Removal and installation of valve guides, seats, and inserts using driver tools to precisely install components.
- Removal of the engine oil filter base requiring a strap wrench to remove the oil filter.
Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml000...fjskefkemms
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr0000...fjskefkemms
The document provides instructions for servicing components of a 330B L excavator including:
1. Installing a compression brake on the engine and connecting wires.
2. Removing and assembling the rocker shaft and pushrods, including disassembling the rocker shaft into individual components.
3. Removing the cylinder head from the engine which involves removing manifold, pushrods, and bolts holding the head in place. Proper lifting equipment is needed due to the head's weight.
This document provides installation and removal procedures for components of a C27 industrial locomotive engine:
1) It details the removal and installation of the front gear group, including bushings, shafts, and plates.
2) The removal of the front housing requires disconnecting various components and brackets before lifting the housing off.
3) Reinstallation of the front housing involves lowering it onto dowel pins and torquing bolts in a specific sequence.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
Caterpillar cat 320 c excavator (prefix dbg) service repair manual (dbg00001 ...ufjjsjekkeemme
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 345 b series ii excavator (prefix dcw) service repair manual ...fujsekfkksemm
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176 engine. The removal procedure involves removing components like the valve mechanism cover, rocker shaft, and pushrods. Sensors and tubes must be disconnected from the cylinder head before removing bolts and lifting the head off. For installation, the mating surfaces are cleaned and the correct gasket is installed before lowering the head onto the cylinder block and installing bolts.
Caterpillar cat 345 b series ii excavator (prefix ald) service repair manual ...fujsekfkksemm
This document provides instructions for installing a cylinder head on a 3176C engine. It involves cleaning surfaces, installing gaskets and seals, lifting the cylinder head into place using guide bolts, and tightening head bolts in a specific sequence to the correct torque specifications. Sensors and wiring are then reconnected, coolant is added to the system, and remaining components like the rocker shaft and pushrods are reinstalled to complete the job.
Caterpillar cat 345 b series ii excavator (prefix ccc) service repair manual ...fujsekfkksemm
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds. The cylinder head bolts are then removed and the head lifted off using a suitable lifting device. For installation, the mating surfaces are cleaned and new gaskets installed before positioning the cylinder head on the block and installing the bolts.
Caterpillar cat 345 c excavator (prefix dhp) service repair manual (dhp00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and piston assemblies. It notes to mark parts for reinstallation and clean components to prevent contamination. Reassembly follows the reverse order of disassembly.
Caterpillar cat 345 c excavator (prefix spc) service repair manual (spc00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C L EXCAVATOR. It lists 31 steps to disassemble the various components of the travel motor using different tools. These components include the head, plates, seals, pins, brake piston, disks, rotating group, shaft assembly, barrels, seals, and more. It notes to mark parts for reinstallation and clean components thoroughly. The assembly procedure is listed but not described in detail.
Caterpillar cat 345 c excavator (prefix wde) service repair manual (wde00001 ...fujsekfkksemm
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 30 parts from the final drive assembly using various tools. The assembly procedure is the reverse of the disassembly process and includes applying thread lock compound and gasket sealant to specific joints.
Caterpillar cat 345 c hydraulic excavator (prefix tdg) service repair manual ...fujsekfkksemm
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 13 steps for assembly, reinstalling these components in reverse order and noting to clean all parts, apply lubricant, and replace all seals and gaskets. Precise measurements and tooling are required to properly assemble the travel motor.
Caterpillar cat 345 c l excavator (prefix scn) service repair manual (scn0000...fujsekfkksemm
This document provides step-by-step instructions for disassembling and assembling the final drive of a 345C L excavator. It details removing over 30 individual components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. Reassembly follows the reverse order, with notes to reinstall parts in their original positions and orientations. Required tools include transmission stands, eyebolts, retaining ring pliers, and seal installers.
Caterpillar cat 345 c l excavator (prefix s5m) service repair manual (s5m0000...fujsekfkksemm
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C L Excavator. The disassembly process involves removing over 20 individual parts from the final drive housing including gears, shafts, bearings, seals and other components. Proper identification of part locations and orientations is emphasized for reassembly. Required tools include lifting devices, retaining ring pliers, eyebolts and other specialized tools.
Caterpillar cat 345 c l excavator (prefix spc) service repair manual (spc0000...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C L EXCAVATOR. It lists 31 steps to disassemble the various components of the travel motor including removing the head, brake piston, disks, rotating group, piston assemblies, seals and more. Detailed illustrations are provided to identify each part. When assembling, the instructions note to clean all parts and reinstall components in their original locations and orientations. Precautions are outlined to contain fluids, avoid damage, and prevent contamination.
Caterpillar cat 345 c l excavator (prefix wde) service repair manual (wde0000...fujsekfkksemm
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 30 parts from the final drive assembly using various tools. The assembly procedure is the reverse of the disassembly steps and includes applying thread lock compound and gasket sealant to specific joints.
Caterpillar cat 345 b l excavator (prefix 9cw) service repair manual (9cw0000...fujsekfkksemm
This document provides instructions for removing and installing the rocker shaft, pushrods, and cylinder head on a Caterpillar 345B L excavator engine. The removal procedure involves removing covers, shafts, rods, sensors and manifolds. The cylinder head is then lifted off. The installation procedure specifies cleaning components, installing gaskets and seals, and torquing bolts to specifications when reassembling the cylinder head and related parts.
Caterpillar cat 345 b l excavator (prefix 8rw) service repair manual (8rw0000...fujsekfkksemm
This document provides instructions for installing a cylinder head on a 345B L EXCAVATOR engine. It describes cleaning and inspecting the cylinder head and block mating surfaces. The correct cylinder head gasket must be installed, along with new O-rings. The cylinder head is placed on guide bolts and bolts are tightened in a specific sequence to the correct torques. Sensors and lines are then reconnected to the cylinder head before installing the water outlet manifold.
Caterpillar cat 345 b excavator (prefix ayr) service repair manual (ayr00001 ...fujsekfkksemm
This document provides instructions for disassembling and assembling the final drive components of an excavator model 345B. It describes removing 27 components including the travel motor, final drive, carrier assemblies, ring gear, and sprocket housing. Detailed illustrations and notes are provided to aid in correctly identifying parts and maintaining proper orientation during reassembly. Required tools include various link brackets, retaining ring pliers, seal installer, anti-seize compound, grease, thread lock, gasket sealant and a transmission stand.
Caterpillar cat 345 b excavator (prefix amn) service repair manual (amn00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pistons, bearings and housing. It also lists tools required for the job and safety notices about keeping parts clean and containing fluids.
Caterpillar cat 345 b excavator (prefix amj) service repair manual (amj00001 ...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1. It describes preparing the travel motor components and inserting keys, seals, pistons, plates and spacers into the motor body.
2. It explains assembling the barrel, installing the shaft and bearings, and inserting friction disks and separator plates.
3. It outlines attaching the head, installing valves, plugs and seals to complete the assembly. Precise measurements and torque specifications are listed to ensure correct assembly.
Caterpillar cat 345 b excavator (prefix amd) service repair manual (amd00001 ...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1) It describes preparing the travel motor body by installing seals, pistons, and spacers.
2) It explains assembling the barrel, installing the shaft and bearings, and inserting friction disks and plates.
3) It outlines attaching the head, installing valves and plugs, and filling the travel motor with oil before operation.
Caterpillar cat 345 b excavator (prefix 8kw) service repair manual (8kw00001 ...fujsekfkksemm
This document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Excavator engine. The removal process involves removing covers, shafts, rods, sensors, tubes, and manifolds before lifting the cylinder head off. The installation process specifies cleaning, inspecting, and lubricating components before lowering the cylinder head back onto the engine and reinstalling related parts in reverse order of removal. Tools and torque specifications are listed for select steps.
Caterpillar cat 345 b excavator (prefix 6mw) service repair manual (6mw00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345B Excavator. It lists 32 steps for disassembly, including removing covers, springs, seals, gears, and housing components. It then lists 15 steps for assembly, reversing the disassembly process and including inspecting parts and ensuring cleanliness to prevent contamination. The overall document provides detailed technical instructions for servicing the excavator's travel motor.
Caterpillar cat 340 f excavator (prefix sgh) service repair manual (sgh00001 ...fujsekfkksemm
The document provides disassembly instructions for a swing drive on a 340F excavator model. It begins by having the technician remove the swing drive and mark parts for reassembly. Several internal components of the swing drive are then removed, including planetary gears, shafts, rings, and housings. Precision tools are required and technicians should be careful due to the weights of parts removed. Cleanliness is emphasized to prevent contamination of hydraulic systems during repair.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR SBN
Configuration: 320C & 320C L Excavators SBN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567208
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B Forcing screws M16 X 2 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00605492
1. Remove twelve bolts (1) and washers from the adapter (2) .
2. Remove the adapter (2) from the flywheel housing.
Illustration 2 g00605497
3. Remove four socket head bolts (3) from the inner ring (4) .
4. Remove the inner ring (4) from the flywheel.
2/4(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 3 g00605501
5. Remove six bolts (5) that secure flywheel (6) to the crankshaft. Check all bolts for stripped
threads. Replace the bolts, if necessary.
Illustration 4 g00605504
6. Install Tool (A), a strap, and a suitable lifting device onto the flywheel (6).
7. Use Tool (B) in order to remove the flywheel and ring gear out of the housing. The weight
of the flywheel is 50 kg (110 lb).
8. Perform the following procedure in order to remove the flywheel ring gear.
Illustration 5 g00613038
a. Place the flywheel and ring gear assembly on a suitable support.
Note: Check the flywheel ring gear for the following conditions:cracks, damaged
dowel holes, worn ring gear and damaged ring gear.
Note: Identify the orientation of the old ring gear on the flywheel for proper
positioning, when the new ring gear is installed.
3/4(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Always wear protective gloves when handling parts that have been
heated.
b. Heat ring gear (7) uniformly.
c. Remove the ring gear (7) by tapping the ring gear all the way around the flywheel
(6) .
d. Reposition the flywheel in order to remove the ring gear.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 26 17:33:19 UTC+0800 2019
4/4(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR SBN
Configuration: 320C & 320C L Excavators SBN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567260
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Heat the ring gear to 150 �C (302 �F) in an oven.
1/3(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. b. Press the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g00605504
2. Install Tool (A), a strap, and a suitable lifting device onto flywheel (6) .
3. Install flywheel (6). The weight of the flywheel is 50 kg (110 lb).
Illustration 2 g00605501
4. Install six bolts (5) in order to secure flywheel (6) onto the crankshaft. Tighten the bolts to a
torque of 83 � 5 N�m (61 � 4 lb ft).
5. Remove Tool (A) from the flywheel.
2/3(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 3 g00605497
6. Place the inner ring (4) in position on the flywheel.
7. Install four socket head bolts (3) in order to secure the inner ring (4) to the flywheel.
Illustration 4 g00605492
8. Place the adapter (2) in position on the flywheel housing.
9. Install twelve bolts and washers (1) in order to secure the adapter (2) on the flywheel
housing.
10. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 26 17:34:15 UTC+0800 2019
3/3(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR SBN
Configuration: 320C & 320C L Excavators SBN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 26 17:35:10 UTC+0800 2019
3/3(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR SBN
Configuration: 320C & 320C L Excavators SBN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 26 17:36:06 UTC+0800 2019
3/3(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR SBN
Configuration: 320C & 320C L Excavators SBN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i05421135
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the electric starting motor.
B. Remove the flywheel and ring gear.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 1 g00605593
1. Install Tooling (A) , a strap, and a suitable lifting device onto flywheel housing (2) .
2. Remove bolts (1) and the washers that secure flywheel housing (2) to the cylinder block.
Note: Identify the four shorter bolts for later installation into the flywheel housing.
3. Remove flywheel housing (2) . The weight of the flywheel is approximately.29 kg (65 lb).
4. Check oil seal (3) for serviceability. If necessary, replace the oil seal and crankshaft wear
sleeve.
Illustration 2 g00605601
5. Use Tooling (B) in order to remove the oil seal (3) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
2/3(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. B 9U-6170 Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00605593
1. Clean old gasket material (4) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
2. Place flywheel housing (2) in position on the cylinder block.
3. Install the washers and bolts (1) in order to secure flywheel housing (2) to the cylinder
block.
4. Use Tooling (B) in order to install the oil seal (3) , and the crankshaft wear sleeve (not
shown).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 26 17:37:02 UTC+0800 2019
3/3(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR SBN
Configuration: 320C & 320C L Excavators SBN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01578488
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket (1)
1
( 1 )
Tool (B) is a 46 mm socket.
Start By:
A. Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 1 g00604778
1. Use Tool (B) to remove nut (1) and washer (2) from the threaded end of the crankshaft.
Illustration 2 g00604784
2. Use Tool (A) to remove crankshaft pulley (3) from the engine.
2/4(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 3 g00604792
3. If it is necessary to remove the wear sleeve (4) from the crankshaft pulley (3), use a hammer
and a chisel. Hold the chisel at right angles to the surface of the wear sleeve. Tap the wear
sleeve in three places. You can remove the wear sleeve once the tension is released.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00604778
3/4(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. 1. Put crankshaft pulley (3) in position on the engine.
2. Install washer (2) and nut (1). Use Tool (B) to tighten nut (1) to a torque of 490 � 10 N�m
(361 � 7 lb ft).
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 26 17:37:58 UTC+0800 2019
4/4(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR SBN
Configuration: 320C & 320C L Excavators SBN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01131366
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft front seal (1) .
2. Use Tool (A) and remove crankshaft front seal (1). Remove the seal evenly by alternating
the position of Tool (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 26 17:38:53 UTC+0800 2019
2/2(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR SBN
Configuration: 320C & 320C L Excavators SBN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i02080454
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 1 g00612743
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Install new crankshaft front seal (1) in the front housing with Tool (A) .
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By: Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 26 17:39:49 UTC+0800 2019
2/2(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR SBN
Configuration: 320C & 320C L Excavators SBN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615339
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Before removal, ensure that the marks on the timing gears are in alignment. Align the
fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
Illustration 1 g00611568
1. Remove idler gear bolt (1) and the washer from the idler gear shaft .
2. Remove thrust plate (2) from the idler gear shaft.
2/5(W)w
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...