This document provides the disassembly and assembly procedures for the travel motor on a 318F L excavator. It outlines 31 steps to disassemble the travel motor by removing components like springs, spools, caps, guides, pistons and housings. It then outlines 29 steps for reassembling the travel motor by reversing the disassembly process and reinstalling all components in the proper orientation. Precautions are provided to watch for spring loaded parts and ensure proper tightening of components.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a multi-step process for removing components like carrier housings, planetary gears, bearings, seals, and brake discs. Safety notices are included to handle fluids properly and avoid injury from released spring forces during disassembly.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
Caterpillar cat m315 f wheeled excavator (prefix f4d) service repair manual (...ifkkdmdmdm
The document provides disassembly instructions for the front and rear final drive carriers, hubs, and brakes of an M315F wheeled excavator. It lists required tools and gives step-by-step instructions to remove components such as carrier housings, planetary gears, retaining rings, seals, and bearings. Personal protective equipment is recommended when removing springs. Overall the document provides detailed guidance to disassemble the drive train components.
The document provides disassembly instructions for the front and rear final drive carriers, hubs, and brakes of an M315F wheeled excavator. It lists required tools and gives step-by-step instructions to remove components such as carrier housings, planetary gears, retaining rings, seals, and bearings. Safety notices are included to warn of risks like contained fluids and released spring forces.
The document provides disassembly instructions for the front and rear final drive carriers, hubs, and brakes of an M315F wheeled excavator. It lists required tools and gives step-by-step instructions to remove components such as carrier housings, planetary gears, retaining rings, seals, and bearings. Safety notices are included to warn of risks like contained fluids and released spring forces.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a multi-step process for removing components like carrier housings, planetary gears, bearings, seals, and brake discs. Safety notices are included to handle fluids properly and avoid injury from released spring forces. Detailed illustrations accompany each step.
Caterpillar cat 430 e backhoe loader (prefix rln) service repair manual (rln0...fjjskekskemmm
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It lists the required tools and describes removing components like gears, shafts, seals and sensors. Detailed illustrations accompany each step to show how to use tools to remove parts and access internal mechanisms. Cleanliness is stressed to prevent dirt entry during disassembly.
Caterpillar cat 430 e backhoe loader (prefix rln) service repair manual (rln0...fjsekksmem
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It lists the required tools and describes removing components like gears, shafts, seals and sensors. Detailed illustrations accompany each step to show how to use tools to remove parts and access internal mechanisms. Cleanliness is stressed to prevent dirt entry during disassembly.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a multi-step process for removing components like carrier housings, planetary gears, bearings, seals, and brake discs. Safety notices are included to handle fluids properly and avoid injury from released spring forces during disassembly.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
Caterpillar cat m315 f wheeled excavator (prefix f4d) service repair manual (...ifkkdmdmdm
The document provides disassembly instructions for the front and rear final drive carriers, hubs, and brakes of an M315F wheeled excavator. It lists required tools and gives step-by-step instructions to remove components such as carrier housings, planetary gears, retaining rings, seals, and bearings. Personal protective equipment is recommended when removing springs. Overall the document provides detailed guidance to disassemble the drive train components.
The document provides disassembly instructions for the front and rear final drive carriers, hubs, and brakes of an M315F wheeled excavator. It lists required tools and gives step-by-step instructions to remove components such as carrier housings, planetary gears, retaining rings, seals, and bearings. Safety notices are included to warn of risks like contained fluids and released spring forces.
The document provides disassembly instructions for the front and rear final drive carriers, hubs, and brakes of an M315F wheeled excavator. It lists required tools and gives step-by-step instructions to remove components such as carrier housings, planetary gears, retaining rings, seals, and bearings. Safety notices are included to warn of risks like contained fluids and released spring forces.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a multi-step process for removing components like carrier housings, planetary gears, bearings, seals, and brake discs. Safety notices are included to handle fluids properly and avoid injury from released spring forces. Detailed illustrations accompany each step.
Caterpillar cat 430 e backhoe loader (prefix rln) service repair manual (rln0...fjjskekskemmm
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It lists the required tools and describes removing components like gears, shafts, seals and sensors. Detailed illustrations accompany each step to show how to use tools to remove parts and access internal mechanisms. Cleanliness is stressed to prevent dirt entry during disassembly.
Caterpillar cat 430 e backhoe loader (prefix rln) service repair manual (rln0...fjsekksmem
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It lists the required tools and describes removing components like gears, shafts, seals and sensors. Detailed illustrations accompany each step to show how to use tools to remove parts and access internal mechanisms. Cleanliness is stressed to prevent dirt entry during disassembly.
This document provides disassembly and assembly instructions for a piston pump used in the hydrostatic power train of a D6K2 LGP track-type tractor. The disassembly process involves 48 steps to remove all individual components of the pump. The assembly process similarly involves assembling the components in the reverse order, noting that cleanliness is important and all parts must be thoroughly cleaned before assembly. Proper tools are required and care must be taken when compressing springs or removing components.
This document provides disassembly and assembly instructions for a piston pump used in the power train of a D6K2 LGP track-type tractor. The disassembly process involves 48 steps to remove all individual components of the pump. The assembly process similarly involves assembling the individual components in the reverse order, noting that cleanliness is important and all parts must be thoroughly cleaned before assembly.
The document provides disassembly instructions for a piston pump in 3 sentences:
It begins by having the user remove the piston pump and clean it before disassembly. Next, it lists 47 detailed steps to disassemble the various components of the pump housing, barrel assembly, valves, and control block. The document emphasizes cleanliness and safety when removing parts under spring pressure.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It lists the required tools and shows illustrations of each step. These include removing the transmission from the loader, draining the oil, and taking apart the various transmission components like gears, shafts, seals and bearings. Detailed procedures are given for disassembling the direct drive, rear output shaft, and other internal transmission parts.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It lists the required tools and shows illustrations of each step. These include removing the transmission from the loader, draining the oil, and taking apart the various transmission components like gears, shafts, seals and casings. Detailed procedures are given for disassembling the direct drive, rear output shaft, input shaft, and transmission case.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It lists the required tools and shows illustrations of each step. These include removing the transmission from the loader, draining the oil, and taking apart the various transmission components like gears, shafts, seals and bearings. Detailed procedures are given for disassembling the direct drive, rear output shaft, and other internal transmission parts.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 70 individual parts in over 40 steps, using various tools. The transmission is first removed and mounted on a stand before dismantling begins with external components like seals, gears, shafts, and casings. Internal components like bearings, synchronizers, and seals are then individually removed from the transmission case. Precise procedures aim to contain fluids and prevent damage to parts.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 70 individual parts in over 40 steps, using various tools. The transmission is first removed from the vehicle and mounted on a stand. Components like gears, shafts, seals and housings are then systematically dismantled using presses, pullers and other tools to remove bearings, seals, springs and other internal pieces. Detailed illustrations accompany each step to show how to access and remove each part.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It lists the required tools and shows illustrations of each step. These include removing the transmission from the loader, draining the oil, and taking apart the various transmission components like gears, shafts, seals and casings using specialized tools. Detailed photographs accompany the text to clearly show how to disassemble the transmission into its core parts.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 20 components of the transmission, including the case, gears, shafts, seals, and sensors. Tools required are listed. Detailed illustrations accompany each step to show how to access and remove each part. Safety notices are included to handle springs and contain fluids.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 20 components of the transmission, including the case, gears, shafts, seals, and sensors. Tools required are listed. Detailed illustrations accompany each step to show how to access and remove each part. Safety notices are included to handle springs and contain fluids.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 70 individual parts in over 40 steps, using various tools. The transmission is first removed from the vehicle and mounted on a stand. Components like gears, shafts, seals and housings are then systematically dismantled using presses, pullers and other tools to remove bearings, seals, springs and other internal pieces. Detailed illustrations accompany each step to show how to remove each part in the correct order.
This document provides instructions for disassembling the output transfer gears of a 740B articulated truck. The steps include removing various components such as hoses, bolts, washers, tubes, seals, gears, carriers, shafts, and housings. Over 40 individual steps are outlined to fully disassemble the output transfer gears, with each step accompanied by an illustration for clarity. Required tools are listed at the beginning.
This document provides instructions for disassembling the output transfer gears of a 740B articulated truck. The steps include removing various components such as hoses, bolts, washers, tubes, seals, gears, carriers, shafts, and housings. Over 40 individual steps are outlined to fully disassemble the output transfer gears, with each step accompanied by an illustration for clarity. Required tools are listed at the beginning.
This document provides instructions for disassembling the output transfer gears on a 740B articulated truck. It lists 50 steps to remove various components such as gears, shafts, seals, housings and more. Special tools are required and components must be removed in a specific order. Safety precautions are noted, such as supporting heavy parts with lifting devices and cribbing. Detailed illustrations accompany each step to show the correct disassembly process.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix RGA) Service Repair Manual...gongfuao7509
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, a barrel and other components into the motor housing in the specified order.
3. Attaching lifting brackets and safely lifting the heavy swing motor or drive components during removal and installation procedures.
Caterpillar Cat 329D and 329D L Excavator (Prefix DTZ) Service Repair Manual ...gongfuao7509
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover and removing mounting bolts.
3. Installing the new regulator by reversing the removal steps, filling the cooling system, and tightening all connections to the specified torques.
Cleanliness is important to prevent contamination, and safety precautions are described for working with hot coolant and steam.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...gongfuao7509
This document provides instructions to disassemble a travel motor. It begins by having the technician remove the travel motor and attach it to assembly tools. It then lists 28 steps to fully disassemble the travel motor by removing components like caps, springs, seals, plates and housing assemblies. Safety notices are included throughout to warn of potential injury from released spring forces.
Caterpillar Cat 324E L Excavator (Prefix PNW) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for disassembling and assembling the travel motor of a 324E L Excavator. It lists the required tools and parts and provides 28 steps to disassemble the travel motor by removing components like the head, O-rings, springs, brake piston, plates, and bearings. It then lists 19 steps to assemble the travel motor by reinstalling these components in the reverse order, noting proper lubrication and alignment of parts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
Caterpillar Cat 324D FM LL EXCAVATOR (Prefix JLS) Service Repair Manual Insta...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of a 324D FM LL EXCAVATOR. It outlines 21 steps for disassembly, which include removing plates, springs, pistons, gears, and other components. It also outlines 16 steps for assembly, which include installing bearings, seals, gears, and other components back into the final drive housing using various tools. The document includes illustrations to supplement the written instructions.
Caterpillar Cat 323F SA and 323F LN Excavator (Prefix FA2) Service Repair Man...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of an excavator model 323F SA. It lists 30 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then lists 31 steps to reassemble the final drive by installing components like bearings, seals, gears, and shims in the reverse order of disassembly. Precise tools and procedures are required due to the heavy weight and precision fitting of components.
More Related Content
Similar to Caterpillar Cat 318F L Excavator (Prefix HCP) Service Repair Manual Instant Download.pdf
This document provides disassembly and assembly instructions for a piston pump used in the hydrostatic power train of a D6K2 LGP track-type tractor. The disassembly process involves 48 steps to remove all individual components of the pump. The assembly process similarly involves assembling the components in the reverse order, noting that cleanliness is important and all parts must be thoroughly cleaned before assembly. Proper tools are required and care must be taken when compressing springs or removing components.
This document provides disassembly and assembly instructions for a piston pump used in the power train of a D6K2 LGP track-type tractor. The disassembly process involves 48 steps to remove all individual components of the pump. The assembly process similarly involves assembling the individual components in the reverse order, noting that cleanliness is important and all parts must be thoroughly cleaned before assembly.
The document provides disassembly instructions for a piston pump in 3 sentences:
It begins by having the user remove the piston pump and clean it before disassembly. Next, it lists 47 detailed steps to disassemble the various components of the pump housing, barrel assembly, valves, and control block. The document emphasizes cleanliness and safety when removing parts under spring pressure.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It lists the required tools and shows illustrations of each step. These include removing the transmission from the loader, draining the oil, and taking apart the various transmission components like gears, shafts, seals and bearings. Detailed procedures are given for disassembling the direct drive, rear output shaft, and other internal transmission parts.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It lists the required tools and shows illustrations of each step. These include removing the transmission from the loader, draining the oil, and taking apart the various transmission components like gears, shafts, seals and casings. Detailed procedures are given for disassembling the direct drive, rear output shaft, input shaft, and transmission case.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It lists the required tools and shows illustrations of each step. These include removing the transmission from the loader, draining the oil, and taking apart the various transmission components like gears, shafts, seals and bearings. Detailed procedures are given for disassembling the direct drive, rear output shaft, and other internal transmission parts.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 70 individual parts in over 40 steps, using various tools. The transmission is first removed and mounted on a stand before dismantling begins with external components like seals, gears, shafts, and casings. Internal components like bearings, synchronizers, and seals are then individually removed from the transmission case. Precise procedures aim to contain fluids and prevent damage to parts.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 70 individual parts in over 40 steps, using various tools. The transmission is first removed from the vehicle and mounted on a stand. Components like gears, shafts, seals and housings are then systematically dismantled using presses, pullers and other tools to remove bearings, seals, springs and other internal pieces. Detailed illustrations accompany each step to show how to access and remove each part.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It lists the required tools and shows illustrations of each step. These include removing the transmission from the loader, draining the oil, and taking apart the various transmission components like gears, shafts, seals and casings using specialized tools. Detailed photographs accompany the text to clearly show how to disassemble the transmission into its core parts.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 20 components of the transmission, including the case, gears, shafts, seals, and sensors. Tools required are listed. Detailed illustrations accompany each step to show how to access and remove each part. Safety notices are included to handle springs and contain fluids.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 20 components of the transmission, including the case, gears, shafts, seals, and sensors. Tools required are listed. Detailed illustrations accompany each step to show how to access and remove each part. Safety notices are included to handle springs and contain fluids.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 70 individual parts in over 40 steps, using various tools. The transmission is first removed from the vehicle and mounted on a stand. Components like gears, shafts, seals and housings are then systematically dismantled using presses, pullers and other tools to remove bearings, seals, springs and other internal pieces. Detailed illustrations accompany each step to show how to remove each part in the correct order.
This document provides instructions for disassembling the output transfer gears of a 740B articulated truck. The steps include removing various components such as hoses, bolts, washers, tubes, seals, gears, carriers, shafts, and housings. Over 40 individual steps are outlined to fully disassemble the output transfer gears, with each step accompanied by an illustration for clarity. Required tools are listed at the beginning.
This document provides instructions for disassembling the output transfer gears of a 740B articulated truck. The steps include removing various components such as hoses, bolts, washers, tubes, seals, gears, carriers, shafts, and housings. Over 40 individual steps are outlined to fully disassemble the output transfer gears, with each step accompanied by an illustration for clarity. Required tools are listed at the beginning.
This document provides instructions for disassembling the output transfer gears on a 740B articulated truck. It lists 50 steps to remove various components such as gears, shafts, seals, housings and more. Special tools are required and components must be removed in a specific order. Safety precautions are noted, such as supporting heavy parts with lifting devices and cribbing. Detailed illustrations accompany each step to show the correct disassembly process.
Similar to Caterpillar Cat 318F L Excavator (Prefix HCP) Service Repair Manual Instant Download.pdf (15)
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix RGA) Service Repair Manual...gongfuao7509
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, a barrel and other components into the motor housing in the specified order.
3. Attaching lifting brackets and safely lifting the heavy swing motor or drive components during removal and installation procedures.
Caterpillar Cat 329D and 329D L Excavator (Prefix DTZ) Service Repair Manual ...gongfuao7509
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover and removing mounting bolts.
3. Installing the new regulator by reversing the removal steps, filling the cooling system, and tightening all connections to the specified torques.
Cleanliness is important to prevent contamination, and safety precautions are described for working with hot coolant and steam.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...gongfuao7509
This document provides instructions to disassemble a travel motor. It begins by having the technician remove the travel motor and attach it to assembly tools. It then lists 28 steps to fully disassemble the travel motor by removing components like caps, springs, seals, plates and housing assemblies. Safety notices are included throughout to warn of potential injury from released spring forces.
Caterpillar Cat 324E L Excavator (Prefix PNW) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for disassembling and assembling the travel motor of a 324E L Excavator. It lists the required tools and parts and provides 28 steps to disassemble the travel motor by removing components like the head, O-rings, springs, brake piston, plates, and bearings. It then lists 19 steps to assemble the travel motor by reinstalling these components in the reverse order, noting proper lubrication and alignment of parts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
Caterpillar Cat 324D FM LL EXCAVATOR (Prefix JLS) Service Repair Manual Insta...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of a 324D FM LL EXCAVATOR. It outlines 21 steps for disassembly, which include removing plates, springs, pistons, gears, and other components. It also outlines 16 steps for assembly, which include installing bearings, seals, gears, and other components back into the final drive housing using various tools. The document includes illustrations to supplement the written instructions.
Caterpillar Cat 323F SA and 323F LN Excavator (Prefix FA2) Service Repair Man...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of an excavator model 323F SA. It lists 30 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then lists 31 steps to reassemble the final drive by installing components like bearings, seals, gears, and shims in the reverse order of disassembly. Precise tools and procedures are required due to the heavy weight and precision fitting of components.
Caterpillar Cat 323D2 and 323D2 L Excavator (Prefix JEX) Service Repair Manua...gongfuao7509
The document provides instructions for disassembling the final drive of an excavator model 323D2. It involves 33 steps including removing the final drive cover, carrier assembly, ring gears, and other components. Various tools are required including a transmission repair stand, link brackets, forcing screws, and puller assembly. Cleanliness is important to prevent dirt from entering internal parts during disassembly.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual Instant ...gongfuao7509
The document provides instructions for removing the engine oil filter base from a 322C FM excavator with a 3126 engine. The procedure involves first removing the turbocharger. Then, using a strap wrench, loosen the oil filter base by turning it counterclockwise. Finally, clean the oil filter base mounting surface before installing the new oil filter base. The summary is provided in 3 sentences or less as requested.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual Instant ...gongfuao7509
1. The document provides instructions for removing and installing the unit injector hydraulic pump and turbocharger on a Caterpillar 3126B engine.
2. The unit injector hydraulic pump removal instructions include disconnecting lines and harness, removing mounting bolts, and inspecting seals. Installation is the reverse of removal.
3. Turbocharger removal requires removing bolts and nuts connecting it to the exhaust manifold and disconnecting oil lines. Disassembly separates the housing components. Assembly reconnects the parts and installation bolts the turbocharger back into place.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual Instant ...gongfuao7509
This document provides instructions for removing and installing a governor from a 322C FM excavator engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to remove the governor. The installation procedure outlines cleaning and lubricating parts, replacing seals, and using tools to install the governor along with associated lines, pins, and clips. Precautions are given to keep parts clean and ensure free movement of components.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The procedures include removing pins and bolts to separate the various linkage and cylinder components, as well as instructions for installing replacement components and adjusting clearances using shims. Proper lubrication of pins, bolts and other components is emphasized during assembly.
Caterpillar Cat 322B L EXCAVATOR (Prefix 1YS) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for removing and installing the governor and associated components on a Caterpillar 3116 engine. The removal process involves disconnecting linkages and tubes, removing mounting bolts and clips, and using specialized tools. The installation follows the removal steps in reverse, applying lubricant to seals and ensuring proper adjustment of linkages. Required tools include various pliers and pin tools to facilitate disconnecting and reconnecting components.
Caterpillar Cat 322 L EXCAVATOR (Prefix 9RL) Service Repair Manual Instant Do...gongfuao7509
This document provides instructions for removing and installing a governor from a Caterpillar Cat 322 L excavator powered by a 3116 engine. The removal procedure involves disconnecting tubes, removing clips and bolts, and using special tools. The installation procedure describes cleaning and lubricating parts, replacing seals, and using tools to install the governor components in reverse order of removal. Proper torque specifications and checks are listed to ensure correct installation.
This document provides instructions for servicing the air conditioning system on Caterpillar 322 and 322L excavators. It describes safety precautions when working with refrigerant due to risks of injury. The document outlines procedures for preparing the machine, removing and installing various AC system components like lines, the compressor, and preparing the system for disassembly and reassembly. Detailed steps are provided for correctly assembling refrigerant line fittings and other components.
Caterpillar Cat 320F L Excavator (Prefix YBM) Service Repair Manual Instant D...gongfuao7509
The document provides instructions for removing and installing a boom cylinder on an excavator. Key steps include:
1. Lowering the boom and releasing hydraulic pressure before removal.
2. Detaching hoses and removing bolts and pins to separate the cylinder from the excavator.
3. Lifting the cylinder, which weighs approximately 287kg, off the excavator using slings.
4. Reinstalling involves lifting the cylinder back into place with slings, reattaching with bolts and pins, and reconnecting hoses. Torque specifications are provided for all fasteners.
This document provides instructions for removing and installing a flywheel on a 320E LRR excavator with a C6.6 engine. The removal procedure involves using guide studs and lifting equipment to support the flywheel, then removing mounting bolts. The installation procedure specifies cleaning and inspecting components, positioning the flywheel with guide studs and lifting equipment, and tightening mounting bolts to the specified torque. Instructions are also provided for removing and installing a crankshaft rear seal.
This document provides instructions for removing and installing various engine components on a Caterpillar 320E LRR excavator, including:
1. Removing and installing the crankshaft front seal using specific tools.
2. Removing and installing the front cover, which requires removing bolts in a specific order and position.
3. Installing a new gasket and front seal when reinstalling the front cover.
The document contains detailed step-by-step instructions and illustrations for performing maintenance on the engine's crankshaft pulley, vibration damper, front seal, and front cover. Precautions are provided to keep parts clean and torque specifications are given.
This document provides instructions for disassembling and assembling the gear pump (pilot) and main hydraulic pump on a Caterpillar 320D2 excavator. The summary includes steps to disassemble the gear pump by removing housing bolts, seals, gears, and plates. It also describes removing the main hydraulic pump by disconnecting hoses and harnesses, removing mounting bolts, and lifting out the pump along with attached auxiliary pumps and pilots.
The document provides instructions for disassembling and assembling the travel motor of a 320D2L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, check valves, fittings, pistons, plates, seals and more. It then describes 25 steps to reassemble the travel motor, replacing components in the reverse order and ensuring proper alignment of parts like keys and cam plates. Special care must be taken to avoid damaging parts and keep components matched during assembly.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318F L EXCAVATOR HCP
Configuration: 318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
316F, 318F Excavator Machine Systems
Media Number -UENR5585-06 Publication Date -01/08/2015 Date Updated -12/09/2018
i07505849
Travel Motor - Disassemble
SMCS - 4351-015
S/N - HCP1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1P-2420 Transmission Repair Stand 1
FT-0957 Positioning Gp 4
B
- M16x2 Threaded Rod 3
8T-1757 Nut 6
9X-8268 Washer 6
C 421-5662 Lifting Eye Assembly 1
D 421-5663 Lifting Eye Assembly 2
E
1U-9895 Crossblock 1
3H-0465 Push-Puller Plate 2
8T-0298 Bolt 2
Start By:
a. Remove the travel motor.
1/13
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g06341880
1. Attach the travel motor to Tooling (A) and (B). The weight of the travel motor is
approximately 70 kg (154 lb).
2. Remove plugs (1) and the O-ring seals.
Illustration 2 g06344110
3. Remove plug (2) and the O-ring seal. Repeat for the opposite side.
Illustration 3 g06341912
2/13
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove plug (2A) and the O-ring seal. Repeat for the opposite side.
Illustration 4 g06341915
5. Remove spring (3).
Illustration 5 g06341917
6. Remove spool (4).
3/13
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g06341942
Illustration 7 g06342000
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7. Remove bolts (5) and cap (6). Repeat for the opposite side.
8. Remove O-ring seal (10) from cap (6). Remove guide (9), spring (8), and washer (7) from
the head assembly. Repeat for the opposite side.
4/13
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g06342005
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove plug (11), O-ring seal (12), spring (13), and ball (14) from cap (6). Repeat for the
other cap.
Illustration 9 g06342009
10. Remove spool (15).
5/13
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g06343314
Illustration 11 g06343315
11. Remove relief valve (16). Remove O-ring seal (17) from relief valve (16).
12. Repeat for the opposite side.
Illustration 12 g06343359
6/13
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
13. Remove the nuts of Tooling (B). Remove bolts (19) from head assembly (18).
Illustration 13 g06343366
14. Use Tooling (C) and a suitable lifting device to remove head assembly (18). The weight of
head assembly (18) is approximately 21 kg (47 lb).
Illustration 14 g06343374
15. Remove control plate (20) and bearing (21) from head assembly (18).
7/13
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g06343381
16. Remove pins (22) and springs (23).
17. Remove O-ring seals (24) and (25).
Illustration 16 g06343383
18. Use Tooling (D) and a suitable lifting device to remove housing assembly (26) from
Tooling (A) and place on a suitable bench.
Illustration 17 g06343417
8/13
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. To avoid personal injury, always wear eye and face protection when
using pressurized air.
19. Attach Tooling (E) to housing (26). Use air pressure to unseat brake piston (27). Remove
Tooling (E) and brake piston (27).
Illustration 18 g06343437
20. Remove back up rings (28) and O-ring seals (29) from brake piston (27).
Illustration 19 g06343462
21. Remove brake piston guide (30).
9/13
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g06343464
22. Remove O-ring seal (31) from brake piston guide (30).
Illustration 21 g06343466
Illustration 22 g06343469
Note: Note the orientation of friction discs (32) and plates (33) for assembly purposes.
23. Remove friction discs (32) and plates (33).
10/13
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M007...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g06343638
24. Remove rotating group (34) from housing (26).
Illustration 24 g06343777
25. Remove pistons (35) and retainer (36) from barrel (37).
Illustration 25 g06343783
26. Remove hold down ball (38) and springs (39) from barrel (37).
11/13
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M007...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g06343786
27. Remove swashplate (40) from housing (26).
Illustration 27 g06343788
Illustration 28 g06343793
28. Remove pistons (41).
29. Remove springs (42) and shaft (43).
12/13
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M007...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 29 g06343795
30. Remove balls (46).
31. Remove bearing (44) and lip seal (45).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 13:04:51 UTC+0800 2020
13/13
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M007...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318F L EXCAVATOR HCP
Configuration: 318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
316F, 318F Excavator Machine Systems
Media Number -UENR5585-06 Publication Date -01/08/2015 Date Updated -12/09/2018
i07505850
Travel Motor - Assemble
SMCS - 4351-016
S/N - HCP1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1P-2420 Transmission Repair Stand 1
FT-0957 Positioning Gp 4
B
- M16x2 Threaded Rod 3
8T-1757 Nut 6
9X-8268 Washer 6
C 421-5662 Lifting Eye Assembly 1
D 421-5663 Lifting Eye Assembly 2
1/12
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g06343795
1. Install lip seal (45) and bearing (44).
2. Install balls (46).
Illustration 2 g06343793
Illustration 3 g06343788
3. Install shaft (43) and springs (42).
4. Install pistons (41).
2/12
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g06343786
5. Install swashplate (40) into housing (26).
Illustration 5 g06343783
6. Install springs (39) and hold down ball (38) into barrel (37).
Illustration 6 g06343777
7. Install retainer (36) and piston (35) into barrel (37).
3/12
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 7 g06343638
8. Install rotating group (34) into housing (26).
Illustration 8 g06343469
Illustration 9 g06343466
9. Install plates (33) and friction discs (32) in the orientation determined in the disassembly.
4/12
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 10 g06343464
10. Install O-ring seal (31) into brake piston guide (30).
Illustration 11 g06343462
11. Install brake piston guide (30).
Illustration 12 g06343437
12. Install O-ring seals (29) and back up rings (28) into brake piston (27).
5/12
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 13 g06343877
13. Use Tooling (D) and a suitable lifting device to position housing (26) onto Tooling (A) and
(B). The weight of housing (26) is approximately 43 kg (95 lb).
14. Remove Tooling (D) and install brake piston (27).
Illustration 14 g06343381
15. Install O-ring seals (25) and (24).
16. Install springs (23) and pins (22).
Illustration 15 g06343374
6/12
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 17. Install bearing (21) and control plate (20) into head assembly (18).
Illustration 16 g06343366
18. Use Tooling (C) and a suitable lifting device to install head assembly (18) onto the housing.
The weight of head assembly (18) is approximately 21 kg (47 lb).
Illustration 17 g06343887
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
19. Install bolts (19). Tighten bolts (19) to a torque of 205 ± 10 N·m (151 ± 7 lb ft).
20. Install the bolts of Tooling (B)
7/12
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 18 g06343315
Illustration 19 g06343314
21. Install O-ring seal (17) onto relief valve (16).
22. Install relief valve (16) into the head assembly. Tighten relief valve (16) to a torque of
570 ± 20 N·m (420 ± 14 lb ft). Repeat for the opposite side.
Illustration 20 g06342009
23. Install spool (15).
8/12
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 21 g06342005
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
24. Install O-ring seal (12) onto plug (11).
25. Install ball (14), spring (13), and plug (11) into cap (6). Repeat for the opposite side.
Illustration 22 g06342000
9/12
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M00708...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 23 g06341942
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
26. Install O-ring seal (10) onto cap (6).
27. Install washer (7), spring (8), guide (9), and cap (6) into the head assembly.
28. Repeat for the opposite side.
Illustration 24 g06341917
29. Install spool (4).
10/12
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M007...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
26. Illustration 25 g06341915
30. Install spring (3).
Illustration 26 g06341912
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
31. Install plug (2A). Tighten plug (2A) to a torque of 54 ± 5 N·m (40 ± 4 lb ft). Repeat for the
opposite side.
11/12
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine(M007...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...