The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Removing and installing the flywheel housing which requires lifting tools and removing/installing bolts.
- Removing the vibration damper and crankshaft pulley which requires socket tools and a combination puller to remove bolts and nuts.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...shudun96087
The document provides instructions for removing and installing a flywheel housing on a 3046 engine. It describes:
1) Removing the 12 bolts and washers securing the flywheel housing and lifting it off using a lifting bracket.
2) Cleaning the mating surfaces and installing a new gasket before positioning the housing back on.
3) Reinstalling the 12 bolts and washers and removing the lifting bracket to complete the installation.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...shudun96087
The document provides instructions for removing and installing a flywheel housing on a 3046 engine. It describes:
1) Removing the 12 bolts and washers securing the flywheel housing and lifting it off using a lifting bracket.
2) Cleaning the mating surfaces and installing a new gasket before positioning the housing back on.
3) Reinstalling the 12 bolts and washers and removing the lifting bracket to complete the installation.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jse7039222
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jse7039222
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...kesi7153062
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...kesi7153062
The document provides instructions for removing and installing a flywheel housing on a 3046 engine. It describes:
1) Removing the 12 bolts and washers securing the flywheel housing and lifting it off using a lifting bracket.
2) Cleaning the mating surfaces and installing a new gasket before positioning the housing back on.
3) Reinstalling the 12 bolts and washers and removing the lifting bracket to complete the installation.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Removing and installing the flywheel housing which requires lifting tools and removing/installing bolts.
- Removing the vibration damper and crankshaft pulley which requires socket tools and a combination puller to remove bolts and nuts.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...shudun96087
The document provides instructions for removing and installing a flywheel housing on a 3046 engine. It describes:
1) Removing the 12 bolts and washers securing the flywheel housing and lifting it off using a lifting bracket.
2) Cleaning the mating surfaces and installing a new gasket before positioning the housing back on.
3) Reinstalling the 12 bolts and washers and removing the lifting bracket to complete the installation.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...shudun96087
The document provides instructions for removing and installing a flywheel housing on a 3046 engine. It describes:
1) Removing the 12 bolts and washers securing the flywheel housing and lifting it off using a lifting bracket.
2) Cleaning the mating surfaces and installing a new gasket before positioning the housing back on.
3) Reinstalling the 12 bolts and washers and removing the lifting bracket to complete the installation.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jse7039222
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jse7039222
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...kesi7153062
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...kesi7153062
The document provides instructions for removing and installing a flywheel housing on a 3046 engine. It describes:
1) Removing the 12 bolts and washers securing the flywheel housing and lifting it off using a lifting bracket.
2) Cleaning the mating surfaces and installing a new gasket before positioning the housing back on.
3) Reinstalling the 12 bolts and washers and removing the lifting bracket to complete the installation.
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, and hub. The assembly procedure provides steps to install 23 components in reverse order and includes checking brake clearance and installing seals and bearings. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
Caterpillar Cat M312 Excavator (Prefix 6TL) Service Repair Manual (6TL00001-0...paws21610697
This document provides the disassembly and assembly procedures for the swing drive of an M312 excavator. The disassembly procedure involves 28 steps to remove components such as the swing brake assembly, discs, plates, piston, seals, shaft, gears, bearings, and housing. The assembly procedure involves 17 steps and requires various tools to install components in the reverse order of disassembly while applying lubricant and ensuring proper torque specifications are achieved.
This document provides instructions for removing and installing engine oil filter bases and related components on Caterpillar 3304B and 3306B engines. The procedures describe removing the oil filter, oil filter base, gaskets and O-rings. Instructions are provided for disassembling the oil filter base by removing covers, bolts, springs and plungers. Reassembly and installation steps are also outlined. Tools required are listed for each procedure. Precautions are noted to keep parts clean and contain fluids.
Caterpillar Cat D250E II Articulated Truck (Prefix 4PS) Service Repair Manual...paws21610697
The document provides instructions for disassembling and assembling the piston pump used for steering on a D250E II Articulated Truck. The disassembly procedure involves removing 21 individual parts from the pump housing. The assembly procedure instructs assembling the 21 parts in the reverse order, applying lubrication and torque specifications as needed. Tools required include various drivers, pliers, and lubricants.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling a Type I governor used in Caterpillar 3114, 3116, and 3126 engines. It describes 35 steps to disassemble the governor front housing and 19 additional steps to disassemble the rear housing. Various parts are inspected for wear or damage during disassembly. Cleaning and replacement parts are also discussed. Tools required are listed.
The document provides instructions for removing and installing various engine components on a Caterpillar 3408 industrial engine, including the oil cooler, oil filter base, oil bypass valves, engine oil cooler/lines, aftercooler, and turbocharger. The procedures describe removing bolts, hoses, seals, and other parts, cleaning components, applying sealant, and reinstalling parts in reverse order.
The document provides instructions for removing and installing wheel spindles on Caterpillar articulated dump trucks. It describes removing the wheels, bearings, and seals before removing the brake shoes. It then details removing pins and springs to separate the brake shoes from the spider. Reinstallation follows the reverse order. Instructions are also given for disassembling and assembling suspension cylinders.
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, and hub. The assembly procedure provides steps to install 23 components in reverse order and includes checking brake clearance and installing seals and bearings. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
Caterpillar Cat M312 Excavator (Prefix 6TL) Service Repair Manual (6TL00001-0...paws21610697
This document provides the disassembly and assembly procedures for the swing drive of an M312 excavator. The disassembly procedure involves 28 steps to remove components such as the swing brake assembly, discs, plates, piston, seals, shaft, gears, bearings, and housing. The assembly procedure involves 17 steps and requires various tools to install components in the reverse order of disassembly while applying lubricant and ensuring proper torque specifications are achieved.
This document provides instructions for removing and installing engine oil filter bases and related components on Caterpillar 3304B and 3306B engines. The procedures describe removing the oil filter, oil filter base, gaskets and O-rings. Instructions are provided for disassembling the oil filter base by removing covers, bolts, springs and plungers. Reassembly and installation steps are also outlined. Tools required are listed for each procedure. Precautions are noted to keep parts clean and contain fluids.
Caterpillar Cat D250E II Articulated Truck (Prefix 4PS) Service Repair Manual...paws21610697
The document provides instructions for disassembling and assembling the piston pump used for steering on a D250E II Articulated Truck. The disassembly procedure involves removing 21 individual parts from the pump housing. The assembly procedure instructs assembling the 21 parts in the reverse order, applying lubrication and torque specifications as needed. Tools required include various drivers, pliers, and lubricants.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling a Type I governor used in Caterpillar 3114, 3116, and 3126 engines. It describes 35 steps to disassemble the governor front housing and 19 additional steps to disassemble the rear housing. Various parts are inspected for wear or damage during disassembly. Cleaning and replacement parts are also discussed. Tools required are listed.
The document provides instructions for removing and installing various engine components on a Caterpillar 3408 industrial engine, including the oil cooler, oil filter base, oil bypass valves, engine oil cooler/lines, aftercooler, and turbocharger. The procedures describe removing bolts, hoses, seals, and other parts, cleaning components, applying sealant, and reinstalling parts in reverse order.
The document provides instructions for removing and installing wheel spindles on Caterpillar articulated dump trucks. It describes removing the wheels, bearings, and seals before removing the brake shoes. It then details removing pins and springs to separate the brake shoes from the spider. Reinstallation follows the reverse order. Instructions are also given for disassembling and assembling suspension cylinders.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B N EXCAVATOR 7KZ
Configuration: 318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01646268
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00527024
1. Install Tool (A), a strap, and a suitable lifting device onto flywheel (2) .
2. Remove six bolts (1) that secure flywheel (2) from the crankshaft.
3. Remove flywheel (2). The weight of the flywheel is 50 kg (110 lb).
Note: Dowel pin hole (3) is slightly offset in order to ensure correct installation.
4. Check the condition of the dowels (not shown). If the dowels are damaged, use new parts
for replacement.
Illustration 2 g00527069
5. Check the condition of the ring gear (4). Replace the ring gear with a new part if the gear is
worn or damaged.
6. Place flywheel (2) and ring gear (4) on a suitable support.
Note: Identify the orientation of the ring gear on the flywheel for the correct positioning
when the new ring gear is installed.
7. Use a hammer and a punch in order to remove ring gear (4) from the flywheel.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Dec 1 10:38:04 UTC+0800 2020
2/2
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B N EXCAVATOR 7KZ
Configuration: 318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01646270
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Use an oven and heat ring gear (2) to a maximum temperature of 150 °C (302 °F). Install
the ring gear.
1/3
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00562859
2. Position the ring gear (4) on flywheel (2) .
Illustration 2 g00527024
3. Check the condition of the dowels (not shown). If the dowels are damaged, use new parts
for replacement.
4. Install Tool (A), a strap, and a suitable lifting device onto flywheel (2) .
5. Install flywheel (2). The weight of the flywheel is 50 kg (110 lb).
Note: Dowel pin hole (3) is slightly offset in order to ensure correct installation.
6. Install six bolts (1) in order to secure flywheel (2) onto the crankshaft. Tighten the bolts to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
7. Remove Tool (A) .
8. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect" for more
information on flywheel runout.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Tue Dec 1 10:39:03 UTC+0800 2020
2/3
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B N EXCAVATOR 7KZ
Configuration: 318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i05485410
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller Gp 1
Start By:
A. Remove the flywheel.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00527955
1. Drill three evenly spaced 3 mm (.12 inch) holes in crankshaft rear seal (1) .
2. Use Tool (A) in order to remove the crankshaft rear seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Dec 1 10:40:03 UTC+0800 2020
2/2
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B N EXCAVATOR 7KZ
Configuration: 318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i05485391
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 438-3244 Oil Seal Installer 1
B 438-3245 Seal Adapter 1
C 6V-3303 Bolt 1
D 4B-5275 Washer 1
E 9U-6172 Bolt 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft rear seal.
1/2
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g00528113
2. Position Tooling (B) onto the crankshaft and install Tooling (E) .
Note: Be sure that Tooling (B) is correctly aligned with the crankshaft.
3. Put new crankshaft rear seal (1) in Tooling (A) .
4. Install Tooling (C) , Tooling (D) , and Tooling (A) on Tooling (B) .
5. Push crankshaft rear seal (1) onto the crankshaft until Tooling (A) bottoms out.
6. Remove the tooling from the crankshaft. Check the crankshaft rear seal for correct
installation.
End By: Install the flywheel.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Dec 1 10:41:02 UTC+0800 2020
2/2
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B N EXCAVATOR 7KZ
Configuration: 318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01646275
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 135-7575 Link Bracket 1
Start By:
A. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
B. Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear
Seal - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00528388
1. Install Tool (A), a strap, and a suitable lifting device onto flywheel housing (1) .
2. Remove twelve bolts (2) and the washers that secure flywheel housing (1) to the cylinder
block.
3. Remove flywheel housing (1). The weight of the flywheel is 30 kg (66 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g00528389
1. Check the condition of two dowels (4). If dowels (4) are damaged, use new parts for
replacement.
2. Clean old gasket material (3) from the surfaces of the cylinder block and the flywheel
housing that contact each other. Install a new gasket on the cylinder block (not shown).
Illustration 3 g00528388
3. Install flywheel housing (1) .
4. Install the washers and twelve bolts (2) in order to secure flywheel housing (3) to the
cylinder block.
5. Remove Tool (A) .
End By:
a. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
b. Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal -
Install".
Tue Dec 1 10:42:02 UTC+0800 2020
3/4
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B N EXCAVATOR 7KZ
Configuration: 318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01646277
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-9120 Socket (1) 1
is
B 1P-2321 Combination Puller 1
( 1 )
Tool (A) is a 46 mm socket.
Start By:
A. Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00528749
1. Remove six bolts (1) and the washers from vibration damper (2). Remove vibration damper
(2) from crankshaft pulley (5) .
Note: Inspect the vibration damper for leaks and dents. If either condition exists, replace the
vibration damper with a new part.
2.
Illustration 2 g00559259
3. Use Tool (A) and remove nut (3) and the washer from the crankshaft.
2/4
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00559308
4. If necessary, use Tool (B) and remove crankshaft pulley (5) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00559259
1. Install crankshaft pulley (5) with the washer and nut (3) onto crankshaft (4) .
2. Use Tool (A) to tighten nut (3) to a torque of 490 ± 10 N·m (360 ± 7 lb ft). Hit nut (3) with
a hammer and torque the bolt again to 490 ± 10 N·m (360 ± 7 lb ft).
3/4
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 5 g00528749
3. Use six bolts (1) and the washers in order to install vibration damper (2) on the crankshaft
pulley.
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Dec 1 10:43:01 UTC+0800 2020
4/4
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B N EXCAVATOR 7KZ
Configuration: 318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01027796
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the vibration damper and the crankshaft pulley. Refer to Disassembly and
Assembly, "Vibration Damper and Pulley - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
1. Drill three evenly spaced 3 mm (.12 inch) holes in crankshaft front seal (1) .
2. Use Tool (A) and remove crankshaft front seal (1) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Dec 1 10:44:00 UTC+0800 2020
2/2
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B N EXCAVATOR 7KZ
Configuration: 318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01027827
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
4C-6376 Seal Installer Stud 1
4C-6377 Seal Installer Washer 1
4C-6378 Seal Installer Sleeve 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00529163
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Install new crankshaft front seal (1) with Tool (A) .
3. Remove Tool (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By: Install the vibration damper and the pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Dec 1 10:44:59 UTC+0800 2020
2/2
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B N EXCAVATOR 7KZ
Configuration: 318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01646292
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Before removal, ensure that the marks on the timing gears are in alignment. Align the
fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
Illustration 1 g00559575
Illustration 2 g00559536
1. Remove idler gear bolt (1) and the washer from the idler gear shaft .
2. Remove thrust plate (2) .
3. Remove idler gear (3) .
2/4
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 3 g00559567
Illustration 4 g00559569
4. Use Tool (A) and remove idler shaft (4) from the cylinder block.
Illustration 5 g00559572
5. If necessary, remove five bolts (5) that hold front plate (6) to the cylinder block.
3/4
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. 6. Remove front plate (6) and the gasket.
Note: See the following list for the removal of the other gears in the front gear group.
• In order to remove the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Remove and Install".
• In order to remove the fuel injection pump gear, refer to Disassembly and Assembly, "Fuel
Injection Pump Housing and Governor - Remove".
• In order to remove the gear to the engine oil pump, refer to Disassembly and Assembly,
"Engine Oil Pump - Remove".
• In order to remove the crankshaft front gear, refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Dec 1 10:45:59 UTC+0800 2020
4/4
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B N EXCAVATOR 7KZ
Configuration: 318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01045442
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00559572
1. Install a new gasket and front plate (6) .
Note: Ensure that all mating surfaces are clean and free of old gasket material.
1/3
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 2. Install five bolts (5) that hold front plate (6) to the cylinder block. Tighten these bolts to a
torque of 10 to 13 N·m (7 to 10 lb ft).
Illustration 2 g00559567
3. Install idler shaft (4) onto the cylinder block.
Note: If necessary, cool the idler shaft to 0 °C (32 °F) before installation.
Illustration 3 g00559536
Note: Ensure that the marks on the timing gears are in alignment. Align the fuel injection
drive gear with the "33" mark with the "3" mark on the idler gear. Make an alignment of the
"2" mark on the camshaft gear with the "22" mark on the idler gear. Align the "1" mark on
the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top
center position when these marks are in alignment.
4. Install idler gear (3) .
5. Install thrust plate (2) .
6. Install the washer and idler gear bolt (1) onto thrust plate (2). Tighten idler gear bolt (1) to a
torque of 34 ± 5 N·m (25 ± 4 lb ft).
2/3
318B L & 318B LN Excavators 7KZ00001-UP (MACHINE) POWERED BY 3046 En...
2020/12/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...